Structural, magnetic properties and magnetostriction studies of Sm1−xNdxFe1.55 alloys

Structural, magnetic properties and magnetostriction studies of Sm_1−xNd_xFe_1.55 (0≤x≤0.56) alloys have been performed. X-ray diffraction analysis confirms the presence of single cubic Laves phase in Sm_1-xNd_xFe_1.55 alloys with 0≤x≤0.48. The lattice parameter of alloys increases linearly with increase in Nd content while the Curie temperature behaves in the opposite way. The alloy x=0.08 exhibits a giant magnetostriction value (λ_∥-λ_⊥) of −2187 ppm at a magnetic field of 12 kOe due to the anisotropy compensation between Sm³⁺ and Nd³⁺ ions.     

Anisotropy and FOMP in Tb3 (Fe28−xCox) V1.0 (x=0, 3 and 6) compounds

In this work, the structural and magnetic properties of Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) compounds have been investigated. The structural characterization of compounds by X-ray powder diffraction is an evidence for a monoclinic Nd₃(Fe, Ti)₂₉-type structure (A2/m space group). The refined lattice parameters a and b (but not c) and the unit cell volume V, obtained from the XRD data by the Rietveld method, are found to decrease with increasing Co concentration. The unit cell parameters behavior has been attributed to the smaller Co atoms and a preferential substitution of Fe by Co. The anisotropy field (H_a) as well as critical field (H_cr) was measured using the singular point detection (SPD) technique from 5 to 300 K in a pulsed magnetic field of up to 30 T. At T=5 K, a FOMP of type 2 was observed for all samples and persists at all temperatures up to 300 K. For sample x=0, H_cr=10.6 and 2.0 T at 5 and 300 K, respectively, is equal to that reported earlier. The occurrence of canting angles between the magnetic sublattices during the magnetization process instead of high-order anisotropy contributions (at room temperature are usually negligible) has been considered to explain the survival of the FOMP at room temperature. The anisotropy and critical fields behave differently for samples with x=0, 3 compared with x=6. The observed behavior has been related to the fact that the Co substitution for Fe takes place with a preferential entrance in the inequivalent crystallographic sites of the 3:29 structure. The contribution of the Tb-sublattice in the Tb₃(Fe, V)₂₉ compound with uniaxial anisotropy has been scaled from the anisotropy field measured on a Y₃(Fe, V)₂₉ single crystal with easy plane anisotropy.     

Effect of Co or Mn addition on the soft magnetic properties of amorphous Fe89−xZr11Bx (x=5, 10) alloy ribbons

The temperature and field dependent magnetic properties of melt-spun amorphous Fe_89−x−yZr₁₁B_x(Co,Mn)_y (x=5, 10 and 0≤y≤10) alloys in the temperature range 5-1200 K are reported. The Curie temperature and saturation magnetization at room temperature increase (decrease) almost linearly with Co (Mn) addition. With increasing Co concentration, the room temperature coercivity increases at the rate of 2.26 (0.28) A/m per at% for the x=5 (10) samples. The high-field magnetic susceptibility and local magnetic anisotropy decrease (increases) rapidly with increasing Co (Mn) concentration. The thermomagnetic curves show a marked increase in magnetization above 850 K corresponding to the crystallization of α-FeCo (α-Fe) phase in samples containing Co (Mn). The Curie temperature of the crystalline phase increases (remains same) with increasing Co (Mn) concentration with the formation of α-FeCo (α-Fe). Addition of Co up to 10 at% in Fe-Zr-B improves the room temperature saturation magnetization from 0.56 to 1.2 T, and Curie temperature from 315 to 476 K. Also, the coercivity increases with Co addition from 1.27 to 23.88 A/m for x=5 and from 7.64 to 10.35 A/m for x=10 alloy. The non-collinear spin structures that characterize Fe rich Fe-Zr-B amorphous alloys have been used to describe the observed results.     

Temperature dependence of the coercivity in Nd60Fe30−xCoxAl10, x=0 or 10, and Pr58Fe24Al18 bulk amorphous ferromagnets

Bulk amorphous ferromagnet alloys of composition Nd₆₀Fe₃₀Al₁₀, Nd₆₀Fe₂₀Co₁₀Al₁₀ and Pr₅₈Fe₂₄Al₁₈ have been prepared by argon arc melting and quenching into a copper mould. General insight into the magnetic behaviour of the alloys was gained from measurement of the major hysteresis loop at room temperature, and from zero-field cooled and field-cooled magnetisation measurements in the range 10-400 K. Measurements of the coercivity were made from 10 to 400 K, and for all alloys, the coercivity is seen to increase steeply with decreasing temperature to a peak at a temperature in the range 25-50 K, before decreasing. For all alloys, the temperature dependence of the coercivity between 50 and 400 K is well explained by the strong pinning model of domain walls of Gaunt [Philos. Mag. B 48 (1983) 261]. Quantities deduced from the Gaunt model, along with other relevant magnetic parameters, are used to estimate values for the exchange and anisotropy constants.     

Synthesis and magnetic properties of melt-spun high Pr-content magnetostrictive alloys

Pseudobinary high Pr-content Tb_1−xPr_x(Fe_0.4Co_0.6)_1.93 (0.70≤x≤1.00) magnetostrictive alloys have been fabricated by a melt-spinning method. The effects of the composition, spinning, and annealing processes on the structure, thermal stability, and magnetic properties are investigated. At a wheel speed of v≤30 m/s, the as-spun ribbons consist of a mixture of (Tb,Pr)(Fe,Co)₂ cubic Laves phase and some non-cubic phases. A single (Tb,Pr)(Fe,Co)₂ phase with MgCu₂-type structure is formed with the process for the speed of v≥35 m/s and subsequent annealing at 500 °C for 30 min. The lattice parameter of the Tb_1−xPr_x(Fe_0.4Co_0.6)_1.93 Laves phase increases from 0.7354 nm for x=0.70 to 0.7384 nm for x=1.00 and approximately follows the linear Vegard's law. The Curie temperature decreases, while the saturation magnetization increases as increasing Pr content. The Pr-rich alloys possess the relatively lower coercivity and the faster saturation of magnetostriction as compared with the Tb-rich alloys, which can be understood by their lower magnetic anisotropy.     

Application of the Stoner-Wohlfarth model with interaction for the determination of the saturation magnetisation, anisotropy field, and mean field interaction in bulk amorphous ferromagnets

Magnetic hysteresis curves of bulk amorphous ferromagnet alloys of composition Nd₆₀Fe₃₀Al₁₀, Nd₆₀Fe₂₀Co₁₀Al₁₀ and Pr₅₈Fe₂₄Al₁₈ have been measured in applied magnetic fields up to 9 T at temperatures in the range 10-350 K. The behaviour of the demagnetisation curve in the first quadrant is interpreted using a mean field interaction model as proposed by Callen et al. [Phys. Rev. B 16 (1977) 263], which extends the Stoner-Wohlfarth model [Philos. Trans. Roy. Soc. A 240 (1948) 599] for a random distribution of non-interacting uniaxial grains. Application of the mean field interaction model enables the determination of the saturation magnetisation M_s, anisotropy field H_a, and interaction parameter d, and from these other magnetic parameters, such as the anisotropy constant, K, are deduced. For the three alloys, the temperature dependent behaviour of M_s, H_a, d and K over the range 20-350 K are found to be qualitatively similar, though there are quantitative differences. In all cases M_s increases with decreasing temperature, both H_a and K increase with decreasing temperature, reaching a peak in the range 75-120 K, and then decreasing, and d decreases approximately linearly as the temperature decreases. The physical mechanisms responsible for coercivity in these materials are discussed in the context of random anisotropy and a strong pinning model of domain walls.     

Magnetic and transport properties of granular and Heusler-type glass-coated microwires

We studied magnetic and structural properties of granular Co_xCu_100−x (5<x<40 at%), Cu₆₃Fe₃₇ and Heusler-type Ni₂MnGa glass-coated microwires. We found that the structure of Co–Cu microwires consists of two phases: fcc Cu for all the samples and fcc α-Co present for higher Co content. In the case of low Co content, Co atoms are distributed within the Cu matrix. The quantity and the size of grains strongly depend on the geometry of the microwire. Co–Cu and Fe–Cu microwires exhibited considerable magnetoresistance (MR). For Co_xCu_100−x microwires at x≥30 the anisotropic contribution to MR has been observed. Temperature dependences of magnetization measured without an external magnetic field (ZFC) and in the presence of a field (FC) show considerable difference below 20 K, indicating the presence of small α-Fe or Co grains embedded in the Cu matrix. Annealed Ni₂MnGa microwires showed ferromagnetic behavior with Curie temperature about 330 K and polycrystalline structure with space group I4/mmm and lattice parameters a=3.75 Å and c=6.78 Å.     

Structure and magnetism of the Pr2Fe14-xCoxB system

Isostructural, tetragonal materials were synthesized for the entire composition range (x = 0 to 14). They were studied by X-ray and magnetometry methods. Magnetization measurements confirm a ferromagnetic arrangement of 3d and Pr magnetic moments and reveal a sharp increase of the Curie temperature with the increase of Co concentration. Saturation magnetization at 295 and 77 K reaches a slight maximum around x = 1 and gradually decreases for higher Co content. Anisotropy fields initially decrease and afterwards increase very quickly as more Co is introduced to the system. A spin reorientation occurs in alloys with x ⩾ 9.5 at temperature higher than 660 K. It marks a transition between uniaxial anisotropy and planar anisotropy. Spin reorientation temperature becomes lower for materials with higher Co content. A discussion of the Curie temperature change is conducted in terms of preferential substitution of Co into 16k₂ sites. The weakening of the exchange interaction between Pr and 3d sublattices, as well as the decreasing Pr-sublattice anisotropy with rising temperature, are considered to be responsible for anisotropy field changes. The interplay between crystal field and exchange field interactions is emphasized. A comparison with the Nd₂Fe_14-xCo_xB system is included.     

Effects of TiN coating on the corrosion of nanostructured Ti-30Ta-xZr alloys for dental implants

Electrochemical characteristics of a titanium nitride (TiN)-coated/nanotube-formed Ti-Ta-Zr alloy for biomaterials have been researched by using the magnetic sputter and electrochemical methods. Ti-30Ta-xZr (x = 3, 7 and 15 wt%) alloys were prepared by arc melting and heat treated for 24 h at 1000 °C in an argon atmosphere and then water quenching. The formation of oxide nanotubes was achieved by anodizing a Ti-30Ta-xZr alloy in H₃PO₄ electrolytes containing small amounts of fluoride ions at room temperature. Anodization was carried out using a scanning potentiostat, and all experiments were conducted at room temperature. The microstructure and morphology of nanotube arrays were characterized by optical microscopy (OM), field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD). The TiN coatings were obtained by the radio-frequency (RF) magnetron sputtering technique. The depositions were performed from pure Ti targets on Ti-30Ta-xZr alloys substrates. The corrosion properties of the specimens were examined using potentiodynamic test in a 0.9% NaCl solution by using potentiostat. The microstructures of Ti-30Ta-xZr alloys were changed from an equiaxed to a needle-like structure with increasing Zr content. The interspace between the nanotubes was approximately 20, 80 and 200 nm for Zr contents of 3, 7 and 15 wt%, respectively. The corrosion resistance of the TiN-coated on the anodized Ti-30Ta-xZr alloys was higher than that of the untreated Ti alloys, indicating a better protective effect.     

The practical limits for enhancing magnetic property combinations for bulk nanocrystalline NdFeB alloys through Pr,Co and Dy substitutions

Pr, Co and Dy additions have been employed to improve the combinations of magnetic properties for nanocrystalline Nd_xFe_94−xB₆ melt spun alloys. The dependences of the magnetic properties on the solute element concentrations have been extensively investigated and the relationships between the measured remanence, maximum energy product (BH)_max and intrinsic coercivity for several compositional series are discussed. The composition ranges for these elemental substitutions which can be used to achieve the highest values of (BH)_max are identified. It is found that, when we employ individual or combined substitutions of Pr and Dy for Nd and Co for Fe in NdFeB alloys with various RE:Fe ratios, the practical limit of (BH)_max lies in the range ∼160–180 kJ/m³, combined with a coercivity in the range ∼400–800 kA/m.     

Electromagnetic wave-absorption properties of rapidly quenched of Nd–Fe–B nanocomposites with low Nd content

The electromagnetic wave-absorption properties of Nd₃Fe_68−xMn_xCo₁₈B₁₁ (x=0, 1, 2) alloys obtained by rapid quenching from the melt was studied. The complex permittivity-frequency and permeability-frequency properties were determined in the microwave frequency regime of 2–18 GHz by vector network analysis. XRD spectra showed that only α-Fe diffraction peak was observed in the as-spun alloys. It is found that the acquired complex permittivity and permeability values match the microwave frequency when the 1 at% Mn content was doped. A minimum reflection loss of −6.9 dB is obtained at 2.7 GHz for composite Nd₃Fe₆₆Mn₂Co₁₈B₁₁ with absorber thickness of 1.5 mm. The exchange interaction was attributed to the microwave absorption properties. The results suggest a new design of microwave absorbers based on electromagnetic wave-absorbing materials.     

Magnetic properties of metastable Gd-Cr alloys

We report on the magnetization, magnetocaloric effect, magnetic ordering temperatures, saturation magnetic moments and anisotropy of sputter-deposited Gd_xCr_1−x alloys with Gd atomic concentrations, x, ranging from 0.13 to 0.52. The complex magnetic nature of the Gd-Cr films was revealed from the M×H isotherms, which do not show saturation even at an applied field of 70 kOe and a temperature of 2 K and do not exhibit a linear behavior at higher temperatures. For some of the samples, the isotherms were used to determine the isothermal entropy variation as a function of temperature, for a change of 50 kOe in the applied magnetic field. The saturation magnetic moment varies with x and follows the dilution law, implying that the Cr atoms do not contribute to the total moment of the Gd-Cr alloys. Both static magnetization and dynamic susceptibility measurements reveal the existence of a magnetic glassy behavior in the alloys, which occurs below a freezing temperature. The existence of anisotropy at low temperatures for all samples was revealed by their M×H hysteresis loops from which the in-plane coercive fields, H_c, were determined. A monotonical increase in H_c with increasing Gd concentration was observed.     

Temperature dependence of magnetic anisotropy in nanoparticles of CoxFe(3−x)O4

In this paper we present a study of the magnetic anisotropy constant of nanocrystalline magnetic particles of Co_xFe_(3−x)O₄, with x ranging from 0.05 to 1.6, synthesized by a combustion reaction. The magnetic anisotropy constants were obtained by fitting the high-field part of the major hysteresis loops with the law of approach equation down to temperatures of 4 K and up to fields of 60 kOe. The anisotropy constant depends strongly on both temperature and cobalt content x, exhibiting a nonmonotic dome-shaped dependence on x with a maximum at x=1.0. We found that fits at lower temperatures, i.e., 4 and 72 K, give values of K₁ that are approximately one order of magnitude higher than those at higher temperatures, i.e., 272 and 340 K. For example, K₁ for specimens with x=0.8 and 1.0 are 4.21×10⁷ and 4.22×10⁷ ergs/cm³ at 4 K, and 7.64×10⁶ and 7.51×10⁶ ergs/cm³ at 340 K, respectively. Thus, our determination of temperature-dependence of the anisotropy constant represents an improvement over existing works.     

Structures, magnetic properties, and magnetocaloric effect in MnCo1−xGe (0.02?x?0.2) compounds

The crystalline structures, magnetic properties and magnetocaloric effect (MCE) of MnCo_1−xGe alloys (0.02?x?0.2) have been reported. The crystalline structures of MnCo_1−xGe (x?0.06) alloys are mainly of TiNiSi-type phase, and Ni₂In-type structure dominates for x>0.06. With decreasing Co concentrations the saturated magnetization of these compounds decreases. Large low-field magnetic entropy change −ΔS_M of about 2.3 J/kg K in MnCo_0.94Ge alloy has been obtained for a magnetic field change of 1 T. Moreover, it is found that TiNiSi-type phase exhibits larger −ΔS_M than Ni₂In-type one. For MnCo_0.94Ge alloy, considerable low-field refrigerant capacity (RC) (∼460 mJ/cm³), low coercivity and easy synthesis make these alloys potential candidates for near-room temperature magnetic refrigerants.     

Magnetic domain structure in Fe78.8−xCoxCu0.6Nb2.6Si9B9 nanocrystalline alloys studied by Lorentz microscopy

The magnetic domain structures of Fe_78.8−xCo_xCu_0.6Nb_2.6Si₉B₉ (x=0, 20, 40, 60) alloys are investigated by Lorentz microscopy coupled with the focused ion beam method. The specimen prepared using the FIB method is found to have a considerably more uniform thickness compared to that prepared using the ion-milling method. In Fe_38.8Co₄₀Cu_0.6Nb_2.6Si₉B₉ and Fe_18.8Co₆₀Cu_0.6Nb_2.6Si₉B₉ alloys, 180° domain walls extending in the direction of the induced magnetic anisotropy are observed. Analysis with Lorentz microscopy reveals that the width of the magnetic domains decreases with an increase in the cobalt content or the induced magnetic anisotropy K_u, that is, the domain width d is proportional to the induced magnetic anisotropy (K_u)^−1/4. On the other hand, in the in situ Lorentz microscopy observation as a function of temperature, magnetic ripple structures are found to appear in a localized area due to the fluctuation of magnetization vectors from 423 K. It is observed that the induced magnetic anisotropy caused by the applied magnetic field at 803 K is not suppressed by the magnetic ripple structures observed at 423–443 K.     

Magnetism of the Tb2Fe14−xCoxB system

The Tb₂Fe_14−xCo_xB materials were synthesized for the entire composition range (x = 0–14) and studied by X-ray and magnetometry methods. All materials have a tetragonal crystal structure with decreasing lattice parameters upon Co substitution. The Curie temperature markedly rises for alloys with low Co content. Saturation magnetization at 77 K reaches a slight maximum around x ≈ 1 and gradually decreases for higher Co concentrations. An antiparallel coupling of 3d and Tb magnetic moments is inferred from saturation magnetization data. Anisotropy fields exhibit a maximum at low Co contents, but they decrease rapidly for x > 5. A spin reorientation (axis-to-plane) occurs at high temperature in materials with x ⩾ 12.5 due to competing effects of the terbium sublattice anisotropy and the 3d sublattice anisotropy. The spin-reorientation temperature becomes lower for alloys with higher Co content. The observed magnetic behavior is discussed in terms of preferential Co substitution into 16 k₂ sites and changes in the 3d sublattice due to Co introduction. A magnetic phase diagram is constructed for the Tb₂Fe_14-xCo_xB system and compared with that of Pr₂Fe_14-xCo_xB and Nd₂Fe_{14 -x}Co_xB systems.     

Magnetocaloric effect at room temperature in manganese perovskite La0.65Nd0.05Pb0.3MnO3 with double resistivity peaks

Series of polycrystalline manganese perovskite oxides La_0.7−xNd_xPb_0.3MnO₃ (x=0, 0.05, and 0.1) are prepared by the sol-gel technique, La_0.65Nd_0.05Pb_0.3MnO₃ were representatively investigated because the peculiar double resistivity peaks were found; the maximum magnetic entropy change ΔS_H=−2.03 J/kg K and its good refrigerant capacity 71.05 J/kg around room temperature were obtained under 9 kOe magnetic field variation. The expected double peaks of magnetocaloric effect had not occurred since magnetic entropy change originated from the differential coefficient of magnetic moment to temperature; the relatively well refrigerant capacity possibly results from the faint magnetic inhomogeneity mixed in the double exchange strong magnetic signal.     

Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.     

The magnetic map of NiMn alloy thin films on Co(0 0 1) and Co(1 1 1)

Following the experimental work of Groudeva-Zotova et al. [S. Groudeva-Zotova, D. Elefant, R. Kaltofen, D. Tietjen, J. Thomas, V. Hoffmann, C.M. Schneider, J. Magn. Magn. Mater. 263 (2003) 57] where the magnetic and structural characteristics of a bi-layer NiMn-Co exchange biasing systems was investigated, density functional calculations with generalized gradient corrections were performed on (Mn_0.5Ni_0.5)_n ordered alloy on Co(0 0 1) and one Mn_1−xNi_x monolayer on Co(1 1 1). For the Mn_0.5Ni_0.5 monolayer on Co(0 0 1), magnetic moments per surface atom of 0.65 μ_B and 3.76 μ_B were obtained for Ni and Mn, respectively. Those magnetic moments are aligned parallel to the total moment of Co(0 0 1). A complex behavior of the Mn moment in dependence of the thickness “n” is obtained for (Mn_0.5Ni_0.5)_n on Co(0 0 1). Investigations on Mn_1−xNi_x monolayer on Co(1 1 1) have shown that the crystallographic orientation does not modify significantly neither the magnetic moments of Mn and Ni atoms nor their ferromagnetic coupling with the Co(1 1 1) substrate, except for x = 0.66. For x = 0.66 the Mn sub-lattice presents an antiferromagnetic coupling leading to a quenching of the Ni magnetic moment.     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.