A dual-electrolyte rechargeable Li-air battery with phosphate buffer catholyte

A novel dual-electrolyte rechargeable Li-air cell, consisting of lithium metal anode in an aprotic electrolyte, an air electrode in an aqueous phosphate buffer catholyte, and a NASICON-type lithium-ion conducting solid electrolyte (Li_{1 + x + y}Al_xTi_2 − xSi_yP_3 − yO₁₂ or LTAP) separator, has been investigated. The solid electrolyte separates the aprotic electrolyte from the aqueous catholyte, while providing pathways for lithium-ion transport. The phosphate buffer solution with a moderate pH helps to keep the solid electrolyte stable and reduces internal resistance and overpotential, while enabling a rechargeable Li-air cell with a high operating voltage and energy density. The Li-air cell exhibits a discharge capacity of 221 mAh g^− 1 at a current density of 0.5 mA cm^− 2 with good cycle life.     

Selective detection and recovery of gold at tannin-immobilized non-conducting electrode

A tannin-immobilized glassy carbon electrode (TIGC) was prepared via electrochemical oxidation of the naturally occurring polyphenolic mimosa tannin, which generated a non-conducting polymeric film (NCPF) on the electrode surface. The fouling of the electrode surface by the electropolymerized film was evaluated by monitoring the electrode response of ferricyanide ions as a redox marker. The NCPF was permselective to HAuCl₄, and the electrochemical reduction of HAuCl₄ to metallic gold at the TIGC electrode was evaluated by recording the reduction current during cyclic voltammetry measurement. In the mixed electrolyte containing HAuCl₄ along with FeCl₃ and/or CuCl₂, the NCPF remained selective toward the electrochemical reduction of HAuCl₄ into the metallic state. The chemical reduction of HAuCl₄ into metallic gold was also observed when the NCPF was inserted into an acidic gold solution overnight. The adsorption capacity of Au(III) on tannin-immobilized carbon fiber was 29 ± 1.45 mg g⁻¹ at 60 °C. In the presence of excess Cu(II) and Fe(III), tannin-immobilized NCPF proved to be an excellent candidate for the selective detection and recovery of gold through both electrochemical and chemical processes.     

A tetraethylene glycol dimethylether-lithium bis(oxalate)borate (TEGDME-LiBOB) electrolyte for advanced lithium ion batteries

Tetraethylene glycol dimethylether-lithium bis(oxalate)borate (TEGDME-LiBOB) electrolyte is here studied. Electrochemical impedance spectroscopy (EIS) measurements demonstrate that the electrolyte has conductivity higher than 10^− 3 S cm^− 1 at room temperature and about 10^− 2 S cm^− 1 at 60 °C, while thermogravimetry indicates a stability extending up to 180 °C. Sweep voltammetry of the electrolyte shows anodic stability extending over 4.6 V vs. Li and cathodic peak at about 1.5 V vs. Li/Li⁺, caused by a decomposition of LiBOB salt, and following prevented by using a pre-treated Sn-C anode. Furthermore, LiFePO₄ electrode is successfully used as cathode in a lithium cell using the TEGDME-LiBOB electrolyte. The promising electrochemical results, the low cost and the very high safety level candidate the electrolyte here reported as a valid alternative to the conventional electrolyte based on fluorinated salts presently used in the lithium ion battery field.     

Dynamic solid phase microextraction sampling for reactive terpenes in the presence of ozone

Dynamic gas sampling using solid phase microextraction (SPME) was evaluated for recovery of reactive terpenes and terpenoids in the presence of ozone. For limonene, α-terpineol and dihydromyrcenol in the 20-60 ppb range, this method achieves >80% recovery for ozone mixing ratios up to 100 ppb. Both the experimental results and a model analysis indicate that higher ozone concentrations and longer sampling times result in lower percent recovery. Typically greater than 90% recovery and ppb level method detection limits were achieved with a 5 min sample time. Increasing the flow rate from 100 to 400 sccm flow (5-20 cm s⁻¹) through the active sampler did not significantly affect sensitivity or recovery in most cases, probably due to negligible mass-transfer improvements. The recovery for each compound improves when sampling from a mixture of different species than that from a single compound sample. This may be due to competition for ozone amongst adsorbed species. Dynamic SPME sampling can improve detection and quantification of terpenes in reactive environments, especially for low vapor pressure (<5 mm Hg at 25 °C) compounds that can be adsorbed to ozone scrubbers used in other methods.     

Fast and direct determination of butylated hydroxyanisole in biodiesel by batch injection analysis with amperometric detection

We report here, for the first time, application of batch injection analysis (BIA) with amperometric detection for determination of the phenolic antioxidant butylated hydroxyanisole (BHA) in biodiesel. A sample plug was directly injected onto a boron-doped diamond electrode immersed in 50% v/v hydroethanolic solution with 0.1 mol L⁻¹ HClO₄ using an electronic micropipette. Importantly, the only preparation step required for biodiesel analysis is dilution in the same hydroethanolic electrolyte solution. Our proposed method has several advantages for routine biodiesel analysis, including: a low relative standard deviation between injections (0.29%, n = 20), high analytical frequency (120 h⁻¹), adequate recovery values (93-101%) for spiked samples, satisfactory accuracy (based on comparative determinations by high-performance liquid-chromatography), and a low detection limit (100 ng of BHA per g of biodiesel). Finally, our method can be adapted for the determination of other antioxidants in biodiesel samples.     

Nonenzymatic amperometric organic peroxide sensor based on nano-cobalt phthalocyanine loaded functionalized graphene film

An enzyme-free amperometric method was established for the electrochemical reduction tert-butyl hydroperoxide (TBHP) on the utilization of nano-cobalt phthalocyanine (CoPc) loaded functionalized graphene (FGR) and to create a highly responsive organic peroxide sensor. FGR was synthesized with a simple and fast method of electrolysis with potassium hexafluorophosphate (KPF₆) solution as electrolyte under the static current of 0.2 A. In the present work, FGR was dispersed in the solution of CoPc to fabricate chemical modified electrode to detect TBHP. The electro-reduction of TBHP can be catalyzed by FGR–CoPc, which has an excellent electrocatalytical activity due to the synergistic effect of the FGR with CoPc. The sensor can be applied to the quantification of TBHP with a linear range covering from 0.0260 to 4.81 mM, a high sensitivity of 13.64 A M⁻¹, and a low detection limit of 5 μM. This proposed sensor was designed as a simple, robust, and cheap analytical device for the determination of TBHP in body lotion.     

Physical and electrolytic properties of difluorinated dimethyl carbonate

The physical and electrolytic properties of difluorinated dimethyl carbonate (DFDMC) synthesized using F₂ gas (direct fluorination) were examined. The dielectric constant and viscosity of DFDMC are higher than those of monofluorinated dimethyl carbonate (MFDMC) and dimethyl carbonate (DMC). The oxidative decomposition voltage of DFDMC is higher than those of DMC and MFDMC. The specific conductivity in DFDMC solution is considerably lower than those in MFDMC and DMC solutions. The ethylene carbonate (EC)-DFDMC equimolar binary solution containing 1 mol dm⁻³ LiPF₆ shows a moderate conductivity of 6.91 mS cm⁻¹ at 25 °C. The lithium electrode cycling efficiency (charge-discharge coulombic cycling efficiency of lithium electrode) in EC-DFDMC equimolar binary solution containing 1 mol dm⁻³ LiPF₆ is higher than 80%. The EC-DFDMC solution is a good electrolyte for rechargeable lithium batteries.     

A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells

A green BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) electrolyte layer was deposited on porous anode substrate (BZCY:NiO = 35:65, in weight ratio) by a suspension spray. In this process, the suspension was prepared by directly ball-milling the mixed BaCO₃, CeO₂, ZrO₂ and Y₂O₃ powders in ethanol for 24 h. Then the bi-layers were co-sintered at 1400 °C for 5 h in air to obtain dense and uniform electrolyte membrane in the thickness of 10 μm. With Nd_0.7Sr_0.3MnO_3−δ cathode, a fuel cell was assembled. It was tested from 600 °C to 700 °C using humid hydrogen as fuel and air as oxidant. The cell at 700 °C exhibited 1.02 V for open circuit voltage (OCV), 450 mW/cm² for peak output and 0.18 Ω cm² for electrode polarizations under open circuit conditions, respectively. The results indicate that it is feasible to fabricate thin electrolyte membrane for solid oxide fuel cells (SOFCs) by this simple, cost-effective and efficient technique.     

Determination of sinomenine in Sinomenium acutum by capillary electrophoresis with electrochemiluminescence detection

A Ru(bpy)₃²⁺-based electrochemiluminescence (ECL) detection coupled with capillary electrophoresis (CE) has been established for the determination of sinomenine for the first time. Optimum separation was achieved with a fused-silica capillary column (50 cm × 25 μm i.d.) and a background electrolyte of 50 mM sodium phosphate (pH 5.0) at a separation voltage of 15 kV. The content of sinomenine was detected by ECL at the detection voltage of 1.15 V (versus Ag/AgCl) with 5 mM Ru(bpy)₃²⁺ in 75 mM phosphate solution (pH 8.0) when a chemically modified platinum electrode by europium(III)-doped prussian blue analogue (Eu-PB) was used as a working electrode. Under the optimized conditions, the ECL intensity was in proportion to sinomenine concentration in the range from 0.01 to 1.0 μg mL⁻¹ with a detection limit of 2.0 ng mL⁻¹ (3σ). The relative standard derivations of migration time and ECL intensity were 0.93 and 1.11%, respectively. The level of sinomenine in Sinomenium acutum Rehd. et Wils was easily determined with recoveries between 98.6 and 102.7%.     

Characterization of a carbon paste electrode modified with tripolyphosphate-modified kaolinite clay for the detection of lead

We report about the use of carbon paste electrode modified with kaolinite for analytical detection of trace lead(II) in domestic water by differential pulse voltammetry. Kaolinite clay was modified with tripolyphosphate (TPP) by impregnation method. The results show that TPP in kaolinite clay plays an important role in the accumulation process of Pb(II) on the modified electrode surface. The electroanalytical procedure for determination of Pb(II) comprised two steps: chemical accumulation of the analyte under open-circuit conditions, followed by electrochemical detection of the pre-concentrated species using differential pulse voltammetry. The analytical performance of this system has been explored by studying the effects of preconcentration time, carbon paste composition, pH, supporting electrolyte concentration, as well as interferences due to other ions. The calculated detection limit based on the variability of a blank solution (3s_b criterion) for 10 measurements was 8.4 × 10⁻⁸ mol L⁻¹, and the sensitivity determined from the slope of the calibration graph was 0.910 mol L⁻¹. The reproducibility (RSD) for five replicate measurements at 1.0 mg L⁻¹ lead level was 1.6%. The results indicate that this electrode is sensitive and effective for the determination of Pb²⁺.     

Aqueous-organic biphasic redox-chemistry of high-hydride content rhodium clusters: Towards immobilisation of redox-switchable H2 binding materials on a surface

Water-insoluble phosphine-surface-stabilised rhodium clusters (R = cyclohexyl, Ar^F = (3,5-CF₃)₂C₆H₃) can be immobilised onto suitable glassy carbon, graphite, or tin-doped indium oxide (ITO) electrode surfaces. When immersed into alcohol/aqueous electrolyte media, they display stable voltammetric responses consistent with the formation of organic microdroplet | aqueous electrolyte two-phase conditions which are similar to those observed in corresponding anhydrous (CH₂Cl₂) solution phase. This results in an electrode surface that is straightforwardly modified with cluster materials that can uptake or release dihydrogen depending on their redox-state. The results presented herein lead to a slight re-evaluation of the originally reported hydrogen store and release cycle for this system.     

Elektrochemische Methode zur quantitativen und kontinuierlichen Bestimmung von Ozon in Gasgemischen

The method is based on the measurement of the diffusion controlled limiting current obtained with the cathodic reduction of ozone according to O₃ + 2H⁺ + 2e^? → H₂O + O₂ in sulphuric acid. The electrolyte is vigorously mixed with the gas containing ozone and circulated through the electrolytic cell by the ascending gas flow operating as a gas-lift pump. The solution saturated with ozone moves along a cylindric electrode consisting of a smooth platinum foil in laminar flow. A constant potential is maintained at the electrode by means of a potentiostat in such a way, that the electrochemical reaction is proceeding under limiting current conditions. A lead anode of high capacitiy is used as a counter- and reference electrode. The current recorded continuously is directly proportional to the concentration of ozone in gas.     

Electrochemical behavior of dopamine at a 3,3′-dithiodipropionic acid self-assembled monolayers

Monolayers of 3,3′-dithiodipropionic acid (DTDPA) were prepared on a polycrystalline gold electrode through a self-assembly procedure to produce a gold 3,3′-dithiodipropionic acid self-assembled monolayer (AuDTDPA) modified electrode. The characterization of the AuDTDPA electrode was investigated by cyclic voltammetry and ac impedance using the [Fe(CN)₆]^3−/4− redox couple. The electrochemical behavior of DA on the modified electrode AuDTDPA was studied by cyclic and square-wave voltammetries, using phosphate buffer as supporting electrolyte. The oxidation peak current for DA increases linearly with concentration in the range of 0.35 × 10⁻⁵ to 3.4 × 10⁻⁵ mol L⁻¹. The performance of the AuDTDPA modified electrode was evaluated for the electroanalytical determination of dopamine (DA) in a pharmaceutical formulation. The AuDTDPA modified electrode showed a stable behavior and the presence of surface-COOH groups avoided the passivation of the electrode surface during the dopamine oxidation.     

Determination of As(III) and arsenic(V) in natural waters by cathodic stripping voltammetry at a hanging mercury drop electrode

A simple, fast and quantitative method was developed for the determination of As(III) and total inorganic arsenic (As (total)) in natural spring and mineral waters using square wave cathodic stripping voltammetry (SWCSV) at a hanging mercury drop electrode (HMDE). In the determination of As(III), pre-concentration was carried out on the electrode from a solution of 1 mol/l HCl in the presence of 45 ppm of Cu(II) at a potential of −0.39 V versus Ag/AgCl, and the deposited intermetallic compound was reduced at a potential of about −0.82 V versus Ag/AgCl. In the determination of As (total) the pre-concentration was carried out in 1 mol/l HCl in the presence of 400 ppm of Cu(II) at a potential of −0.40 V versus Ag/AgCl, and the intermetallic compound deposited was reduced at a potential of about −0.76 V versus Ag/AgCl. For determination of As(III) the quantification limit was 0.2 ppb for a deposition time of 40 s, and the relative standard deviation (R.S.D.) was calculated to be 6% (n=13) for a solution with 8 ppb of As(III). For As (total), the quantification limit was 2 ppb for a deposition time of 3 min, and the R.S.D. was calculated to be 3% (n=10) for a solution with 8 ppb of As(V). The method was validated by application of recovery and duplicate tests in the measurements of As(III) and As (total) in natural spring and mineral waters. For As (total), the results of the SWCSV method were compared with the results obtained by optical emission spectrometry with ICP coupled to hydride generation (OES-ICP-HG) good correlation being observed.     

A novel method for determination of magnesium in urine and water samples with mercury film-plated carbon paste electrode

A square wave adsorptive stripping voltammetric (SWAdSV) method for the indirect determination of trace amounts of magnesium with thiopentone sodium (TPS) as an electroactive ligand, at carbon paste mercury film electrode (CP-MFE) is proposed. It is observed that the increase of the square wave voltammetric cathodic peak current of TPS, under alkaline conditions, is linear with the increase of Mg concentration. Under optimum experimental conditions viz.; pH 10.75, 3×10⁻⁵ M TPS and 0.05 M phosphate buffer (Na₂HPO₄-NaH₂PO₄), a linear relation in the range 6×10⁻⁹ to 9×10⁻⁸ M Mg²⁺ (0.14-2.16 ppb), at 60 s deposition time, is obtained. The detection limit of Mg²⁺ is 0.14 ppb for 60 s deposition time with the relative standard deviation is 0.5% (n=5). The proposed method was successfully applied to the determination of magnesium in urine and tap water samples with satisfactory results. The data obtained are compared with the standard flame atomic absorption spectrophotometric method (FAAS).     

Hg(II) immobilized MWCNT graphite electrode for the anodic stripping voltammetric determination of lead and cadmium

The preparation of Hg(II)-modified multi walled carbon nanotube (MWCNT) by reaction of oxidized MWCNT with aqueous HgCl₂ was carried out. The Hg(II)-modified multi walled carbon nanotube (Hg(II)/MWCNT) dispersed in Nafion solution was used to coat the polished graphite electrode surface. The Hg(II)/MWCNT modified graphite electrode was held at a cathodic potential (−1.0 V) to reduce the coordinated Hg(II) to Hg forming nanodroplets of Hg. The modified electrode was characterized by FESEM/EDAX which provided useful insights on the morphology of the electrode. The SEM images showed droplets of Hg in the size of around 260 nm uniformly distributed on the MWCNT. Differential pulse anodic stripping voltammetry (DPASV) and electrochemical impedance spectroscopy were used to study the Hg(II) binding with MWCNT. Differential pulse anodic stripping voltammetry of ppb levels of cadmium and lead using the modified electrode yielded well-defined peaks with low background current under a short deposition time. Detection limit of 0.94 and 1.8 ng L⁻¹ were obtained following a 3 min deposition for Pb(II) and Cd(II), respectively. Various experimental parameters were characterized and optimized. High reproducibility was observed from the RSD values for 20 repetitive measurements of Pb(II) and Cd(II) (1.7 and 1.9%, respectively). The determination of Pb(II) and Cd(II) in tap water and Pb(II) in human hair samples was carried out. The above method of fabrication of Hg(II)/MWCNT modified graphite electrode clearly suggests a safe route for preparing Hg immobilized electrode for stripping analysis.     

Amperometric biosensing of carbamate and organophosphate pesticides utilizing screen-printed tyrosinase-modified electrodes

A tyrosinase (Tyr) screen-printed biosensor based on the electroreduction of enzymatically generated quinoid products was electrochemically characterized and optimized for determination of carbamates and organophosphorus pesticides. A composite electrode prepared by screen-printing a cobalt (II) phthalocyanine (CoPc) modified cellulose-graphite composite on a polycarbonate support was employed as electrochemical transducer. The Tyr biosensor was prepared by immobilization of enzyme on the composite electrode surface by cross-linking with glutaraldehyde and bovine serum albumin. Parameters affecting the biosensor response such as response time, enzyme loading, concentration and pH of the buffer solution were optimized utilizing catechol as substrate. The maximum response for o-quinone enzymatically generated was obtained after 2 min of reaction. A good reproducibility and high operational stability were found for Tyr biosensor (60 units) at 50 mM phosphate buffer, pH 6.50. Under these conditions, the useful lifetime of biosensor was 10 days. After 15 days, the biosensor could be used with 20% of the initial value. Inhibition studies on the o-quinone steady-state current (at −0.20 V versus Ag/AgCl) were performed to investigate the inhibition kinetics of the pesticides in the enzymatic activity of mushroom tyrosinase. The results shown that the methyl parathion and carbofuran can lead to competitive inhibition process of the enzyme, while diazinon and carbaryl act as mixed inhibitors. Linear relationships were found for methyl parathion (6-100 ppb), diazinon (19-50 ppb), carbofuran (5-90 ppb) and carbaryl (10-50 ppb). Analysis of natural river water samples spiked with 30 ppb of each pesticide showed recoveries between 92.50% and 98.50% and relative standard deviations of 2%.     

Amperometric quantification of sodium metabisulfite in pharmaceutical formulations utilizing tetraruthenated porphyrin film modified electrodes and batch injection analysis

The performance of a glassy carbon electrode modified with a porphyrin film formed by the [Co(TPyP){Ru(bipy)₂Cl}₄](TFMS)₅·H₂O complex for the analysis of sodium metabisulfite in pharmaceuticals is described. The sensor can be rapidly and easily prepared by drop-casting of a microliter volume of a diluted methanolic solution of the complex onto the electrode surface. The modified electrode with a supramolecular cobalt porphyrin film led to more favorable responses than the bare electrode. This can be ascribed to the much faster electron transfer processes to the analyte mediated by the tetraruthenated porphyrin and to the protection of the electrode against fouling. The association of the amperometric sensor with the batch injection analysis technique led to results that combine good repeatability of the current responses (relative standard deviation of 0.94% for 30 measurements), wide linear dynamic range (2.5 × 10⁻⁷ mol L⁻¹ to 5.0 × 10⁻⁴ mol L⁻¹), high sensitivity and low limits of detection (8.1 × 10⁻⁸ mol L⁻¹) and quantification (2.7 × 10⁻⁷ mol L⁻¹). The system was successfully applied to sodium metabisulfite quantification in commercial samples of injection formulations of sodium (or potassium) diclofenac. The results compared well with those obtained by the polarographic method.     

The petentiometric determination of peroxide hydrogen and glucose on the glassy electrode modified by the calix[4]arene

A new petentiometric method to determine peroxide hydrogen and glucose had been studied. This method had been applied on the petentiometric determination of peroxide hydrogen and glucose in the total ionic strength adjustment buffer (TISAB) (pH 7.5) solution with the glassy electrode modified by the calix[4]arene. The glassy carbon electrode covered with the calix[4]arene depended on the H₂O₂ concentration in the range of log[H₂O₂] from −3.3 to −1.2 in the solution of TISAB (pH 7.5) with nearly Nernstian slope of about 65.6 ± 3 mV and the detection limit of peroxide hydrogen was 4.0 × 10⁻⁵ mol L⁻¹. The glassy carbon electrode covered with the calix[4]arene depended on the glucose concentration in the range of log[glucose] from −3.6 to −2.8 in the solution of TISAB (pH 7.5) with nearly Nernstian slope of about 50.2 ± 2 mV and the detection limit of glucose was 2.0 × 10⁻⁵ mol L⁻¹. The electrode had the good selectivity, sensitivity, stability and repeatability.     

Preparation and characterization of Prussian blue nanowire array and bioapplication for glucose biosensing

Prussian blue nanowire array (PBNWA) was prepared via electrochemical deposition with polycarbonate membrane template for effective modification of glassy carbon electrode. The PBNWA electrode thus obtained was demonstrated to have high-catalytic activity for the electrochemical reduction of hydrogen peroxide in neutral media. This enabled the PBNWA electrode to show rapid response to H₂O₂ at a low potential of −0.1 V over a wide range of concentrations from 1 × 10⁻⁷ M to 5 × 10⁻² M with a high sensitivity of 183 μA mM⁻¹ cm⁻². Such a low-working potential also substantially improved the selectivity of the PBNWA electrode against most electroactive species such as ascorbic acid and uric acid in physiological media. A detection limit of 5 × 10⁻⁸ M was obtained using the PBNWA electrode for H₂O₂, which compared favorably with most electroanalysis procedures for H₂O₂. A biosensor toward glucose was then constructed with the PBNWA electrode as the basic electrode by crosslinking glucose oxidase (GOx). The glucose biosensor allowed rapid, selective and sensitive determination of glucose at −0.1 V. The amperometric response exhibited a linear correlation to glucose concentration through an expanded range from 2 × 10⁻⁶ M to 1 × 10⁻² M, and the response time and detection limit were determined to be 3 s and 1 μM, respectively.