Cubic BN Sintered with A1 under High Temperature and High Pressure

Sintering of cubic boron nitride （cBN） with addition of A1 is carried out in the temperature range 1300-1500℃ and under the pressure 5.5 GPa. When sintered at 1300℃, a weak diffractive peak of hexagonal BN （hBN） is observed in the Al-cBN sample, indicating the transformation from cBN to hBN. No nitrides or borides of A1 are observed, which indicated that A1 does not react with cBN obviously. When the sintering temperature is increased to 1400℃, the diffractive peak of hBN disappears and new phases of A1N and A1B2 are observed, due to reactions between A1 and cBN. When the sintering temperature is further increased to 1500℃, the contents of A1N and A1B2 phases increase and the A1 phase disappears completely.     

Surface Structure of Large Synthetic Diamonds by High Temperature and High Pressure

With NiMnCo and FeCoNi alloys as solvent metals, large single-crystal diamonds of about 3mm across are grown by temperature gradient method （TGM） under high temperature and high pressure （HPHT）. Although both {100} and {111} surfaces are developed by a layer growth mechanism, some different characteristic patterns are seen clearly on the different surfaces, no matter whether NiMnCo or FeCoNi alloys are taken as the solvent metals. For {100} surface, it seems to have been melted or etched greatly, no dendritic patterns to be found, and only a large number of growth hillocks are dispersed net-likely; while for {111} surface, it often seems to be more smooth-faced, no etched or melted traces are present even when a lot of depressed trigonal growth layers. This distinct difference between {111} and {100} surfaces is considered to be related to the difference of surface-atom distribution of different surfaces, and {111} surfaces should be more difficult to be etched and more steady than {100} surfaces.     

高质量高效率参量光的获得

分析了泵浦光为光强在时空上不均匀和高度有限性分布的高斯光波时，对光学参量发生过程的不利影响，提出了解决这种不利影响，以获得高质量，高效率参量光的方案。     

Stable High Power and High Beam Quality Diode-Side-Pumped Continuous-Wave Intracavity Frequency-Doubled Nd:YAG Laser

We report a stable high power and high beam quality diode-side-pumped cw green laser from intracavity frequency-doubled Nd： YAG laser with KTP. By using a L-shaped concave-convex resonator, designed with two Nd：YAG rods birefringence compensation, a large fundamental mode size in the laser crystal and a tight focus in the nonlinear crystal could be obtained simultaneously. The green laser delivers a maximum 532nm output power of 23.2 W. Under 532nm output power of 20.9 W, the beam quality factor is measured to be 4.1, and the fluctuation of the output power is less than 1.4% in an hour.     

In Situ Raman Spectroscopy Study on Dissociation of Methane at High Temperatures and at High Pressures

We investigate the stability and dissociation of methane, which is the most abundant organic molecule in the universe, using diamond anvil cell （DAC） with in situ Raman spectroscopy up to 903K and 21 GPa. At the temperatures of 793 and 723 K and the corresponding pressures of 16.15 and 20.30 GPa, methane dissociates to form carbon ＇soot＇ and heavier hydrocarbons involving C=C and C≡C bonds. However, if the pressure is not very high, methane remains stability up to the highest temperature of 903 K of the work. The four symmetric C-H bonds of methane split at high temperatures and at high pressures, and there is at least one phase transition of crystalline symmetry from face centred cubic （fcc） to hexagonal close packed （hcp） before dissociation.     

Hetero-Epitaxial Diamond Single Crystal Growth on Surface of cBN Single Crystals at High Pressure and High Temperature

We report a new diamond synthesis process in which cubic boron nitride single crystals are used as seeds, FesoNi20 alloy powder is used as catalyst/solvent and natural flake-like graphite is used as the carbon source. The samples are investigated using laser Raman spectra and x-ray diffraction （XRD）. Morphology of the sample is observed by a scanning electron microscope （SEM）. Based on the measurement results, we conclude that diamond single crystals have grown on the cBN crystal seeds under the conditions of high temperature 1230℃ and high pressure 4.8 GPa. This work provides an original method for synthesis of high quality hereto-semiconductor with cBN and diamond single crystals, and paves the way for future development.     

Raman Scattering Spectroscopy of Phase Transition in n-Pentadecane under High Temperature and High Pressure

The Raman spectroscopy of n-pentadecane is investigated in a moissanite anvil cell at normal temperatures and a diamond anvil cell under pressure to about 3000MPa and at temperature from 298 to 573K. Result indicates that at room temperature the vibration modes, assigned to the symmetric and asymmetric stretching of CH3 and CH2 stretching, shift to higher frequency and display a pressure dependent quasi-linear curve. A liquid-solid phase transition appears at a pressure of 150 MPa. The high temperature solidus line of n-pentadecane follows a quadratic function of P = 0.02369T^2 - 9.117T ＋ 725.58, in agreement with previous conclusion derived from studies of other hydrocarbons. Upon phase transition, fitting the experimental data obtained in a temperature range of 283 553 K to the Clausius-Clapeyron equation allows one to define the thermodynamic parameters of n-pentadecane of dP/dT = 0.04738T - 9.117.     

Effects of NaN3 Added in Fe-C System on Inclusion and Impurity of Diamond Synthesized at High Pressure and High Temperature

Effects of NaN3 added in Fe-C system to synthesize nitric diamond at high pressure and high temperature are investigated. Diamond crystals with high nitrogen concentration are synthesized by the system of Fe-C and NaN3 additive at pressure 5.8 GPa and at temperatures 1750-1780 K for 15 min. The synthetic diamond crystals have a cubo-octahedral or octahedral shape with yellowish green or green colour. Some disfigurements are observed on the surfaces of most diamond crystals. The composition and content of inclusions formed by iron in diamond are changed and iron nitride is detected in diamond crystals synthesized with Fe-C-NaN3 additive. As the amount of NaN3 additive increases, Fe3C decreases and iron nitride increases with α-Fe being nearly constant. Moreover, the nitrogen concentrations in diamond crystals synthesized with 1.5 wt% NaN3 additive is up to 2250ppm in substitutional form.     

High Field Seeking State Atom Laser and Properties of Flux

We present an experimental study on the continuous atom laser. The experiments show that a high field seeking state atom laser with stable flux can be formed by increasing the strength of outcoupling before large density fluctuations appear. It is easy to obtain a long length or high speed output with this kind of atom laser.     

High pressure phase transition and elastic properties of thorium chalcogenides

The structural and elastic properties of thorium chalcogenides at high pressure, have been investigated using a suitable inter-ionic potential. The calculated equation of state, phase transition pressures for B1-B2 transition and bulk moduli for ThX (X=S,Se,Te) compounds agree well with the experimental results. ThTe, which crystallizes in the CsCl structure, does not show any structural transition up to 48 GPa. The present analysis does not show any anomalous features in elastic properties arising from ‘f’ electrons.     

High resolution microwave spectroscopy of the isomeric pair vinylcyanoacetylene and cyanovinylacetylene

The carbon chain molecules vinylcyanoacetylene and cyanovinylacetylene have been investigated between 8 and 41 GHz by Fourier transform microwave spectroscopy of a supersonic molecular beam. Owing to the high spectral resolution of the present technique, significantly more accurate rotational and centrifugal distortion constants have been derived for both molecules. In addition, the dipole moments have been calculated at the B3LYP/cc-pVTZ level of theory. Because these carbon chains are similar in structure and composition to known astronomical molecules and because of their high polarity, both species are good candidates for radioastronomical detection.     

Integratable and High Speed Complex-Coupled MQW-DFB Lasers Fabricated on Semi-Insulating Substrates

A novel integratable and high speed InGaAsP multi-quantum well （MQW） complex-coupled distributed feedback （DFB） laser is successfully fabricated on a semi-insulating substrate. The fabricated ridge DFB laser exhibits a threshold current of 26 mA, a slope efficiency of 0. 14 W·A^-1 and a side mode suppression ratio of 40 dB together with a 3 dB bandwidth of more than 8 GHz. The device is suitable for 10 Gbit/s optical fiber communication.     

High sensitive measurements of absorption coefficient and optical nonlinearities

Accurate knowledge of absorption coefficient of a sample is a prerequisite for measuring the third-order optical nonlinearity of materials, which can be a serious limitation for unknown samples. We introduce a method, which measures both the absorption coefficient and the third-order optical nonlinearity of materials with high sensitivity in a single experimental arrangement. We use a dual-beam pump-probe experiment and conventional single-beam z-scan under different conditions to achieve this goal with communication relevant wavelength. We also demonstrate a counterintuitive coupling of the non-interacting probe-beam with the pump-beam in pump-probe z-scan experiment.     

High refractive index and transparent heavy metal oxide glassy thin films

Heavy metal oxide thin films of the ternary system Nb₂O₅–GeO₂–PbO have been prepared by pulsed laser deposition in an O₂ environment from either glassy or crystalline bulk samples. The range of ([Pb]+[Nb]) content in which the films are optically homogeneous and transparent is much broader (0.5–1.0) than that of the bulk samples considered in the present work (0.55–0.62). The imaginary part of the refractive index is very low in all cases (k<10^-3), whereas the real part increases linearly with the ([Pb]+[Nb]) content up to values as high as 2.35. The optical energy gap has been found to be strongly dependent on [Pb], whereas it is almost independent of [Nb]. This dependence is discussed in terms of the role of Pb and Nb as network modifiers or formers. Received: 5 August 2002 / Accepted: 8 August 2002 / Published online: 17 December 2002 RID="*" ID="*"Corresponding author. Fax: +34-91/564-5557, E-mail: j.gonzalo@io.cfmac.csic.es     

High Power Photonic Crystal Fibre Raman Laser

A cw Raman laser based on a 100-m photonic crystal fibre is demonstrated with up to 3.8 W output power at the incident pump power of 12 W, corresponding to an optical-to-optical efficiency of about 31.6%.. The second order Stokes light, which is firstly reported in a cw photonic crystal fibre Raman laser, is obtained at 1183nm with an output power of 1.6 W and a slope efficiency of about 45.7%.     

High frequency and static dielectric constants of zinc blende structured solids

A correlation is presented for the high frequency ε_∞ and static ε_o dielectric constants of A^IIB^{V I} and A^IIIB^V semiconductors with the zinc blende structure. The high frequency ε_∞ and static ε_o dielectric constants can be represented by an empirical linear relation that is a simple function of melting temperature T_m, atomic volume Ω and product of ionic charges (Z₁Z₂). Values of high frequency ε_∞ and static ε_o dielectric constants of A^IIB^{V I} and A^IIIB^V zinc blende semiconductors exhibit a linear relationship when plotted against the k_BT_m/Ω (k_B=Boltzmann’s constant), but fall on two straight lines according to the product of ionic charges of the compounds. The calculated results are compared with available experimental data and previous calculations based on phenomenological models.     

Realization of High Optical Density Rb Magneto-optical Trap

We report experimental demonstration of a magneto-optical trap （MOT） of Rb atoms with a high optical density. With 2.2-cm-diameter cooling laser beams, we achieve an optical density of nearly 11 for about 2.6× 10^10 trapped Rb atoms with the beam intensity of about 6.6 mW/cm^2 per beam. The temperature of the cold atoms is about 250 μK. Furthermore, by ramping the magnetic field gradient from 8 G/cm to about 20 G/cm, the atomic cloud in the MOT is compressed and the optical density is up to 16.     

High temperature-pressure processing of mixed alanate compounds

Mixtures of light-weight hydrides and elements were investigated to increase the understanding of the chemical reactions that take place between various materials. This report details investigations we have made into mixtures that include NaAlH₄, LiAlH₄, MgH₂, Mg₂NiH₄, alkali(ne) hydrides, and early third row transition metals (V, Cr, Mn). Experimental parameters such as stoichiometry, heat from ball milling versus hand milling, and varying the temperature of high pressure molten state processing were studied to examine the effects of these parameters on the reactions of the complex metal hydrides.     

High Polarization Single Mode Photonic Crystal Microlaser

Generally, dipole mode is a doubly degenerate mode. Theoretical calculations have indicated that the single dipole mode of two-dimensional photonic crystal single point defect cavity shows high polarization property. We present a structure with elongated lattice, which only supports a single y-dipole mode. With this structure we can eliminate the degeneracy, control the lasing action of the cavity and demonstrate the high polarization property of the single dipole mode. In our experiment, the polarization extinction ratio of the y-dipole mode is as high as 51：1.     

Ductile Bulk Aluminum-Based Alloy with Good Glass-Forming Ability and High Strength

Based on a new approach for designing glassy alloy compositions, bulk Al-based alloys with good glass-forming ability （GFA） are synthesized. The cast Al86Si0.5Ni4.06Co2.94 Y6Sc0.5 rod with a diameter of i mm shows almost fully amorphous structure besides about 5% fcc-Al nucleated in the center of the rod. The bulk alloy with high Al concentration exhibits an ultrahigh yield strength of 1.18 GPa and maximum strength of 1.27 GPa as well as an obvious plastic strain of about 2.4% during compressive deformation. This light Al-based alloy with good GFA and mechanical properties is promising as a new high specific strength material with good deformability.