Carbon ceramic electrode incorporated with zeolite ZSM-5 for determination of Piroxicam

A new chemically modified electrode is constructed based on carbon ceramic electrode incorporated with zeolite ZSM-5. Voltammetric behavior of piroxicam at the carbon ceramic zeolite modified electrode (CCZME) was investigated. The modified electrode exhibited catalytic activity toward the electrooxidation of piroxicam. Experimental parameters such as solution pH, scan rate, concentration of piroxicam and zeolite amount were studied. It has been shown that using the CCZME, piroxicam can be determined by differential pulse voltammetry (DPV) and hydrodynamic amperometry (HA). Under the optimized conditions the calibration plots are linear in the concentration ranges of 0.20–25.00 and 0.20–50.10 μM with limit of detections of 0.65 and 0.29 μM for DPV and HA, respectively. The modified electrode with DPV and HA methods was successfully applied for analysis of piroxicam in pharmaceutical formulations. The results were favorably compared to those obtained by the spiked method. The results of the analysis suggest that the proposed method has promise for the routine determination of piroxicam in the products examined.     

Renewable-surface sol-gel derived carbon ceramic electrode fabricated by [Ru(bpy)(tpy)Cl]PF6 and its application as an amperometric sensor for sulfide and sulfur oxoanions

A highly sensitive and fast responding sensor for the determination of thiosulfate, sulfite, sulfide and dithionite is described. It consists of a chemically modified carbon ceramic composite electrode (CCE) containing [Ru(bpy)(tpy)Cl]PF6 complex that was constructed by the sol-gel technique. A reversible redox couple of Ru(II)/Ru(III) was observed as a solute in acetonitrile solution and as a component of carbon based conducting composite electrode. Electrochemical behavior and stability of modified CCE were investigated by cyclic voltametry, the apparent electron transfer rate constant (kappa(S)) and transfer coefficient (a) were determined by cyclic voltametry which were about 28 s(-1) and 0.43 respectively. Electrocatalytic oxidation of S(2-), SO3(2-), S2O4(2-) and S2O3(2-) were effective at the modified electrode at significantly reduced overpotentials and in the pH range 1-11. Optimum pH values for amperometric detection of thiosulfate, dithionite, sulfide and sulfite are 7, 9, 2 and 2. Under the optimized conditions the calibration curves are linear in the concentration ranges 1-500, 3-80, 2-90 and 1-100 microM for S2O3(2-), SO3(2-), S2- and S2O4(2-) determination. The detection limit (signal to noise is 3) and sensitivity are 0.5 and 12, 2.8 and 6, 1.6 and 8, and 0.65 microM and 80 nA microM(-1) for thiosulfate, sulfite, sulfide and dithionite detection. The modified carbon ceramic electrode doped with Ru-complex shows good reproducibility, a short response time (t < 2 s), remarkable long term stability (> 6 month) and especially good surface renewability by simple mechanical polishing (RSD for eight successive polishing is 2%). The advantages of this sulfur compound amperometric detector based on ruthenium doped CCE are high sensitivity, inherent stability at a broader pH range, excellent catalytic activity, less expense and simplicity of preparation in comparison with recently published papers. This sensor can be used as a chromatographic detector for analysis of sulfur derivatives.     

Adsorption and Reactivity of Chlorogenic Acid at a Hydrophobic Carbon Ceramic Composite Electrode: Application for the Amperometric Detection of Hydrazine

Sol-gel technique was used for construction of a carbon composite electrode. The prepared carbon ceramic electrode was modified with electroless deposition of chlorogenic acid for less than 1 min. The adsorbed thin films of chlorogenic acid on carbon composite electrode show one pair of peaks with a surface confined characteristic, which strongly depends on the solution pH, as anticipated for quinone /hydroquinone functionalities. The modified electrode shows highly catalytic activity toward hydrazine electrooxidation at wide pH range (5–11). Also the rotating modified electrode shows excellent analytical performance for amperometric determination of hydrazine. The detection limit, sensitivity, response time and linear dynamic range are 20 nM, 220 nA / μM, 1 second and 0.1 μM-1 mM, respectively. The catalytic rate constant for hydrazine oxidation at the surface of modified electrode was evaluated by cyclic voltammetry and was found to be around 1.5×10³ M⁻¹s⁻¹in phosphate buffer solution (pH 8). The precision of chronoamperometric measurements was 1–3% for 5 replicate determinations in the concentration range of the linear calibration. The reproducibility of modified CCE was evaluated with 8 successive polishing and modifications and then the anodic peak current was measured (RSD 2%). The advantages of this sensor are excellent catalytic activity, high sensitivity, good reproducibility and simplicity of preparation at short time periods.     

Sol-gel-derived carbon ceramic electrode containing 9,10-phenanthrenequinone, and its electrocatalytic activity toward iodate

9,10-Phenanthrenequinone (PQ) supported on graphite powder by adsorption was dispersed in propyltrimethoxysilane-derived gels to yield a conductive composite which was used as electrode material to fabricate a PQ-modified carbon ceramic electrode. In this configuration, PQ acts as a catalyst, graphite powder guarantees conductivity by percolation, the silicate provides a rigid porous backbone, and the propyl groups endow hydrophobicity and thus limit the wetting region of the modified electrode. Square-wave voltammetry was exploited to investigate the pH-dependent electrochemical behavior of the composite electrode and an almost Nernstian response was obtained from pH 0.42 to 6.84. Because the chemically modified electrode can electrocatalyze the reduction of iodate in acidic aqueous solution (pH 2.45), it was used as an amperometric sensor for the determination of iodate in table salt. The advantages of the electrode are that it can be polished in the event of surface fouling, it is simple to prepare, has excellent chemical and mechanical stability, and the reproducibility of surface-renewal is good.     

Solid-contact Cu(II) ion-selective electrode based on 1,2-di-(<Emphasis Type="Italic">o</Emphasis>-salicylaldiminophenylthio)ethane

The development of Cu(II) solid-contact ion-selective electrodes, based on 1,2-di-(o-salicylaldiminophenylthio)ethane as a neutral carrier, is presented. For the electrodes construction, unmodified carbon ink (type 1 electrode) and polymer membrane-modified carbon ink (type 2 electrode) were used as solid support and transducer layer. Also, carbon ink composite polymer membrane electrode (type 3 electrode) was prepared. The analytical performance of the electrodes was evaluated with potentiometry, while bulk and interfacial electrode features were provided with electrochemical impedance spectroscopy. It is shown that modification of carbon ink with polymer membrane cocktail decreases the bulk contact resistance of the transducer layer and polymer membrane, thus enhancing the analytical performance of the electrode in terms of sensitivity, linear range, and stability of potential. The optimized electrodes of types 2 and 3 exhibit a wide linear range with detection limits of 1.8 × 10⁻⁶ and 1.6 × 10⁻⁶ M, respectively. They are suitable for determination of Cu²⁺ in analytical measurements by direct potentiometry and in potentiometric titrations, within pH between 2.3 and 6.5. The electrodes are selective for Cu²⁺ over a large number of tested transition and heavy metal ions.     

Sol-gel derived carbon ceramic electrode containing methylene blue-intercalated α-zirconium phosphate micro particles

Methylene blue-intercalated alpha-zirconium phosphate (MBZrP) micro particles in deionized water were deposited onto the surface of graphite powder to prepare graphite powder-supported MBZrP, which was subsequently dispersed into methyltrimethoxysilane-derived gels to yield a conductive composite. The composite was used as electrode material to fabricate a surface-renewable, rigid, leak-free carbon ceramic composite electrode, bulk-modified with methylene blue (MB). In the configuration, alpha-zirconium phosphate was employed as a solid host for MB, which acted as a catalyst. Graphite powder ensured conductivity by percolation, the silicate provided a rigid porous backbone and the methyl groups endowed hydrophobicity and thus limited the wetting section of the modified electrode. Peak currents of the MBZrP-modified electrode were surface-confined at low scan rates but diffusion-controlled at high scan rates. Square-wave voltammetric study revealed that MBZrP immobilized in carbon ceramic matrix presented a two-electron, three-proton redox process in acidic aqueous solution with pH ranged from 0.44 to 2.94. In addition, the chemically modified electrode showed an electrocatalytic activity toward nitrite reduction at +0.15 V ( vs. Ag/AgCl) in acidic aqueous solution (pH=0.44). The linear range and detection limit are 1x10(-6)-4x10(-3) mol x L(-1) and 1.5x10(-7) mol x L(-1), respectively.     

The Mn‐zeolite/Graphite Modified Glassy Carbon Electrode: Fabrication,Characterization and Analytical Applications

In this work, low‐cost and environmentally friendly natural zeolite exchanged with Mn²⁺ cations was used for the first time to modify the glassy carbon electrode with the aim to obtain a fast and simple sensor for voltammetric determination of paracetamol (PAR). The Mn‐zeolite/graphite modified glassy carbon electrode (MnZG?GCE) was prepared by evaporation of solvent from dispersion of the zeolite/graphite mixture with the polymer in acetone. The electrochemical characteristics of MnZG?GCE were conducted by electrochemical impedance spectroscopy and cyclic voltammetry. Compared with graphite modified GCE (G?GCE), MnZG?GCE exhibited better electrochemical parameters, which confirms the superiority of applying zeolite in the proposed sensor. The optimization of the pH‐value of supporting electrolyte and instrumental parameters were carried out. The peak current was proportional to the concentration of PAR in a phosphate buffer saline of pH 6.0 in the range from 0.029 to 0.69 mg L^?1 (R=0.9997) with limit of detection of 8.8 μg L^?1. Finally, the proposed electrode was successfully applied to determine the paracetamol in pharmaceutical formulation and certified reference materials. The satisfactory recoveries, which ranged from 89.2 to 102.7 %, were obtained for all studied samples. It confirmed the attractiveness of relatively inexpensive, easy to fabricate and non‐toxic MnZG?GCE in determination of PAR in complicated matrixes.     

Zeolite Nanoparticle Modified Carbon Paste Electrode as a Biosensor for Simultaneous Determination of Dopamine and Tryptophan

A new chemically modified electrode is constructed based on an iron(III) doped zeolite modified carbon paste electrode (Fe³⁺Y/ZCME). The electrode was evaluated as a sensor for sub‐micromolar determination of tryptophan (Trp) and dopamine (DA). The measurements were carried out using the differential pulse voltammetry (DPV) method in a phosphate buffer solution with pH = 5. The prepared modified electrode shows voltametric responses with high sensitivity and stability for DA and Trp in optimal conditions. The analytical performance of this sensor has been evaluated for detection of DA and Trp in human serum.     

Electrocatalytic properties of [Ru(bpy)(tpy)Cl]PF6 at carbon ceramic electrode modified with nafion sol-gel composite: application to amperometric detection of l-cysteine

A two-step sol-gel technique was used here to prepare a carbon ceramic electrode modified with nafion and [Ru(bpy)(tpy)Cl]PF₆. This involves two steps: first, forming a bulk-modified carbon ceramic electrode with nafion, and then immersing the electrode into a Ru-complex solution (electroless deposition) for a short period of time (5-25 s). Cyclic voltammograms of the resulting surface-modified carbon ceramic electrode show stable and a well-defined redox couple due to Ru(II)/Ru(III) system with surface-confined characteristic. l-Cysteine (CySH) has been chosen as a model to elucidate the electrocatalytic ability of Ru-complex nafion sol-gel composite electrode. Not only the modified electrode shows excellent catalytic activity toward l-cysteine electrooxidation in pH range 3-9, but the antifouling effect of nafion film also increases the reproducibility of results in comparison with CCE modified with homogeneous mixing of graphite powder and Ru-complex (one step sol-gel method). Under the optimized conditions in amperometry method, the concentration calibration range, detection limit and sensitivity were 0.1-100 μM, 20 nM and 50 nA/μM, respectively. The advantages of this modified electrode are good reproducibility, excellent catalytic activity, simplicity of preparation and especially its antifouling properties towards l-cysteine and its oxidation products. Additionally, it is promising as a detector in flow system or chromatography systems.     

Amperometric sensor for L-ascorbic acid determination based on MnO2 bulk modified screen printed electrode

A simple biosensor constructed by bulk-modification of carbon ink with manganese dioxide as a mediator was investigated for its ability to serve as amperometric detector for L-ascorbic acid in hydrodynamic mode. The sensor could be operated at pH 5.0 (0.05 M phosphate buffer) and exhibited excellent reproducibility and stability. Optimization of measurement parameters such as applied working potential and pH value were studied in detail. The screen printed electrode exhibited a linear amperometric increase with the concentration of L-ascorbic acid from 50 mg L(-1) to 250 mg L(-1) and gave a (LOD = 3sigma) detection limit of 0.2 mg L(-1) (1.172 micromol L(-1)). The manganese dioxide modified screen printed electrode shows long term stability.     

Electrochemical Behavior and Voltammetric Determination of Diclofenac at a Multi-Walled Carbon Nanotube-Ionic Liquid Composite Modified Carbon Ceramic Electrode

This work describes the electrochemical behavior of diclofenac on the surface of a carbonceramic electrode (CCE) modified with multi-walled carbon nanotubes (MWCNT) and an ionic liquid (IL) composite. The MWCNT-IL composite showed an enhancement effect in the electro-oxidation of diclofenac with respect to a bare carbon ceramic electrode. Based on the experimental outcomes, a possible mechanism for the electro-oxidation of diclofenac is proposed and discussed. Under the optimized experimental conditions, the MWCNT-IL CCE showed a linear response to diclofenac over the concentration range 50 nM–20 µM with a detection limit of 27 nM. The developed diclofenac sensor showed good stability, sensitivity, and reproducibility in the measurement of diclofenac in human blood plasma samples.     

Nonenzymatic amperometric glucose sensor based on a composite prepared from CuO,reduced graphene oxide,and carbon nanotube

Microchimica Acta - The authors demonstrate a non-enzymatic sensor for glucose that is making used of an electrode prepared from an ink composed of CuO, reduced graphene oxide and carbon nanotube...     

Determination of an Ethylene Bisdithiocarbamate Based Pesticide (Nabam) by Cobalt Phthalocyanine Modified Carbon Ink Electrode

A phthalocyanine based sensor, for anodic detection of sodium ethylene bisdithiocarbamate (Nabam) by coating a mixture of cobalt phthalocyanine (CoPC) modified carbon ink on the surface of a glassy carbon electrode, has been described. The modified ink was prepared by mixing three percent of cobalt phthalocyanine into carbon ink and then diluting the mixture with cyclohexanone in w/w ratio of 1/9. A suitable portion (or 1 μL) of ink mixture was then dip‐coated on a rotating disk glassy carbon electrode. The modified ink electrode was air‐dried for 15 mins before use. In comparison to the bare ink electrode on which the oxidation of Nabam takes place at 300 mV (vs. 3 M Ag/AgCl), the oxidation potential (?125 mV) of Nabam at the CoPC modified ink decreases significantly. A typical calibration plot of Nabam proportionally increases over the concentration range of 2.5 to 36 μM (R=0.9990). The detection limit is estimated about 28.8 nM (S/N=3) and its response time (between 10% to 90% of steady‐state response) is about 5.3 s at the injection of 5 μM Nabam. The sensitivity requirement of JMPR meeting (Joint FAO/WHO Meeting on Pesticide Residues) for ethylene bisdithiocarbamates (EBDCs) is achieved by this proposed scheme.     

Simultaneous determination of tryptophan, uric acid and ascorbic acid at iron(III) doped zeolite modified carbon paste electrode

A new chemically modified electrode is constructed based on iron(III) doped zeolite modified carbon paste electrode (Fe(3+)Y/ZCME). The electrode was evaluated as a sensor for sub-micromolar determination of tryptophan (Trp), uric acid (UA) and ascorbic acid (AA) in aqueous solutions. The measurements were carried out by application of the differential pulse voltammetry (DPV) method in phosphate buffer solution with pH 3.5. Iron(III) loaded in zeolite can increase anodic peak currents by adsorption of Trp, UA and AA on electrode surface The analytical performance was evaluated with respect to the carbon paste composition, pH of solution, accumulation time and accumulation potential. The prepared electrode shows voltammetric responses with high sensitivity and selectivity for Trp, UA and AA in optimal conditions, which makes it very suitable for simultaneous determination of these compounds. The linear calibration range for AA in the presence of 50muM UA and 50muM Trp was 0.6muM to 100muM, with a correlation coefficient of 0.9992, and a detection limit of 0.21muM (S/N=3). A linear relationship was found for UA in the range of 0.3-700muM containing 10muM AA and 50muM Trp, with a correlation coefficient of 0.9990 and a detection limit of 0.08muM. The linear calibration range for Trp in the presence of 10muM AA and 50muM UA was 0.2-150muM, with a correlation coefficient of 0.9996, and a detection limit of 0.06muM. The proposed method was successfully applied for determination Trp, UA and AA in biological systems and pharmaceutical samples.     

A simplified methodology: pH sensing using an in situ fabricated Ir electrode under neutral conditions

Herein, a simplified fabrication method for the producing of a pH-sensitive iridium electrode is developed. The in situ electrochemical fabrication of an iridium oxide film is optimized and shown to be achievable under neutral conditions rather than the acidic conditions hitherto employed. The formation of a pH sensitive Ir(III/IV) hydrous film is confirmed via XPS. The amperometric pH-sensing properties of this electrochemically generated material were investigated using square wave voltammetry. In the pH range 2–13, the iridium oxide redox signal has a pH dependency of 86.1 ± 1.1 mV per pH unit for midpoint potentials with uncertainties being ± 0.01–0.05 pH. Finally, the newly developed pH sensor was used to measure the pH of a natural water sample with excellent results as compared to a conventional glass pH probe.

     

Adsorption and redox processes at carbon nanofiber electrodes grown onto a ceramic fiber backbone

The adsorption of aromatic compounds onto activated carbons and carbon nanofibers is of considerable technical importance and beneficial in electroanalytical procedures. Here, effects due to the strong adsorption of hydroquinone, benzoquinone, and phenol onto carbon nanofiber electrodes immersed in aqueous media are reported. Carbon nanofiber materials (fiber diameter approximately 100 nm) are grown onto ceramic fiber substrates by employing an ambient pressure chemical vapour deposition process. The resulting composite electrode material is sufficiently electrically conducting due to the high carbon content and mechanically robust due to the ceramic backbone. It is shown that the voltammetric signal obtained for the one electron reduction of Ru(NH₃)₆³⁺ is dominated by solution trapped in the three-dimensional electrode structure. In contrast, for the hydroquinone/benzoquinone redox system in aqueous phosphate buffer (pH 7) strong adsorption onto the carbon nanofiber material is observed. In the presence of phenol also strong adsorption is detected. In the course of the chemically irreversible oxidation of phenol in aqueous phosphate buffer (pH 7), the formation of multi-electron oxidation products related to benzoquinone is observed. The pathway for the oxidation process is attributed to (i) the high surface area of the carbon nanofiber electrode and (ii) the adsorption of intermediates.     

Determination of Imidacloprid in Tomato Grown in Greenhouse Based on Copper(II) Phthalocyanine Modified Carbon Ceramic Electrode by Differential Pulse Voltammetry

A new sol‐gel derived electrocatalytic carbon ceramic electrode was prepared by incorporating copper(II) phthalocyanine (CuPc) in a carbon ceramic network. This electrode was used as a sensitive electrochemical sensor for determination of the insecticide Imidacloprid (1‐(6‐chloro‐3‐pyridylmethyl)‐N‐nitro‐imidazolidin‐2‐ylideneamine) by differential pulse voltammetry (DPV). The resulting modified electrode exhibits a cathodic peak potential shifted positively and an increasing in cathodic peak current in comparison with unmodified electrode. The redox properties of this modified electrode at various pH values and CuPc percentage were investigated. The catalytic current obtained from differential pulse voltammetry is linearly dependent on Imidacloprid concentration over the two linear ranges of 0.67‐17 μM and 17‐93 μM with correlation coefficient of R² = 0.9999 and R² = 0.990, respectively. The detection limit for Imidacloprid was found to be 0.28 μM according to lower linear range. Possible interferences from several common pesticides were also evaluated. The inherent stability, high sensitivity, low detection limit and low cost for each preparation are advantages of this sensor. Determination of Imidacloprid in commercial formulation and residual Imidacloprid in tomato grown in greenhouse (protected cultivation) was also conducted. The results obtained from commercial formulation were completely consistent with those obtained through the standard high‐performance liquid chromatography (HPLC) method.     

Amperometric determination of thiosulfate at a surface-renewable nickel(II) hexacyanoferrate-modified carbon ceramic electrode

Graphite powder-supported nickel(II) hexacyanoferrate (NiHCF) was prepared by the in situ chemical deposition method and then dispersed into methyltrimethoxysilane-derived gels to form a conductive composite. The composite was used as electrode material to construct a surface-renewable three-dimensional NiHCF-modified carbon ceramic electrode. Electrochemical behavior of the chemically modified electrode was well characterized using cyclic and square-wave voltammetry. The electrode presented a good electrocatalytic activity toward the oxidization of thiosulfate and thus was used as an amperometric sensor for thiosulfate in the photographic waste effluent. In addition, the electrode exhibited a distinct advantage of surface-renewal by simple mechanical polishing, as well as simple preparation, good chemical and mechanical stability.     

An amperometric biosensor based on the coimmobilization of horseradish peroxidase and methylene blue on a beta-type zeolite modified electrode

A new biosensor for the amperometric detection of hydrogen peroxide was developed based on the coimmobilization of horseradish peroxidase (HRP) and methylene blue on a beta-type zeolite modified glassy carbon electrode without the commonly used bovine serum albumin-glutaraldehyde. The intermolecular interaction between enzyme and zeolite matrix was investigated using FT-IR. The cyclic voltammetry and amperometric measurement demonstrated that methylene blue co-immobilized with HRP in this way displayed good stability and could efficiently transfer electrons between immobilized HRP and the electrode. The sensor responded rapidly to H2O2 in the linear range from 2.5 x 10(-6) to 4.0 x 10(-3) M with a detection limit of 0.3 microM. The sensor was stable in continuous operation.     

Amperometric sensor for L-ascorbic acid determination based on MnO2 bulk modified screen printed electrode

A simple biosensor constructed by bulk-modification of carbon ink with manganese dioxide as a mediator was investigated for its ability to serve as amperometric detector for L-ascorbic acid in hydrodynamic mode. The sensor could be operated at pH 5.0 (0.05 M phosphate buffer) and exhibited excellent reproducibility and stability. Optimization of measurement parameters such as applied working potential and pH value were studied in detail. The screen printed electrode exhibited a linear amperometric increase with the concentration of ¶L-ascorbic acid from 50 mg L^–1 to 250 mg L^–1 and gave a (LOD = 3σ) detection limit of 0.2 mg L^–1 (1.172 μmol L^–1). The manganese dioxide modified screen printed electrode shows long term stability.