Fluorimetric determination of hemoglobin using spiro form rhodamine B hydrazide in a micellar medium

A novel fluorimetric method for the determination of hemoglobin (Hb) using spiro form rhodamine B hydrazide (RBH) as fluorogenic reagent in the presence of sodium dodecylbenzene sulfonate (SDBS) surfactant micelles is described. The method employs the reaction of Hb with RBH, a colorless, non-fluorescent spirolactam hydrazide in SDBS micelles to generate highly fluorescent product rhodamine B and hence leads to a large increase in fluorescence intensity. The fluorescence increase is linearly related to the concentration of Hb in the range 0.2-12.0 nmol l⁻¹ with a detection limit of 0.086 nmol l⁻¹ (3σ). The optimal conditions for the detection of Hb are evaluated and the possible detection mechanism is also discussed. The proposed method has been applied to the determination of Hb in human blood.     

Sensitive and selective spectrofluorimetric determination of chromium(VI) in water by fluorescence enhancement

A new fluorogenic method for the selective and sensitive determination of chromium(VI) in acidic water using rhodamine B hydrazide was developed. This method was based on the oxidation of non-fluorescent rhodamine B hydrazide by potassium dichromate in acidic aqueous conditions to give rhodamine B, which was highly fluorescent, as a product. With the optimum condition described, the fluorescence enhancement at 585 nm was linearly related to the concentration of chromium(VI) in the range of 5.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹ (2.60-104 ng mL⁻¹) with a correlation coefficient of R² = 0.9993 (n = 18) and a detection limit of 5.5 × 10⁻⁹ mol L⁻¹ (0.29 ng mL⁻¹). The R.S.D. was 2.2% (n = 5). The proposed method was also applied to the determination of chromium(VI) in drinking water, river water and synthetic samples.     

A new fluorescent probe of rhodamine B derivative for the detection of copper ion

A new fluorescent probe, rhodamine B hydrazide oxalamide (RBHO), which shows very weak fluorescence, was synthesized, and its fluorescence could be substantially enhanced by the addition of copper ion. The probe shows a high selectivity and sensitivity to copper ion by forming a 1:1 complex in acetonitrile, and the chelating is reversible. Limit of detection for copper ion in acetonitrile was found to be 3.7 × 10⁻⁸ mol L⁻¹. It was also found that copper ion could catalyze the hydrolysis of the probe in 50% (v/v) buffered (10 mM Tris–HCl, pH 7.0) water/acetonitrile giving a highly fluorescent product, and the fluorescence detection of copper ion was developed in this neutral buffered media with a detection limit of 6.4 × 10⁻⁷ mol L⁻¹. Determination of copper ion in water and synthetic samples in the presence of different interfering metal ions was successfully carried out with the new probe RBHO.     

A new Cu~(2+)-induced color reaction of a rhodamine derivative N-(3-carboxy)acryloyl rhodamine B hydrazide

A new rhodamine derivative,N-(3-carboxy)acryloyl rhodamine B hydrazide(CARB),has been synthesized,and its unusual spectroscopic reaction with Cu2+ has been investigated.The derivative exhibits a rapid and reversible non-fluorescent absorption upon coordination to Cu2+,which is a rather unusual phenomenon for rhodamine B derivatives.Stoichiometric measurements using the Job's method and the molar ratio method reveal that one CARB molecule combines two Cu2+ ions,and the two Cu2+ ions play different roles:one ...     

Application of rhodamine B hydrazide as a new fluorogenic indicator in the highly sensitive determination of hydrogen peroxide and glucose based on the catalytic effect of iron(III)-tetrasulfonato-phthalocyanine

A sensitive, selective and rapid spectrofluorimetric method is proposed for the determination of hydrogen peroxide using rhodamine B hydrazide as a fluorogenic substrate catalyzed by iron(III)-tetrasulfonatophthalocyanine. It is based on the oxidation of rhodamine B hydrazide, a colorless, non-fluorescent spirolactam hydrazide, by hydrogen peroxide which generates the highly fluorescent product rhodamine B. Under optimum conditions, the responses for hydrogen peroxide were linear from 2.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹, with a detection limit of 3.7 × 10⁻⁹ mol L⁻¹ in a 3.5 min reaction period. It can easily be incorporated into the determination of biochemical substances that produce hydrogen peroxide under catalytic oxidation in the presence of their oxidase. The possibility has been tested for the determination of glucose in human sera as an example.     

HPLC determination of rhodamine B (C.I. 45170) in cosmetic products

Summary A method is proposed for the extraction, separation, identification and quantitative measurement of rhodamine B in cosmetics samples The colour is extracted with a solution of orthophosphoric acid in either water or DMF (depending on the type of cosmetic) adsorbed on a polyamide column, and then eluted with water and methanol. Further clean-up of the extract is performed by means of a Bond Elut C-18 cartridge, from which rhodamine B is eluted with methanol-water (82). The final eluate is examined by HPLC. Chromatography is performed on a C-18 column with a gradient elution from 5050 to 7030 of acetonitrile-water, containing 0.1 M sodium perchlorate, in 15 min. A diodearray detector enables peak purity analysis. The method gives recovery values of approximately 90%, or better, and the reproducibility is within 4%.     

Chemiluminescence behavior based on oxidation reaction of rhodamine B with cerium(IV) in sulfuric acid medium

The chemiluminescence (CL) of the rhodamine B (RhB)-cerium(IV) system was investigated by flow-injection. Rhodamine B was suggested to be a suitable chemiluminescent reagent in acidic conditions. When the concentration of rhodamine B was 100 mg l⁻¹ and cerium sulfate was 1.6 mmol l⁻¹ in sulfuric acid, the chemiluminescent intensity was found to be highest by using 0.3 mol l⁻¹ sulfuric acid as a carrier solution. The particular chemiluminescent system could tolerate such distinct acidic environments that it was utilized for detecting many compounds that are stable in acidic solutions. Furthermore, by virtue of IR, UV-Vis and luminescence spectroscopic measurements, the chemiluminescent behavior of rhodamine B was studied and a possible mechanism for this chemiluminescent reaction was proposed. The emitter was affirmed to be a radical species due to one of the oxidation products of RhB; the chemiluminescent emissive wavelength was about 425 nm.     

离子缔合物-萃取荧光光度法测定水中阴离子表面活性剂

在 0 .2 5 mol/L H2 SO4 溶液中 ,罗丹明 B与阴离子表面活性剂形成离子缔合物 ,氯仿萃取后 ,于 5 5 0 nm处激发 ,荧光波长为 60 0 nm,对于十二烷基硫酸钠的线性范围为 0 .0 2 5～ 0 .4mg/L,RSD<2 .6%。方法可用于河水及生活废水中 1 0 -7～ 1 0 -6mol/L 阴离子表面活性剂的测定     

Rapid flow injection method for the determination of sulfite in wine using the permanganate-luminol luminescence system

A simple, rapid and sensitive chemiluminescence method for the determination of sulfite has been developed by combining flow-injection analysis and its sensitizing effect on the known chemiluminescence emission produced by the oxidation of luminol in alkaline medium; in this work permanganate has been proposed as oxidizing reactive. The optimum conditions for the chemiluminescence emission were established. The chemiluminescence was proportional to the sulfite concentration over the range 1.6 × 10⁻⁵ and 4.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.7 × 10⁻⁶ mol L⁻¹ of sulfite. The method has been satisfactorily used for the determination of free and bound sulfite in wines.     

Separation and determination of some trivalent metal ions using rhodamine B grafted polyurethane foam

The incorporation of rhodamine B into polyurethane foam matrix was prepared by mixing the rhodamine B with polyol (polyether) prior to the addition of diisocyanate reagent to form the polyurethane foam material. Rhodamine B grafted polyurethane foam (Rod.B-PUF) was found to be very suitable for the separation and preconcentration of trivalent metal ions e.g. bismuth (III), antimony (III) and iron (III) from thiocyanate solutions. Bismuth and antimony were separated from concentrated acid medium (1–6 M H₂SO₄). Iron (III) was separated from pH 1 to 3. The kinetics of sorption of the Bi (III), Sb (III) and Fe (III) onto the Rod.B-PUF was found to be fast, the extraction is accomplished from 5 to 10 min with average values of half-life of sorption (t_1/2) of 2.9 min. The average values of the Gibbs free energy (ΔG) for the sorption of metal ions onto Rod.B-PUF are ?6.6 kJ mol^?1, which reflect the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Rod.B-PUF was also discussed.     

Evaluation of a spectrofluorimetric method for the selective determination of thalidomide in pharmaceutical tablets, urine and blood serum

A spectrofluorimetric analytical methodology for the determination of thalidomide in pharmaceutical formulations, blood serum and urine was developed and evaluated in terms of sensibility and selectivity. Efforts were spent on the maximization of thalidomide fluorescence signal and on the increasing of selectivity when analyzing complex samples, specially, in samples containing sulfanilamide, a strongly fluorescent concomitant that can be used in association with thalidomide. Maximum signal was observed with optimized composition of the solvent system and pH. Approaches to enable selective determination of thalidomide in the presence of sulfanilamide were tested and compared. Better results were achieved using the combined use of acidic medium and UV treatment. For urine and blood serum samples, a solid phase extraction (on a C₁₈ cartridge) was found to be practical, enabling good recovery results. Limit of detection (3S_b/m) was estimated to be 1.2 μg l⁻¹, approximately 100 times better than the ones reported for the routine UV absorption HPLC methods. This low-cost spectrofluorimetric methodology was found to be very simple and enabled excellent recoveries when analyzing analyte spiked biological fluids as well as thalidomide based commercial and laboratory made pharmaceutical formulations.     

Kinetic studies of the polymerization of an epoxy resin modified with rhodamine B

Novel fluorescent materials were satisfactorily synthesized. With this aim, an epoxy resin based on diglycidyl ether of bisphenol A (DGEBA) was reacted with a laser dye, rhodamine B (RB), to achieve an epoxy-based prepolymer. Then, a diamine, m-xylylenediamine (MXDA), was used as hardener with the purpose of obtaining a crosslinked polymer. The curing conditions strongly influence the intended final properties and the optimization of the curing requires a reliable kinetic model. For that reason, this work presents the kinetic study of the polymerization of the epoxy resin by differential scanning calorimetry (DSC) in isothermal mode as well as by Fourier transform infrared spectroscopy (FTIR). DSC data were fitted using a Kamal autocatalytic equation. Conversion as a function of reaction time curves obtained by means of both techniques agreed well. In addition, the synthesized epoxy-based materials were characterized by proton nuclear magnetic resonance spectroscopy (¹H NMR) and their fluorescent properties were also analysed.     

Micelle-mediated cloud point extraction and spectrophotometric determination of rhodamine B using Triton X-100

A new micelle-mediated cloud point extraction method is described for sensitive and selective determination of trace amounts of rhodamine B by spectrophotometry. The method is based on the cloud point extraction of rhodamine B from aqueous solution using Triton X-100 in acidic media. The extracted surfactant rich phase is diluted with water and its absorbance is measured at 563 nm by a spectophotometer. The effects of different operating parameters such as concentration of surfactant and salt, temperature and pH on the cloud point extraction of rhodamine B were studied in details and a set of optimum conditions were obtained. Under optimum conditions a linear calibration graph in the range of 5-550 ng mL⁻¹ of rhodamine B in the initial solution with r = 0.9991 (n = 15) was obtained. Detection limit based on three times the standard deviation of the blank (3S_b) was 1.3 ng mL⁻¹ (n = 10) and the relative standard deviation (R.S.D.) for 50 and 350 ng mL⁻¹ of rhodamine B was 2.40 and 0.87% (n = 10), respectively. The method was applied for the determination of rhodamine B in soft pastel, hand washing liquid soap, matches tip and textile dyes mixture samples.     

Rapid one-step derivatization of Se(VI) to a piazselenol for the spectrofluorimetric determination of selenium in biological material

A spectrofluorimetric method for the determination of total selenium in biological samples has been developed. After oxidative destruction, the sample is reacted with a mixture of bromide and 2,3-diamino-1,4-dibromonaphthalene (Br₂-DAN) without pH adjustment. Selenium(VI) is rapidly reduced by bromide to Se(IV) which then forms 4,7-dibromo-5,6-benzopiazselenol (Br₂-DAN-Se). The conversion of Se(VI) to Br₂-DAN-Se is completed in 6 min at 100°C. The piazselenol is extracted to cyclohexane and the fluorescence measured at 577 nm with excitation at 518 nm. The procedure has been validated by determinations on reference materials with selenium concentrations ranging from 4 to 1460 ng g⁻¹. The advantages of the method are the fast reduction of Se(VI) by hydrobromic acid and the properties of Br₂-DAN, which permit the piazselenol formation to be carried out in a strongly acidic medium and at high temperature. The limit of detection is 0.6 ng g⁻¹ as estimated by three times the standard deviation of the blank determination (n = 7).

The rate of reduction of Se(VI) to Se(IV) in hydrobromic acid was investigated as a function of concentration and temperature. The new kinetic data together with previous kinetic and equilibrium data for the piazselenol formation were used to model and optimize the simultaneous reduction-derivatization procedure.     

利血平与玫瑰精B的高灵敏显色反应及分析应用

研究了利血平与玫瑰精B的显色反应,建立了测定利血平的高灵敏分光光度法。在酸性条件下,利血平的水解产物和玫瑰精B形成具有正、负吸收峰的红色离子缔合物,最大正吸收波长位于490 nm,最大负吸收波长位于520 nm,表观摩尔吸光系数(ε)分别为1.20×105L.mol-1.cm-1(正吸收)和1.83×105L.mol-1.cm-1(负吸收),利血平在0～5.0μg/mL范围内遵从比尔定律。若采用正、负峰叠加测定,灵敏度可达3.00×105L.mol-1.cm-1。探讨了适宜的反应条件、主要分析特性及方法的精密度和可靠性。该法可用于市售利血平注射液中利血平含量的测定。     

罗丹明B-过氧乙酸-氢氧化钠化学发光法测定痕量硫

基于硫离子对罗丹明B 过氧乙酸 NaOH化学发光有较强的增敏作用,建立了流动注射化学发光增强法测定痕量硫的新方法。该法的线性范围为3.0×10-8～8.0×10-7g/mL,检出限为3.5ng/mL,相对标准偏差为2.2%(1.0×10-7g/mLS2-,n=11)。此法已用于环境水样中痕量硫的测定。     

A novel spectrophotometric method for batch and flow injection determination of sulfite in beverages

A novel spectrophotometric assay method for batch and flow injection determination of sulfite in beverages is described. The method involves a reaction with diaquacobyrinic acid heptamethyl ester (diaquacobester, DACbs) in acetate buffer of pH 3 to form a highly stable sulfite cobester complex (SO₃Cbs). In the absence of sulfite, the reagent displays three absorption maxima at 349, 409 and 525 nm. Addition of sulfite is associated with the development of a new absorption band at 313 nm, an increase in the intensity of the band at 425 nm and a decrease in the absorbance of the bands at 349 and 525 nm. Variations of the absorptions at 313, 349, 425 and 525 nm are linearly proportional to sulfite concentrations over the range of 0.05–25 μg ml⁻¹with a detection limit of 0.01–0.2 μg ml⁻¹. Negligible interferences are caused by most common ions. Validation of the method according to the quality assurance standards shows suitability for quality control assessment of sulfite in complex matrices without prior treatment. The method has the advantages of high selectivity, good sensitivity, fast reaction, high stability of the reagent and reaction product and absorbance measurements at four different wavelengths in the same run. The method is successfully applied to determine the sulfite contents of some beverages. The results compare fairly well with data obtained using the standard method.     

Direct determination of sulfite in food samples by a biosensor based on plant tissue homogenate

In the work described here, a biosensor was developed for the determination of sulfite in food. Malva vulgaris tissue homogenate containing sulfite oxidase enzyme was used as the biological material. M. vulgaris tissue homogenate was crosslinked with gelatin using glutaraldehyde and fixed on a pretreated Teflon membrane. Sulfite was enzymatically converted to sulfate in the presence of the dissolved oxygen, which was monitored amperometrically. Sulfite determination was carried out by standard curves, which were obtained by the measurement of consumed oxygen level related to sulfite concentration. Several operational parameters had been investigated: the amounts of plant tissue homogenate and gelatin, percentage of glutaraldehyde, optimum pH and temperature. Also, some characterization studies were done. There was linearity in the range between 0.2 and 1.8 mM at 35 °C and pH 7.5. The results of real sample analysis obtained with the biosensor agreed well with the enzymatic reference method using spectrophotometric detection.     

A new and sensitive resonance-scattering method for determination of trace nitrite in water with rhodamine 6G

In the medium HCl–KI–rhodamine dye, NO₂^– reacts with excess I^– to form I₃^– and the I₃^– and rhodamine dye combine to form an association particle which gives three resonance-scattering (RS) peaks at 320 nm, 400 nm, and 595 nm. In systems containing rhodamine 6G (Rh6G), rhodamine B (RhB), rhodamine S (RhS), and butyl rhodamine B (BRhB) the resonance scattering intensity at 400 nm is proportional to nitrite concentrations in the range 2.3–276 ng mL^–1, 9.2–184 ng mL^–1, 9.2–184 ng mL^–1, and 9.2–92 ng mL^–1, respectively. Because of the high sensitivity, wide linear range, and good stability of the Rh6G system, it has been used for determination of nitrite in water samples, with satisfactory results. The spectral results have been used to verify that the formation of (Rh6G·I₃)_n association particles and their interface with the system are main factors that cause the RS enhancement.