Optimize the thermoelectric performance of CdO ceramics by doping Zn

The thermoelectric performance of CdO ceramics was enhanced by simultaneously optimizing the electrical and thermal transport properties via a small amount of Zn doping(≤3%). The introduction of Zn can obviously increase the electrical conductivity of CdO due to the simultaneous increase of carrier concentration and mobility, and eventually results in an improvement in power factor. Zn doping is also effective in suppressing the thermal conductivity of CdO because of stronger phonon scatterings from point defects, Zn-riched second phase, and grain boundaries. A best ZT of about 0.45 has been achieved in the Cd_(1-x)Zn_xO systems at about 1000 K, which is comparable to the highest values reported for other n-type oxide TE materials.     

Thermoelectric properties and structural instability of type-I clathrate Ba8Ga16Sn30 at high temperatures

Type-I clathrate Ba₈Ga₁₆Sn₃₀ is known as a typical example showing glass-like behavior in the thermal conductivity at low temperatures. We report on thermoelectric properties above room temperature for the p- and n-type single crystals which were grown from Ga–Sn double flux and Sn single flux, respectively. The measurements of electrical resistivity showed hysteretic behaviors when the sample was heated to 600 K. Powder X-ray diffraction analysis indicated that the type-I structure changed to the type-VIII after the sample was heated to 600 K. By using the data of Seebeck coefficient, electrical resistivity, and thermal conductivity, we estimated the dimensionless figure of merit ZT for the type-I Ba₈Ga₁₆Sn₃₀. For the p- and n-type samples, the values of ZT reach 0.58 and 0.50 at around 450 K, respectively, which values are approximately half of those for the type-VIII counterparts.     

Microstructure and thermoelectric properties of Zn1−xAlxO ceramics fabricated by spark plasma sintering

Al-doped ZnO powders were synthesized via solid reaction between Zn(OH)₂ and Al(OH)₃ and consolidated by spark plasma sintering (SPS) to fabricate fine-grained Zn_1−xAl_xO ceramics as a thermoelectric material. X-ray diffraction and spectrophotometer experiments revealed that Al doping into ZnO is enhanced by the present process, and consequently the SPS-processed Zn_1−xAl_xO samples show significantly improved electrical conductivity as compared with those prepared via mixing ZnO and Al₂O₃ oxide powders. Because of the combined effect of Al doping and grain refinement, the present Zn_1−xAl_xO ceramics show much lower thermal conductivity, which also results in an enhanced dimensionless figure of merit (ZT), than un-doped ZnO oxides prepared also by SPS.     

Thermoelectric properties and electronic structure of Al-doped ZnO

Impure ZnO materials are of great interest for high temperature thermoelectric application. In this work, we present the effects of Al-doping on the thermoelectric properties and electronic structures of a ZnO system. We find that, with increasing Al concentrations, the electrical conductivity increases and the thermal conductivity decreases significantly, whereas, the Seebeck coefficient decreases slightly. Nevertheless, the figure of merit (ZT) increases owing to high electrical conductivity and low thermal conductivity. On the other hand, the electronic band structures show that the position of the Fermi level is moved upwards and the bands split near the valence-band top and conduction-band bottom. This is due to the interaction between the Al3p and Zn4s orbitals, which drive the system towards semimetal. Besides, the Density Of States (DOS) analysis shows that the introduction of Al atom obviously reduces the slope d(DOS)/dE near the Fermi level. Based on the calculated band structures, we are able to explain qualitatively the measured transport properties of the Al-doped ZnO system.     

Thermoelectric properties of Ni-doped CuInTe2

Polycrystalline samples of composition Cu_1−xNi_xInTe₂ (for x=0–0.05) were synthesized from elements of 5 N purity using a solid-state reaction. The phase purity of the products was verified by X-ray diffraction. Samples for measurement of the transport properties were prepared using hot-pressing. The samples were then characterized by the measurement of electrical conductivity, the Hall coefficient, the Seebeck coefficient, and the thermal conductivity over a temperature range of 300–675 K. All of the samples demonstrate p-type conductivity. We discuss the influence of Ni substitution on the free carrier concentration and the thermoelectric performance. The investigation of the thermoelectric properties shows an improvement up to 50% of ZT in the temperature range of 300–600 K.     

Thermal conductivity of thermoelectric Al‐substituted ZnO thin films

ZnO:Al thin films with a low electrical resistivity were grown by magnetron sputtering on sapphire substrates. The cross‐plane thermal conductivity (κ = 4.5 ± 1.3 W/mK) at room temperature is almost one order of magnitude lower than for bulk materials. The thermoelectric figure of merit ZT at elevated temperatures was estimated from in‐plane power factor and the cross‐plane thermal conductivity at room temperature. It is expected that the thermal conductivity drops with increasing temperature and is lower in‐plane than cross‐plane. Consequently, the thin film ZT is at least three times higher than for bulk samples at intermediate temperatures. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ca2+掺杂对CdO多晶热电性能的影响

以CaCO₃作为Ca²⁺源, 利用传统固相烧结法制备了Cd_1-xCa_xO (x=0, 0.01, 0.03, 0.05) 多晶块体样品并研究了Ca²⁺掺杂对CdO高温热电性能的影响. CaCO₃的掺入会导致CdO多晶载流子浓度降低, 使Cd_1-xCa_xO的电阻率ρ和塞贝克系数的绝对值|S|增大、电子热导率κ_e减小. 同时, 在CdO中掺入CaCO₃会引入点缺陷和气孔并可抑制CdO晶粒长大、晶界增多, 从而增加了对声子的散射, 使样品的声子热导率κ_p减小. 由于总热导率的大幅降低, Cd_0.99Ca_0.01O多晶样品在1000 K时的热电优值ZT可达0.42, 比本征CdO提高了约27%, 为迄今n型氧化物热电材料报道的最好结果之一.     

Thermoelectric properties of Ca3−xYxCo4O9+δ ceramics

The Ca_3?xY_xCo₄O_9+δ (x=0, 0.15, 0.3) ceramics were prepared by combining the polyacrylamide gel method and the spark plasma sinter (SPS) technology in order to improve the thermoelectric properties of Ca₃Co₄O_9+δ ceramics. The Seebeck coefficients and the resistivities of the Y-doped samples were obviously enhanced due to the decrease of carrier concentration, and their thermal conductivities were decreased due to the impurity scattering effect. The thermoelectric properties were improved at high temperature by Y-doping according to the power factor analysis and the thermoelectric figure of merit (ZT) data. The optimized figure of merit ZT=0.22 at 973 K was obtained for Ca_2.7Y_0.3Co₄O_9+δ.     

Cu addition and its role in thermoelectric properties and nanostructuring in the series compounds (InSb)nCum

We have performed a comparative investigation of the series compounds (InSb)_nCu_m to assess the roles of Cu addition on the thermoelectric properties and nanostructuring in bulk InSb. Detailed temperature dependent transport properties including electrical conductivity, the Seebeck coefficient, and thermal conductivity are presented. The Seebeck coefficients of In₂₀Sb₂₀Cu (m:n = 1:20) are increased by 13 percent in magnitude if compared to those of InSb, which is responsible for the 22 percent enhancement in the highest ZT value at 687 K. Although the magnitudes of κ_L are larger than those of InSb over the entire temperature range, a remarkable reduction in lattice thermal conductivities (κ_L) was observed with measuring temperature elevation. Such changes are mainly due to the precipitation of a large number of Cu₉In₄ nanoparticles with the size of smaller than 5 nm, dispersed in the matrix observed using high resolution transmission electron microscopy (HRTEM) images.     

DFT investigation on the electronic and thermoelectric properties of ternary semiconductor AgBiS2 for energy conversion application

Via the FP-APW+lo method, we have performed a systematic theoretical study of the structural, electronic and thermoelectric properties of β-AgBiS₂ compound. The estimated structural properties such as cell parameters a and c, c/a ratio and internal parameters are in reasonable agreement with the earlier measured one. From band structure calculations we have found that β-AgBiS₂ is semiconductor with a band gap of 1.23 eV using the TB-mBJ approximation. In addition, the analysis of the total and partial DOS shows a considerable hybridization between Ag ‘d’ states and S ‘p’, Bi ‘s’ states indicating that both Ag-S and Bi-S have covalent character. The main thermoelectric properties such as electrical conductivity, thermo-power, electronic thermal conductivity, power factor and figure of merit are calculated and discussed. We observed that ZT increases when temperature is augmented and reached its maximum of 0.95 and 0.85 at 2 × 10¹⁹ cm⁻³ for p and n-type doping, respectively. Thus, β-AgBiS₂ compound has interesting thermoelectric properties in both p and n-type doping.     

Thermoelectric properties of CoSb3 with maize‐like structure

Maize‐like CoSb₃ powders were obtained via the chemical alloying method. After the consolidation of the nanopowder using hot press, the CoSb₃ compact shows a higher Seebeck coefficient and lower thermal conductivity. For the investigated CoSb₃, a ZT of 0.15 at 673 K is shown. Though the achieved ZT does not reach the optimal value (0.17 to 0.18) for pure CoSb₃, due to its lower electrical conductivity, the novel structure fabrication provides an interesting and promising approach to enhancing the thermoelectric performance. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Thermoelectric properties of Cr1−xMoxSi2

The thermoelectric properties of Mo-substituted CrSi₂ were studied. Dense polycrystalline samples of Mo-substituted hexagonal C40 phase Cr_1−xMo_xSi₂ (x=0–0.30) were fabricated by arc melting followed by spark plasma sintering. Mo substitution substantially increases the carrier concentration. The lattice thermal conductivity of CrSi₂ at room temperature was reduced from 9.0 to 4.5 W m⁻¹ K⁻¹ by Mo substitution due to enhanced phonon–impurity scattering. The thermoelectric figure of merit, ZT, increases with increasing Mo content because of the reduced lattice thermal conductivity. The maximum ZT value obtained in the present study was 0.23 at 800 K, which was observed for the sample with x=0.30. This value is significantly greater than that of undoped CrSi₂ (ZT=0.13).     

Effect of tellurium on electrical and structural properties of sintered silicon nitride ceramics

The effects of tellurium (Te) additives on electrical conductivity, dielectric constant and structural properties of sintered silicon nitride ceramics have been studied. Different amounts of Te (10% and 20%) were added as sintering additives to silicon nitride ceramic powders and sintering was performed. Microstructure and composition were investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrical conductivity and dielectric constant (ε′) increase exponentially with temperature greater than 800 K. The electrical conductivity and dielectric constant increase but activation energy decreases from 0.72 to 0.33 eV with the increase of Te concentration. However, the conductivity increases five orders of magnitude at the concentration of 10% of Te in Si₃N₄. As the Te concentration increases the sintered silicon nitride ceramics become denser. These types of samples can be used as high temperature semiconducting materials.     

Preparation and thermoelectric properties of AgPb18SbTe20−xSex (x = 1, 2, 4) materials

AgPb₁₈SbTe_20−xSe_x (x = 1, 2, 4) bulk materials were prepared by combining hydrothermal synthesis and melting. Thermoelectric properties were measured from room temperature up to 773K. The materials showed n-type conduction and exhibited degenerate semiconductor behavior. The power factors of the materials varied greatly with increase of Se content (x). Partial substitution of Se for Te in AgPb₁₈SbTe₂₀ resulted in remarkable reduction of thermal conductivity in the whole temperature range and increase of power factor at lower temperatures; therefore, the dimensionless figure of merit, ZT, was enhanced below 600K. A maximum ZT value of ∼0.82 is obtained at 523K for the AgPb₁₈SbTe₁₈Se₂ sample.     

Thermal, structural and complex impedance analysis of Mn modified BaTiO3 electroceramic

The polycrystalline samples of BaTi_1−xMn_xO₃ (BMT) ferroelectric ceramics with x=0, 0.04, 0.07, 0.10 have been prepared using a solid-state reaction technique. The calcination temperature of the samples was optimized by thermal gravimetric analysis and repeated firing. Preliminary structural study using X-ray diffraction technique at room temperature suggests that structure of Mn modified compounds (BMT) change into orthorhombic crystal system from tetragonal crystal system. The field emission scanning electron micrographs (FE-SEM) show uniform grain distribution throughout the surface of the samples. Complex impedance analysis (CIS) has been carried out to investigate the electrical properties of BMT. The real and imaginary part of complex impedance plots exhibit semicircle(s) in the complex plane. The bulk resistance of the material decreases with rise in temperatures similar to a semiconductor. The variation of bulk ac conductivity with frequency shows that the compounds exhibit dispersive type electrical conductivity.     

熔体旋甩法合成n型(Bi_(0.85)Sb_(0.15))_2(Te_(1-x)Se_x)_3化合物的微结构及热电性能

采用熔体旋甩结合放电等离子烧结(MS-SPS)技术制备了单相n型四元(Bi0.85Sb0.15)2(Te1-xSex)3(x=0.15,0.17,0.19,0.21)化合物,并对所得样品的微结构和热电传输性能进行了系统研究.样品自由断裂面的场发射扫描电子显微镜及抛光面的背散射电子成分分析表明:块体材料晶粒细小,晶粒排列紧密,成分分布均匀且相结构单一,样品中存在大量10—100nm的层状结构.随着Se含量x的增加,样品的电导率和热导率逐渐增加,而Seebeck系数逐渐降低.相比商业应用的区熔材料,MS-SPS方法合成的高Se组成的样品均在425K后表现出更高的ZT值,其中(Bi0.85Sb0.15)2(Te0.83Se0.17)3样品具有最高的ZT值,在360K可达到0.96,并在320—500K均保持较高的ZT值,500K时其ZT值相比区熔材料提高了48%.此外,通过调节Se的含量,可以有效地调控材料的ZT峰值出现的温度段,这对多级或梯度热电器件的制备具有重要意义.     

On the mechanism of electronic transport in polycrystalline CdO thin films

Cadmium Oxide (CdO) thin films (d = 0.16−0.62 μm) were deposited onto glass substrates by thermal evaporation under vacuum (quasi closed volume technique) of high purity (99.99%) CdO polycrystalline powders. The substrate temperature was 300 and 473 K, respectively. After a post-deposition heat treatment, the temperature dependence of the electrical conductivity becomes reversible. The electronic transport mechanism in studied samples is explained in terms of Seto’s model for polycrystalline semiconducting films. The values of optical bandgap have been determined from absorption spectra.     

Thermoelectric Figure-of-Merit Calculations in Heavily Doped p-Type Lead Telluride

The thermoelectric properties of heavily doped p-PbTe have been studied theoretically in the temperature range from 300 to 900 K. Calculations are based on a three-band model of the PbTe spectrum that takes the transport of electrons and light holes into account in the L-extrema and heavy holes in the Σ-extrema. On the basis of the Boltzmann kinetic equation, a complete set of relevant kinetic characteristics, including the electrical and thermal conductivities, the Seebeck coefficient, and the thermoelectric figure-of-merit ZT has been calculated. All calculated thermoelectric quantities agree well with the available experimental data in the entire temperature interval from 300 to 900 K. The calculation reproduces a significant increase in the thermoelectric figure-of-merit to the value ZT = 1.2 which has been recently detected experimentally in heavily doped p-PbTe samples.     

Low temperature thermoelectric properties of Bi2−xSbxTeSe2 crystals near the n–p crossover

Seebeck coefficients, electrical resistivities, thermal conductivities and figure of merit ZT of Bi_2?xSb_xTeSe₂ crystals (x=0.8, 0.9, 1.0, 1.1, and 1.2) measured along the hexagonal basal plane are presented. The crystals gradually change from n- to p-type with increasing Sb content, with the crossover lying in the region between x=1.0 and 1.1. The crossover is accounted for by a simple (p–n) electron-hole compensation model, as supported by carrier concentrations determined from Hall measurements. ZT was found to be maximized near the crossover on the p-type side, with the high electrical resistance of the Se-rich crystals apparently the limiting factor in the performance. These materials may serve as a basis for future nanostructuring or doping studies.     

Investigation of the possibilities for increasing the thermoelectric figure of merit of nanostructured materials based on Bi2Te3-Sb2Te3 solid solutions

The transport coefficients and thermoelectric figure of merit ZT for bulk nanostructured materials based on Bi₂Te₃-Sb₂Te₃ solid solutions have been investigated theoretically. Similar materials prepared by rapid quenching of the melt with the subsequent grinding and sintering contain amorphous and nanocrystalline regions with different sizes of particles. According to the performed estimations, the thermoelectric figure of merit of the amorphous phase can exceed the value of ZT for the initial solid solution by a factor of 2?C3 primarily due to the significant decrease in the thermal conductivity. The effective transport coefficients of the medium as a whole have also been investigated as a function of the parameters of each phase, and the concentration range of the amorphous phase, which corresponds to the effective values ZT > 1, has been determined.