多重射流燃烧反应制备的TiO2/ SiO2纳米复合颗粒的形态和结构

TiO₂-SiO₂ nanocomposite particles were prepared in premixed H₂ / Air flame, and the morphology and structure of these nanocomposites were characterized by FTIR, XRD, TEM and HRTEM. The morphology of SiO₂ / TiO₂ nanocomposites was different from that of pure TiO₂ or SiO₂ nanoparticles, and the chemical bond of Ti-O-Si was found in the nanocomposites indicating that the TiO₂ / SiO₂ nanocomposites were not merely a physical mixture of TiO₂ and SiO₂. TiO₂ nanocrystalline grains with sizes of 1～2 nm were homogeneously dispersed in the amorphous SiO₂ matrix when TiCl₄ and SiCl₄ were mixed at molecular level in the flame. The particle size and rutile content decreased with increasing of SiO₂ molar ratio.     

Mechanical and fire retardant properties of EVA/clay/ATH nanocomposites - Effect of particle size and surface treatment of ATH filler

Mechanical and flame retardant properties of ethylene vinyl acetate (EVA) copolymer/organoclay/alumina trihydrate (ATH) nanocomposites have been studied. ATH with different particle sizes, ATH1 (2.2-5.2 μm) and ATH2 (1.5-3.5 μm), and three different surface treatments, uncoated, fatty acid coated and silane coated, have been used. A synergistic effect was observed in EVA/organoclay/ATH nanocomposites with the total heat evolved (THE) and the heat release rate (HRR) lower than that of EVA/ATH composite. It was also found that mechanical and flame retardant properties are affected in different ways by the particle size and the surface treatment of ATH fillers. Improvements in tensile and flame retardant properties were observed in nanocomposites when uncoated ATH fillers and fatty acid coated ATH2 filler were used. On the other hand, silane coating on ATH1 and ATH2 improves limiting oxygen index (LOI) and leads to higher t_ignition and the best char stability after cone calorimeter test.     

Structure of mono- and bimetallic heterogeneous catalysts based on noble metals obtained by means of fluid technology and metal-vapor synthesis

Monometallic nanocomposites are obtained with the use of supercritical carbon dioxide (fluid technique) and metal-vapor synthesis (MVS), while bimetallic nanocomposites of Pt and Au noble metals and ??-Al₂O₃ oxide matrix are synthesized by a combination of these two methods. The structures, concentrations, and chemical states of metal atoms in composites are studied by means of small-angle X-ray scattering (SAXS), transparent electron microscopy (TEM), X-ray fluorescent analysis (XFA), and X-ray photoelectron spectroscopy (XPS). The neutral state of metal atoms in clusters is shown by XPS and their size distribution is found according to SAXS; as is shown, it is determined by the pore sizes of the oxide matrices and lies in the range of 1 to 50 nm. The obtained composites manifest themselves as effective catalysts in the oxidation of CO to CO₂.     

In situ preparation of polyaniline coated fumed and precipitated silica fillers and their composites with nitrile rubber (Investigation on structure-property relationship)

In situ synthesis of polyaniline (PAni) coated pyrogenic or fumed silica (PCFS) and precipitated silica (PCPS) were carried out by the oxidative polymerization of aniline in presence of fumed silica (FS) and precipitated silica (PS). Both uncoated and PAni coated silica fillers were characterized through scanning electron microscope (SEM), infrared spectroscopy and thermo-gravimetric analysis (TGA) to evaluate particle morphology and physico-chemical character of coated and uncoated silica particles. Semi-conducting composites made from two different types of PAni coated silica fillers with NBR exhibit different trend in the variation of electrical properties under different temperature and pressure. These differences in electrical properties of two types of composites are mainly due to physico-chemical characteristics of filler particles as well as their distribution in the polymer matrix. This type of composites may be used as semi-conducting and ESD (electrostatic discharge) material.     

Micro structural investigations on TNT and PETN incorporated silica xerogels

Silica xerogels incorporated with trinitrotoluene (TNT) and pentaerythritoltetranitrate (PETN) were synthesized using sol–gel method. Tetramethoxysilane was used as precursor for silica. TNT and PETN content in the resulted explosive/silica xerogel was varied ranging from 50 to 90%. Infra red spectra showed that explosives were retained in the silica xerogel matrix. Transmission electron microscopy (TEM) reveal that explosives particles were uniformly distributed in xerogel matrix and the size of the PETN and TNT particles are in the range 15–18 nm. Small angle x-ray scattering showed that the sizes of the pores in the silica matrix are in the range 25–13 nm. The particles of TNT and PETN occupy the pores in the matrix resulting in gradual reduction of pore-size affecting the surface characteristics of the pore-matrix interface. Understanding of the structure of aggregates of small particles thus produced could be useful to explain the properties shown by the fine explosives. Our study suggests that particle size of explosives in the nanometer range can be achieved using the sol–gel method.     

Characterization of kaolinite/emulsion-polymerization styrene butadiene rubber (ESBR) nanocomposite prepared by latex blending method: Dynamic mechanic properties and mechanism

The latex blending method was chosen to prepare Kaolinite/emulsion-polymerization styrene butadiene rubber (ESBR) nanocomposite to improve the interaction between filler particles and rubber matrix chains. The influences of kaolinite particles size, filler contents, and flocculants types on dynamic mechanical properties and the relative reinforcement mechanism of the prepared composite were systematic investigated and proposed. The transmission electron microscopy (TEM) and scanning electron microscopy (SEM) showed that the kaolinite particles were finely dispersed into the rubber matrix and arranged in parallel orientation. The prepared nanocomposites by latex blending exhibited improved crosslinking characteristic and dynamic mechanical parameters. The KAl (SO₄)₂ flocculant presented obvious modification in dynamic properties and crosslinking characteristic. Both the decrease in kaolinite particle size and the increase in kaolinite content can greatly improve the storage modulus and reinforcing effect of kaolinite/ESBR nanocomposites. The dynamic reinforcement mechanism of kaolinite can be explained by filler network including a certain thickness of rubber shell on the surface of kaolinite lamellar structure and the aggregations network between kaolinite particles The optimum way to balance the dynamic properties of rubber nanocomposites at different temperatures is to reduce the surface difference between kaolinite and rubber matrix and the degree of filler-filler networking on the basis of kaolinite with nanoscale (nanometer effect).     

Concentrated reverse micelles in a random graft block copolymer system: structure and in-situ synthesis of silver nanoparticles

The structure and rheological properties of a poly(dimethylsiloxane)-graft-poly(oxyethylene) copolymer at high concentrations in block-selective solvents were studied by small-angle X-ray scattering (SAXS) and rheometry. Analysis of SAXS data indicates that quasispherical, reverse micellar aggregates (with no ordered packing) are present in concentrated solutions of the copolymer in nonpolar solvents, and that upon addition of water, the size of such aggregates increases due to the solubilization inside the micellar cores. The viscosity of concentrated polymer solutions increases exponentially as water is added, and finally, viscoelastic, gel-like behavior is found in the vicinity of the phase separation limit. It was found that small silver nanoparticles with an average diameter of ≈3 nm can be synthesized inside the copolymer aggregates without the need of a reducing agent; namely, particles embedded in a viscoelastic matrix are obtained. The synthesis seems to follow first-order kinetics. Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Phase morphology of iPP/aPS/SEP blends

Supermolecular structure and phase morphology of the ternary isotactic polypropylene/atactic polystyrene/poly(styrene-b-ethylene-co-propylene) (iPP/aPS/SEP) compression molded blends with 100/0, 90/10, 70/30, and 50/50 iPP/aPS weight ratios and with different amounts of added SEP compatibilizer were studied by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), small-angle X-ray scattering (SAXS) and wide-angle X-ray diffraction (WAXD). SEP significantly reduced the size of dispersed aPS particles that enabled better spherulitization in the iPP matrix. Furthermore, iPP spherulites in ternary blends with 90/10 iPP/aPS weight ratio became larger in comparison with the pure iPP. TEM revealed that the SEP formed continuous interface layer around the dispersed aPS particles even when only 2.5 wt.% of SEP was added. Particle size distribution was distinctly bimodal. When the SEP content was increased to 10 wt.%, joining together smaller and bigger aPS and SEP particles formed dispersed aggregates. Additionally, both amorphous components (aPS and SEP) influenced crystallization process of iPP matrix and so modified, to some extent, its final supermolecular structure. SEP compatibilizer did not significantly affect crystallite orientation. The increase of crystallite sizes, which was more affected by the addition of aPS than by the addition of SEP, seemed to be influenced by the solidification effect rather than by the phase morphology of the blends.     

Investigation of primary crystallite sizes in nanocrystalline ZnS powders: comparison of microwave assisted with conventional synthesis routes

ZnS powders with primary crystallite sizes of only a few nanometers were prepared by three different synthesis routes at temperatures below 130 degrees C. The reaction of zinc acetate dihydrate with thioacetamide (TAA) in the presence of pyridine and triphenylphosphite (TPP) was carried out using either conventional heating or microwave heating. The obtained powders exhibit sphalerite structure as determined by X-ray diffraction (XRD). The primary crystallites have diameters between 1 and 7 nm obtained by XRD. Small angle X-ray scattering (SAXS) measurements were analyzed by the model-free inverse Fourier-transformation approach, as well as by a hard sphere-model from which particle size and polydispersity were extracted. The particle sizes by SAXS are in good agreement with the primary crystallite sizes obtained by XRD. It has been found that an increasing amount of sulfur and/or using microwave heating increases crystallite sizes. The presence of TPP decreases the particle sizes but no significant influence on the TPP concentration was observed. In the alternative third preparation route, hexamethyldisilathiane (HMDST) was used as precipitation reagent at ambient temperature, which leads to the smallest crystallite sizes of only 1 nm together with low polydispersities. Scanning electron microscopy, dynamic light scattering and UV-vis spectroscopy showed that all three synthesis routes lead to ZnS powders with aggregate sizes between 650 and 1200 nm. Both of the TAA-precipitation routes lead to spherical agglomerates which consist of spherical substructures, whereas the HMDST agglomerates are assembled from elongated objects.     

Investigation of a catalyst ink dispersion using both ultra-small-angle X-ray scattering and cryogenic TEM

The dispersion of Nafion ionomer particles and Pt/C catalyst aggregates in liquid media was studied using both ultra-small-angle X-ray scattering (USAXS) and cryogenic TEM. A systematic approach was taken to study first the dispersion of each component (i.e., ionomer particles and Pt/C aggregates), then the combination of the components, and last the catalyst ink. Multiple-level curve fitting was used to extract the particle size, size distribution, and geometry of the Pt/C aggregates and the Nafion particles in liquid media from the scattering data. The results suggest that the particle size, size distribution, and geometry are not uniform throughout the systems but rather vary significantly. It was found that the interaction of each component (i.e., the Nafion ionomer particles and the Pt/C aggregates) occurs in the dispersion. Cryogenic TEM was used to observe the size and geometry of the particles in liquid directly and to validate the scattering results. The TEM results showed excellent agreement.     

Correction of STM tip convolution effects in particle size and distance determination of metal-C:H films

Metal containing amorphous hydrocarbon films consist of nanometer size metallic particles in a hydrogen-carbon matrix. Scanning tunneling microscopy (STM) of Au and Pt containing amorphous C:H-films was performed in order to determine particle size- and distance distributions. To correct tip convolution effects, which lead to apparent particle enlargement and particle hiding (1) a method is presented which allows off-line STM tip radius determination by statistical analysis of apparent particle radii and thereby a correct particle radii determination. (2) A simple Monte Carlo model is proposed to compute fractions of hidden particles and their influence on particle distance distributions. Results of these evaluations are compared with results from small angle X-ray scattering (SAXS), transmission electron microscopy (TEM) and X-ray diffraction (XRD).     

Gold-Nickel Hydroxide Multi-Layers with Selective Absorption in the Visible Range

This work reports the growth of layered nickel hydroxide/gold films by sol-gel and dip-coating methods to obtain colored films for applications in switchable optical devices. The nickel and gold-based films were deposited on mica and glass plates from alcoholic sols. The distribution of electron density inhomogeneities (voids, nickel and gold particles) in the films was determined by means of small angle X-ray scattering (SAXS). The SAXS measurements were used to determine the nickel and gold particle sizes and to give guidelines to the appropriate chemical route to deposit homogeneous colored films. X-ray diffraction (XRD) was used to monitor the crystalline properties. Transmission electron microscopy (TEM) was used to observe the nanostructure of the gold particles and atomic force microscopy (AFM) to analyze the film surface. Spectral transmission was used to investigate the optical properties in these different layered systems, which present an absorption band in the visible region due to the gold aggregates. The composite material is deep blue. The analyses of SAXS data, TEM and AFM pictures are consistent, i.e., the formed Au particles are polydisperse in size and their clustering depends on the NiO _x H _y layer. The Au particles are polycrystalline, with [111]-preferred orientation, as determined by XRD. The nickel oxy-hydroxide matrix is amorphous.     

On-line tracking of the coating of nanoscaled silica with titania nanoparticles via zeta-potential measurements

Nanoscaled spherical silica particles were directly coated with the titania nanoparticles by means of a heterogenic coagulation. Silica was prepared by the Stöber method, titania by a hydrolysis–condensation reaction of tetrapropylorthotitanate under acidic conditions. The on-line tracking of the coating process was performed by measuring the change in zeta potential during the gradual addition of a titania sol to the spherical silica particles. Silica particles of various sizes were used to determine the consumption of the titania sol in the dependence upon the particle size. The coated and uncoated particles were characterized by zeta-potential measurements, acoustic attenuation spectroscopy, dynamic light scattering, and scanning electron microscopy.     

Time-resolved SAXS study of the effect of a double hydrophilic block-copolymer on the formation of CaCO3 from a supersaturated salt solution

The effect of a double hydrophilic block-copolymer additive (made of polyaspartic acid and polyethyleneglycol, pAsp(10)-b-PEG(110)) on the initial formation of calcium carbonate from a supersaturated salt solution has been studied in situ by means of time-resolved synchrotron small-angle X-ray scattering (SAXS). A stopped-flow cell was used for rapidly mixing the 20 mM aqueous reactant solutions of calcium chloride and sodium carbonate. In reference measurements without polymer additive the very rapid formation of primary, overall spherical CaCO(3) particles with a radius of ca. 19 nm and a size polydispersity of ca. 26% was observed within the first 10 ms after mixing. A subsequent, very rapid aggregation of these primary particles was evidenced by a distinct upturn of the SAXS intensity at smallest angles. During the aggregation process the size of the primary particles remained unchanged. From an analysis of the absolute scattering intensity the mass density of these particles was determined to 1.9 g/cm(3). From this rather low density it is concluded that those precursor particles are amorphous, which has been confirmed by simultaneous wide-angle X-ray diffraction measurements. Upon adding 200 pm of the block-copolymer no influence on the size, the size polydispersity and morphology of the primary particles, nor on the kinetics of their formation and growth, was found. On the other hand, the subsequent aggregation and precipitation process is considerably slowed down by the additive and smaller aggregates result. The crystalline morphology of the sediment was studied in situ by WAXS ca. 50 min after mixing the reactants. Several diffraction rings could be detected, which indicate that a transformation of the metastable, amorphous precursor particles to randomly oriented vaterite nanocrystallites has taken place. In addition, a few isolated Bragg spots of high intensity were detected, which are attributed to individual, oriented calcite microcrystals that nucleated at the wall of the capillary.     

Urea hard segment morphology in flexible polyurethane foam

A series of flexible polyurethane slabstock foam samples were prepared with varying water content and studied using transmission electron microscopy (TEM), video-enhanced optical microscopy (VEM), and small-angle X-ray scattering (SAXS). A new TEM sample preparation technique was developed in which the foam is impregnated with water, frozen, and microtomed, and the polyether soft segment is selectively degraded in the electron beam. Structures of two size scales were detected. A texture with grains (“urea aggregates”) 50–200 nm in size was imaged using both VEM and low-magnification TEM for foams with formulations containing more than 2 pphp water. For the first time, images of urea hard segment microdomains in polyurethane foam (approximately 5 nm in size) were obtained using high-magnification TEM. A microdomain spacing of approximately 6–8 nm was estimated from the SAXS scattering profiles. Glycerol was added to one of the formulations in order to modify the urea microphase separation and to give insight into morphology development in molded polyurethane foam systems. No structure was observed in low-magnification TEM images of the glycerol-modified foam, although smaller structures (hard segments) were detected at high magnification and by SAXS. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 573–581, 1998     

Nanocomposites of polymers and metals or semiconductors: Historical background and optical properties

Upon transmission of visible light through composites comprising of a transparent polymer matrix with embedded particles, the intensity loss by scattering is substantially reduced for particle diameters below 50–100 nm (nanoparticles, nanosized particles). As a consequence, related materials (nanocomposites) have found particular interest in optical studies. The first part of this article deals with a historical survey on nanoparticles and nanocomposites and the importance of small particle sizes on their optical properties. The second part focuses on results from our laboratory concerning nanocomposites with extremely high or low refractive indices and dichroic nanocomposites and their application in bicolored liquid crystal displays (LCD). The inorganic colloids required for these studies (lead sulfide, iron sulfides, gold, and silver) were prepared in situ in presence of a polymer or isolated as redispersable metal colloids modified at the surface with a self‐assembled monolayer (SAM) of an alkanethiol. The nanocomposites themselves were finally obtained by coprecipitation, spin coating, solvent casting or melt extrusion, with poly(ethylene oxide), gelatin, poly(vinyl alcohol) and polyethylene as matrix polymers.     

Nucleation, structure and lamellar morphology of isotactic polypropylene filled with polypropylene-grafted multiwalled carbon nanotubes

Polypropylene-based nanocomposites filled with polypropylene-grafted multiwalled carbon nanotubes (PP-g-MWNT) were compared to PP samples filled with pristine MWNT. The effect of such additives on the structure and morphology of the polymer matrix was studied by small angle X-ray scattering (SAXS), wide angle X-ray diffraction (WAXD), polarized light optical microscopy (PLOM) and differential scanning calorimetry (DSC). PP-g-MWNT allowed a more efficient and unhindered crystallization at a lamellar level, while MWNT disrupted the order of lamellar stacks, probably because of their tendency to aggregate. A common trend of tensile properties and lamellar morphology as a function of filler content was noted in the series filled with functionalized carbon nanotubes.     

Morphology and cation local structure in a blend of copper-neutralized carboxy-terminated polybutadiene and poly(styrene-co-4-vinylpyridine)

Carboxy-terminated polybutadiene neutralized with Cu²⁺ (CuPBD) and its blend with poly(styrene-co-4-vinylpyridine) (SVP) were examined by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), small-angle x-ray scattering (SAXS), and extended x-ray absorption fine structure (EXAFS) spectroscopy. The DSC results indicate that in the blend substantial mixing occurs in the CuPBD-rich phase, although complete miscibility is not achieved, and the SVP-rich phase remains relatively pure. The TEM micrographs indicate that the morphology, while irregular, is reasonably described as bicontinuous, with a domain size of order 100 nm. The SAXS patterns show that the ionic aggregates present in CuPBD are destroyed upon blending, which is interpreted as being due to steric hindrances between ionic groups coordinated to vinylpyridine nitrogens. The EXAFS radial structure function of the blend exhibits a marked decrease in the Cu-Cu peak in comparison with CuPBD, indicating a change in local structure upon blending. The results indicate that some of the SVP is miscible with CuPBD owing to complexation between the pendant pyridine groups and the Cu²⁺ ions, which disrupts the ionic aggregates. However, the two materials are not fully miscible, leading to a rather coarse two-phase morphology.     

Dependence of silica particle sizes on network chain lengths,silica contents,and catalyst concentrations in in situ‐reinforced polysiloxane elastomers

Poly(dimethylsiloxane) networks were prepared by tetrafunctionally end‐linking hydroxyl‐terminated chains with tetraethoxysilane (TEOS). Molecular composites were then prepared by in situ sol–gel reactions on additional TEOS swelled into the networks, resulting in the formation of reinforcing silica fillers within the host elastomers. The amount of filler generated generally increased linearly with an increase in the TEOS swelling ratio, as expected. The silica particles formed were examined by small‐angle X‐ray scattering. Of particular interest were the relationships between particle size and molecular weight M_c of the network chains (mesh sizes), amount of filler introduced, and catalyst concentration. Particle sizes were smallest for the smallest values of M_c, possibly demonstrating constraining effects from the very short network chains. At fixed M_c and filler concentrations, higher catalyst concentrations gave larger particles. Increase in filler concentration generally had little effect on particle size at low and high loadings, but markedly increased sizes at intermediate levels (10–20 wt %), presumably caused by coalescence of the scattering entities into considerably larger aggregates. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1421–1427, 1999     

On variations in size distributions of particles and aggregates upon dilution of magnetic fluids

Variations in size distributions of particles and aggregates upon dilution of kerosene-based magnetic fluids have been studied by dynamic light scattering. The data obtained on samples of magnetic fluids produced by three different manufacturers have shown that the dilution of an initial concentrated magnetic fluid leads to the formation of a system of unstable aggregates with sizes ranging from 70?100 nm to 1 μm. The aggregates peptize for 2?4 days to result in the establishment of stationary particle and aggregate size distributions.