Submerged Arc Breakdown of Sulfadimethoxine (SDM) in Aqueous Solutions

Low voltage, low energy submerged pulsed arcs were used to break-down Sulfadimethoxine (SDM) contamination in aqueous solutions. The SDM concentration decreased exponentially with rate constants of 0.13–1.9 min⁻¹ during processing by pulsed arcs with a pulse repetition rate of 100 Hz, energies of 2.6–192 mJ and durations of 20, 50 and 100 μs. The electrical energy consumption was minimized with short duration pulses––1.5 kW-hr/m³ with 7.5 mJ, 20 μs pulses for 90% SDM removal.     

Cell inactivation studies on yeast cells under euoxic and hypoxic condition using electron beam from microtron accelerator

In the case of sparsely ionizing radiation such as electron, the dose rate and the pattern of energy deposition of the radiation are the important physical factors which can affect the amount of damage in living cells. In the present study, the differences in the cell survival efficiency and dose rate effect in diploid yeast strains Saccharomyces cerevisiae X2180 and Saccharomyces cerevisiae D7 under euoxic and hypoxic condition have been quantified. Irradiation was carried out using 8 MeV pulsed electron beam from Microtron accelerator. The dose per pulse and pulse width of the beam used was 0.6 Gy and 2.3 μs, respectively, which correspond to an instantaneous dose rate of 2.6 × 10⁵ Gy s⁻¹. For survival studies doses were delivered at a rate of 50 pulses per second (an average dose rate of 1,800 Gy s⁻¹). Fricke and alanine dosimeters were used to measure the dose delivered to the sample. A significant difference in the dose response has been observed under euoxic and hypoxic condition. Dose rate effect has been studied by changing the pulse repetition rate of the Microtron and the dose rate used was from 180 to 1800 Gy min⁻¹. A significant dose rate effect was observed under euoxic condition for Saccharomyces cerevisiae X2180 but the same was absent under hypoxic condition. The dose rate effect was absent for Saccharomyces cerevisiae D7 under both irradiation condition. The survival curves are found to be sigmoidal in shape under both condition but with a wider shoulder under hypoxic condition. The D₀ value and the Oxygen Enhancement Ratio (OER) at that point have been derived.     

Non-isothermal kinetic analysis and feasibilty study of medium grade crude oil field

In this research, non-isothermal kinetics and feasibility study of medium grade crude oil is studied in the presence of a limestone matrix. Experiments were performed at a heating rate of 10°C min⁻¹, whereas the air flow rate was kept constant at 50 mL min⁻¹ in the temperature range of 20 to 600°C (DSC) and 20 to 900°C (TG). In combustion with air, three distinct reaction regions were identified in all crude oil/limestone mixtures, known as low temperature oxidation (LTO), fuel deposition (FD) and high temperature oxidation (HTO). The activation energy values were in the order of 5–9 kJ mol⁻¹ in LTO region and 189–229 kJ mol⁻¹ in HTO region. It was concluded that the medium grade crude oil field was not feasible for a self-sustained combustion process.     

Dual purpose laser ablation-inductively coupled plasma mass spectrometry for pulsed laser deposition and diagnostics of thin film fabrication: Preliminary study

PLD (pulsed laser deposition) is an attractive technique to fabricate thin films with a stoichiometry reflecting that of the target material. Conventional PLD instruments are more or less black boxes in which PLD is performed virtually “blind”, i.e. without having great control on the important PLD parameters. In this preliminary study, for the first time, a 213 nm Nd-YAG commercial laser ablation-inductively coupled plasma mass spectrometer (LA-ICPMS) intended for microanalysis work was used for PLD under atmospheric pressure and in and ex situ ICPMS analysis for diagnostics of the thin film fabrication process.A PLD demonstration experiment in a He atmosphere was performed with a Sm_13.8Fe_82.2Ta_4.0 target-Ta-coated silicon wafer substrate (contraption with defined geometry in the laser ablation chamber) to transfer the permanent magnetic properties of the target to the film. Although this paper is not dealing with the magnetic properties of the film, elemental analysis was applied as a means of depicting the PLD process. It was shown that in situ ICPMS monitoring of the ablation plume as a function of the laser fluence, beam diameter and repetition rate may be used to ensure the absence of large particles (normally having a stoichiometry somewhat different from the target). Furthermore, ex situ microanalysis of the deposited particles on the substrate, using the LA-ICPMS as an elemental mapping tool, allowed for the investigation of PLD parameters critical in the fabrication of a thin film with appropriate density, homogeneity and stoichiometry.     

Characterization of the aerosol produced by infrared femtosecond laser ablation of polyacrylamide gels for the sensitive inductively coupled plasma mass spectrometry detection of selenoproteins

A 2D high repetition rate femtosecond laser ablation strategy (2-mm wide lane) previously developed for the detection of selenoproteins in gel electrophoresis by inductively coupled plasma mass spectrometry was found to increase signal sensitivity by a factor of 40 compared to conventional nanosecond ablation (0.12-mm wide lane) [G. Ballihaut, F. Claverie, C. Pécheyran, S. Mounicou, R. Grimaud and R. Lobinski, Sensitive Detection of Selenoproteins in Gel Electrophoresis by High Repetition Rate Femtosecond Laser Ablation-Inductively Coupled Plasma Mass Spectrometry, Anal. Chem. 79 (2007) 6874–6880]. Such improvement couldn't be explained solely by the difference of amount of material ablated, and then, was attributed to the aerosol properties. In order to validate this hypothesis, the characterization of the aerosol produced by nanosecond and high repetition rate femtosecond laser ablation of polyacrylamide gels was investigated. Our 2D high repetition rate femtosecond laser ablation strategy of 2-mm wide lane was found to produce aerosols of similar particle size distribution compared to nanosecond laser ablation of 0.12-mm wide lane, with 38% mass of particles < 1 µm. However, at high repetition rate, when the ablated surface was reduced, the particle size distribution was shifted toward thinner particle diameter (up to 77% for a 0.12-mm wide lane at 285 µm depth). Meanwhile, scanning electron microscopy was employed to visualize the morphology of the aerosol. In the case of larger ablation, the fine particles ejected from the sample were found to form agglomerates due to higher ablation rate and then higher collision probability. Additionally, investigations of the plasma temperature changes during the ablation demonstrated that the introduction of such amount of polyacrylamide gel particles had very limited impact on the ICP source (ΔT~ 25 ± 5 K). This suggests that the cohesion forces between the thin particles composing these large aggregates were weak enough to have negligible impact on the ICPMS detection.     

Introduction of a 20 kHz Nd:YVO4 laser into a hybrid quadrupole time-of-flight mass spectrometer for MALDI-MS imaging

A commercial hybrid quadrupole time–of–flight mass spectrometer has been modified for high-speed matrix-assisted laser desorption ionisation (MALDI) imaging using a short-pulse optical technology Nd:YVO₄ laser. The laser operating in frequency-tripled mode (λ = 355 nm) is capable of delivering 1.5-ns pulses of energy at up to 8 μJ at 5–10 kHz and 3 μJ at 20 kHz. Experiments to improve beam homogeneity and reduce laser speckle by mechanical vibration of the fibre-optic laser delivery system are reported along with data from trial and tissue imaging experiments using the modified instrument. The laser appeared to yield best results for MALDI-MS imaging experiments when operating at repetition rates 5–10 kHz. Combining this with raster imaging allowed images of rat brain sections to be recorded in 37 min. Similarly, images of the distribution of peptides in “on-tissue” digest experiments from tumour tissues were recorded in 1 h and 30 min rather than the 8-h acquisition time previously used. A brief investigation of targeted protein analysis/imaging by multiple reaction monitoring experiments “on-tissue” is reported. A total of 26 transitions were recorded over a 3-s cycle time and images of abundant proteins were successfully recorded.     

A new direct Fourier transform infrared analysis of free fatty acids in edible oils using spectral reconstitution

A new transmission-based Fourier transform infrared (FTIR) spectroscopic method for the direct determination of free fatty acids (FFA) in edible oils has been developed using the developed spectral reconstitution (SR) technique. Conventional neat-oil and SR calibrations were devised by spiking hexanoic acid into FFA-free canola oil and measuring the response to added FFA at 1,712 cm⁻¹ referenced to a baseline at 1,600 cm⁻¹(1,712 cm⁻¹/1,600 cm⁻¹). To compensate for the known oil dependency of such calibration equations resulting from variation of the triacylglycerol ester (C═O) absorption with differences in oil saponification number (SN), a correction equation was devised by recording the spectra of blends of two FFA-free oils (canola and coconut) differing substantially in SN and correlating the intensity of the ester (C═O) absorption at the FFA measurement location with the intensity of the first overtone of this vibration, measured at 3,471 cm⁻¹/3,427 cm⁻¹. Further examination of the spectra of the oil blends by generalized 2D correlation spectroscopy revealed an additional strong correlation with an absorption in the near-infrared (NIR) combination band region, which led to the development of a second correction equation based on the absorbance at 4,258 cm⁻¹/4,235 cm⁻¹. The NIR-based correction equation yielded superior results and was shown to completely eliminate biases due to variations in oil SN, thereby making a single FFA calibration generally applicable to oils, regardless of SN. FTIR methodology incorporating this correction equation and employing the SR technique has been automated.     

<Superscript>239, 240, 241</Superscript>Pu fingerprinting of plutonium in western US soils using ICPMS: solution and laser ablation measurements

Sector field inductively coupled plasma mass spectrometry (SF-ICPMS) has been used with analysis of solution samples and laser ablation (LA) of electrodeposited alpha sources to characterize plutonium activities and atom ratios prevalent in the western USA. A large set of surface soils and attic dusts were previously collected from many locations in the states of Nevada, Utah, Arizona, and Colorado; specific samples were analyzed herein to characterize the relative contributions of stratospheric fallout vs. Nevada Test Site (NTS) plutonium. This study illustrates two different ICPMS-based analytical strategies that are successful in fingerprinting Pu in environmental soils and dusts. Two specific datasets have been generated: (1) soils are leached with HNO₃-HCl, converted into electrodeposited alpha sources, counted by alpha spectrometry, then re-analyzed using laser ablation SF-ICPMS; (2) samples are completely dissolved by treatment with HNO₃-HF-H₃BO₃, Pu fractions are prepared by extraction chromatography, and analyzed by SF-ICPMS. Optimal laser ablation and ICPMS conditions were determined for the re-analysis of archived alpha spectrometry “planchette” sources. The best ablation results were obtained using a large spot size (200 μm), a defocused beam, full repetition rate (20 Hz) and scan rate (200 μm s⁻¹); LA-ICPMS data were collected with a rapid electrostatic sector scanning experiment. Less than 10% of the electroplated surface area is consumed in the LA-ICPMS analysis, which would allow for multiple re-analyses. Excellent agreement was found between ^239+240Pu activities determined by LA-ICPMS vs. activity results obtained by alpha spectrometry for the same samples ten years earlier. LA-ICPMS atom ratios for ²⁴⁰Pu/²³⁹Pu and ²⁴¹Pu/²³⁹Pu range from 0.038–0.132 and 0.00034–0.00168, respectively, and plot along a two-component mixing line (²⁴¹Pu/²³⁹Pu = 0.013 [²⁴⁰Pu/²³⁹Pu] – 0.0001; r ² = 0.971) with NTS and global fallout end-members. A rapid total dissolution procedure, followed by extraction chromatography and SF-ICPMS solution Pu analysis, generates excellent agreement with certified ^239+240Pu activities for standard reference materials NIST 4350b, NIST 4353, NIST 4357, and IAEA 385. ^239+240Pu activities and atom ratios determined by total dissolution reveal isotopic information in agreement with the LA-ICPMS dataset regarding the ubiquitous mixing of NTS and stratospheric fallout Pu sources in the regional environment. For several specific samples, the total dissolution method reveals that Pu is incompletely recovered by simpler HNO₃-HCl leaching procedures, since some of the Pu originating from the NTS is contained in refractory siliceous particles.     

On-line ionic imprinted polymer selective solid-phase extraction of nickel and lead from seawater and their determination by inductively coupled plasma-optical emission spectrometry

Nickel(II) and lead(II) ionic imprinted 8-hydroxyquinoline polymers were synthesized by a precipitation polymerization technique and were used as selective solid phase extraction supports for the determination of nickel and lead in seawater by flow injection solid phase extraction on-line inductively coupled plasma-optical emission spectrometry. An optimum loading flow rate of 2.25 mL min⁻¹ for 2 min and an elution flow rate of 2.25 mL min⁻¹ for 1 min gave an enrichment factor of 15 for nickel. However, a low dynamic capacity and/or rate for adsorption and desorption was found for lead ionic imprinted polymer and a flow rate of 3.00 mL min⁻¹ for 4-min loading and a flow rate of 2.25 mL min⁻¹ for 1-min elution gave a enrichment factor of 5. The limit of detection was 0.33 μg L⁻¹ for nickel and 1.88 μg L⁻¹ for lead, with a precision (n = 11) of 8% (2.37 μg Ni L⁻¹) for nickel and 11% (8.38 μg Pb L⁻¹) for lead. Accuracy was also assessed by analyzing SLEW-3 (estuarine water) and TM-24 (lake water) certified reference materials, and the values determined were in good agreement with the certified concentrations.     

Kinetic study of degradation of heavy oil over MCM-41

Thermogravimetry was applied in order to investigate the catalytic degradation of heavy oil (15.4^oAPI) over silica-based MCM-41 mesoporous molecular sieve. This material was synthesised by the hydrothermal method, using cetyltrimethylammonium bromide as organic template. The physicochemical characterization by nitrogen adsorption, X-ray diffraction, and thermogravimetry, showed that the obtained material presents well-defined structure, with a uniform hexagonal arrangement. The thermal and catalytic degradation of heavy oil was performed by thermogravimetric measurements, in the temperature range from 30 to 900 °C, at heating rates of 5, 10, and 20 °C min⁻¹. By using the model-free kinetics, proposed by Vyazovkin, it was determined that the activation energy to degrade the heavy oil was ca. 128 kJ mol⁻¹, and for degradation of oil in presence of MCM-41, this value decreased to 69 kJ mol⁻¹, indicating the performance of the mesoporores catalyst for the degradation process.     

Certification of methylmercury in cod fish tissue certified reference material by species-specific isotope dilution mass spectrometric analysis

A new cod fish tissue certified reference material, NMIJ CRM 7402-a, for methylmercury analysis was certified by the National Metrological Institute of Japan in the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Cod fish was collected from the sea close to Japan. The cod muscle was powdered by freeze-pulverization and was placed into 600 glass bottles (10 g each), which were sterilized with γ-ray irradiation. The certification was carried out using species-specific isotope dilution gas chromatography inductively coupled plasma mass spectrometry (SSID–GC–ICPMS), where ²⁰²Hg-enriched methylmercury (MeHg) was used as the spike compound. In order to avoid any possible analytical biases caused by nonquantitative extraction, degradation and/or formation of MeHg in sample preparations, two different extraction methods (KOH/methanol and HCl/methanol extractions) were performed, and one of these extraction methods utilized two different derivatization methods (ethylation and phenylation). A double ID method was adopted to minimize the uncertainty arising from the analyses. In order to ensure not only the reliability of the analytical results but also traceability to SI units, the standard solution of MeHg used for the reverse-ID was prepared from high-purity MeHg chloride and was carefully assayed as follows: the total mercury was determined by ID–ICPMS following aqua regia digestion, and the ratio of Hg as MeHg to the total Hg content was estimated by GC–ICPMS. The certified value given for MeHg is 0.58 ± 0.02 mg kg⁻¹ as Hg. Figure NMIJ CRM 7402-a: cod fish tissue for MeHg analysis     

Mercury speciation analysis in seafood by species-specific isotope dilution: method validation and occurrence data

Methylmercury (MeHg) and total mercury (THg) in seafood were determined using species-specific isotope dilution analysis and gas chromatography combined with inductively coupled plasma mass spectrometry. Sample preparation methods (extraction and derivation step) were evaluated on certified reference materials using isotopically enriched Hg species. Solid–liquid extraction, derivation by propylation and automated agitation gave excellent accuracy and precision results. Satisfactory figures of merit for the selected method were obtained in terms of limit of quantification (1.2 μg Hg kg⁻¹ for MeHg and 1.4 μg Hg kg⁻¹ for THg), repeatability (1.3–1.7%), intermediate precision reproducibility (1.5% for MeHg and 2.2% for THg) and trueness (bias error less than 7%). By means of a recent strategy based on accuracy profiles (β-expectation tolerance intervals), the selected method was successfully validated in the range of approximately 0.15–5.1 mg kg⁻¹ for MeHg and 0.27–5.2 mg kg⁻¹ for THg. Probability β was set to 95% and the acceptability limits to ±15%. The method was then applied to 62 seafood samples representative of consumption in the French population. The MeHg concentrations were generally low (1.9–588 μg kg⁻¹), and the percentage of MeHg varied from 28% to 98% in shellfish and from 84% to 97% in fish. For all real samples tested, methylation and demethylation reactions were not significant, except in one oyster sample. The method presented here could be used for monitoring food contamination by MeHg and inorganic Hg in the future to more accurately assess human exposure.     

Polymer-nanoparticle composites composed of PEDOT:PSS and nanoparticles of Ag synthesised by laser ablation

Laser ablation of a solid target material in a liquid environment provides with an easy, straightforward and environmentally friendly method for nanoparticles synthesis as well as with the unique possibility of directly controlling the type of the nanoparticles surface ligands through the liquid choice. In this paper, laser ablation (10.4 ps, 1064 nm and 50 kHz) of a bulk silver target in deionized water, was carried out for nanoparticles synthesis. The synthesised nanoparticles are either pure Ag or A₂O₃ or a mixture of the two materials. Their size distribution follows log-normal function with a statistical median diameter of ≈5 nm. The nanoparticles colloidal solutions were directly mixed after synthesis, with the polymer solution poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) for the formation of polymer-nanoparticles nanocomposite. The nanoparticles readily form bonds with the sulphur atom of PEDOT which results in their uniform distribution within the polymer matrix as well as in a replacement by the nanoparticles of the PSS⁻ as the counteranions to the PEDOT⁺. These effects result in the reduction of the effective insulation of the polymer blend particles by the insulating PSS and furthermore in the electrical conductivity of the nanocomposite becoming higher (by ∼1.5 times) as compared with that of the pure polymer.     

Effect of the shear rate on pullulan production from beet molasses by Aureobasidium pullulans in an airlift reactor

The effect of the shear rate on pullulan production from beet molasses by Aureobasidium pullulans P56 in an airlift reactor was investigated. A maximum polysaccharide concentration (18.5 g/L), biomass dry weight (14.0 g/L), polysaccharide yield (38.5%), and sugar utilization (96%) was achieved at a shear rate of 42 s⁻¹. A. pullulans grown on beet molasses produced a mixture of pullulan and other polysaccharides. The highest value of pullulan proportion (30% of total polysaccharide) was obtained at a low shear rate (42 s⁻¹). The apparent viscosity of the fermentation broth increased as the shear rate increased up to 42 s⁻¹ and then decreased. On the other hand, the dissolved oxygen concentration and the volumetric mass transfer coefficient increased with the increase of the shear rate from 21 to 84 s⁻¹. The external addition of L-glutamic acid, olive oil, and Tween-80 improved significantly the production of crude polysaccharide (27.0 g/L), but the pullulan content of the polysaccharide was low (20%).     

Nitrate as an Oxidant in the Cathode Chamber of a Microbial Fuel Cell for Both Power Generation and Nutrient Removal Purposes

Nitrate ions were used as the oxidant in the cathode chamber of a microbial fuel cell (MFC) to generate electricity from organic compounds with simultaneous nitrate removal. The MFC using nitrate as oxidant could generate a voltage of 111 mV (1,000 Ω) with a plain carbon cathode. The maximum power density achieved was 7.2 mW m⁻² with a 470 Ω resistor. Nitrate was reduced from an initial concentration of 49 to 25 mg (NO₃⁻−N) L⁻¹ during 42-day operation. The daily removal rate was 0.57 mg (NO₃⁻–N) L⁻¹ day⁻¹ with a voltage generation of 96 mV. In the presence of Pt catalyst dispersed on cathode, the cell voltage was significantly increased up to 450 mV and the power density was 117.7 mW m⁻², which was 16 times higher than the value without Pt catalyst. Significant nitrate removal was also observed with a daily removal rate of 2 mg (NO₃⁻–N) L⁻¹ day⁻¹, which was 3.5 times higher compared with the operation without catalyst. Nitrate was reduced to nitrite and ammonia in the liquid phase at a ratio of 0.6% and 51.8% of the total nitrate amount. These results suggest that nitrate can be successfully used as an oxidant for power generation without aeration and also nitrate removal from water in MFC. However, control of the process would be needed to reduce nitrate to only nitrogen gas, and avoid further reduction to ammonia.     

The Ethanol Tolerance of <Emphasis Type="Italic">Pachysolen tannophilus</Emphasis> in Fermentation on Xylose

The influence of ethanol on fermentation by Pachysolen tannophilus was studied. When xylose utilization rate was 80%, ethanol concentration began to decline. Fermentation of P. tannophilus was affected by ethanol addition in the beginning of fermentation; average xylose consumption rate was 0.065 g·l⁻¹·h⁻¹, and maximum specific growth rate was 0.07 h⁻¹ at 28 g·l⁻¹ ethanol, comparing with the average xylose consumption rate of 0.38 g·l⁻¹·h⁻¹ and maximum specific growth rate of 0.14 h⁻¹ in fermentation with no ethanol addition; P. tannophilus stopped growth at 40 g·l⁻¹ ethanol. When the initial ethanol concentration was 30 g·l⁻¹, the addition of glucose in xylose media made the growth of P. tannophilus better, and the most favorable glucose concentration was 15 g·l⁻¹ with the highest biomass of 1.51 g·l⁻¹ as compared with that of 0.95 g·l⁻¹ in pure xylose media.     

The influence of vegetable oils on biosurfactant production by Serratia marcescens

The production of biosurfactant, a surface-active compound, by two Serratia marcescens strains was tested on minimal culture medium supplemented with vegetable oils, considering that it is well known that these compounds stimulate biosurfactant production. The vegetable oils tested included soybean, olive, castor, sunflower, and coconut fat. The results showed a decrease in surface tension of the culture medium without oil from 64.54 to 29.57, with a critical micelle dilution (CMD⁻¹) and CMD⁻² of 41.77 and 68.92 mN/m, respectively. Sunflower oil gave the best results (29.75 mN/m) with a CMD⁻¹ and CMD⁻² of 36.69 and 51.41 mN/m, respectively. Sunflower oil contains about 60% of linoleic acid. The addition of linoleic acid decreased the surface tension from 53.70 to 28.39, with a CMD⁻¹ of 29.72 and CMD⁻² of 37.97, suggesting that this fatty acid stimulates the biosurfactant production by the LB006 strain. In addition, the crude precipitate surfactant reduced the surface tension of water from 72.00 to 28.70 mN/m. These results suggest that the sunflower oil’s linoleic acid was responsible for the increase in biosurfactant production by the LB006 strain.     

N-functionalized cyclam based trinuclear copper(II) complexes: electrochemical,magnetic, catalytic and antimicrobial studies

A series of trinuclear Cu(II) complexes have been prepared by Schiff base condensation of 1,8-[bis(3-formyl-2-hydroxy-5-methyl)benzyl]-l,4,8,11-tetraazacyclotetradecane and 1,8-[bis(3-formyl-2-hydroxy-5-bromo)benzyl]-l,4,8,11-tetraazacyclotetradecane with aromatic and aliphatic diamines, Cu(II) perchlorate and triethylamine. The complexes were characterized by elemental and spectroscopic analysis. Electrochemical studies of the complexes in DMF solution show three irreversible one-electron reduction processes around E_pc ¹ = −0.73 to −0.98 V, E_pc ² = −0.91 to −1.20 V and E_pc ³ = −1.21 to −1.33 V. ESR spectra and magnetic moments of the trinuclear Cu(II) complexes show the presence of antiferromagnetic coupling. The rate constants for hydrolysis of 4-nitrophenylphosphate by the Cu(II) complexes are in the range of 3.33 × 10⁻² to 7.58 × 10⁻² min⁻¹. The rate constants for the catecholase activity of the complexes fall in the range of 2.67 × 10⁻² to 7.56 × 10⁻² min⁻¹. All the complexes were screened for antifungal and antibacterial activity.     

Kinetics of Growth and Enhanced Sophorolipids Production by Candida bombicola Using a Low-Cost Fermentative Medium

In this study, effect of various parameters on sophorolipid (SL) production by the yeast Candida bombicola was investigated for the enhancing of its production by employing L18 orthogonal array design of experiments. At optimum conditions of sugarcane molasses 50 g l⁻¹, soybean oil 50 g l⁻¹, inoculum size 5% (v/v), temperature 30 °C, inoculum age 2 days, and agitation 200 rpm, the yeast produced almost equal amounts of the product in batch shake flasks and in a 3-l fermentor without any pH control (45 and 47 g l⁻¹, respectively). However, the yield increased to 60 g l⁻¹ in the fermentor under controlled pH environment. Time course of SL production, yeast biomass growth, and utilization of sugarcane molasses and soybean oil at these optimized conditions were fitted to existing kinetic models reported in the literature. Estimated kinetic parameters from these models suggested that conventional medium containing glucose can very well be replaced with the present low-cost fermentative medium.     

Iodine determination in food by inductively coupled plasma mass spectrometry after digestion by microwave-induced combustion

Iodine determination in food samples was performed by inductively coupled plasma mass spectrometry (ICP-MS) after digestion by microwave-induced combustion (MIC). Sample masses up to 500 mg of bovine liver, corn starch, milk powder, or wheat flour were completely combusted using the MIC system. Ammonium nitrate (6 mol l⁻¹ solution, 50 μl) was used as an aid for ignition and vessels were charged with 15 bar of O₂. The use of H₂O, 0.9 mmol l⁻¹ H₂O₂, 10 to 50 mmol l⁻¹ (NH₄)₂CO₃ and 56 mmol l⁻¹ tetramethylammonium hydroxide was investigated as absorbing solutions, as well as the suitability of performing a reflux step after the combustion process. Digestion of food samples by pressurized microwave-assisted acid digestion, microwave-assisted extraction and conventional extraction of iodine in alkaline solution were also evaluated. Iodine recoveries higher than 99% were obtained using MIC and 50 mmol l⁻¹ (NH₄)₂CO₃ or 56 mmol l⁻¹ tetramethylammonium hydroxide as absorbing solution and with 5 min for the reflux step. Accuracy was evaluated using certified reference materials (bovine muscle, corn bran, and milk powder) and agreement better than 97% was obtained. The limit of quantification by MIC and further ICP-MS determination was 0.002 μg g⁻¹. Blanks were always low and no memory effects were observed. Digestion by MIC allowed the processing of up to eight samples by each run in 25 min with high efficiency of digestion (residual carbon content lower than 1%) providing a suitable medium for further iodine determination by ICP-MS.