Stabilizing action of polymeric plasticisers in PVC

Polymeric plasticisers gained considerable success in PVC formulations in the early eighties and there are now several manufacturers of plasticising additives based on polymeric compositions in the USA. The good performance of these additives has been considered in the technical literature. For epoxy polymeric plasticisers, an improvement of heat and U.V. stability was also observed as a function of the oxirane oxygen content in formulations. In this paper we refer to some experimental tests on thermal and U.V. light stabilising action of linear low molecular polyesters, based on glycols and dibasic aliphatic acids, which possess a good plasticising effect and low toxicity. Creep tests and calculations of isochronous creep modulii were used to evaluate the stability of PVC formulations.     

Effect of some additives on the photoxidation of rigid PVC

The photoxidative degradation of PVC was studied by i.r. and u.v. spectroscopy and gel permeation chromatography. It was found that the photoxidative degradation of unprocessed PVC is an auto-accelerating chain scission process. Carboxylic groups were found to be the main product formed during degradation. The molecular weights $\text{M}{}_{\mathrm{n}}$ and $\text{M}{}_{\mathrm{w}}$ both decreased, but the molecular weight distribution widened with increasing length of exposure. Single additives, such as calcium stearate. Wax E and a solid organotin stabilizer, altered the rate but not the mode of the degradation. Combination of the three additives changed the mode of the photoxidation from auto-accelerating to constant rate of degradation. Processing at 170° with the combined additives increased the rate constants.     

Characterization of PVC BY SEC. II. One Shot Chromatography of the Organic Components of PVC Compounds

Abstract

1,2,4-Trichlorobenzene at 90°C proved to be a universal solvent for the common organic components of PVC compounds except crosslinked impact modifiers. Size exclusion chromatography was carried out with 8 different components, with a PVC-U compound and plate out formed during its extrusion using both RI and IR detection. In the RI detector PVC shows a very low detector response. It is therefore possible to analyze the whole organic fraction of the compound without prior precipitation of PVC. Using RI/IR double detection, an “one shot” analysis of the PVC matrix and of all the soluble additives can be accomplished.     

Secondary Processes of Thermal Degradation of PVC

A brief summary of secondary processes in PVC thermal degradation is given. This includes some details of crosslinking and gel formation, cyclization, chain scission and benzene formation, Diels-Alder reaction with additives, as well as oxidation of polyenes.     

Spectroscopic and Morphological Study of Irradiated PVC Films Doped with Polyphosphates Containing 4,4'-Methylenedianiline

Russian Journal of Applied Chemistry - Polyphosphates containing 4,4'-methylenedianiline moiety were synthesized and their use as polyvinyl chloride (PVC) additives to enhance PVC...     

聚氯乙烯超滤膜的溶剂蒸发速度影响研究

本文对 PVC 超滤膜的浇铸膜溶剂体系蒸发速度进行了研究,着重讨论了第二添加剂的种类和含量对蒸发速度的影响.结果表明,溶剂蒸发速度及蒸发时间都是影响 PVC 超滤膜结构与性能的重要因素,而第二添加剂又是影响溶剂蒸发速度的一个重要因素.     

Study of the migration of additives from plasticized PVC

The aim of this paper is to study the interactions between packaging and food. For that purpose, additives were first characterized. Kinetic studies of their specific migrations have been carried out by using different analytical methods such as gas chromatography, Fourier transform infrared spectroscopy, atomic absorption spectrometry and differential scanning calorimetric analysis. The influence of various parameters such as temperature, agitation, nature of food simulant and initial concentration of plasticizer was considered.     

Mechanisms of antioxidant action: Synergism between tin stabilizers and polymer-bound antioxidants in the u.v. stabilization of PVC

It is shown that a conventional tin stabilizer (dibutyltin maleate) (DBTM) forms an effective synergistic u.v. stabilizing combination when used in conjunction with a bound phenolic antioxidant (BHBM) and a bound u.v. stabilizer (EBHPT). These additives become bound to the polymer through sulphur during processing in the presence of DBTM and it is suggested that the sulphide of the adduct makes its own contribution to u.v. stabilization by acting as a peroxide decomposing (PD-C) antioxidant during photo-oxidation. However, the 2-hydroxybenzophenone function appears to be an essential part of the system and is probably involved in quenching of excited states of the intermediate sulphoxides which precede the formation of the PD-C antioxidant.     

Effect of various additives on the performance of a newly developed PVC based potentiometric sensor for anionic surfactants

A new poly(vinyl chloride) PVC membrane electrode to determine monomer concentrations of dodecylbenzenesulphonate ions (DBS⁻) based on a neutral ion-pair carrier complex of dodecyltrimethylammonium–dodecylbenzenesulphonate (DTA⁺–DBS⁻), is reported here. The electrode exhibits a slope of 51.25 mV per decade for DBS⁻ ions. The DBS⁻ ion selective electrode (ISE) can determine monomer units down to concentrations as low as 3.32 × 10⁻⁴ M. The effect of three kinds of additives, i.e. alcohols, glycols and triblock polymers on the performance of the surfactant selective electrode is studied systematically. The effect of foreign anions along with primary ions on the performance of ion-selective electrode is investigated in terms of potentiometric selectivity coefficients, which were determined using the fixed interference method (FIM) at 1.0 × 10⁻² M concentration of foreign anions. The sensor responds well to the surfactant ions in the presence of additives at lower concentration. The Gibbs free energy of micelle formation (ΔG_m) of sodium dodecylbenzenesulphonate (SDBS) in the presence of various additives is calculated and found to vary differently with respect to the increase in the amount of additives. The sensor worked in the acidic pH range with a short response time of 30 s. The lifetime of the sensor is more than three months. The sensor was further used to determine the amount of DBS⁻ in local detergents. This method of determining anionic surfactants was found to be quite accurate when compared with classical methods.     

Features of the propagation of laminar spherical flames initiated by a spark discharge in mixtures of methane,pentane, and hydrogen with air at atmospheric pressure

Using high-speed digital color cinematography, we studied the propagation of a laminar spherical flame in stoichiometric mixtures of hydrogen, methane, and pentane with air in the presence of additives at atmospheric pressure in constant-volume reactors, and derived quantitative data on the time of formation of a stable flame front. Cellular flames caused by gas-dynamic instability attributable to convective flows arising during the afterburning of gas were observed in hydrocarbon-air stoichiometric mixtures diluted with inert additives. It was found that the effect of additives of carbon dioxide and argon (>10%) and minor additives of CCl₄ on the combustion of hydrocarbons, and of propylene on the combustion of hydrogen-rich mixtures, lead to periods of delay in the development of a laminar spherical flame; in addition, additives of propylene promote the combustion of hydrogen poor mixtures.     

过渡金属添加剂对煤热解脱硫的影响

利用坩埚焦考察了过渡金属添加剂Fe、Cr和Mn的不同形态在焦化过程中对高硫焦煤中硫脱除的影响,并通过固定床热解实验考察了不同气氛下添加剂对煤热解脱硫及含硫化合物逸出的影响。结果表明,不同金属添加剂对煤中硫形态有不同影响,氧化性较高的Fe3+降低了煤中黄铁矿硫的含量,而其他金属添加剂对煤中硫形态影响不大。在模拟焦化过程中,铬系添加剂提高了热解脱硫率,而铁系和锰系添加剂降低了脱硫率;负载Cr3+的介休煤在不同气氛下的热解表明,氮气抑制了Cr的脱硫作用,显著地减少了含硫气体的生成量,并使煤中易脱除硫转化为稳定的有机硫;还原性气氛有利于Cr3+添加剂的脱硫作用,显著地增加了含硫气体的生成量;焦炉气和氢气下添加剂对热解脱硫及煤热解过程中含硫气体逸出的影响相似,焦炉气可以作为提高过渡金属添加剂脱硫性能的反应气体。     

Overview of the recent literature on flame retardancy and smoke suppression in PVC

This paper presents an overview of the recent literature on flame retardancy of poly(vinyl chloride) (PVC). A short overview of mechanisms of thermal decomposition of PVC, especially those which lead to char formation, is also presented because this gives insight into the mechanisms of flame retardant action. New developments in the area are mostly focused on combinations of various flame retardants and smoke suppressants in the search for synergistic effects. Because different additives show different mechanisms of action, synergistic combinations are very probable. New developments in phosphate ester plasticizers are reported in the literature. Copyright © 2005 John Wiley & Sons, Ltd.     

Determination of additives in PVC material by UV laser ablation inductively coupled plasma atomic emission spectrometry

UV laser ablation inductively coupled plasma atomic emission spectrometry (LA-ICP-AES) has been applied to the direct determination of additives in solid poly(vinyl chloride) materials. A Nd:YAG laser, operating at its fourth harmonic (266 nm), was used with a beam masking device, in the most reproducible conditions, to introduce solid particles into the plasma torch of a simultaneous ICP-AES system. Emphasis was placed on both precision and accuracy in the analysis of PVC materials by LA-ICP-AES. A series of six in-house PVC reference materials was prepared by incorporating several additives in increasing concentrations. Three alternative methods were evaluated to certify the amount of incorporated elements: ICP-AES with sample dissolution, NAA and XRF. Satisfactory results and good agreement were obtained for seven elements (Al, Ca, Cd, Mg, Sb, Sn and Ti) among the ten incorporated. Sample homogeneity appeared to be satisfactory, and calibration graphs obtained by LA-ICP-AES for several elements are presented. Finally, the performance of the technique in terms of repeatability (1.6-5%), reproducibility (2–5%), and limits of detection was investigated.     

The Effect of Hydrotalcite and Zinc Oxide on Smoke Suppression of Commercial Rigid PVC

To reduce the smoke release of poly(vinyl chloride) (PVC) during burning, layered double hydroxides (LDHs) and zinc oxide (ZnO) powders were used to modify the polymer. The results indicated that the addition of LDHs‐ZnO had a significant effect on smoke suppression. The limiting oxygen index (LOI) reached a maximum value and the smoke density rank (SDR) exhibited a minimum value when the weight percentages of LDHs and ZnO in PVC were 3% and 2%, respectively. Thermal stabilities of the modified PVC and degradation products were investigated by means of thermogravimetry and pyrolysis‐gas chromatography‐mass spectra (Py‐GC‐MS). The LDHs‐ZnO obviously accelerated the decomposition of PVC to release hydrogen chloride, and the decomposed PVC consequently produced the trans‐conjugated polyene sequences, which easily formed crosslinked structures. However, a cyclization reaction in PVC chain without the additives produced aromatic compounds such as benzene, toluene, and naphthalene at 350°C. Even though, an amount of aromatic compounds was released from the PVC modified with LDHs‐ZnO at the temperature of 600°C, the content of the decomposed products is relatively lower compared to unmodified PVC.     

Al(OH)3和Mg(OH)2对PVC热解特性的影响研究

利用热重分析仪并借助电导率测定法探讨了Al(OH)3和Mg(OH)2对PVC热解特性的影响,简要分析了其机理。结果表明:加入Al(OH)3和Mg(OH)2后均能增加PVC体系在第一阶段的最大热解速率和残炭量,最大热解速率增加约1倍,残炭量增加约4倍。并且分解产生的结晶水吸收大量的热量,惰性金属氧化物也有利于成核、炭层生长和凝聚,有着明显的阻燃和抑烟作用。HCl毒性气体的释放主要集中在体系的第一阶段,Al(OH)3能促使HCl提前释放,HCl的释放总量增加,Mg(OH)2也能促使HCl提前释放,但HCl的释放总量却是减少的。     

Structure,mechanical, and tribological characteristics of polyurethane modified with nanodiamonds

The effect of modifying additives based on detonation nanodiamonds on the tribological characteristics of polyurethane rubber is studied. Introduction of modifying additives based on detonation nanodiamonds (0.5 wt %) leads to a marked improvement in the antifriction and wear-resistance characteristics under conditions of boundary sliding friction for steel and for lubrication with water. The attained tribological characteristics (total energy loss for friction, weight loss of polymer during tribological contact, maximum admissible working pressure) are well (∼300%) above the corresponding characteristics of foreign analogs. Changes in the tribological characteristics of the formed nanocomposite material are observed, but the elastic and strength characteristics remain unchanged.     

Thermal characterization of nitrile butadiene rubber (NBR)/PVC blends

Summary Nitrile butadiene rubber (NBR) and NBR/PVC blends were produced using 2,2,4-trimethyl-1,2-dihydroquinoline (TMQ) or not as antioxidant. Controlled ozone degradation was performed in several samples. Thermal, compositional and morphological analysis was performed by means of differential scanning calorimetry, thermogravimetry, chemical analysis and scanning electron microscopy. Thermogravimetry analysis shows four mass loss processes related to plastizicer, complex rubber degradation and metallic oxides and other additives. In NBR (NBR/PVC blends) the onset temperature of the first degradation process varies between 227-231°C (259-262°C) and the apparent activation energy between 26 and 36 kJ mol^-1 (36-57 kJ mol^-1), the NBR/PVC samples non degraded presents the higher thermal stability.     

Analytical electron microscopy studies of lithium aluminum hydrides with Ti- and V-based additives

The microstructure of LiAlD(4) with TiCl(3).1/3(AlCl(3)) and VCl(3) additives has been studied during different steps of the decomposition process using electron energy loss spectroscopy and energy-dispersive X-ray spectroscopy in a scanning transmission electron microscope. Energy filtered transmission electron microscopy was used to show elemental distributions in the samples. The spatial distribution of the additives and the main elements within the alanate particles was examined with a resolution of a few nanometers. The analysis of the electron energy loss spectra reveals the chemical state of Al, O, and the additives. Ti and V do not appear to mix chemically with Al to a significant degree. V was found in high concentration in just a few particles, while Ti is more uniformly distributed. All the samples showed evidence of oxidation despite procedures being adopted to avoid exposing the material to air. The additives are oxidized in all the samples, and Al(2)O(3) forms a thin layer at the surface of the particles. This paper gives a comparison between samples at different stages of the decomposition process using different additives.     

How will additives shape the future of plastics?

Additives are essential components of plastic formulations providing maintenance and/or modification of polymer properties, performance and long-term use. The extension of polymer properties by additives has played a substantial role in the growth of plastics. At the beginning of the plastics age additives were used mainly to maintain polymer properties and to help plastics to survive heat treatment during transforming processes. The next generation of additives provided extension of service life as well as modification of mechanical and physical properties. These well-established additives - antioxidants, heat stabilizers, light stabilizers and others - cover the requirements of standard plastics and today's mass applications. The more recent developments of high-performance additives address more stringent or new requirements, more severe processing and use conditions and/or environmental concerns, but still with the main target of maintaining plastic properties. The future will introduce more and more new effects and functionalities through additives in plastic applications tailoring the properties of polymers and offering a vast potential of innovation in the plastics area. Recent examples of emerging technologies show that additives will not only modify the polymer itself and add new properties, but can also, when incorporated into the plastic, beneficially impact properties, which are of high value for the user. The paper shows the role of additives used in plastics from the past to the present with the focus on stabilization and performance of additives incorporated during melt processing, and outlines future trends.     

TG-MS analysis of nitrile butadiene rubber blends (NBR/PVC)

Blends of nitrile butadiene rubber (NBR) with polyvinyl chloride (PVC) are widely used in products such as hoses and seals. As part of a project that uses NBR/PVC blends for manufacturing forest fire hoses, blends of NBR/PVC with various inorganic fillers, such as Mg(OH)₂, china clay (organic modified kaolin) and nano clay (organic modified bentonite) were studied by TG-MS. No significant changes were observed to the type of the polymers’ decomposition products, compared to that of NBR/PVC blend without additives. The most remarkable change was the absence of HCl from decomposition products in the presence of the Mg(OH)₂ additive.