Characteristics of subtractive anodic stripping voltammetry of Pb and Cd at silver and gold electrodes

Silver and gold electrodes are useful for the quantitative determination of lead and cadmium with subtractive anodic stripping voltammetry (SASV). The use of SASV is essential for achieving good separation between the two peaks, to eliminate the interference of nitrates when cadmium is present and to allow analysis at very low concentrations without the removal of oxygen. The deposition and dissolution of Pb²⁺ and Cd²⁺ proceed at underpotential (UPD) on both electrodes. The UPD properties of the deposits are the main factor determining the analytical characteristics of the ASV method and are strongly affected by the type and concentration of the electrolyte. The effects of anions (Cl⁻, Br⁻, SO₄²⁻, NO₃⁻) and acids (HNO₃, HClO₄, H₂SO₄, HCl) are shown. The two electrodes complement each other and, in addition, enable the qualitative identification of Pb²⁺ and Cd²⁺, since the peaks appear in opposite order on the two electrodes. Analysis of mixtures of the two analytes is restricted on gold but not on silver. At gold the two peaks overlap: (i) at concentrations of cadmium higher than 250 nM at deposition times greater than 30 s, (ii) in the presence of copper at concentrations higher than 1 μM, and (iii) in the presence of Triton X-100 at concentrations above 10 mg/l. The repeatability at 10 nM analyte is better than 2.5%. The detection limits for Pb²⁺ and Cd²⁺ at 120 s deposition time and 3500 rpm rotation rate are: dl_Pb/Ag=0.04 nM; dl_Cd/Ag=0.7 nM; dl_Pb/Au=0.1 nM; dl_Cd/Au=0.3 nM. The analysis of lead and cadmium in natural waters has been performed.     

The renovated silver ring electrode in determination of lead traces by differential pulse anodic stripping voltammetry

The study of a new type of working electrode - the renovated silver ring electrode (RSRE) - for lead ions detection via differential pulse anodic stripping voltammetry (DP ASV) without removal of oxygen is reported. The only four constituents of the RSRE: a specially constructed silver ring electrode, a silver sheet used as silver counter/quasi-reference electrode and a silicon O-ring, are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RSRE body. Excellent repeatability and reproducibility - also in organic samples solutions - were reached in a period of a few weeks through the renovation of the electrode surface before each measurement. The reduction and stripping of lead on silver electrode under the DP ASV conditions are underpotential deposition/dissolution phenomena. The RSRE is used for the determination of Pb ions in concentrations ranging from 1 × 10⁻⁹ to 1 × 10⁻⁷ M. The repeatability of DP ASV runs in synthetic solutions covering the entire concentration range is better than 2%. Obtained calibration curves are represented by a correlation coefficient of at least 0.999. The detection limit (LOD) for the time of electrodeposition equal to 60 s is 0.2 × 10⁻⁹ M. LOD for Pb²⁺ detection at the RSRE is similar to this reported for a rotating silver electrode in subtractive anodic stripping voltammetry (E. Kirowa-Eisner, et al., Anal. Chim. Acta, 385 (1999) 325). The analysis of Pb²⁺ in synthetic solutions with and without surfactants, certified reference materials and natural water samples have been performed.     

Voltammetry of lead cations on a new type of silver composite electrode in the presence of other cations

A new type of silver composite electrode was examined, prepared from silver, graphite powder, and methacrylate resin. The effects of the presence of various cations (cadmium, copper, bismuth, thallium), anions (chlorides), surface-active substances (Triton X-100), and oxygen on the anodic-stripping voltammetric determination of lead were studied. It was found that the effect of underpotential deposition at the composite electrode differs from that produced at a metallic silver electrode, mainly at low concentrations of the deposited metal. The use of this type of silver composite electrode in differential pulse anodic-stripping voltammetry enables direct determination of lead in natural water samples without elimination of surface-active substances (LOD about 3 g L^–1).     

Determination of arsenate in natural pH seawater using a manganese-coated gold microwire electrode

Direct electrochemical determination of arsenate (As^V) in neutral pH waters is considered impossible due to electro-inactivity of As^V. As^III on the other hand is readily plated as As⁰ on a gold electrode and quantified by anodic stripping voltammetry (ASV). We found that the reduction of As^V to As^III was mediated by elemental Mn on the electrode surface in a novel redox couple in which 2 electrons are exchanged causing the Mn to be oxidised to Mn^II. Advantage is taken of this redox couple to enable for the first time the electrochemical determination of As^V in natural waters of neutral pH including seawater by ASV using a manganese-coated gold microwire electrode. Thereto Mn is added to excess (∼1 μM Mn) to the water leading to a Mn coating during the deposition of As on the electrode at a deposition potential of −1.3 V. Deposition of As⁰ from dissolved As^V caused elemental Mn to be re-oxidised to Mn^II in a 1:1 molar ratio providing evidence for the reaction mechanism. The deposited As^V is subsequently quantified using an ASV scan. As^III interferes and should be quantified separately at a more positive deposition potential of −0.9 V. Combined inorganic As is quantified after oxidation of As^III to As^V using hypochlorite. The microwire electrode was vibrated during the deposition step to improve the sensitivity. The detection limit was 0.2 nM As^V using a deposition time of 180 s.     

Characteristics of Subtractive Anodic Stripping Voltammetry of Lead,Cadmium and Thallium at Silver‐Gold Alloy Electrodes

Silver‐gold alloy electrodes have been studied for the purpose of the quantitative determination of heavy metals by subtractive anodic stripping voltammetry, (SASV). The results have been compared with those obtained with the silver and gold electrodes. The 50/50 a/o Ag/Au alloy electrode is the most suitable for quantifying thallium in the presence of lead and cadmium. The separation of its peak from those of lead and cadmium is 200 mV, which is about twice the separation obtained on the pure metal electrodes and is also better than on mercury. The silver electrode is suitable for the simultaneous determination of thallium, lead and cadmium. The peaks of lead and cadmium overlap on the 50/50 alloy. Pure silver or pure gold can be used for simultaneous quantification of these two metals. The use of gold for quantifying lead and cadmium is more limited because the peak potential of cadmium is shifted in the negative direction as its concentration increases and at [Cd²⁺]>200 nM, the two peaks merge. SASV enables correction for background currents and is of utmost importance for obtaining well‐defined peaks. The peaks of lead, cadmium and thallium appear over a relatively narrow potential range (ca. 200 mV) on all the electrodes presented in this work. For this reason, the quantifying of a peak is based on the derivative at the inflection point of only one of its branches (ascending or descending). All SASV measurements were carried out without removal of oxygen.     

Determination of cadmium with a sequential injection lab-on-valve by anodic stripping voltammetry using a nafion coated bismuth film electrode

This work exploited a sequential injection lab-on-valve (LOV) system for the determination of cadmium by anodic stripping voltammetry (ASV). A miniaturized electrochemical flow cell (EFC) was fabricated in LOV, in which a nafion coated bismuth film electrode was used as working electrode. The cadmium was electrodeposited on the electrode surface in bismuth solution, and measured with the subsequential stripping scan. Under optimal conditions, the proposed system responded linearly to cadmium concentrations in a range 2.0-100.0 μg L⁻¹. The detection limit of this method was found to be 0.88 μg L⁻¹. By loading a sample volume of 800 μL, a sampling frequency of 22 determinations h⁻¹ was achieved. The repeatability expressed as relative standard derivation (R.S.D.) was 3.65% for 20 μg L⁻¹ cadmium (n = 11). The established method was applied to analysis of trace cadmium in environmental water samples and the spiked recoveries were satisfactory.     

Mercury-free simultaneous determination of cadmium and lead at a glassy carbon electrode modified with multi-wall carbon nanotubes

A multi-wall carbon nanotube (MWNT) modified glassy carbon electrode (GCE) was described for the simultaneous determination of trace levels of cadmium and lead by anodic stripping voltammetry (ASV). In pH 4.5 NaAc-HAc buffer containing 0.02 mol/l KI, Cd²⁺ and Pb²⁺ first adsorb onto the surface of a MWNT film coated GCE and then reduce at −1.20 V. During the positive potential sweep, reduced cadmium and lead were oxidized, and two well-defined stripping peaks appeared at −0.88 and −0.62 V. Compared with a bare GCE, a MWNT film coated GCE greatly improves the sensitivity of determining cadmium and lead. Low concentration of I⁻ significantly enhances the stripping peak currents since it induces Cd²⁺ and Pb²⁺ to adsorb at the electrode surface. The striping peak currents change linearly with the concentration of Cd²⁺ from 2.5×10⁻⁸ to 1×10⁻⁵ mol/l and with that of Pb²⁺ from 2×10⁻⁸ to 1×10⁻⁵ mol/l. The lowest detectable concentrations of Cd²⁺ and Pb²⁺ are estimated to be 6×10⁻⁹ and 4×10⁻⁹ mol/l, respectively. The high sensitivity, selectivity, and stability of this MWNT film coated electrode demonstrated its practical application for a simple, rapid and economical determination of trace levels of Cd²⁺ and Pb²⁺ in water samples.     

Optimisation of mercury film deposition on glassy carbon electrodes: evaluation of the combined effects of pH, thiocyanate ion and deposition potential

The combined effects of pH, thiocyanate ion and deposition potential in the characteristics of thin mercury film electrodes plated on glassy carbon surfaces are evaluated. Charges of deposited mercury are used as an experimental parameter for the estimation of the effectiveness of the mercury deposition procedure. The sensitivity of the anodic stripping voltammetry (ASV) method for the determination of lead at in situ and at ex situ formed thin mercury films are also examined. It was concluded that, in acidic solutions (pH 2.5-5.7) and fairly negative deposition potentials, e.g. −1.3 to −1.5 V, thiocyanate ion promotes the formation of the mercury film, in respect both to the amount of deposited mercury and to the mercury deposition rate. Also, the mercury coatings produced in thiocyanate solutions are more homogeneous, as depicted by microscopic examinations. In the presence of thiocyanate there is no obvious advantage of using high concentrations of mercury and/or high deposition times for the in situ and ex situ preparation of the mercury film electrodes. The optimised thin mercury film electrode ex situ prepared in a 5.0 mM thiocyanate solution of pH 3.4 was successfully applied to the ASV determination of lead and copper in acidified seawater (pH 2). The limit of detection (3σ) was 6×10⁻¹¹ M for lead and 2×10⁻¹⁰ M for copper for a deposition time of 5 min. Relative standard deviations (R.S.D.s) of <1.2% were obtained for determinations at the nanomolar of concentration level.     

Silver UPD ultra-thin film modified nanoporous gold electrode with applications in the electrochemical detection of chloride

Nanoporous noble metals are usually expected to exhibit much higher surface areas than smooth ones, making them of particular importance in many electrochemical applications. This paper describes a simple electrochemical method to modify a nanoporous Au (NPG) surface by using an under potentially deposited (UPD) Ag adlayer. The NPG electrode was obtained by the dealloying of Zn from Au_xZn_1−x in a 40-60 mol% zinc chloride-1-ethyl-3-methylimidazolium chloride (ZnCl₂-EMIC) ionic liquid. The Ag UPD modified nanoporous gold (NPG/Ag(UPD)) electrode possessed dual properties, including an intrinsic high surface area from the nanoporous structure and the characteristics of the Ag UPD adlayer. The potential utility of using NPG/Ag(UPD) for sensors was demonstrated by its excellent sensitivity and selectivity in the electrochemical determination of chloride ions. An atomic scale metal monolayer obtained in the UPD process was selected as a sensing agent. The long-term storability and operational stability of the electrode were strongly demonstrated. Specifically, two couples of redox waves at ∼552 mV and ∼272 mV, respectively, were observed in the cyclic voltammograms (CVs) of the NPG/Ag(UPD) after the adsorption of chloride ions. The first couple of redox waves was related to the UPD and silver stripping and the second couple of redox waves was induced by the adsorption of Cl⁻. The Cl⁻ adsorption process on the NPG/Ag(UPD) electrode followed the transient Langmuir adsorption kinetic model. The ratio of the integrated charges for these two anodic stripping peaks was selectively used to determine dilute chloride ion levels. The calibration curve was linear in the Cl⁻ concentration range of 0.5-30.0 μM.     

Simultaneous determination of copper and lead in seawater using optimised thin-mercury film electrodes in situ plated in thiocyanate media

In the present work the anodic stripping voltammetric (ASV) methodology using a thin mercury film electrode in situ plated in thiocyanate media was re-assessed in order to allow the simultaneous determination of copper and lead in seawater. Under previously suggested conditions [6], i.e. using a concentration of thiocyanate of 5 mM, the ASV peaks of copper and lead overlapped due to the formation of a stable copper(I)-thiocyanate species, limiting the analytical determinations. Therefore, the best value for the thiocyanate concentration was re-evaluated: for 0.05 mM a trade-off between good resolution of the copper and lead peaks and high reproducibility of the mercury film formation/removing processes was achieved. In this media, the ASV peaks for Pb and Cu occurred, separated by 140 mV. Also, the in situ thin mercury film electrode was produced and removed with good repeatability, which was confirmed by the relative standard deviation values for the ASV determinations: 0.5% for Pb and 2.0% for Cu (10 replicate determinations in a solution with metal concentrations 1.5×10⁻⁸ M for lead and 2.2×10⁻⁸ M for copper). The optimised methodology was successfully applied to the determination of copper in the presence of lead, in certified seawater (NASS-5).     

Determination of arsenic and antimony in seawater by voltammetric and chronopotentiometric stripping using a vibrated gold microwire electrode

The oxidation potentials of As⁰/As^III and Sb⁰/Sb^III on the gold electrode are very close to each other due to their similar chemistry. Arsenic concentration in seawater is low (10–20 nM), Sb occurring at ∼0.1 time that of As. Methods are shown here for the electroanalytical speciation of inorganic arsenic and inorganic antimony in seawater using a solid gold microwire electrode. Anodic stripping voltammetry (ASV) and chronopotentiometry (ASC) are used at pH ≤ 2 and pH 8, using a vibrating gold microwire electrode. Under vibrations, the diffusion layer size at a 5 μm diameter wire is 0.7 μm. The detection limits for the As^III and Sb^III are below 0.1 nM using 2 min and 10 min deposition times respectively. As^III and Sb^III can be determined in acidic conditions (after addition of hydrazine) or at neutral pH. In the latter case, oxidation of As⁰ to As^III was found to proceed through a transient As^III species. Adsorption of this species on the gold electrode at potentials where Sb^III diffused away is used for selective deposition of As^III. Addition of EDTA removes the interfering effect of manganese when analysing As^III. Imposition of a desorption step for Sb^III analysis is required. Total inorganic arsenic (iAs = As^V + As^III) can be determined without interference from Sb nor mono-methyl arsenious acid (MMA) at 1.6 < pH < 2 using E_dep = −1 V. Total inorganic antimony (iSb = Sb^V + Sb^III) is determined at pH 1 using E_dep = −1.8 V without interference by As.     

Nafion/2,2'-bipyridyl-modified bismuth film electrode for anodic stripping voltammetry

This paper describes the fabrication, characterisation and the application of a Nafion/2,2′-bipyridyl/bismuth composite film-coated glassy carbon electrode (NC(Bpy)BiFE) for the anodic stripping voltammetric determination of trace metal ions (Zn²⁺, Cd²⁺ and Pb²⁺). The NC(Bpy)BiFE electrode is prepared by first applying a 2.5 mm³ drop of a coating solution containing 0.5 wt% Nafion and 0.1% (w/v) 2,2′-bipyridil (Bpy) onto the surface of a glassy carbon electrode, while the Bi film was plated in situ simultaneously with the target metal ions at −1.4 V. The main advantage of the polymer coated bismuth film electrode is that the sensitivity of the stripping responses is increased considerably due to the incorporation of the neutral chelating agent of 2,2′-bipyridyl (Bpy) in the Nafion film, while the Nafion coating improved the mechanical stability of the bismuth film and its resistance to the interference of surfactants. The key experimental parameters relevant to both the electrode fabrication and the voltammetric measurement were optimized on the basis of the stripping signals. With a 2 min deposition time in the presence of oxygen, linear calibration curves were obtained in a wide concentration range (about 2-0.001 μM) with detection limits of 8.6 nM (0.56 μg dm⁻³) for Zn²⁺, 1.1 nM (0.12 μg dm⁻³) for Cd²⁺ and 0.37 nM (0.077 μg dm⁻³) for Pb²⁺. For nine successive preconcentration/determination/electrode renewal experiments the standard deviations were between 3 and 5% at 1.2 μM for zinc and 0.3-0.3 μM concentration level for lead and cadmium, respectively, and the method exhibited excellent selectivity in the presence of the excess of several potential interfering metal ions. The analytical utility of the stripping voltammetric method elaborated was tested in the assay of heavy metals in some real samples and the method was validated by ICP-MS technique.     

Ultrasensitive determination of silver ion based on synchronous fluorescence spectroscopy with nanoparticles

Based on the characteristics of synchronous fluorescence spectroscopy (SFS), a new method with high sensitivity and selectivity was developed for rapid determination of silver ion with functional cadmium sulphide (CdS) nanoparticles as a fluorescence probe. When Δλ (λ_em − λ_ex) = 215 nm, maximum synchronous fluorescence is produced at 304 nm. Under optimal conditions, functional cadmium sulphide displayed a calibration response for silver ion over a wide concentration range from 0.8 × 10⁻¹⁰ to 1.5 × 10⁻⁸ mol L⁻¹. The limit of detection was 0.4 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of seven replicate measurements for the lowest concentration (0.8 × 10⁻¹⁰ mol L⁻¹) was 2.8%. Compared with several fluorescence methods, the proposed method had a wider linear range and improved the sensitivity. Furthermore, the concentration dependence of the synchronous fluorescence intensity is effectively described by a Langmuir-type binding isotherm.     

Determination of cadmium, lead, copper and zinc in the acetic acid extract of glazed ceramic surfaces by anodic stripping voltammetric method

An anodic stripping voltammetric method has been developed for determination of cadmium, lead, copper and zinc in acetic acid extract of glazed ceramic surfaces. An aliquot of 4% (v/v) acetic acid solution was kept in a ceramic ware for 24 h in the dark, then 10 mL of the extracted solution was placed in a voltammetric cell. The solution was purged with oxygen free nitrogen gas for 3 min before deposition of the metals was carried out by applying a constant potential of −1.20 V versus Ag/AgCl to the hanging mercury drop electrode (HMDE) for 45 s. A square wave waveform was scanned from −1.20 to 0.15 V and a voltammogram was recorded. A standard addition procedure was used for quantification. Detection limits of 0.25, 0.07, 2.7 and 0.5 μg L⁻¹ for cadmium, lead copper and zinc, respectively, were obtained. Relative standard deviations for 11 replicate determinations of 100 μg L⁻¹ each of all the metals were in the range of 2.8-3.6%. Percentage recoveries obtained by spiking 50 μg L⁻¹ of each metal to the sample solution were in the range of 105-113%. The method was successfully applied to ceramic wares producing in Lampang province of Thailand. It was found that the contents of cadmium, lead, copper and zinc released from the samples were in the range of <0.01-0.16, 0.02-0.45, <0.14 and 0.28-10.36 μg dm⁻², respectively, which are lower than the regulated values of the Thai industrial standard. The proposed method is simpler, more convenient and more sensitive than the standard method based on FAAS.     

Determination of cadmium, lead and thallium in highly saline hemodialysis solutions by potentiometric stripping analysis (PSA)

Potentiometric stripping analysis (PSA) was investigated to assay simultaneously cadmium, lead and thallium present as contaminants in highly saline solutions used in hemodialysis. The saline matrices were sodium, potassium, magnesium and calcium chlorides, sodium acetate, sodium bicarbonate and glucose, which constitute concentrates for hemodialysis. A 1000 μg mL⁻¹ Hg(II) solution was used to prepare the mercury film electrode (MFE) and to carry out the stripping step. After a 30 s accumulation interval the analytes were simultaneously detected in the saline matrices without using masking agents. Determination limits of 80 ng L⁻¹ for cadmium and thallium, and 50 ng L⁻¹ for lead were calculated and a R.S.D. ranging from 0.5 to 2.2% (n = 3) was obtained measuring the analytes directly in commercial hemodialysis saline solutions. Recoveries from spiked samples ranging from 94.6 to 102.0% were obtained. The investigated metals were found in concentrations ranging from 2.7 to 5.7 μg L⁻¹ for cadmium, 27.7 to 75.8 μ L⁻¹ for lead and 9.6 to 18.7 μg L⁻¹ for thallium in commercial hemodialysis solutions. The PSA method showed to be adequate to the quality control of saline concentrates for hemodialysis.     

Sequential injection monosegmented flow voltammetric determination of cadmium and lead using a bismuth film working electrode

A cost-effective sequential injection monosegmented flow analysis (SI-MSFA) with anodic stripping voltammetric (ASV) detection has been developed for determination of Cd(II) and Pb(II). The bismuth film working electrode (BiFE) was employed for accumulative preconcentration of the metals by applying a fixed potential of −1.10 V versus Ag/AgCl electrode for 90 s. The SI-MSFA provides a convenient means for preparation of a homogeneous solution zone containing sample in an acetate buffer electrolyte solution and Bi(III) solution for in situ plating of BiFE, ready for ASV measurement at a flow through thin layer electrochemical cell. Under the optimum conditions, linear calibration graphs in range of 10-100 μg L⁻¹ of both Cd(II) and Pb(II) were obtained with detection limits of 1.4 and 6.9 μg L⁻¹ of Cd(II) and Pb(II), respectively. Relative standard deviations were 2.7 and 3.1%, for 11 replicate analyses of 25 μg L⁻¹ Cd(II) and 25 μg L⁻¹ Pb(II), respectively. A sample throughput of 12 h⁻¹ was achieved with low consumption of reagent and sample solutions. The system was successfully applied for analysis of water samples collected from a draining pond of zinc mining, validating by inductively coupled plasma-optical emission spectroscopy (ICP-OES) method.     

Antimony-film electrode for the determination of trace metals by sequential-injection analysis/anodic stripping voltammetry

The possibility of applying antimony-film modified glassy carbon electrode in sequential-injection analysis (SIA) was investigated with the objective of determining Pb(II) and Cd(II) by anodic stripping voltammetry (ASV). The conditions of antimony-film deposition concerning composition of the plating/carrier solutions, concentrations of Sb(III) and hydrochloric acid, effects of different supporting electrolyte salts, and plating potential were optimized. It was found that the antimony-film deposition on glassy carbon substrate in a sample solution consisting of 750 μg L⁻¹ Sb(III), 0.5 mol L⁻¹ HCl at −1.5 V (vs. Ag/AgCl/3 mol L⁻¹ KCl) yielded a modified electrode suitable for the determination of Pb(II) and Cd(II) at the μg L⁻¹ level. The reproducibility of the analytical signals was characterized by a relative standard deviation lower than 2.8%, and the calculated values of detection limits were 1.2 μg L⁻¹ for Pb(II) and 1.4 μg L⁻¹ for Cd(II). The presence of KSCN in the sample solution offers the possibility of detecting ions with more negative oxidation potentials like Zn(II), Mn(II) or Cr(III). The developed SIA-ASV procedure was compared with the commonly used batch method, and its applicability was tested on a spiked tap water sample.     

Determination of arsenic in gold samples using matrix exchange differential pulse stripping voltammetry

A method comprising matrix exchange differential pulse stripping voltammetry (DPSV) at a gold film electrode has been proposed for the determination of small quantities of arsenic in pure gold. A wall-jet cell (WJC) and an on-line deoxygenation system were used to facilitate matrix exchange. The gold(I) cyanide complex was formed to avoid gold deposition on the electrode together with the arsenic. The pH of the sample solutions were adjusted to 3, as alkaline solutions gold(I) cyanide produced interference and the uncomplexed cyanide led to passivation of the gold film electrode. Matrix exchange electrolytes consisting of 4 mol l⁻¹ hydrochloric acid or a combination of 2 mol l⁻¹ sulphuric acid and 0.2 mol l⁻¹ hydrochloric acid could be utilised. Arsenic concentrations as low as 0.1 mg l⁻¹, could readily be detected in a gold matrix with a 60 s deposition time. While, cobalt and silver did not interfere with the arsenic determination, copper interfered even when present at similar concentrations to that of arsenic.     

Preconcentration of palladium in a flow-through electrochemical cell for determination by graphite furnace atomic absorption spectrometry

An electrochemical preconcentration at a controlled potential on the electrode in a flow-through mode followed by graphite furnace atomic absorption spectrometric (GFAAS) detection is proposed for determination of trace amounts of palladium. After electrolysis the polarization of the electrodes was changed and deposited metal was dissolved electrochemically in the presence of an appropriate stripping reagent. Conditions for the electrodeposition, such as pH of the solutions, a deposition potential, dissolution potential and a composition of stripping solution were optimised. The graphite electrode (GE) and glassy carbon electrode (GCE) were tested for the palladium reduction process. The detection limit of 0.05 ng ml⁻¹ Pd (1 pg) was obtained after palladium preconcentration on the GCE and dissolution with 0.2 mol l⁻¹ thiourea in 0.1 mol l⁻¹ HCl followed by GFAAS detection. The method was applied for the determination of palladium in spiked tap water and road dust samples.     

Stripping voltammetry of silver ions at polythiophene-modified platinum electrodes

The present work describes the development of a modified platinum electrode for stripping voltammetric determination of silver. The deposition of films based on electropolymerisation of the monomer thiophene was carried out by cycling the potential towards positive values between 0 and 1.6 V.The preconcentration process of silver ions was initiated on the surface of the modified electrode by complexing silver with polythiophene (PTH) when a negative potential (−0.5 V) was applied; then the reduced products was oxidized by means of differential pulse stripping voltammetry and the peak was observed at 0.17 V. Parameters such as pH, supporting electrolyte and number of electropolymerisation cycles were studied. A linear relation between current peak and concentration of Ag(I) was obtained in the range 0.07-1.0 mg L⁻¹. The detection limit for Ag(I) was evaluated to be 0.06 mg L⁻¹. The reproducibility was tested carrying out 11 measurements at different electrodes and the relative standard deviation was 1.5%. The interference of several metals was investigated and showed negligible effect on the electrode response.