SEM and AES depth profile studies of thin titanium and titanium oxide films covered by nanoscale evaporated Au layers

Thin titanium and titanium oxide films, both covered by ultra-thin gold layers, have been compared with titanium films after analysis, using a combination of SEM and AES. The Ti films were prepared under UHV conditions by evaporation on a glass substrate. The Ti oxide layers were prepared in situ by precisely controlled oxygen sorption at 298 K on Ti film. Both Ti and Ti oxide films were then covered in situ by a very thin Au layer. Analysis was performed in a separate system after long-term exposure of the films to air. SEM analysis revealed a much smaller size grain on the Au coated Ti films than on Ti films not coated with a Au layer. The thin gold layers covering the Ti surface prevent an extensive air interaction with Ti film. The analysis of the features of the Ti Auger spectra during the sputter profile measurements allow to characterise the chemical nature of Ti-oxide formed in Ti/Au interface region. Received: 7 September 1998 / Revised: 14 January 1999 / Accepted: 2 February 1999     

3-methylthiophene self-assembled monolayers on planar and nanoparticle Au surfaces

In this article the adsorption of 3-methylthiophene on planar and nanoparticle Au surfaces is investigated. The resulting systems are compared with a benchmark system based on 1-decanethiol. The characterization data collected evidence the formation of a packed 3-methylthiophene SAM on the planar surface. In particular, spectroscopic investigations suggest that 3-methylthiophene aromatic system is not adsorbed on the surface through the pi-electron system but rather through the S atom alone. On the other hand, the behavior of 3-methylthiophene on nanoparticle surfaces is notably different from that of the alkanethiol. Only a limited fraction of the surface of Au nanoparticles results to be actually coated after purification; this notwithstanding, the nanoparticle growth seems to be strongly influenced by the presence of such a labile encapsulating agent.     

Preparation and nonlinear optical properties of Au nanoparticles doped TiO2 thin films

Nano-sized noble metal nanoparticles doped dielectric composite films with large third-order nonlinear susceptibility due to the confinement and the enhancement of local field were considered to be applied for optical information processing devices, such as optical switch or all optical logical gates. In this paper, sol–gel titania thin films doped with gold nanoparticles (AuNPs, ~10 nm in average size) were prepared. AuNPs were firstly synthesized from HAuCl₄ in aqueous solution at ~60 °C, using trisodium citrate as the reducing agent, polyvinylpyrrolidone as the stable agent; then the particle size and optical absorption spectra of the AuNPs in aqueous solutions were characterized by transmitting electron microscopy and UV–Vis–NIR spectrometry. Sol–gel 2AuNPs–100TiO₂ (in %mol) thin films (5 layers, ~1 μm in thickness) were deposited on silica glass slides by multilayer dip-coating. After heat-treated at 300–1,000 °C in air, the AuNPs–TiO₂ thin films were investigated by X-ray diffraction, scanning electron microscopy and atomic force microscopy. The nonlinear optical properties of the AuNPs–TiO₂ thin films were measured with the Z-scan technique, using a femtosecond laser (200 fs) at the wavelength of 800 nm. The third-order nonlinear refractive index and nonlinear absorption coefficient of 2AuNPs–100TiO₂ films were at the order of 10^?12 cm²/W, and the order of 10^?6 cm/W, respectively, and the third-order optical nonlinear susceptibility χ⁽³⁾ was ~6.88 × 10^?10 esu.     

Preparation and characterization of sol-gel derived KTiOPO4 thin films for integrated optical applications

A sol gel route has been developed to produce stoichiometric, dense and crack free KTiOPO₄ (KTP) thin films which exhibit waveguiding. This method involved the deposition and pyrolysis of hydrolyzed solutions of K, Ti and P alkoxides on an appropriate substrate. The final ceramic film morphology is greatly dependent on the preparation chemistry, apparently as a result of the formation of polymetallic complexes. The solution chemistry, processing conditions and their influence on the final ceramic film microstructure will be discussed in detail.Optical properties such as indices of refraction and optical losses have been found to be dependent on the film microstructures. Deposition on different substrates has been undertaken to promote preferential orientation and thus to try to minimize the optical losses in the films. This correlation between the optical losses and microstructures will be discussed in detail.     

Structural,morphological and optical studies on chemically deposited nanocrystalline CdZnSe thin films

In the present paper, cadmium zinc selenide (Cd_0.5Zn_0.5Se) thin films were deposited on glass substrates by chemical bath deposition with optimized deposition parameters. 2-mercaptoethanol was used as a capping agent. The as-deposited thin films were annealed at 300, 500 and 700 °C and then subjected to various structural, morphological and optical investigations. The effect of the presence of capping agent and annealing on these properties was discussed. The phenomenon of phase transformation occurred during annealing. The optical band gap energies were found in the range 2.37–1.7 eV with respect to the annealing temperatures.     

Single molecule study of perylene orange photobleaching in thin sol-gel films

The paper reports on photobleaching mechanisms of perylene orange embedded in thin sol-gel films, derived from single molecule studies. The experimental configuration uses wide-field illumination and one photon excitation of the molecules. Measurements have been performed both at ambient conditions and under vacuum in order to get information on the influence of oxygen on photobleaching in such porous samples. We have also recorded the evolution of photobleaching with respect to the excitation intensity. The results demonstrate that photobleaching from excited states higher than the first singlet and triplet states has a nonnegligible contribution as soon as the excitation energy exceeds a few hundred W/cm2 and that this process is favored in the presence of air. The study also demonstrates that perylene orange in sol-gel films is not a very efficient emitter but that photobleaching can be slow, which explains the interest for perylene orange as a good candidate to produce long lifetime solid-state lasers when embedded in monoliths of sol-gel.     

Raman study of oriented ZnO thin films deposited by sol-gel method

ZnO films with preferred orientation along the (0 0 2) plane were successfully deposited by the sol-gel method using Zn(CH3COO)2.2H2O as starting material and inorganic precursor. A homogeneous and stable solution was prepared by dissolving the zinc acetate in a solution of ethanol and monoethanolamine. Thin films are obtained by spin-coating on glass substrates. ZnO films were obtained by preheating the spin-coated films at 300 degrees C for 10 min after each coating and postheating upto 550 degrees C for 2h. The as-deposited films are transformed into mono-oriented ZnO upon thermal treatment. The films consist of spongy particles aggregates with an uniform size and homogenous surface. The films aim to be used in optoelectronic devices. Raman spectroscopy from ZnO films and deposit solutions has been investigated. New Raman results of the deposit solution suggest that Zn-O bond forms first in solution and that these entities play the role of germs initiating the crystallization mechanisms during films annealing. Raman spectra of the annealed films show the presence of a compressive stress within the film structure.     

Electrochemical evidences of morphological transformation in ordered mesoporous titanium oxide thin films

We provide the first electrochemical evidence of permeability changes in continuous mesoporous TiO2 thin film electrodes induced by nanocrystallisation.     

Morphology and optical properties of thin silica films containing bimetallic Ag/Au nanoparticles

We have studied the optical spectra in the UV and visible regions, the morphology by scanning electron microscopy (SEM), and the X-ray photoelectron spectra (XPS) of bimetallic Ag/Au nanoparticles incorporated into transparent silicate films in the sol-gel transition stage. The bimetallic nanoparticles, obtained by a combination of photoreduction and thermal reduction, form structures of the alloy or core-shell type. Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 44, No. 6, pp. 348–353, November–December, 2008.     

A simple route to ordered metal oxide nanoparticle arrays using block copolymer thin films

Oxide nanoparticles arrays are easily synthesized in a 3-steps method including (i) the deposition of poly(styrene)-b-poly(4-vinylpyridine) (PS-b-PVP) thin films, (ii) the selective deposition of inorganic precursors and (iii) the synthesis of oxide nanoparticles and the elimination of the polymer scaffold by thermal annealing. The specific staining of the PVP domains by inorganic precursors is obtained in this study thanks to a simple and fast spin coating process using an alcoholic solution of the precursors. This simple lab-procedure is used to synthesize a wide range of metallic (silicon, titanium, cerium, ruthenium, zinc and manganese) oxides, showing that this method can be extended to the synthesis of all kinds of oxides with all kinds of precursors as long as the precursor is soluble in P4VP solvent. It is shown that this strategy can be extended to the synthesis of oxide nanorods.     

Bismuth sulfide thin films with low resistivity on self-assembled monolayers

Using self-assembled monolayers (SAMs), highly crystalline bismuth sulfide thin films with low electrical resistivity have been prepared from aqueous solution at low temperature (40-70 degrees C). The nucleation and growth process of Bi2S3 thin films was investigated in detail by XPS, AES, SEM, XRD, SAED, and HRTEM. Solution conditions have marked effects on the microstructure, growth rate, and mechanism of Bi2S3 films. Increased solution temperature resulted in a higher growth rate and a shorter induction time due to a higher supersaturation degree. In the solution of pH 1.12, homogeneous nucleation and the attachment process dominated the formation of Bi2S3 films. In contrast, at pH 0.47 Bi2S3 thin films were formed via heterogeneous nucleation and growth. The c-axial orientation of bismuthinite films was enhanced with the increase of reaction time. By controlling the solution supersaturation and reaction duration, highly crystalline Bi2S3 films composed of closely packed and coalescent crystallites could be realized, whose dark electrical resistivity could reach as low as 0.014 Omega cm without any post-treatment.     

Selected-area sol-gel deposition of barium strontium titanate thin films on thermally oxidized silicon through mediation of self-assembled monolayers

Self-assembled monolayers (SAMs) of octadecyltrichlorosilane (OTS) and mercapto ethanol were used to modify the surface functionality of platinum/titanium or platinum/tantalum bilayer patterns on thermally oxidized silicon wafers. The attachment of OTS to the exposed oxide region made it hydrophobic, while the anchoring of mercapto ethanol to the bilayer pattern turned it hydrophilic. This patterned hydrophobicity and hydrophilicity was exploited to preferentially deposit barium strontium titanate (BST) thin films on the patterned bilayers from an aqueous sol-gel solution. The combination of the SAMs and the sol-gel film formation method allowed direct patterned deposition of BST thin films, which could be useful for on-chip electronic applications. Wet oxygen annealing at 50 °C was sufficient to stabilize the deposited sol-gel coating without adversely affecting the functionality of the OTS, thus permitting multiple dip-coatings to obtain patterned films of a desired thickness. Heat treatment at 750 °C allowed densification and conversion of the sol-gel coatings to perovskite BST films.     

The morphological,optical and electrical properties of SnO2:F thin films prepared by spray pyrolysis

Combining the spray pyrolysis and the sol–gel techniques gives the possibility to produce Fluorine doped Tin oxide (SnO₂:F) thin films. Transparent conducting SnO₂:F thin films have been deposited on glass substrates by the spray pyrolysis technique. This technique for the fabrication of SnO₂:F filmsby combining sol–gel process and the spray pyrolysis technique ispresented in this paper. The Sol–gel precursors have been successfully prepared using SnCl₂·5H₂O and (Ac)F₃. The structural, electrical, and optical properties of these films were investigated. The high resolution transmission electron microscopy (HRTEM) and selected area diffraction (SAD) patterns of SnO₂:F films show that the gel films lead to a tetragonal structure. The X‐ray diffraction pattern of the films deposited at substrate temperature 530° , the orientation of the films was predominantly [110]. In addition, the surface chemical components were also examined by X‐ray photoelectron spectroscopy (XPS) showing the SnO₂:F deposited with the atomic concentration ratios Sn/F 1.82:1. The minimum sheet resistance was 50 Ω and average transmission in the visible wavelength range of 300 to 800 nm was 87.25%. Copyright © 2008 John Wiley & Sons, Ltd.     

X-ray and Raman study of spray pyrolysed vanadium oxide thin films

Vanadium oxide thin films were prepared by spray pyrolysis using solutions of vanadium chloride (VCl₃) with different concentrations on glass substrates heated at 200 and 250 °C. The influence of substrate temperature (T_s) and solution concentration (molarity) on structural and vibrational properties is discussed by using X-ray diffraction and Raman spectroscopy. The results revealed that at 0.05 M and T_s = 200 °C, V₄O₉ thin films are obtained. At 250 °C, V₂O₅ phases with preferential orientation are observed and the films become polycrystalline when the molarity increases.     

Surface modification of surface sol-gel derived titanium oxide films by self-assembled monolayers (SAMs) and non-specific protein adsorption studies

Biological events occurring at the implant-host interface, including protein adsorption are mainly influenced by surface properties of the implant. Titanium alloys, one of the most widely used implants, has shown good biocompatibility primarily through its surface oxide. In this study, a surface sol-gel process based on the surface reaction of metal alkoxides with a hydroxylated surface was used to prepare ultrathin titanium oxide (TiOx) coatings on silicon wafers. The oxide deposited on the surface was then modified by self-assembled monolayers (SAMs) of silanes with different functional groups. Interesting surface morphology trends and protein adhesion properties of the modified titanium oxide surfaces were observed as studied by non-specific protein binding of serum albumin. The surface properties were investigated systematically using water contact angle, ellipsometry, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) measurements. Results showed that the surface sol-gel process predominantly formed homogeneous, but rough and porous titanium oxide layers. The protein adsorption was dependent primarily on the silane chemistry, packing of the alkyl chains (extent of van der Waals interaction), morphology (porosity and roughness), and wettability of the sol-gel oxide. Comparison was made with a thermally evaporated TiOx-Ti/Si-wafer substrate (control). This method further extends the functionalization of surface sol-gel derived TiOx layers for possible titanium alloy bioimplant surface modification.     

Fe(CO)5 thin films adsorbed on Au(111) and on self-assembled organic monolayers: I. Structure

The adsorption of Fe(CO)(5) onto Au(111)/mica and C(4), C(8), C(12), and C(16) SAMs/Au(111)/mica surfaces has been studied using infrared spectroscopy to elucidate the coverage-dependent structures of these films and the intermolecular couplings that determine the form of the spectra. For all substrates, the first layer is composed of molecules physisorbed with one axial and two equatorial carbonyl groups directed toward the substrate; subsequent layers are preferentially oriented with the C(3) molecular axis aligned perpendicular to the substrate (i.e., one axial carbonyl group directed toward the substrate). The axial vibrational band systematically shifts to higher frequencies with increasing surface coverage because of the effects of intermolecular coupling of the quasiparallel transition dipole moments. The strong effects of dipolar coupling are also witnessed by the trends of the band positions when the distance to the image plane is systematically varied using highly organized self-assembled organic substrates; no band shifts are observed when dilute Fe(CO)(5) is embedded in Xe matrixes under identical experimental conditions. The as-deposited films are structurally stable below 125 K on Au(111)/mica surfaces and below 100 K on the organic self-assembled monolayers. The instability of the films above these temperatures demonstrates that the as-adsorbed films do not form thermodynamically well-defined phases but are structurally metastable. The results presented herein and in the companion paper provide a consistent framework to interpret the spectroscopy of these systems that resolves outstanding issues concerning these films and provides a structural model that explains the dynamic properties of these films during exposure to low-energy electron beams.     

Electronic transport and optical properties of indium oxide thin films prepared by thermal oxidation

Indium oxide (In₂O₃) thin films were prepared using thermal oxidation of metallic films. Indium metallic thin films were deposited onto glass substrates, by vacuum thermal evaporation. Optical and electronic transport properties of thermally oxidized In₂O₃ films were investigated and these properties were correlated with their preparation conditions, more exactly with oxidation temperatures (T_ox = 623 K, 673 K and 700 K, respectively). Structural analysis, investigated by X-ray diffraction and electron diffraction, reveals that the obtained films possess a polycrystalline structure. The temperature dependence of electrical conductivity was studied using surface-type cells with Ag electrodes. The electronic transport mechanism, in respective films, is discussed in terms of crystallite boundary trapping, proposed by Seto. Some characteristic parameters such as energy barrier, impurity concentration, distribution of interface states, were determined. Transmission and reflection spectra were recorded and by using the values of these coefficients, some optical parameters were calculated (absorption coefficient, optical band gap, refractive index).     

Structural,morphological, optical and third order nonlinear optical response of spin-coated NiO thin films: An effect of N doping

The present work deals with the deposition of NiO and Nitrogen (N)-doped NiO thin films by sol-gel spin coating technique. Structural, morphological, linear and non-linear optical characteristics of undoped and N-doped (1–15 wt%) NiO films were studied. From XRD measurements, it is evident that single phase nano crystalline NiO is formed for all doping concentrations. Surface morphology study shows that higher concentration of N doped NiO thin films were of high quality and EDX mapping confirmed the doping of Nitrogen in films. The Raman spectra of the studied films were analyzed over the range of 1400-200 cm⁻¹. The optical studies confirm that as doping increases, transparency of the film decreases (except at 10% N doping) and the band gap narrows. Nonlinear parameters such as refractive index and susceptibilities also depend on N dopant concentration. Z-scan studies viz., absorption index, nonlinear refractive index were carried out on undoped and N doped NiO samples and the results were matched with theoretical calculated values.     

Effect of potassium permanganate on morphological,structural and electro-optical properties of graphene oxide thin films

This work investigated the effect of Potassium Permanganate (KMnO₄) on graphene oxide (GO) properties, especially on electrical properties. The GO thin films were deposited on a glass substrate using drop casting technique and were analysed by using various type of spectroscopy (e.g. Scanning Electron Microscopy (SEM), Ultra- Violet Visible (UV–VIS), Fourier Transform Infrared (FTIR), X-Ray Diffraction (XRD), optical band gap, Raman Spectroscopy). Furthermore, the electrical experiments were carried out by using current–voltage (I-V) characteristic. The GO thin film with 4.5 g of KMnO₄ resulted in higher conductivity which is 3.11 × 10^?4 S/cm while GO with 2.5 g and 3.5 g of KMnO₄ achieve 2.47 × 10^?9 S/cm and 1.07 × 10^?7 S/cm, respectively. This further affects the morphological (SEM), optical (band gap, UV–Vis, FTIR, and Raman), and crystalline structural (XRD) properties of the GO thin films. The morphological, elemental, optical, and structural data confirmed that the properties of GO is affected by different amount of KMnO₄ oxidizing agent, which revealed that GO can potentially be implemented for electrical and electronic devices.     

Fe(CO)5 thin films adsorbed on Au(111) and on self-assembled organic monolayers: II. Thermal transformations

The thermal transformations of as-deposited Fe(CO)(5) films adsorbed on Au(111)/mica and C(4), C(8), C(12), and C(16) self-assembled methyl-terminated monolayer organic surfaces have been studied using infrared spectroscopy to probe how the physical restructuring influences the sensitivity of these systems to low-energy electron beams. A companion publication shows that the as-deposited monolayers are composed of molecules physisorbed with one axial and two equatorial carbonyl groups directed toward the substrate; subsequent layers are preferentially oriented with the C(3) molecular axis aligned perpendicular to the substrate (i.e., one axial carbonyl group directed toward the substrate). In this work, we show that the as-deposited films are structurally unstable above 125 K on Au(111)/mica surfaces and above 100 K on the organic self-assembled monolayers. Above these thresholds, the layered structures transform into three-dimensional aggregates, implying strongly nonwetting behavior for Fe(CO)(5) on each of these substrates; molecular desorption from this aggregate structure takes place between 140 and 160 K. The irreversibility of this temperature-induced transformation demonstrates that the as-deposited layered films do not represent a thermodynamically well-defined phase; this key feature of the as-deposited films is believed to be the cause of the discrepancies in previous attempts to understand Fe(CO)(5)/surface structures based on infrared results. Moreover, the thermally induced transformation to 3D aggregate structures is shown to decrease the apparent sensitivity of the adsorbed Fe(CO)(5) to low-energy electron-induced decarbonylation (0-10 eV) by over 3 orders of magnitude.