Structural,magnetic and electrical properties of Co1−xZnxFe2O4 synthesized by co-precipitation method

Nanoparticles of Co_1−xZn_xFe₂O₄ with stoichiometric proportion (x) varying from 0.0 to 0.6 were prepared by the chemical co-precipitation method. The samples were sintered at 600 °C for 2 h and were characterized by X-ray diffraction (XRD), low field AC magnetic susceptibility, DC electrical resistivity and dielectric constant measurements. From the analysis of XRD patterns, the nanocrystalline ferrite had been obtained at pH=12.5–13 and reaction time of 45 min. The particle size was calculated from the most intense peak (3 1 1) using the Scherrer formula. The size of precipitated particles lies within the range 12–16 nm, obtained at reaction temperature of 70 °C. The Curie temperature was obtained from AC magnetic susceptibility measurements in the range 77–850 K. It is observed that Curie temperature decreases with the increase of Zn concentration. DC electrical resistivity measurements were carried out by two-probe method from 370 to 580 K. Temperature-dependent DC electrical resistivity decreases with increase in temperature ensuring the semiconductor nature of the samples. DC electrical resistivity results are discussed in terms of polaron hopping model. Activation energy calculated from the DC electrical resistivity versus temperature for all the samples ranges from 0.658 to 0.849 eV. The drift mobility increases by increasing temperature due to decrease in DC electrical resisitivity. The dielectric constants are studied as a function of frequency in the range 100 Hz–1 MHz at room temperature. The dielectric constant decreases with increasing frequency for all the samples and follow the Maxwell–Wagner's interfacial polarization.     

Effect of Zn substitution for Co on the transport properties of Y BaCo4O7

Electrical resistivity and Seebeck coefficients of Y BaCo_4−xZn_xO₇ (x=0.0,0.5,1.0,2.0) were investigated in the temperature range 350-1000 K. It was found that the electrical resistivity and activation energy increase with increasing Zn concentration, while Seebeck coefficients do not increase but decrease when electrical resistivity increases. We explained the increase of electrical resistivity and the drop of Seebeck coefficients for Zn-substituted samples by the decrease of carrier mobility, rather than of carrier concentration. The effect of oxygen absorption and desorption on the electrical resistivity and Seebeck coefficients was also investigated. An abrupt change of transport properties happens at about 650 K for x=0.0 and 0.5 samples measured in oxygen. For x=1.0 and 2.0 samples, however, such change disappears and the transport behavior in oxygen is almost same as that in nitrogen due to the significant suppression of oxygen diffusion caused by the higher Zn concentration in these samples.     

Electrical and switching properties of NiAlxFe2−xO4 ferrites synthesized by chemical method

Nickel-aluminum ferrite system NiAl_xFe_2−xO₄ has been synthesized by wet chemical co-precipitation method. The samples were studied by means of X-ray diffraction, d.c. electrical resistivity, a.c. electrical resistivity, a.c. conductivity and switching properties. The XRD patterns confirm the cubic spinel structure for all the synthesized samples. The crystallite size calculated from XRD data which confirm the nano-size dimension of the prepared samples. Electrical properties such as a.c. and d.c. resistivities as function of temperature were studied for various Al substitution in nickel ferrite. The dielectric constant and dielectric loss tangent were also studied as a function of frequency. The dielectric constant follows the Maxwell-Wagner interfacial polarization. A.C. conductivity increases with increase in applied frequency. The d.c. resistivity decreases as temperature increases, which indicate that the sample have semi-conducting nature. Verwey hoping mechanism explains the observed variation in resistivity. The activation energy is derived from the temperature variation of resistivity. Electrical switching properties were studied as I-V measurements. The current controlled negative resistance type switching is observed in all the samples. The Al substitution in nickel ferrite decreases the required switching field.     

Structural, ferroelectric and impedance spectroscopy properties of Y modified Pb(Fe0.5Nb0.5)O3 ceramics

Some ceramic samples of Pb_1−xY_x(Fe_0.5Nb_0.5)_1−x/4O₃ (PYFN) (0.00≤x≤0.08) were synthesized by a mixed oxide route. X-ray diffraction patterns of all the above samples confirm the formation of single phase material crystallizing in monoclinic structure. Dielectric properties (ε_r and tan δ) were analyzed in a wide temperature (30-350 °C) and frequency range (100 Hz-1 MHz). Ferroelectric properties of these compounds were confirmed from polarization (P-E hysteresis loop) measurements at room temperature. All the room temperature hysteresis loops of PYFN ceramics were well simulated using the ferroelectric capacitor model. Yttrium substitution resulted in notable enlargement of room temperature remnant polarization (2P_r). The 2P_r of PYFN (x=0.02) reaches to a large value (23 μC/cm²), which is nearly 5 times greater than that of PFN ceramic (4.6 μC/cm²). All the compounds exhibits negative temperature coefficient of resistivity (NTCR) type behavior as that of semiconductors. Dc conductivity (estimated via bulk resistivity) variation with temperature of all the samples follows Arrhenius type of electrical conductivity.     

Electrical properties and spin fluctuations studies of Y(Co1−xNix)2 compounds

Synthesis by arc melting, the structural and the electric properties of Y(Co_1−xNi_x)₂ alloys were studied by X-ray diffraction (XRD) and four probe dc electrical measurements. XRD analysis (300 K) shows that all samples crystallize in a cubic MgCu₂-type structure. The lattice parameters linearly decrease with Ni content. Electrical resistivity for the Y(Co_1−xNi_x)₂ intermetallic series was measured in a temperature range of 15-1100 K. The parameters involved in the dependence of resistivity on temperature were determined. Residual, phonon and spin fluctuations resistivity were separated from electrical resistivity using both the Matthiesen formula and the Bloch-Gruneisen formula. The spin fluctuations resistivity of the Y(Co_1−xNi_x)₂ series are compared to the mean square amplitudes of spin fluctuations previously calculated by the Linear Muffin Tin Orbital-Tight Binding Approach method for these series in the literature. The contribution of spin fluctuations to total resistivity ρ_sf is proportional to T² at low temperatures. The proportionality parameter strongly reduces across the Y(Co_1−xNi_x)₂ series.     

Effects of nonmagnetic silver Ag doping on the structural, magnetic and electric properties in La0.67Pb0.33MnO3 manganese oxides

The influence of the silver Ag-substitution for Pb ions in the mixed valence perovskites La_0.67Pb_0.33−xAg_xMnO₃ (0≤x≤0.15) was investigated by X-ray magnetic and electric transport measurements. All compositions were synthesized using the sol-gel technique. X-ray diffraction and structure refinement show that they crystallize in the rhombohedral structure with the R3?c space group. Upon Ag doping on Pb sites, the lattice parameters, unit cell volume, and the Mn-O-Mn bond angle are reduced. All the samples exhibit a ferromagnetic-paramagnetic transition and metallic-semi-conductor one with increasing temperature. The substitution of Pb by Ag has great influence on the magnetic and electrical transport properties of this family of compounds, decreasing continuously both the Curie temperature (from 361 to 290 K) and the resistivity transition temperature T_p.     

Study of structural, transport and magneto-resistive properties of La0.7Ca0.3−xCexMnO3 (0≤x≤0.2)

We have synthesized a series of La_0.7(Ca_0.3−xCe_x)MnO₃ (0≤x≤0.2) by standard solid-state reaction method. X-ray diffraction (XRD) measurement was carried out for structural studies and Rietveld refinement was done for structural analysis. The transport properties were studied using four probe technique. The temperature dependence of the resistivity was measured in the temperature range of 20 K to room temperature. It is found that all samples show a systematic variation in metal to insulator transition at transition temperature (T_P) and resistivity (ρ) with the relative concentration of hole and electron doping in the system. The samples showed varying amounts of colossal magnetoresistance depending upon temperature and applied magnetic field. The magnetoresistance values as high as 72% were observed in x=0 sample.     

Large enhancement of room temperature magnetoresistance in Ag-added La0.67(Ca0.65Ba0.35)0.33MnO3

The electrical and magnetoresistant properties of La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃/Ag_x (abbreviated by LCBMO/Ag_x) have been studied. The results show that Ag addition causes a decrease of resistivity dramatically and especially induces a large enhancement of room temperature magnetoresistance (MR). The room temperature MR ratio for x=0.27 sample in 10 kOe magnetic field is 41%, almost 20 times larger than that for x=0 sample. This enhancement is related to that the Curie temperature (T_c) of the sample is near room temperature, as well as the significant reduction of resistivity. The good fits of experimental results for x=0.27 sample to Brillouin function indicate that the MR behavior in the Ag added LCBMO is induced by the spin-dependent hopping of the electrons between the spin clusters, which is an intrinsic property of the CMR materials.     

The influence of Cr-content on curie temperature,crystallization temperature and room temperature electrical resistivity of Fe85−xCrxB15 metallic glasses

Amorphous ribbons of nominal compositions Fe_85-xCr_xB₁₅,_x =5, 10, 15 and 20 at%, were produced by a continuous liquid quenching technique. The Curie temperatures were measured using several methods. A quite large decrease with increasing Cr-content is observed: 20 K/at% Cr around 300 K. The Curie temperatures are compared with those of similar metallic glass systems based on Fe and Cr reported in the literature. The crystallization temperatures determined from measurements of the electrical resistivity versus temperature at a heating rate of ≈10K/min are obtained as a function of Cr-content, showing an increase in stability between 10 and 15 at% Cr. Finally, the room temperature (≈295K) electrical resistivities of as quenched and crystallized samples are given. The resistivity of the as quenched ribbons in nearly independent of Cr-content (≈128 μΩ cm) while the resistivity of the crystallized ribbons show an increase of ≈2.7 μΩ cm/at% Cr.     

Impact of Bi2O3 addition on the normal state properties of Bi3.4Pb0.3Sr2Ca1.3−x RExCu2Oy ceramics

The impact of Bi₂O₃ addition on the structural, microhardness (Vickers microhardness (VHN)), resistivity and Hall coefficient measurements of Bi_3.4Pb_0.3Sr₂Ca_1.3−x RE_xCu₂O_y ceramic samples with various x and RE is investigated. X-ray diffraction results indicate that all the peaks belong to Bi: 2212 and 2201 phases. The moderate amount of 2212 phase exists as a major phase, while the 2201 phase as a minor. The net intensity of all peaks I_max for 2212 phase increases with Y as compared to undoped sample, followed by a gradual decrease with further increase in rare earth (RE) up to La. While the vice versa is recorded for both 2201 phase and VHN. Except Y sample, a good link between flake-type grains is observed in the SEM photographs of the considered samples. The electrical resistivity turns from quiet metallic for undoped sample to semiconducting behavior for all substituted samples without any transition to the superconducting state. The Hall coefficient sign is found to be positive for undoped and Y samples and it changed from positive to negative for the other RE-substituted samples. The possible reasons for superconductivity quenching by RE substitution in this type of ceramic materials are reported.     

Physical, electrical and dielectric properties of Ca-substituted strontium hexaferrite (SrFe12O19) nanoparticles synthesized by co-precipitation method

Calcium substituted strontium hexaferrite Ca_xSr_1−xFe₁₂O₁₉ (x=0.0−0.6) nanoparticles are synthesized by chemical co-precipitation method. The synthesized samples are characterized by Fourier Transform Infrared (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopy, Transmission Electron Microscopy, DC electrical resistivity and dielectric measurements. FTIR data of uncalcined sample shows that nitrate ions are present which disappeared on calcination at 920 °C. The XRD data shows that a single hexagonal magnetoplumbite phase is formed in samples in which the calcium content, x, is ≤0.20. However, a nonmagnetic phase (α-Fe₂O₃) in addition to the hexagonal phase is also present in samples with x>0.20. The average crystallite size is found between 17 and 29 nm. The DC electrical resistivity increases with increase of calcium content up to level of x=0.2 but decreased on further addition of calcium. The enhanced resistivity of the calcium doped material has potential applications in microwave devices. The variations of dielectric constant and dielectric loss angle are explained on the basis of Maxwell-Wagner and Koops models.     

Structural,thermal and electrical properties of the semiconductor system Ag(1−x)CuxInSe2

This paper presents a study of bulk samples synthesized of the Ag_1−xCu_xInSe₂ semiconductor system. Structural, thermal and electrical properties, as a function of the nominal composition (Cu content) x=0.0, 0.2, 0.4, 0.6, 0.8, and 1.0 were studied. The influence of x on parameters such as melting temperature, solid phase transition temperature, lattice parameters, bond lengths, crystallite size t (coherent domain), electrical resistivity, electrical mobility and majority carrier concentration was analyzed. The electrical parameters are analyzed at room temperature. In general, it is observed that the properties of the Ag_1−xCu_xInSe₂ system for x≤0.4 are dominated by n-AgInSe₂, while for x>0.4, these are in the domain of p-CuInSe₂. The crystallite size t in the whole composition range (x) is of the order of the nanoparticles. Secondary phases (CuSe, Ag₂Se and InSe) in small proportion were identified by XRD and DTA.     

Electron transport properties of Co71−xFexCr7Si8B14 (x=0, 2, 3.2, 4, 6,8 and 12 at%) amorphous alloys during devitrification

The investigation addresses the electron transport properties of Co_71−xFe_xCr₇Si₈B₁₄ (x=0, 2, 3.2, 4, 6, 8 and 12 at%) amorphous alloys. The variation in electrical resistivity of as-cast amorphous materials with thermal scanning from room temperature to 1000 K was measured. The CoFe-based alloys revealed an initial decrease in temperature coefficient of resistivity (TCR), a characteristic of spin-wave phenomena in glassy metallic systems. This behaviour in the present alloys was in a sharp contrast to the Co-based amorphous materials that indicate the drop in resistivity much below room temperature. In the studied alloys, the variation in initial TCR values and the full-width at half-maxima determined from X-ray diffraction of as-quenched materials exhibited a similar trend with increasing Fe content, indicating the compositional effect of near neighbouring atoms. After the initial decrease in resistivity, all the alloys indicated a subsequent increase at T_min. The Curie temperature (T_C), which was measured from thermal variation of ac susceptibility showed non-monotonic change with Fe content. In the temperature range between T_min and T_C the relative scattering by electron-magnon and electron-phonon resulted in the non-monotonic change in Curie temperature. At crystallization onset (T_X1) all the alloys except there with X=6, showed a sharp decrease in electrical resistivity which was attributed to ordering phenomena. In contrast to this resistivity decrease, X=6 alloy exhibited a drastic increase in resistivity around T_X1 observed during amorphous to nanocrystalline transformation. Such nanocrystalline state was observed by Transmission electron microscopy.     

ESR investigation of the spin dynamics in (Gd1−xYx)2PdSi3

We report electron-spin resonance (ESR) measurements in polycrystalline samples of (Gd_1−xY_x)₂PdSi₃. We observe the onset of a broadening of the linewidth and of a decrease of the resonance field at approximately twice the Néel temperature in the paramagnetic state. This characteristic temperature coincides with the electrical resistivity minimum. The high-temperature behavior of the linewidth is governed by a strong bottleneck effect.     

Oxygen vacancy doping effect on the electrical and magnetic behavior of Ba5−xLaxNb4−xTixO15

We report electric and magnetic properties of oxygen deficient Ba_5−xLa_xNb_4−xTi_xO_15−δ phases, which have been prepared by solid-state reaction method followed by a controlled reduction process under hydrogen atmosphere. The extra electrons added by the formation of the oxygen vacancies (δ) introduce localized spins and the magnetic susceptibility can be described by a temperature-independent contribution and a Curie-Weiss term associated to the Ti³⁺ ion formation. Besides, the experimental resistivity (ρ) data of these four reduced compounds are well described in a wide temperature range with the equation , which suggests the presence of small polarons in the system. Although, all samples present electrical insulating behavior, the electrical resistivity decreases four orders of magnitude for intermediate x values. We interpreted this fact as a consequence of the mix between the localized bands of the Nb and Ti ions, which favors the promotion of carriers due to reduction of the band gap.     

Anomalous variation of magnetoresistance in Nd0.67−yEuySr0.33MnO3 manganites

A systematic investigation of Eu-doped Nd-based colossal magnetoresistive manganites with compositional formula Nd_0.67−yEu_ySr_0.33MnO₃(y=0-0.67) has been undertaken to understand their structural, magnetic as well as electrical behavior. These materials were prepared by the citrate gel route, and were later characterized by X-ray diffraction (XRD), AC susceptibility, electrical resistivity etc; measurements. A detailed structural characterization of the XRD data has also been undertaken, using Rietveld refinement method. From a systematic analysis of electrical resistivity versus temperature data, it has been found that the last two samples of the series (y=0.57 and 0.67) are found to exhibit charge order (CO) phenomenona, and that the CO state melts completely in the case of former sample (y=0.57) while it melts partially only in the case of later one (y=0.67), even in a magnetic field of 7 T. The observed behavior has been explained qualitatively. Some of the samples of the series are found to exhibit unusually large magnetoresistance over a wide temperature range in the low temperature region, and their behavior has been explained on the basis of phase segregation and an inter-grain spin polarized tunneling effect.     

Electrical resistivity of narrow-band ferromagnetic Fe1−xCoxS2

The electrical resistivity of metallic ferromagnet Fe_1−xCo_xS₂ shows an anomalous temperature dependence below Curie point. As the temperature lowers, the resistivity increases for x < 0.9, while it decreases for x > 0.9 with a hump.     

Electrical conductivity and low field magnetoresistance in polycrystalline La1−xKxMnO3 pellets prepared by pyrophoric method

Electrical conductivity and magnetoresistance of a series of monovalent (K) doped La_1−xK_xMnO₃ polycrystalline pellets prepared by pyrophoric method have been reported. K doping increases the conductivity as well as the Curie temperature (T_C) of the system. Curie temperature increases from 260 to 309 K with increasing K content. Above the metal-insulator transition temperature (T>T_MI), the electrical resistivity is dominated by adiabatic polaronic model, while in the ferromagnetic region (50<T<T_MI), the resistivity is governed by several electron scattering processes. Based on a scenario that the doped manganites consist of phase separated ferromagnetic metallic and paramagnetic insulating regions, all the features of the temperature variation of the resistivity between ∼50 and 300 K are described very well by a single expression. All the K doped samples clearly display the existence of strongly field dependent resistivity minimum close to ∼30 K. Charge carrier tunneling between antiferromagnetically coupled grains explains fairly well the resistivity minimum in monovalent (K) doped lanthanum manganites. Field dependence of magnetoresistance at various temperatures below T_C is accounted fairly well by a phenomenological model based on spin polarized tunneling at the grain boundaries. The contributions from the intrinsic part arising from DE mechanism, as well as, the part originating from intergrannular spin polarized tunneling are also estimated.     

Magnetotransport and magnetoelastic effects in Co-doped La0.7Sr0.3MnO3 nanocrystalline perovskites

La_0.7Sr_0.3Mn_1−xCo_xO₃ (x=0, 0.05, 0.1) nanoparticles, prepared by sol-gel method, were studied by means of X-ray diffraction, transmission electron microscopy, resistivity, magnetoresistance, thermal expansion and magnetostriction measurements. Results show that partial substitution of Mn by Co leads to a reduction in lattice parameters, enhancement of resistivity and room temperature magnetoresistance MR, decrease of metal-insulator transition temperature T_MI and T_C, an increase in thermal expansion coefficient, volume magnetostriction and anisotropic magnetostriction. The latter increases about one order of magnitude with 10% Co substitution. In comparison with Mn ions, the Co ions possess higher anisotropy energy, larger magnetostriction effect, smaller ionic size and spin state transitions with increase in temperature and magnetic field; this suggests that Co substitution leads to double-exchange interaction weakening, resulting in suppression of ferromagnetic long-range order and metallic state and increase of magnetic anisotropy. Furthermore, our samples have a relatively lower T_MI and T_C, higher resistivity and MR, compared with the reported values for similar compounds with larger particle sizes. This is attributed to the nanometric grain size and spin-polarized tunneling between neighboring grains.     

Structure, magnetic, and transport properties of the Co-doped manganites La0.9Te0.1Mn1−xCoxO3 (0≤x≤0.25)

The effect of Co doping at Mn-site on the structural, magnetic and electrical transport properties in electron-doped manganties La_0.9Te_0.1Mn_1−xCoxO₃ (0≤x≤0.25) has been investigated. The room temperature structural transition from rhombohedra to orthorhombic (Pbnm) symmetry is found in these samples with x≥0.20 by the Rietveld refinement of X-ray powder diffraction patterns. All samples undergo the paramagnetic-ferromagnetic (PM-FM) phase transition. The Curie temperature T_C of these samples decreases and the transition becomes broader with increasing Co-doping level. The magnetization magnitude of Co-doping samples increases at low temperatures with increasing Co-doping level for x≤0.15 and decreases with increasing Co-doping content further. The metal-insulator (M-I) transitions observed in the sample with x=0 are completely suppressed with Co doping, and the resistivity displays semiconducting behavior within the measured temperature region for these samples with x>0. All results are discussed according to the changes of the structure parameters and magnetic exchange interaction caused by Co-doping. In addition, the different effects between the Co doping and Cu doping in the Mn site for the electron-doped manganites are also discussed.