Multi-Edge-Written Long-Period Fibre Gratings with Low PDL by Using High-Frequency CO2 Laser Pulses

A novel long-period fibre grating （LPFG） with low polarization-dependent loss （PDL） is fabricated by using a multi-edge exposure method with high frequency CO2 laser pulses. The experimental results show that the PDL of a triple-edge-written LPFG with a peak amplitude of-16.5 dB can be as low as 0.22 dB. These hovel LPFGs can find important applications in optical communication and sensing.     

High-Flexible Single-Polarization Single-Mode Photonic-Crystal Fibre

We propose a new type of high flexible single-polarization single-mode (SPSM) photonic crystal fibre (PCF). Numerical analysis indicates that the SPSM PCF proposed guides only one polarization mode over a wavelength band broader than the conventional SPSM fibres. The position and the bandwidth of the single polarization mode region depend flexibly on the structure parameters such as the hole diameters d₁ and d₂ and the hole pitch Λ of the SPSM PCFs. A 200-nm SPSM region can be obtained for the SPSM PCF with Λ=2.55μm, d₁/Λ=0.3 and d₂/Λ=0.833 and the modal birefringence at the wavelength 1.31μm can reach 1.8×10^-3.     

Chaotic Oscillator in Frequency by Using Tunable Laser with Fibre Bragg Grating

A novel chaotic oscillator in wavelength domain by using a tunable fibre laser is proposed. The generator of chaos in wavelength is composed of fibre Bragg grating （FBG） with hybrid delayed feedback loop which induces wavelength nonlinearity. The dynamical regime of wavelength is ruled by a differential difference equation. We give the numerical simulation of the experimental setup and discuss its application in an optical encryption system.     

Highly Birefringent Honeycomb Photonic Bandgap Fibre

A new structure of highly birefringent honeycomb photonic bandgap fibres （PBGFs）, including an elliptical air hole in its solid core, is proposed and analysed by using full vectorial plane wave expansion method. From the numerical results it is confirmed that the proposed PBGF. has birefringence of the order of 10^-3. Moreover, there are two single-polarization single-mode ranges at varying normalized wavelength, in one of which only the slowaxis mode exists, and in the other only the fast-axis mode exists, which has not been achieved in index-guiding photonic crystal fibres so far.     

A Wide-Band Thulium-Doped Silica Fibre Amplifier

We investigate a silica-based thulium-doped fibre amplifier, which is a promising candidate for an amplifying device in the S band, in detail using a single wavelength upconversion pumping scheme centred at 1064nm. Our experimental results show that in terms of gain and noise figure, the bi-directional pumping scheme is the best one in the three pumping schemes, named forward, backward and hi-directional pumping schemes. The amplifier has a gain not only in the S band, but also in the C band, even in the L band. The gain is above 3dB from 1525nm to 1580nm with a peak of 7.SdB.     

Experimental Investigation of High Power Erbium-Ytterbium Co-doped Double Clad Fibre Laser

All-fibre high power erbium-ytterbium co-doped double clad fibre lasers are proposed and demonstrated. By using different back-cavity mirrors, the different double clad fibre lasers are constructed. It is experimentally found that the output behaviour of laser can be controlled by a back-cavity mirror. The lower the reflectivity of the back-cavity mirror, the higher the output power and the high the slop efficiency. The maximum output power is about 1.6 W and the slop efficiency is 27.6%.     

Polarization State Evolution in Fibre Polarization Transformer Influenced by Phase Difference

In accordance with the intrinsic structure of controllably-spun birefringent-fibre-based fibre polarization transformer （FPT）, the Jones vector is calculated from point to point along the polarization transforming fibre by the cascade differential phase retarder model. It is the first time using this concise method to examine the phasedifference effect on the evolution of state of polarization （SOP） inside this special fibre component. Both the extinction ratio and orientation angle of SOP are calculated to give out a whole evolution history from linear polarization light at the slow spun end into circular polarization light at the fast spun end, and vice versa. The influence of phase-difference is discussed on the polarization transforming performance and further referential conclusion is provided for design and test of the FPT component.     

All-Fibre Ytterbium-Doped Photonic Crystal Fibre Laser with High Efficiency

A double-cladding ytterbium-doped photonic crystal fibre （PCF） with a 350-μm^2 effective area is fabricated. The measurement results show that the PCF has high absorption peak at 915 nm. Its fluorescence lifetime is 840μs. Laser experiments with all-fibre configurations are carried out with this fibre. A continuous-wave output power of 3.96 W is achieved with a 5.2 W launched pump power. The central wavelength of the output spectrum is 1080.22nm. The results show that the PCF laser has a high slope efficiency of 79.6% and light conversion efficiency of 76.2%.     

PDL-Compensated Mechanically Induced Long-Period Grating for EDFA Gain Flattening

We present and demonstrate a polarization-insensitive mechanically induced long-period fiber grating (MLPG) for EDFA gain flattening. By forming a 90° fiber rotator in the middle of the MLPG the PDL of the MLPG was substantially reduced. The PDL-compensated MLPG was able to flatten the ASE spectrum of an EDFA successfully without deterioration of the polarization characteristics.     

PDL-Compensated Mechanically Induced Long-Period Grating for EDFA Gain Flattening

We present and demonstrate a polarization-insensitive mechanically induced long-period fiber grating (MLPG) for EDFA gain flattening. By forming a 90° fiber rotator in the middle of the MLPG the PDL of the MLPG was substantially reduced. The PDL-compensated MLPG was able to flatten the ASE spectrum of an EDFA successfully without deterioration of the polarization characteristics.     

Influence of Non-uniform Temperature Field on Spectra of Fibre Bragg Grating

We simulate the spectrum characteristics of fibre Bragg grating （FBG） with non-uniform temperature using the transmission matrix method, and the results are analysed. It is found that firstly the modulated coefficient of average refractive index is a very important parameter that influences the spectrum characteristic of the fibre Bragg grating, and secondly the spectrum curves are different in different temperature fields at the same parameter. Hence, we can determine the metrical temperature by analysing the spectrum of fibre Bragg grating.     

长周期光纤光栅的透射光谱特征

用Matlab编程的方法对长周期光纤光栅的透射光谱谱线特性进行了研究,数值模拟了长周期光纤光栅周期对光谱谱线的影响.研究结论为长周期光纤光栅的设计提供了理论依据.     

Temperature-Insensitive Fibre-Optic Acceleration Sensor Based on Intensity-Referenced Fibre Bragg Gratings

A temperature-insensitive acceleration sensor using two fibre Bragg gratings （FBGs）, based on reflection spectrum intensity modulation and optical power detection, is proposed and demonstrated. A cantilever beam is used to generate acceleration-induced axial strain along two sensing gratings, which are glued on the two opposite surfaces of the beam. Because the two gratings operate within the linear spectral range of a light source, formed by a thermally-tunable extrinsic Fabry-Perot optical filter, the intensity difference of the two reflections from the gratings is proportional to the acceleration applied. This eliminates the need for sophisticated wavelength interrogation of the gratings, and it also endows the sensor with immunity to temperature variation. Compared with a commercial micromachined accelerometer, the sensor is proven to be capable of accurately detecting acceleration.     

Flat Supercontinuum Generation at 1550 nm in a Dispersion-Flattened Microstructure Fibre Using Picosecond Pulse

The generation of a flat supercontinuum of over 80nm in the 1550nm region by injecting 1.6ps 10 GHz repetition rate optical pulses into an 80-m-long dispersion-flattened microstructure fibre is demonstrated. The fibre has small normal dispersion with a variation smaller than 1.5 （ps·nm^-1·km^-1） between 1500 and 1650nm. The generated supercontinuum ranging from 1513 to 1591 nm has the flatness of ±1.5 dB and it is not so flat in the range of several nanometres around the pump wavelength 1552nm. Numerical simulation is also used to study the effect of optical loss, fibre parameters and pumping conditions on supercontinuum generation in the dispersion-flattened microstructure fibre, and can be used for further optimization to generate flat broad spectra.     

S-Band Gain-Flattened Double-Pass Discrete Fibre Raman Amplifiers Using Mechanically Induced Long-Period Fibre Gratings

We experimentally demonstrate an S-band double-pass （DP） discrete fibre Raman amplifier （FRA） gain-flattened by using a mechanically induced long-period fibre grating （LPFG）. Due to a photo-elastic effect in the fibre and its peak loss, the wavelength and depth of the mechanically induced LPFG are continuously regulated by varying the pressures, the angle of the fibre on the graphite rods which are used to produce the periodical pressures along the fibre, the number and the diameter of the graphite rods. Using this gain flattening filter, the gain profile of the DP-FRA is flattened to within ±0.8 dB in the wavelength range from 1485 nm to 1525 nm.     

Thermal Diffusion Process Estimation for Fabrication of Graded Plastic Optical Fibre

Thermal diffusion of dopants is investigated in the process of generating the graded-index profile of plastic optical fibres. Because the diffusion coefficient in high polymers has been shown to depend strongly on dopant concentration, it is allowed in this work to vary with the radial coordinate of the multistep-core fibre. A novel multi-layer model is presented for solving the diffusion equation with the variable diffusion coefficient. It is solved by the finite difference method. The solution determines the dopant diffusion profile in the fibre. It is verified against a solution from the literature and two cases of fibres with diffused profiles. The application is demonstrated on two examples of graded-index plastic optical fibres, one originally with a two-step and the other with four-step core. The results indicate that closer to the core-cladding interface, the computed diffused profile with variable diffusion coefficient D is closer to target profile than the profile obtained with constant D for the same time of thermal process.     

Estimation of the fibre temperature during the inscription of arc-induced long-period gratings

The underlying formation mechanisms and the properties of long-period gratings produced through arc discharges are intrinsically related to the temperature reached by the fibre during arc exposure. In this work, the determination of the fibre temperature was based on Plank’s blackbody radiation law. The radiation emitted by the optical fibre during heating due to an electric arc discharge, detected using a Cronin spectrometer, was fitted to the emission spectrum of the blackbody radiation, allowing the estimation of the temperature range attained by the fibre. A peak temperature of 1400 ± 50 °C was obtained.     

Transmission Bandwidth Tunability of a Liquid-Filled Photonic Bandgap Fiber

A temperature tunable photonie bandgap fiber （PBGF） is demonstrated by an index-guiding photonic crystal fiber filled with high-index liquid. The temperature tunable characteristics of the fiber are experimentally and numerically investigated. Compression of transmission bandwidth of the PBGF is demonstrated by changing the temperature of part of the fiber. The tunable transmission bandwidth with a range of 250nm is achieved by changing the temperature from 30℃ to 90℃.     

Fibre Optical Parametric Amplification in Defect Bragg Fibres with Zero Dispersion Slow Light Effect

Nonlinearity enhancement by slow light effect and strong light confinement in defect Bragg fibres is demonstrated and anMysed in applications of fibre optical parametric amplifiers. Broadband low group velocity and zero dispersion as well as the strong light confinement by band gap enhances the nonlinear coefficient up to more than one order than the conventional high nonlinear fibres. Moreover, the zero dispersion wavelength of coupled core mode can be designed arbitrarily, under which the phase-matching bandwidth of the nonlinear process can be extended.     

A Distributed Fibre Bragg Grating Sensor Interrogator Employing a Reformative Arrayed Waveguide Grating

We present an interrogating technique employing a reformative arrayed waveguide grating without output waveguides in combination with a linear charge coupled device. A simple and effective data processing method called area equalized point is used to improve the system resolution. The simulation results show that the wavelength shift of a fibre Bragg grating with temperature can be precisely measured by this interrogation technique. The temperature accuracy and wavelength resolution of the sensor system are smaller than 0.08℃ and 0.8pm, respectively. If the FBG 3dB-bandwidth is 0.2nm with the wavelength spacing between two adjacent FBGs of 1.4 nm, the temperature and wavelength errors caused by crosstalk are respectively 0.01℃ and 0. 1 pm.