Pt微粒修饰纳米纤维聚苯胺电极对甲醇氧化电催化

以脉冲电流法制备的纳米纤维状聚苯胺(PANI)为Pt催化剂载体，用它制备了甲醇阳极氧化的催化电极Pt/（nano-fibular PANI）.研究结果表明, Pt/（nano-fibular PANI）电极对甲醇氧化具有很好的电催化活性,并有协同催化作用.在相同的Pt载量条件下， Pt/（nano-fibular PANI）电极比Pt微粒修饰的颗粒状聚苯胺电极Pt/(granular PANI)具有更好的电催化活性.此外， Pt的电沉积修饰方法同样影响Pt/（nano-fibular PANI）电极对甲醇氧化的催化活性.脉冲电流法沉积Pt形成的复合电极较循环伏安法电沉积得到的Pt复合电极具有更优异的催化活性.     

电催化甲酸氧化中钯微粒与聚苯胺的相互作用

采用电化学、ＸＰＳ和拉曼光谱研究钯微粒修饰聚苯胺（ＰＡＮ（Ｐｄ）电极对甲酸氧化的电催化行为。由于钯与ＰＡＮ的相互作用，钯微粒在所研究的电位区间可稳定地固定于ＰＡＮ中，且甲酸在钯上的氧化明显地抑制ＰＡＮ的氧化降解，使ＰＡＮ（Ｐｄ）电极电催化甲酸氧化反应具有高的稳定性和活性。     

铂修饰超细纤维聚苯胺在葡萄糖生物传感方面的应用

在不锈钢电极(SS)表面制得超细纤维状聚苯胺(superfine-fibrous PANI),经Pt微粒修饰后得到Pt微粒超细纤维聚苯胺复合电极[Pt／(superfine-fibrous PANI)／SS]。结果表明,直径50-100nm的Pt微粒均匀分布于直径约100nm的聚苯胺纤维上;Pt／(superfine-fibrous PANI)／SS电极对H2O2氧化具有很好的电催化活性。采用脉冲电流法(PGM)再将葡萄糖氧化酶(GOD)与间苯二胺(MPD)混合共聚嵌于Pt／(superilnefibrous PANI)／SS电极表面,获得了具有优异生物电化学传感特性的葡萄糖氧化酶电极。该酶电极最大响应电流密度im=917．4μA／cm^2,米氏常数K=9．339mmol／L;酶电极对葡萄糖响应快,对尿酸和抗坏血酸有很好的抗干扰性能。     

核壳结构聚苯胺-聚电解质-碳酸钙微球复合材料的制备、表征和应用

在包裹了聚电解质的碳酸钙微球上原位聚合苯胺,形成导电性良好的聚苯胺-聚电解质-碳酸钙（PAN/(PEs)6/CaCO3）微球。 采用扫描电子显微镜研究了聚电解质层对碳酸钙微球形貌的影响,以及苯胺单体加入量对碳酸钙-聚电解质-聚苯胺导电复合材料形貌的影响。 并用红外光谱和紫外-可见光谱等进行了结构表征。 该复合材料有良好的电催化活性,将其滴涂在玻碳电极上,修饰电极对多巴胺氧化显示了较强的催化能力,与碳酸钙修饰电极相比,其氧化峰电位负移了130 mV,平行制作5支修饰电极测定4.0 mmol/L多巴胺,相对标准偏差为4.2％。 该复合材料制备简单、重现性良好,可以构建测定多巴胺的传感器。 线性范围0.5~10.0 mmol/L,检测限0.2 mmol/L(3S/N)。     

载钯聚苯胺/聚砜复合膜修饰电极对甲酸的电催化氧化

采用电化学聚合法在铂电极表面制备了三维网状结构的聚苯胺(PAN)/聚砜(PSF)复合膜,并以此为载体制备了Pd/PAN/PSF复合膜电极,并用扫描电子显微镜对复合膜的微观形貌进行了表征。结果显示,此复合膜具有双层多孔结构,Pd纳米粒子在复合膜上平均粒径小、分散性好,有效地改善了Pd粒子的分散度和电极结构。电化学测试结果表明,Pd/PAN/PSF复合膜修饰电极对甲酸的电催化性能明显优于直接电沉积Pd的聚苯胺电极,并且表现出较高的稳定性。     

一种提高铂电催化氧化甲酸性能的简单方法

在离子液体1-乙基咪唑三氟乙酸盐(HElmTfa)中,采用循环伏安法在铂电极表面修饰聚吡咯(PPY),制得PPy-HEImTfa/Pt,并研究了其对甲酸的电催化氧化性能.与相同条件下的铂基底电极相比,PPy-HEImTfa/Pt对甲酸的电催化氧化性能有很大的提高.原位红外光谱表明,PPy-HElmTfa能降低中间体CO等对铂电极的毒化作用,促进甲酸直接氧化生成CO_2.     

Pt/PAn/Ti电极的制备及对甲醛的电催化氧化

通过循环伏安的电化学方法在金属钛基体上先后进行苯胺的聚合和金属铂的电化学沉积,得到以金属钛为基体的聚苯胺载铂电极(Pt/PAn/Ti),并通过扫描电镜和循环伏安法对该电极进行了表征。通过研究甲醛在该电极上的电催化氧化行为,考察了载铂量对甲醛氧化效果的影响及PAn在电催化氧化甲醛的过程中所起的作用。结果表明,载铂量与甲醛的氧化有一定的关系,PAn的存在使得铂微粒分散程度更好,有效面积更大,与相同铂沉积量的Pt/Ti电极相比,甲醛在其上的正向扫描氧化峰电流密度增加了2.3倍,电位负移了40mV;反向扫描氧化峰电流密度增加了5倍,电位负移了30mV。同时,PAn的存在也增强了电极的抗中毒能力。     

Nd-Fe-MoO42-氰桥混配聚合物修饰铂电极的丙三醇电催化氧化

利用软模板结合电沉积法制备了一种有序化氰桥混配聚合物修饰铂电极（Nd-Fe-MoO₄^2-/Pt）,用循环伏安法研究了在该化学修饰铂电极的丙三醇电催化氧化,并重点讨论了支持电解质的H⁺和SO₄^2-浓度、丙三醇浓度、扫速等因素对丙三醇电催化氧化活性的影响. 结果表明,在弱酸性硫酸钠支持电解质中,适当量SO₄^2-的存在有助于提高Nd-Fe-MoO₄^2-/Pt电极的丙三醇电催化氧化电流;-0.2 ~ 0.3 V电位区间内,其丙三醇氧化峰电流1与循环伏安曲线扫描速率的平方根之间呈现良好的线性关系,体现了扩散控制的反应特性;Nd-Fe-MoO₄^2-/Pt电极的丙三醇电催化氧化电流密度值约为裸铂电极的4倍,而丙三醇电催化氧化反应的表观活化能相对较小,修饰电极的电催化氧化呈现了明显的协同效应,其电催化氧化活性高、电流响应快、催化稳定性好.     

Pt(110)/Sb电极上甲酸的电催化氧化特征和动力学

研究了Sb在Pt(110)晶面上不可逆吸附电化学特性及甲酸在Sb_ad修饰Pt(110)电极[Pt(110)/Sb]上的电催化氧化特征及其反应动力学.发现当扫描电位的上限E_u≤0.45V时,Sb_ad可稳定地吸附在Pt(110)表面上,从而有效地抑制了甲酸的解离吸附.与未修饰的Pt(110)上的结果相比,在Pt(110)/Sb上甲酸氧化的峰电位负移了0.35V.当θ_Sb=0.126时,Pt(110)/Sb电极对甲酸的电催化活性最高.还研究了Pt(110)/Sb上甲酸氧化反应的动力学,定量解析了不同θ_Sb下甲酸氧化的速度常数kf和传递系数β.     

PmClAn基膜修饰电极的电化学及催化性质研究

聚苯胺作为电极修饰材料 ,已在传感器上显示出广泛的应用前景[1～ 4 ] .异丙醇 ( i- P)氧化[5,6 ] 是个较简单的反应 ,被广泛作为电催化研究的模型反应 .目前 ,i- P电化学氧化的研究集中于 Pt的多晶或单晶电极[7～ 9] ,Gonzales等 [10 ] 报道了 Pt- Sn共沉积的 PAn膜修饰电极上的异丙醇电氧化 ,但对复合材料的微观结构仍欠研究 .本文讨论 Pm Cl An基质性质对 Pt电沉积的影响 ,并探讨了 i- P在沉积 Pt微粒的 Pm Cl An功能膜电极上的氧化情况 .1　实验部分1 .1　电极的制备　聚间氯苯胺 ( Pm Cl An,本征态 ud,HCl掺杂态 d)采用乳液聚…     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.