A spectroscopic approach to assess transport properties of water vapor in PLA

The aim of this work is to describe in detail an experimental approach to quantitatively investigate water vapor transport properties in Poly (lactic acid), PLA. The approach is based on in situ time resolved Fourier Transform Infrared Spectroscopy, FTIR, in transmission mode, and provides a mean for monitoring accurately the penetrant sorption kinetics. FTIR spectra were analyzed by a deconvolution procedure, and the area of a specific peak (at 3651 cm^-1) was directly correlated to the amount of water inside the sample. The time evolution of this area was first normalized by using a peak uninfluenced by the amount of water and then interpolated to obtain the diffusivity parameter. The results were in good agreement with those obtained by more classical, and more complex microgravimetric methods.     

Selective detection of gas-phase TNT by integrated optical waveguide spectrometry using molecularly imprinted sol-gel sensing films

A chemical sensor was developed to detect the explosive 2,4,6-trinitrotoluene (TNT) utilizing planar integrated optical waveguide (IOW) attenuated total reflection spectrometry. Submicron thick films of organically modified sol-gel polymers were deposited on the waveguide surface as the sensing layer. Sol-gels were molecularly imprinted for TNT using covalently bound template molecules linked to the matrix through 1 or 2 carbamate linkages. Upon chemical cleavage of the template and displacement of the TNT-like pendant groups from the matrix, shape-selective binding sites were created that possess a primary amine group. The amine was used to deprotonate bound TNT yielding an anionic form that absorbs visible light. Binding of TNT and subsequent conversion to the anion results in the attenuation of light propagating through the waveguide, thus creating a spectrophotometric device. Sensitivity can be achieved by taking advantage of the substantial pathlength provided by the use of single mode IOWs. The limit-of-detection to gas-phase TNT was found to be five parts-per-billion (ppbV) in ambient air at a flow rate of 40 mL min⁻¹ given a 60 s sampling time. The sensor is highly selective for TNT due to the selectivity of binding site recognition of TNT and the subsequent generation of the TNT anion. Response to TNT is not reversible which results in an integrating sensor device which, in theory, can improve the ability to detect small amounts of the explosive if the exposure time is sufficient in length.     

Alloys prepared by plasma-enhanced chemical vapor deposition (PECVD)

Three different techniques for the deposition of thin metal alloy films by plasma-enhanced chemical vapor deposition are described. These are the joint vaporization of a mixture of precursors, the use of separate sources connected directly to the reactor, and finally, the use of several reservoirs arranged in series. Various organometallics have been used as precursors to prepare combinations of Fe/Co and Au/Pt/Pd.     

PLA-ZnO nanocomposite films: Water vapor barrier properties and specific end-use characteristics

PLA nanocomposite films with multifunctional characteristics such as mechanical, anti-UV, antibacterial, electrical, gas barrier properties are potentially of high interest as packaging biomaterials. Occasionally, desired and beneficial effects obtained by addition nanofillers come along with some drawbacks, leading to the sharp drop in the molecular weights of the polyester chains, and consequently an important loss of mechanical and thermal properties. Novel PLA-ZnO nanocomposite films were produced by melt-compounding PLA with 0.5–3% ZnO rod-like nanoparticles. The surface treatment of nanofiller by silanization (with triethoxy caprylylsilane) was necessary to obtain a better dispersion and to limit the decrease of molecular mass of PLA. The morphology, molecular, thermo-mechanical and transport properties to water vapor of PLA-ZnO films were analyzed with respect to the neat PLA. According to DSC and to XRD, the produced films were essentially amorphous. The changes in PLA permeation properties were strongly dependent on temperature and nanofiller loading. The well dispersed ZnO nanoparticles within the polyester matrix were effective in increasing the tortuosity of the diffusive path of the penetrant molecules. The activation energy remained similar for PLA and PLA-1% ZnO, but was found greater at higher loading of ZnO (3%), confirming the increased difficulty of travelling molecules to diffuse through PLA. In comparison to the neat PLA (presenting no antimicrobial efficacy), the nanocomposites were active against both Gram-positive and Gram-negative bacteria, stronger antibacterial activity being evidenced after 7 days elapsed time. By considering the multifunctional properties of PLA-ZnO nanocomposites, the films produced by extrusion can be considered a promising alternative as environmental-friendly packaging materials.     

Application of laser photoacoustic spectroscopy for the detection of water vapor near 1.38 μm

Laser photoacoustic (PA) spectroscopy is applied for the determination of the trace content of water vapor using a differential Helmholtz resonant (DHR) cell and a narrow bandwidth diode laser operating near 1380 nm. The PA spectroscopy revealed a rich absorption spectra in this wavelength region and the observed result was compared with the HITRAN database. A multipass optical system was also developed by adopting one aluminum-coated flat mirror with a small uncoated spot for the laser introduction to the detection chamber and one aluminum-coated concave mirror. The multipass optical system enabled the enhancement of the PA signal up to eight times when compared to the single pass case. The calibration curve was plotted by measuring PA signals for various pressures of the water vapor. The sensitivity of the PA detection system is estimated as 7.3×10¹² molecules cm⁻³ with a signal-to-noise ratio (SNR) of 1.     

Application of laser photoacoustic spectroscopy for the detection of water vapor near 1.38 μm

Laser photoacoustic (PA) spectroscopy is applied for the determination of the trace content of water vapor using a differential Helmholtz resonant (DHR) cell and a narrow bandwidth diode laser operating near 1380 nm. The PA spectroscopy revealed a rich absorption spectra in this wavelength region and the observed result was compared with the HITRAN database. A multipass optical system was also developed by adopting one aluminum-coated flat mirror with a small uncoated spot for the laser introduction to the detection chamber and one aluminum-coated concave mirror. The multipass optical system enabled the enhancement of the PA signal up to eight times when compared to the single pass case. The calibration curve was plotted by measuring PA signals for various pressures of the water vapor. The sensitivity of the PA detection system is estimated as 7.3×10¹² molecules cm⁻³ with a signal-to-noise ratio (SNR) of 1.     

光波导乙醇气体传感器的研究

以聚偏氟乙烯(PVDF)作为敏感试剂固定在钾(K⁺)离子交换玻璃光波导表面,研制了光波导乙醇气体传感器.该传感器具有可逆性好、灵敏度高、响应速度快、选择性和重现性好、能在室温操作等特点.     

VCSEL based detection of water vapor near 940nm

A vertical-cavity surface-emitting laser (VCSEL) was used to study the absorption spectrum of water vapor in the 940nm region. Measurements were performed in ambient air at room temperature and in a hydrogen-oxygen flame over the temperature range of 1500-1800K. Several rotational absorption lines within the 2v1 + v3 vibrational band were measured. The absorption spectra were well resolved, which demonstrates the feasibility of VCSEL-based spectroscopic measurements of water vapor at room and high-temperature in this spectral region. The results were in good agreement with the values obtained from the HITRAN-96 database.     

Sorption and diffusion of water vapor in polyimide films

Sorption and diffusion of water vapor are investigated gravimetrically for polyimide films. The activity dependence of the solubility and diffusion coefficients, S and D, respectively, is classified under four types: (1) constant S and D type, (2) dual-mode sorption and transport type, (3) dual-mode type followed by a deviation due to a plasticization effect at high vapor activity, and (4) constant S and D type followed by a deviation due to water cluster formation at high activity. For the dual-mode type, the Henry's law component is much larger than the Langmuir component except at low activity, and therefore deviation in behavior from the first type is small. S is larger for polyimides with higher content of polar groups such as carbonyl, carboxyl, and sulfonyl. D is larger for polyimides with a higher fraction of free space, with some exceptions. The polyimide from 3,3′,4,4′-biphenyltetracarboxylic dianhydride and dimethyl-3,7-diaminodibenzothiophene-5, 5-dioxide belongs to the third type and displays both large S and large D. The polyimide from 2,2-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride and 4,4′-oxydianiline belongs to the fourth type, and has the largest D but rather small S because of the hydrophobic C(CF₃)₂ groups. © 1992 John Wiley & Sons, Inc.     

基于硫堇掺杂的聚乙烯醇薄膜的光波导传感器检测硫化氢气体

采用旋转甩涂法将硫堇掺杂的聚乙烯醇薄膜固定在K⁺交换玻璃光波导表面,研制出一种高灵敏硫化氢气体传感器。 传感膜与硫化氢(H₂S)气体作用时,薄膜颜色从紫色变为无色,从而降低薄膜对倏逝波的吸收,使传感器的输出光强度（信号）增强。 采用流动注射法对H₂S气体进行检测。 实验结果表明,H₂S传感器对浓度在0.14~56 mg/m3范围的H₂S气体具有良好的线性响应（r=0.99667）,检出限为0.11 mg/m³(S/N=3),相对标准偏差为4.0%,响应时间（t90）＜2 s。 该传感器具有灵敏度高、响应快、可逆性和重复性好等特点。     

Free volume and water vapor permeability of dense segmented polyurethane membrane

This paper presented micro-structure, free volume and water vapor permeability of dense segmented polyurethane (SPU) membrane. Wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM) techniques were employed to investigate the micro-structure. Free volume was measured by positron annihilation life spectroscopy (PALS). WAXD and DSC results indicated microcrystalline structure presents in the polymer membrane. Percent crystallinity of SPU would depend on the types of polyol used. The microphase-separated structure of copolymers was observed by transmission electron microscopy. Extent of phase separation was depended on the type and composition of polyol used. Free volume hole sizes are different for SPU samples due to the interaction between the polymer chains and packing of polymer chains due to the different compositions. The influences of temperature and chemical compositions on the free volume and water vapor permeability have been discussed. Experimental results revealed that the water vapor permeability can be controlled by free volume, which would depend on the chemical composition of SPU, and hydrophilicity of membranes.     

Optical anisotropy of polymeric films measured by waveguide propagation mode determination

Extruded thin films of a liquid-crystalline charge-conjugated rigid-rod polymer poly(p-phenylenebenzobisthiazole), PBT, and a semicrystalline thermoplastic polyethylene-terephthalate (Mylar) were fabricated and examined for film thickness, refractive index, and linear attenuation coefficient. Optical waveguide modes were successfully induced on the polymeric films using a prism coupler at λ = 633 and 1300 nm. Highly consistent thickness values were obtained for the polymeric films. In addition, the anisotropic nature of the optical properties was determined using TE and TM propagation modes. A refractive index as high as 2.3 was observed on PBT film. The refractive index data suggested that the PBT and Mylar films were optically anisotropic with refractive indices n? (out-of-plane) invariably smaller than n∥ (in-plane). Large anisotropy was also discovered in the linear attenuation coefficient α, with α_∥/α_? ≈ 50 for the Mylar films. Complementary polarimetric and spectroscopic interference measurements were also applied to investigate the optical anisotropy of the extruded polymeric films. © 1992 John Wiley & Sons, Inc.     

Comparison of the properties of waterborne polyurethane-ureas containing different triblock glycols for water vapor permeable coatings

Four types of triblock glycols [(CL)_4.5-PEG-(CL)_4.5, (CL)_4.5-PTAd-(CL)_4.5, (CL)_4.5-PTMG-(CL)_4.5, and (CL)_4.5-PPG-(CL)_4.5, Mn=3,000] were synthesized by end-capping reactions of -caprolactone (CL) and poly(ethylene) glycol (PEG, Mn=2,000), poly(tetramethylene adipate) glycol (PTAd, Mn=2,000), poly(tetramethylene) glycol (PTMG, Mn=2,000), or polypropylene glycol (PPG, Mn=2,000)]. Waterborne polyurethanes (WBPUs) were prepared by polyaddition reaction using 4,4-dicyclohexylmethane diisocyanate (H₁₂MDI), 2,2-bis (hydromethyl) propionic acid (DMPA), ethylene diamine (EDA), triethyl amine (TEA), and the triblock glycol. Studies have been conducted on the effects of triblock glycol type on the colloidal properties of dispersion, the hardness and mechanical properties of WBPU films, the water vapor permeability (WVP), and water resistance (WR) of WBPU-coated nylon fabrics. The WVP (%WVP based on control nylon fabric) of WBPU-coated nylon fabrics based on (CL)_4.5-PEG-(CL)_4.5, (CL)_4.5-PTAd-(CL)_4.5, (CL)_4.5-PTMG-(CL)_4.5 and (CL)_4.5-PPG-(CL)_4.5 were 3,975(81), 3,115(62), 3,124(64), and 2,569(52) g/m² day (%), respectively. However, the WBPU based on (CL)_4.5-PEG-(CL)_4.5 was not applicable for coating material, because its dispersion and film had relatively high viscosity (3,000 cps at 50°C) and low mechanical properties, respectively. In this work, the triblock glycols (CL)_4.5-PTMG-(CL)_4.5 and (CL)_4.5-PTAd-(CL)_4.5 were found to be desirable glycols for water vapor permeable coating materials.     

Chemical vapor deposition growth of phase-selective inorganic lead halide perovskite films for sensitive photodetectors

Inorganic lead halide perovskites are attractive optoelectronic materials owing to their relative stability compared to organic cation alternatives.The chemical vapor deposition(CVD) method offers potential for high quality perovskite film growth.The deposition temperature is a critical parameter determining the film quality owing to the melting difference between the precursors.Here,perovskite films were deposited by the CVD method at various temperatures between 500-800℃.The perovskite phase converts from CsPb₂Br₅ to CsPbBr₃ gradually as the deposition temperature is increased.The grain size of the perovskite films also increases with temperature.The phase transition mechanism was clarified.The photoexcited state dynamics were investigated by spatially and temporally resolved fluorescence measurements.The perovskite film deposited under 750℃ condition is of the CsPbBr₃ phase,showing low trap-state density and large crystalline grain size.A photodetector based on perovskite films shows high photocurrent and an on/off ratio of ~2.5×10⁴.     

The polyurethane membranes with temperature sensitivity for water vapor permeation

The size and shape of free-volume holes available in membrane materials control the rate of gas diffusion and its permeability. Based on this principle, two segmented thermo-sensitive polyurethane (TSPU) membranes with functional gates, i.e. the ability to sense and respond to external thermo-stimuli, were synthesized and used for water vapor controllable permeation. Differential scanning calorimetry (DSC), positron annihilation lifetimes (PAL), water swelling and water vapor permeability (WVP) were used to evaluate how the structure of the polyurethane (PU) and the temperature influence the free-volume holes size and the water vapor permeability (WVP) of the PU membranes. DSC study reveals that TSPU with a glass transition or a crystalline transition reversible phase shows an obvious phase-separated structure and a phase transition temperature (defined as switch temperature, T_s). PAL study indicates that the free-volume holes size of TSPU is closely related to the T_s. When the temperature is higher than the T_s, the ortho-positronium (o-Ps) lifetime (τ₃) and the average radius (R) of free-volume holes of TSPU membrane increase dramatically. As a result, the WVP of TSPU membrane shows a dramatic increase. Additionally, the water swelling and the WVP of TSPU membrane are found to depend on the inner structure of the polymer, and they also give different responses to temperature variation. When the temperature is higher than the T_s, there is a significant increase of WVP from 3.80 kg/m² day to 7.63 kg/m² day for TSPU(a) and from 4.30 kg/m² day to 8.58 kg/m² day for TSPU(b), respectively. Phase transition accompanying significant changes in free-volume holes size and WVP can be used to develop “smart membranes” with functional gates and controllable gas permeation.     

Organic vapor sensing properties of copolymer Langmuir-Blodgett thin film sensors

In this study, a novel poly[Styrene (ST)-co-Glycidyl Methacrylate (GMA)] copolymer material is used to fabricate Langmuir-Blodgett (LB) thin films and investigate organic vapor sensing properties. Quartz Crystal Microbalance (QCM) system is used to investigate gas sensing performance of copolymer LB films during exposure to Volatile Organic Compounds (VOCs). The poly[Styrene (ST)-co-Glycidyl Methacrylate (GMA)] LB thin film sensor sensitivities are determined to be between 0.12 and 0.25 Hz ppm^?1. Detection limits of the copolymer LB thin film are found to be between 23 and 49 ppm against organic vapors. The copolymer LB thin films are more sensitive to chloroform than other vapors used in this study. The results demonstrated that the poly[Styrene (ST)-co-Glycidyl Methacrylate (GMA)] copolymer material is promising as a organic vapor sensing device at room temperature.     

A simple test method for measuring water vapor resistance of porous polymeric materials

A simple test method is proposed for measuring water vapor resistance of fabrics. A piece of cotton fabric connected to a container filled with distilled water through a plastic tube was used on a hot plate to generate a saturated water vapor condition on one side of the sample. The temperature of the cotton fabric (approximation of human skin covered with sweat) was measured by a thermocouple. The water vapor resistance of the sample was determined based on the water vapor pressure gradient across the sample and the heat flux. Five types of textile fabric laminated to PU/TPU membranes, plus one type of conventional fabric, were tested by using this simple apparatus as well as the sweating guarded hot plate instrument. The results showed that good agreement was observed between these two test methods. In addition, the surface temperature of the cotton ‘skin’ varied with different fabrics. This is in accordance with the actual intended situation, i.e., the skin temperature of the body is related to the ability of clothing materials to transfer water vapor. Therefore, this simple test apparatus better simulates real-life conditions than the sweating guarded hot plate instrument.     

Evolution of water vapor from indium-tin-oxide thin films fabricated by various deposition processes

Tin-doped In₂O₃ (indium-tin-oxide) transparent conducting films are widely used as electrodes of liquid crystal displays and low-E windows. In the present study, a systematic TDS study was undertaken for ITO films fabricated by various deposition processes; such as PVD, dip coating and spray deposition. Water vapor was the main gas evolved from the films; gas evolution from the silicon substrate was negligible. The evolution proceeded via two steps at approximately 373 and 473-623 K. The amount of the evolved water was in the order: (dip-coated film)>(PVD films)> (spray-deposited film). This order was identical to that of the film's resistivities. This revised version was published online in August 2006 with corrections to the Cover Date.     

高灵敏复合光波导在检测臭氧的应用研究

介绍利用高灵敏复合光波导元件检测臭氧的一种新方法以及实验装置和臭氧的响应特征。通过在K^＋交换玻璃光波导表面形成高折射率TiO2（两端带斜坡带状）膜并在其表面上固定色素铜化酞箐（Coppertetra-（t-buthyl）phthalocyanine,TBPcCu）而制成高灵敏度的复合光波导元件。臭氧存在时TBPcCu薄膜被氧化而退色,由此减弱TBPcCu膜对633nm的导波光的吸收。本元件具有响应速度快,灵敏度高和检测极限在0．02mg/m^3等特点。     

Efficient enhancement of the thermoelectric performance of vapor phase polymerized poly(3,4‐ethylenedioxythiophene) films with poly(ethyleneimine)

Tuning the molecular rearrangement and oxidation level has been proven to be effective strategies for optimizing the thermoelectric (TE) performance of PEDOT. It is difficult to achieve these effects simultaneously via a one‐step process, however. In this work, we combined vapor phase polymerization (VPP) and H₂SO₄ post‐treatment to obtain a highly conductive PEDOT film. A novel strategy using polyethylenemine (PEI) as an effective reducing agent was employed to enhance the thermopower of the PEDOT film. Grazing‐Incidence Wide‐Angle X‐ray Scattering analysis and the changes in the oxidation level allow us to elucidate the role of PEI and its transport mechanism. It is demonstrated that the thermopower of well‐ordered crystallites in the PEDOT film significantly increases more than five times (from 11 to 59 μV K^?1) by the PEI‐DMF solution immersion process, while the electrical conductivity is maintained at 100 S cm^?1. The promising method connecting VPP, H₂SO₄, and PEI shows great potential for effectively tuning the thermopower of organic TE materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 257–265