Determination of l-histidine by modified carbon paste electrode using tetra-3,4-pyridinoporphirazinatocopper(II)

This paper describes a potentiometric method for determination of l-histidine (l-his) in aqueous media, using a carbon paste electrode modified with tetra-3,4-pyridinoporphirazinatocopper(II) (Cu (3,4tppa)). The electrode exhibits linear response to the logarithm of the concentration of l-histidine from 2.4 × 10⁻⁵ to 1.0 × 10⁻² M, with a response slope of −49.5 ± 1 mV and response time of about 1.5 min. The detection limit according to IUPAC recommendation was 2.0 × 10⁻⁵ M. The proposed electrode shows a good selectivity for l-his over a wide variety of anions. This chemically modified carbon paste electrode was successfully used for the determination of l-his in a synthetic serum and RANDOX control serum solutions.     

Study of the electrochemical behavior of isorhamnetin on a glassy carbon electrode and its application

The electrochemical behavior of isorhamnetin (ISO) at a glassy carbon electrode was studied in a phosphate buffer solution (PBS) of pH 4.0 by cyclic voltammetry (CV) and differential pulse voltammetric method (DPV). A well-defined redox wave of ISO involving one electrons and one proton appeared. The electrode reaction is a reactant weak adsorption-controlled process with a charge transfer coefficient (α) of 0.586. Based on the understanding of the electrochemical process of ISO at the glassy carbon electrode, analysis of ISO can be realized. Under optimal conditions, the oxidation peak current showed linear dependence on the concentration of ISO in the range of 1.0 × 10⁻⁸ to 4.0 × 10⁻⁷ M and 1.0 × 10⁻⁶ to 1.0 × 10⁻⁵ M. The detection limit is 5.0 × 10⁻⁹ M. This method has been successfully applied to the detection of ISO in tablets.     

Gold nanoparticles modified indium tin oxide electrode for the simultaneous determination of dopamine and serotonin: Application in pharmaceutical formulations and biological fluids

A new rapid, convenient and sensitive electrochemical method based on a gold nanoparticles modified ITO (Au/ITO) electrode is described for the detection of dopamine and serotonin in the presence of a high concentration of ascorbic acid. The electrocatalytic response was evaluated by differential pulse voltammetry (DPV) and the modified electrode exhibited good electrocatalytic properties towards dopamine and serotonin oxidation with a peak potential of 70 mV and 240 mV lower than that at the bare ITO electrode, respectively. The selective sensing of dopamine is further improved by applying square wave voltammetry (SWV) which leads to the lowering of its detection limit. A similar effect on the detection limit of serotonin was observed on using SWV. Linear calibration curves are obtained in the range 1.0 × 10⁻⁹-5.0 × 10⁻⁴ M and 1.0 × 10⁻⁸-2.5 × 10⁻⁴ M with a detection limit of 0.5 nM and 3.0 nM for dopamine and serotonin, respectively. The Au/ITO electrode efficiently determines both the biomolecules simultaneously, even in the presence of a large excess of ascorbic acid. The adequacy of the developed method was evaluated by applying it to the determination of the content of dopamine in dopamine hydrochloride injections. The proposed procedure was also successfully applied to simultaneously detect dopamine and serotonin in human serum and urine.     

Use of organofunctionalized nanoporous silica gel to improve the lifetime of carbon paste electrode for determination of copper(II) ions

A new functionalized nanoporous silica gel with dipyridyl group (DPNSG) was synthesized. Then, the potentiometric response of the copper(II) ion was investigated at a carbon paste electrode chemically modified with this newly designed functionalized nanoporous silica gel. The electrodes with DPNSG proportions of 15.0% (w/w) demonstrated very stable potentials. Calibration plots with Nernstian slopes for Cu²⁺ were observed, 28.4 (±1.0) mV decade⁻¹, over a wide linear concentration range (1.0 × 10⁻⁷ to 1.0 × 10⁻² M). The electrode exhibited a detection limit of 8.0 × 10⁻⁸ M. Moreover, the selectivity coefficients measured by the match potential method in acetate buffer, pH 5.5, were investigated. The electrode presented a response time of ∼50 s, high performance, high sensitivity in a wide range of cation activities and good long-term stability (more than 9 months). The method was satisfactory and was used to determine the copper ion concentration in waste waters, contaminated by this metal.     

Highly selective thiocyanate membrane electrode based on butane-2,3-dione bis(salicylhydrazonato)zinc(II) complex

A highly selective poly(vinyl chloride) (PVC) membrane electrode based on butane -2,3-dione bis(salicylhydrazonato) zinc(II) [Zn (BDSH)] complex as carrier for thiocyanate-selective electrode is reported. The influence of membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. The sensor responds to thiocyanate in linear range from 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a slope −56.5 ± 1.1 mV decade⁻¹, over a wide pH range of 3.5-8.5. The limit of detection of the electrode was 7.0 × 10⁻⁷ M SCN⁻. Selectivity coefficients determined with fixed interference method (FIM) indicate a good discriminating ability towards SCN⁻ ion in comparison to other anions. The proposed sensor has a fast response time of about 5-15 s and can be used for at least 3 months without any considerable divergence in potential. It was applied as indicator electrode in titration of thiocyanate with Ag⁺ and in potentiometric determination of thiocyanate in saliva and urine samples.     

Dodecyl benzene sulfonate anion-selective electrode based on polyaniline-coated electrode

A new dodecyl benzene sulfonate (DBS⁻) ion-selective electrode based on polyaniline is reported. The films of polyaniline doped with DBS⁻ were prepared electrochemically on platinum electrodes in the solution containing 1.0×10⁻³ M aniline and 7.0×10⁻³ M DBS⁻. The optimum potentiometric response was obtained for prepared polymeric film by passing electricity of 7.5 C cm⁻². The electrode exhibits an excellent Nernstian slope of −59.1±0.3 mV per decade for DBS⁻ ion over a wide concentration range (5.0×10⁻⁶ to 4.1×10⁻³ M) with a low detection limit (1.0×10⁻⁶ M). The proposed electrode revealed good sensitivities for DBS⁻ ion over a wide variety of other anions and can be used in the wide pH range of 5-10. It shows good stability, good reproducibility, wide range of pH independency and fast response (<20 s) without using internal solution. This electrode could be used for the determination of DBS⁻ in the real samples.     

Highly selective and sensitive thiocyanate membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine

A highly selective membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine (NOBP) is presented. The proposed electrode shows very good selectivity for thiocyanate ions over a wide variety of common inorganic and organic anions. The sensor displays a near Nernstian slope of −58.7 ± 0.6 mV per decade. The working concentration range of the electrode is 1.0 × 10⁻⁶ to −1.0 × 10⁻¹ M with a detection limit of 5.7 × 10⁻⁷ M (33.06 ng/mL). The response time of the sensor in whole concentration ranges is very short (<10 s). The response of the sensor is independent on the pH range of 4.3-9.8. The best performance was obtained with a membrane composition of 30% PVC, 65% dibutyl phthalate, 3% NOBP and 2% hexadecyltrimethylammonium bromide. It was successfully applied to direct determination of thiocyanate in biological samples, and as an indicator electrode for titration of thiocyanate ions with AgNO₃ solution.     

A selective modified carbon paste electrode for determination of cyanide using tetra-3,4-pyridinoporphyrazinatocobalt(II)

A chemically modified carbon paste electrode with 3,4-tetra pyridinoporphirazinatocobalt(II) (Co(3,4 tppa) was applied to the determination of free cyanide ion. The electrode has a linear range between 1.5 × 10⁻⁵ M and 1.0 × 10⁻² M with a Nernstian slope of 60 ± 1.5 mV/decade and its detection limit is 9 × 10⁻⁶ M. The response time of electrode is 5 min. The proposed electrode was applied successfully for the determination of cyanide in commercially available spring water. Some anions, such as SCN⁻, I⁻, Cl⁻, Br⁻ and oxalate that are usually serious interfering species for most of cyanide selective electrodes, did not have any interfering effect for this proposed electrode.     

An electrochemiluminescent biosensor for glucose based on the electrochemiluminescence of luminol on the nafion/glucose oxidase/poly(nickel(II)tetrasulfophthalocyanine)/multi-walled carbon nanotubes modified electrode

A poly(nickel(II) tetrasulfophthalocyanine)/multi-walled carbon nanotubes composite modified electrode (polyNiTSPc/MWNTs) was fabricated by electropolymerization of NiTSPc on MWNTs-modified glassy carbon electrode (GCE). The modified electrode was found to be able to greatly improve the emission of luminol electrochemiluminescence (ECL) in a solution containing hydrogen peroxide. Glucose oxidase (GOD) was immobilized on the surface of polyNiTSPc/MWNTs modified GC electrode by Nafion to establish an ECL glucose sensor. Under the optimum conditions, the linear response range of glucose was 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 8.0 × 10⁻⁸ mol L⁻¹ (defined as the concentration that could be detected at the signal-to-noise ratio of 3). The ECL sensor showed an outstanding well reproducibility and long-term stability. The established method has been applied to determine the glucose concentrations in real serum samples with satisfactory results.     

Molecularly imprinted polymer based potentiometric sensor for the determination of hydroxyzine in tablets and biological fluids

Molecular imprinting is a useful technique for the preparation of functional materials with molecular recognition properties. In this work, a biomimetic potentiometric sensor, based on a non-covalent imprinted polymer, was fabricated for the recognition and determination of hydroxyzine in tablets and biological fluids. The molecularly imprinted polymer (MIP) was synthesized by precipitation polymerization, using hydroxyzine dihydrochloride as a template molecule, methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylat (EGDMA) as a cross-linking agent. The sensor showed a high selectivity and a sensitive response to the template in aqueous system. The MIP-modified electrode exhibited a Nernstian response (29.4 ± 1.0 mV decade⁻¹) in a wide concentration range of 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a lower detection limit of 7.0 × 10⁻⁷ M. The electrode demonstrated a response time of ∼15 s, a high performance and a satisfactory long-term stability (more than 5 months). The method has the requisite accuracy, sensitivity and precision to assay hydroxyzine in tablets and biological fluids.     

Organically nanoporous silica gel based on carbon paste electrode for potentiometric detection of trace Cr(III)

A new ion-selective electrode (ISE) for the detection of trace chromium(III) was designed by using 2-acetylpyridine and nanoporous silica gel (APNSG)-functionalized carbon paste electrode (CPE). The presence of APNSG acted as not only a paste binder, but also a reactive material. With 7.5 wt% APNSG proportions, the developed electrode exhibited wide dynamic range of 1.0 × 10⁻⁸ to 1.0 × 10⁻³ M toward Cr(III) with a detection limit of 8.0 × 10⁻⁹ M and a Nernstian slope of 19.8 ± 0.2 mV decade⁻¹. The as-prepared electrode displayed rapid response (∼55 s), long-time stability, and high sensitivity. Moreover, the potentiometric responses could be carried out with wide pH range of 1.5-5.0. In addition, the content of Cr(III) in food samples, e.g. coffee and tea leaves, has been assayed by the developed electrode, atomic absorption spectrophotometer (AAS) and atomic emission spectrometer (ICP-AES), respectively, and consistent results were obtained. Importantly, the response mechanism of the proposed electrode was investigated by using AC impedance and UV-vis spectroscopy.     

Carbon paste electrode modified with silver thimerosal for the potentiometric flow injection analysis of silver(I)

The utility of carbon paste electrode modified with silver ethylmercurythiosalicylate (silver thimerosal) in both static mode and flow injection analysis (FIA) is demonstrated. The electrode was fully characterized in terms of composition, response time, thermal stability, usable pH and ionic strength ranges. It has been shown that diisononyl phthalate (DINP) acts as more suitable solvent mediator for preparation of the electrode, which exhibits linear response range to Ag(I) extending from 5.0 × 10⁻⁷ to 1.0 × 10⁻³ M with detection limit of 2.5 × 10⁻⁷ M and Nernstian slope of 59.3 ± 1.0 mV/decade. The proposed chemically modified carbon paste electrode shows a very good selectivity for Ag(I) over a wide variety of metal ions and successfully used for the determination of the silver content of silver sulphadiazine (burning cream) and developed radiological films. The electrode was also used as an indicator electrode in the potentiometric titration of thiopental and thimerosal with AgNO₃.     

Sensitive voltammetric determination of baicalein at DNA Langmuir-Blodgett film modified glassy carbon electrode

The present paper describes to modify a double stranded DNA-octadecylamine (ODA) Langmuir-Blodgett film on a glassy carbon electrode (GCE) surface to develop a voltammetric sensor for the detection of trace amounts of baicalein. The electrode was characterized by atomic force microscopy (AFM) and cyclic voltammetry (CV). Electrochemical behaviour of baicalein at the modified electrode had been investigated in pH 2.87 Britton-Robinson buffer solutions by CV and square wave voltammetry (SWV). Compared with bare GCE, the electrode presented an electrocatalytic redox for baicalein. Under the optimum conditions, the modified electrode showed a linear voltammetric response for the baicalein within a concentration range of 1.0 × 10⁻⁸-2.0 × 10⁻⁶ mol L⁻¹, and a value of 6.0 × 10⁻⁹ mol L⁻¹ was calculated for the detection limit. And the modified electrode exhibited an excellent immunity from epinephrine, dopamine, glucose and ascorbic acid interference. The method was also applied successfully to detect baicalein in the medicinal tablets and spiked human blood serum samples with satisfactory results.     

Improved potentiometric response of solid-contact lanthanum (III) selective electrode

For the first time, the analytical application of integrate ionophore-transducer material based on magnetic graphene hybrids and 2,2-dithiodipyridine (DTDP) in solid-contact lanthanum (III) selective electrode is reported. The attachment of Fe₃O₄ nanoparticles (NPs) to graphene oxide (GO) for magnetic graphene hybrid is achieved by covalent bonding, and the universal problem, Fe₃O₄ NPs may easily leach out from the graphene during application, is successfully solved by the method above. The proposed electrode exhibits an excellent near-Nernstian response to lanthanum (III) ranging from 1.0 × 10⁻⁹ to 1.0 × 10⁻³ M with a slope of 17.81 mV/dec. Moreover, the excellent performance on fairly good selectivity, wide applicable pH range (3.0^_8.0), fast response time (10 s) and long life time (2 months) reveal the superiority of the electrode. Most importantly, we have made a great improvement in the detection limit (2.75 × 10⁻¹⁰ M), which brings new dawn to the real-time detection of lanthanum (III) using ion selective electrode.     

Development of prototype heterogeneous chitosan membrane using different plasticizer for glutamate sensing

This paper describes the preparation of and experimentation undertaken by heterogeneous chitosan membrane as ion selective electrode for glutamate ion. The linearity response was obtained in the range of 1.0 × 10⁻⁵ to 1.0 × 10⁻¹ M with a detection limit of 1.0 × 10⁻⁶ M. The performance of the electrode was found in the pH range of 4.0-8.0 at temperature 25 ± 3 °C. The response time was at 5-35 s and was useful for a period of more than 4 months. The selectivity values towards some anions indicates good selectivity over a number of interfering anions. No significant improvement of membrane performance over additional of plasticizers such as 2-NPOE, BEHA and DOPP. The electrodes gave sufficient Nernstian responses with the exception of membrane with 2-NPOE.     

Flow-injection fluorometric quantification of pyruvate using co-immobilized pyruvate decarboxylase and aldehyde dehydrogenase reactor: Application to measurement of acetate, citrate and l-lactate

A flow-injection system for the quantification of pyruvate based on the coupled reactions of pyruvate decarboxylase (PDC) and aldehyde dehydrogenase (AlDH) was conceived and optimized. A co-immobilized PDC and AlDH reactor was introduced into the flow line. Sample and reagent (NAD⁺) were injected into the flow line by an open sandwich method and the increase of NADH produced by the immobilized-enzyme reactor was monitored fluorometrically at 455 nm (excitation at 340 nm). Linear relationships between the responses and concentrations of pyruvate were observed in the ranges of 2.0 × 10⁻⁵ to 1.5 × 10⁻³ M at the flow rate of 1.0 ml min⁻¹ and 5.0 × 10⁻⁶ to 1.0 × 10⁻³ M at the flow rate of 0.5 ml min⁻¹. The relative standard deviation for 10 successive injections was 0.95% at the 1.0 mM level. This FIA system for pyruvate was applied to the measurement of acetate, citrate and l-lactate.     

Ultrasensitive photoelectrochemical sensing of nicotinamide adenine dinucleotide based on graphene-TiO2 nanohybrids under visible irradiation

In this paper, the photoelectrochemical behavior of graphene-TiO₂ (G-TiO₂) nanohybrids was investigated in the visible region and a new photoelectrochemical sensor for sensitive determination of nicotinamide adenine dinucleotide (NADH) was proposed. Under visible light, the G-TiO₂ nanohybrids possessed enhanced photocurrent, which was nearly 5 times than that of pure TiO₂ nanocrystals (NCs). Based on the enhanced photocurrent of G-TiO₂ nanohybrids toward NADH, a new photoelectrochemical methodology for ultrasensitive determination of NADH was developed. The proposed sensor showed linearly enhanced photocurrent by increasing the NADH concentration from 1.0 × 10⁻⁸ to 2.0 × 10⁻³ M with a low detection limit of 3.0 × 10⁻⁹ M. Furthermore, this sensor exhibited good selectivity and stability towards NADH determination. This strategy opens up a new avenue for the application of graphene-based hybrids in the field of photoelectrochemical sensing and monitoring.     

Electrochemically monitoring the binding of concanavalin A and ovalbumin

To evaluate protein-protein interactions, a new voltammetric method was developed using a protein labeled with an electroactive compound. Concanavalin A (ConA), which is a lectin, recognizes α-mannose residues. Because the ConA was to be bound to ovalbumin (OVA), which has a high-mannose sugar chain, ConA labeled with daunomycin was prepared as the probe to monitor the binding. The binding to OVA was caused by the label modification of the ConA. As a result, the electrode response of the labeled ConA decreased as the OVA concentration increased. The electrode response of the labeled ConA was linearly over the range of 1.5 × 10⁻¹⁰ and 1.5 × 10⁻⁹ M OVA. The relative standard deviation of 1.5 × 10⁻⁸ M labeled ConA and 1.5 × 10⁻¹⁰ M OVA was 6.9% (n = 5). The labeled ConA-OVA binding could then be conveniently monitored based on the change in response. In contrast, interactions between the labeled ConA and a protein with no specific sugar chain also were investigated. Incubation scarcely influenced the peak current of the labeled ConA. When several concentrations of OVA were added to a serum, good recovery determined it. Consequently, this method could be applied to the measurement of protein-protein interactions.     

Application of cement as new electrode material and solid-phase microextraction material demonstrated by electrochemiluminescent detection of perphenazine

Because of its unique pore network, good strength, and low cost, cement was used as a new electrode material and solid-phase microextraction (SPME) material for the first time. It was mixed with carbon to make a new electrode, cement carbon electrode (CCE). The as-prepared CCE was used to demonstrate the application of cement in SPME by Ru(bpy)₃²⁺ electrochemiluminescent detection of perphenazine (PPZ). The calibration plot for PPZ is linear from 1.0 × 10⁻⁹ to 3.0 × 10⁻⁶ M with a detection limit of 3.1 × 10⁻¹⁰ M. The method was successfully applied to the detection of PPZ in urine sample. Cement-based electrode material may also find broad applications in electrochemistry industry, such as electrochemical wastewater treatment.     

Solid-contact potentiometric sensor for ascorbic acid based on cobalt phthalocyanine nanoparticles as ionophore

A novel solid-contact potentiometric sensor for ascorbic acid based on cobalt phthalocyanine nanoparticles (NanoCoPc) as ionophore was fabricated without any need of auxiliary materials (such as membrane matrix, plasticizer, and other additives). The electrode was prepared by simple drop-coating NanoCoPc colloid on the surface of a glassy carbon electrode. A smooth, bright and blue thin film was strongly attached on the surface of the glassy carbon electrode. The electrode showed high selectivity for ascorbic acid, as compared with many common anions. The influences of the amount of NanoCoPc at the electrode surface and pH on the response characteristics of the electrode were investigated. To overcome the instability of the formal potential of the coated wire electrode, a novel electrochemical pretreatment method was proposed for the potentiometric sensor based on redox mechanism. This resulting sensor demonstrates potentiometric response over a wide linear range of ascorbic acid concentration (5.5 × 10⁻⁷ to 5.5 × 10⁻² M) with a fast response (<15 s), lower detection limit (ca. 1.0 × 10⁻⁷ M), and a long-term stability. Furthermore, microsensors based on different conductors (carbon fiber and Cu wire) were also successfully fabricated for the determination of practical samples.