Electronic, structural and magnetic phase diagram of Sm1-xSrxMnO3 manganites

The electronic, structural and magnetic phase diagram of the colossal magnetoresistive Sm_1−xSr_xMnO₃ (0.16≤х≤0.67) manganites is constructed on the basis of their systematic studies by high-resolution neutron powder diffraction. It is shown the tendency of researched system to formation of the phase-separated states on crystallographic as well as, in the even greater extent, on magnetic level. A clear correlation between fine specific features and temperature evolution of crystal structures, spin ordering of the manganese ions, and the physical properties of the samarium-strontium series of manganites obtained from temperature magnetic and transport measurements is demonstrated. It was found that ground state of Sm-Sr manganites shows very various physical properties depending first of all on the doping level х and, for given х, determined by two distortion parameters, namely, the average A-cation size <r_A> and the local A-cation size mismatch σ².     

Structural phase transitions at high-temperature in double perovskite Sr2GdRuO6

The crystal structure evolution of the Sr₂GdRuO₆ complex perovskite at high-temperature has been investigated over a wide temperature range between 298 K≤T≤1273 K. Powder X-ray diffraction measurements at room temperature and Rietveld analysis show that this compounds crystallizes in a monoclinic perovskite-type structure with P2₁/n (#14) space group and the 1:1 ordered arrangement of Ru⁵⁺ and Gd³⁺ cations over the six-coordinate M sites, with lattice parameters a=5.81032(8) Å, b=5.82341(4) Å, c=8.21939(7) Å, V=278.11(6) Å³ and angle β=90.311(2)^o. The high-temperature analysis shows that this material suffers two-phase transitions. At 373 K it adopts a monoclinic perovskite structure with I2/m space group, and lattice parameters a=5.81383(2) Å, b=5.82526(4) Å, c=8.22486(1) Å, V=278.56(2) Å³ and angle β=90.28(2)^o. Above of 773 K, it suffers a phase transition from monoclinic I2/m to tetragonal I4/m, with lattice parameters a=5.84779(1) Å, c=8.27261(1) Å, V=282.89(5) Å³ and angle β=90.02(9)^o. The high-temperature phase transition from monoclinic I2/m to tetragonal I4/m is characterized by strongly anisotropic displacements of the anions.     

Synthesis and characterization of Co7(OH)12(C2H4S2O6)(H2O)2—a single crystal structural study of a ferrimagnetic layered cobalt hydroxide

A novel layered hydrotalcite-like material, Co₇(H₂O)₂(OH)₁₂(C₂H₄S₂O₆), has been prepared hydrothermally and the structure determined using single crystal X-ray diffraction (a=6.2752(19) Å, b=8.361(3) Å, c=9.642(3) Å, α=96.613(5)°, β=98.230(5)°, γ=100.673(5)°, R1=0.0551). The structure consists of brucite-like sheets where 1/6 of the octahedral sites are replaced by two tetrahedrally coordinated Co(II) above and below the plane of the layer. Ethanedisulfonate anions occupy the space between layers and provide charge balance for the positively charged layers. The compound is ferrimagnetic, with a Curie temperature of 33 K, Curie-Weiss θ of −31 K, and a coercive field of 881 Oe at 5 K.     

Synthesis of hexagonal C14/C36 and cubic C15 ZrCr2 Laves phases and thermodynamic stability of their hydrides

ZrCr₂ samples with well defined hexagonal (C14/C36) or cubic (C15) Laves phase structures have been synthesised by melting in an arc furnace followed by different treatments depending on the sample type. Hydrogen absorption capacity and thermodynamic stability of their respective hydrides have been investigated by solid–gas reaction. Pressure–composition–temperature (PCT) curves obtained for both structures at temperatures of 348, 373, 398 and 423 K, and H-pressures from 10¹ to 10⁶ Pa, showed that the cubic phase is less stable than the hexagonal ones. This result was related to Miedema's rule of reversed stability and also correlated to the volume of the interstitial hole for hydrogen.     

Crystal structure and magnetic properties of TbFe0.4Ge2 compound

Neutron diffraction and magnetic measurements were performed on polycrystalline TbFe_0.4Ge₂ which crystallizes with the orthorhombic structure of the CeNiSi₂-type. Despite the presence of some clear anomalies in the low-temperature magnetic susceptibility, the neutron diffraction experiment did not reveal any long-range magnetic ordering of the Tb magnetic moments down to 1.57 K.     

Room temperature stable structures and phase transition of Na2Al2B2O7

By Rietveld refinement of the X-ray diffraction (XRD) data of powdered Na₂Al₂B₂O₇ samples aged for over 3 months, we found that Na₂Al₂B₂O₇ at room temperature is a mixture of two phases with space group and P6₃/m, respectively. The structures of the two phases can be refined with identical cell parameters of a=4.80760(11) Å, c=15.2684(5) Å and are composed by [Al₂B₂O₇]²⁻_∝ double layers stacking alternatively with Na⁺ ions along the c-direction, but differ at in-plane bond orientations of the BO₃/AlO₄ groups within the double layers: in P6₃/m phase B-O₁/Al-O₁ bonds of the two layers are perfectly aligned, whereas in phase they are twisted by 46.4/41.6° around c-axis against each other. It is also found that a freshly prepared sample contains only the phase, but part of the phase will transfer to P6₃/m phase slowly at room temperature and the transition can be reversed by heating the aged sample above 220 °C.     

Effects of high Fe substitution for Mn on phase transition and magnetic properties of YFexMn12−x compounds

YFe_xMn_12−x (x=7-10) compounds were synthesized; their structure and magnetic properties were investigated, the results reveal that a higher Fe concentration x makes the crystal phase change from ThMn₁₂-type to Th₂Zn₁₇-type, with the phase transition point x=9; the Curie temperature increases with increasing x, which becomes 290 K for x=8.8 and 150 K for x=7; and the magnetization also increases monotonically with increasing x until the phase transition point.     

Effect of Gd doping on structural, electrical and magnetic properties of BiFeO3 electroceramic

Room temperature multiferroic electroceramics of Gd doped BiFeO₃ monophasic materials have been synthesized adopting a slow step sintering schedule. Incorporation of Gd nucleates the development of orthorhombic grain growth habit without the appearance of any significant impurity phases with respect to original rhombohedral (R3c) phase of un-doped BiFeO₃. It is observed that, the materials showed room temperature enhanced electric polarization as well as ferromagnetism when rare earth ions like Gd doping is critically optimized (x=0.15) in the composition formula of Bi_1+2xGd_2x/2Fe_1−2xO₃. We believe that magnetic moment of Gd⁺³ ions in Gd doped BiFeO₃ tends to align in the same direction with respect to ferromagnetic component associated with the iron sub lattice. The dielectric constant as well as loss factor shows strong dispersion at lower frequencies and the value of leakage current is greatly suppressed with the increase in concentration of x in the above composition. Addition of excess bismuth and Gd (x=0.1 and 0.15) caused structural transformation as well as compensated bismuth loss during high temperature sintering. Doping of Gd in BiFeO₃ also suppresses spiral spin modulation structure, which can change Fe-O-Fe bond angle or spin order resulting in enhanced ferromagnetic property.     

Crystal structure of Tl0.5Pb0.5Sr2Ca2Cu3O9 at 300 K and around Tc (118 K)

The crystal structure including the cation distribution, of a polycrystalline sample of nominal composition Tl_0.5Pb_0.5Sr₂Ca₂Cu₃O₉ with T_c = 118.2 K has been determined using resonant synchrotron X-ray diffraction data collected at the Cu K, Tl L_III and Sr K edges and time-of-flight powder neutron diffraction data. No oxygen deficiency was observed, but cation disorder at all the non copper sites according to the formula (Tl_0.60Pb_0.40)(Sr_1.60Ca_0.40)(Ca_1.93Tl_0.07) Cu₃O₉ gives a mean hole concentration of 0.18(1) per Cu atom for the three CuO₂ planes, consistent with the high T_c for this material. Analysis of five time-of-flight powder neutron diffraction data between 80 and 150 K have revealed a possible discontinuity in the variation of the c lattice parameter at T_c, due to an anomaly in the position of the apical oxygen atoms.     

First principles study of pressure induced structural phase transition in hydrogen storage material—MgH2

First principles calculation were performed using Vienna ab-initio simulation package within the frame work of density functional theory (DFT) to understand the electronic properties of magnesium hydride. At normal pressure, the most stable structure of MgH₂ is rutile type with a wide band gap of 3.52 eV, which agrees well with the available data. A pressure induced semi-conductor to metallic transition at a pressure of 92.54 GPa is predicted. Our results indicate a sequence of pressure induced structural phase transition in MgH₂. The obtained sequence of phase transition was α→γ→β→δ→ε at a pressure of 0.37 GPa, 3.89 GPa,7.23 GPa and 11.26 GPa, respectively. Thus our results indicate that MgH₂ is one of the best hydrogen storage material and the maximum storage capacity achieved was 7.7%.     

Antiferromagnetism of the hexagonal Laves phase ThMn2

Magnetization, thermal expansions and neutron diffraction measurements have been performed on ThMn₂. Below T_N, one Mn atom (2a) in four remains nonmagnetic whilst the others order in a triangular configuration. The large anistropic thermal expansions effects minimize the frustration of the Mn-Mn interactions.     

Crystal chemistry of layered carbide, Ti3(Si0.43Ge0.57)C2

 The crystal structure of a layered ternary carbide, Ti₃(Si_0.43Ge_0.57)C₂, was studied with single-crystal X-ray diffraction. The compound has a hexagonal symmetry with space group P6₃/mmc and unit-cell parameters a=3.0823(1) Å, c=17.7702(6) Å, and V=146.21(1) Å³. The Si and Ge atoms in the structure occupy the same crystallographic site surrounded by six Ti atoms at an average distance of 2.7219 Å, and the C atoms are octahedrally coordinated by two types of symmetrically distinct Ti atoms, with an average C-Ti distance of 2.1429 Å. The atomic displacement parameters for C and Ti are relatively isotropic, whereas those for A (=0.43Si+0.57Ge) are appreciably anisotropic, with U₁₁ (=U₂₂) being about three times greater than U₃₃. Compared to Ti₃SiC₂, the substitution of Ge for Si results in an increase in both A-Ti and C-Ti bond distances. An electron density analysis based on the refined structure shows that each A atom is bonded to 6Ti atoms as well as to its 6 nearest neighbor A site atoms, whether the site is occupied by Si or Ge, suggesting that these bond paths may be significantly involved with electron transport properties.     

High temperature structural studies of SrRhO3

High resolution X-ray powder diffraction studies have shown SrRhO₃ to transform from an orthorhombic Pnma structure at room temperature through an intermediate Imma phase to a tetragonal I4/mcm structure near 800 °C. The orthorhombic Imma phase exists over a very limited temperature range, of less than 20°. The diffraction data suggests the Pnma to Imma transition is continuous and demonstrates that the Imma-I4/mcm transition is first order.     

Influence of milling time on the structural, microstructural and magnetic properties of mechanically alloyed Ni58Fe12Zr10Hf10B10 nanostructured/amorphous powders

This paper investigates structural, microstructural and magnetic properties of amorphous/nanocrystalline Ni₅₈Fe₁₂Zr₁₀Hf₁₀B₁₀ powders prepared by high energy milling. Ball milling of Ni, Fe, Zr, Hf and B leads to alloying of the element powders at 120 h. The results show that at 190 h the amorphous content is at the highest level and the grain size is about 2 nm. The magnetic measurements reveal that the coercivity and the saturation magnetization reach about 20 Oe and 30 emu/g at 190 h and become approximately 5 Oe and 40 emu/g after a suitable heat treatment, respectively.     

Structural and magnetic ordering in the VxNb1+yS2 system

The influence of composition on the structural ordering and magnetism in the V_xNb_1+yS₂ system has been investigated by X-ray diffraction and magnetic measurements. Stoichiometric V_1/3NbS₂ did not exhibit the structural ordering of vanadium between the NbS₂ layers. In the ordered structure, the vanadium composition deviated from the ideal value of to both higher and lower values, while the niobium composition was in the range of 0.05?y?0.18. Excess niobium, y>0, is thought to play an essential role in the structural ordering in this system. For samples with excess niobium and ordered structures, a magnetic transition was observed at 20-50 K, depending on the composition. The spontaneous magnetization of 3-5×10⁻³ μ_B/V atom is thought to be intrinsic to this system. The magnetization curves consisted of a constant and a proportional parts of the magnetic field, which correspond to the spontaneous magnetization and high-field susceptibility, respectively. The magnetization curves and the temperature dependencies of the high-field susceptibility were quite similar to those of the canted antiferromagnetic NiS₂. A correlation between the structural and magnetic ordering is suggested.     

Influence of cation substitution on the magnetic properties of the FeCr2S4 ferrimagnet

The influence of cation substitution on the magnetic properties of single and polycrystals of FeCr₂S₄ spinel has been studied. The tetrahedral A-site substitution of the Fe by Cu in Fe_1−xCu_xCr₂S₄ was found to increase significantly the value of temperature T_m of the spin-glass like magnetization anomaly, whereas the octahedral B-site substitution of the Cr by In decreases T_m. This effect is suggested to result from a structural transformation influenced by variation of internal (chemical) pressure due to lattice contraction (Cu) or expansion (In). The observed reduced values of the Curie temperature for Cu-substituted single crystals compared to that of the polycrystalline samples are attributed to presence of Cl ions in samples detected by electron-probe microanalysis. The observed reduced value of saturation magnetization in the polycrystals compared to the single crystals is ascribed to the effect of surface anisotropy. Based on the experimental data the superexchange is concluded to be the dominant exchange interaction for 0≤x≤0.5 in Fe_1−xCu_xCr₂S₄, whereas the indirect exchange through the charge carriers is considered of minor importance.     

Magnetic and structural properties of iron phosphate-phenolic soft magnetic composites

This work focuses on the effect of phosphate modification on the magnetic and surface properties of iron-phenolic soft magnetic composite materials. Fourier transform infrared (FTIR) spectra, EDX analysis, distribution maps, X-ray diffraction pattern and density measurements show that the particles surface layer contains a thin layer of nanocrystalline/amorphous phosphate with high coverage of powders surface. Magnetic measurements show that phosphating treatment decreases the loss factor, imaginary part of permeability, increases the electrical resistivity and operating frequencies by decreasing the effective particle size. The operating frequency increases from 200 kHz for uncoated-powders samples to 1 MHz for phosphated-powders samples at optimum concentration. Phosphated iron powders that are covered by 0.7 wt% of phenolic resin exhibits lower magnetic loss and higher frequency stability. The minimum loss factor and maximum permeability at each frequency can be obtained for 0.01 g/ml orthophosphoric acid concentration in comparison with other concentrations including 0.005 and 0.04 g/ml.     

A variable temperature structural study of the Jahn-Teller distortion in Ba2CuUO6

The structure of the ordered double perovskite Ba₂CuUO₆ has been investigated between room temperature and 800 °C using synchrotron X-ray powder diffraction. At room temperature Ba₂CuUO₆ is tetragonal, space group I4/m, a=8.82331(13) c=8.82330(13) Å, the structure being characterized by a large Jahn-Teller distortion of the CuO₆ octahedra and small out-of-phase tilts of the BO₆ octahedra. This Jahn-Teller distortion is also evident in the UV-Vis spectra. Analysis of the spontaneous tetragonal strain reveals a continuous ferroelastic phase transition near 420 °C. This appears to be related to the loss of the tilts whilst maintaining the Jahn-Teller distortion, so that the high temperature structure is in space group I4/mmm.     

Synthesis, structural and magnetic properties of spin ladder compound Ca1−xCoxCu2O3

MCu₂O₃ (M=Ca and Co) system has two-leg spin ladder structure similar to that of the prototype SrCu₂O₃ system except that the rungs are buckled with an angle of 123° and 105° for CaCu₂O₃ and CoCu₂O₃ compounds, respectively. We have synthesized powder samples of (Ca_1−xCo_x)Cu₂O₃ (x=0.00-1.00) by the solid state reaction method and their structural and magnetic properties have been investigated. All the synthesized compounds crystallize in orthorhombic structure with space group Pmmn. Lattice parameters of (Ca_1−xCo_x)Cu₂O₃ decrease with the increase in Co content. DC magnetic susceptibility χ(T) results of the end products CaCu₂O₃ and CoCu₂O₃ show antiferromagnetic transition (T_N) at 27 and 215 K, respectively. Co doping into (Ca_1−xCo_x)Cu₂O₃ enhances its T_N systematically with increasing Co concentration. The χ(T) of CoCu₂O₃ shows a broad transition with the peak temperature around 215 K and it was found to be field independent up to 90 kOe. The ambiguity concerning the transition was ruled out by recording the temperature dependent X-ray diffraction pattern on CoCu₂O₃ system, which indicated that there is no structural transition in the investigated temperature range of 115-300 K. Further, specific heat measurement on CoCu₂O₃ confirms the magnetic phase transition by the appearance of a sharp peak at 215 K.