Simultaneous spectrophotometric determination of ethinylestradiol and levonorgestrel by partial least squares and principal component regression multivariate calibration

Two spectrophotometric methods for the determination of Ethinylestradiol (ETE) and Levonorgestrel (LEV) by using the multivariate calibration technique of partial least square (PLS) and principal component regression (PCR) are presented. In this study the PLS and PCR are successfully applied to quantify both hormones using the information contained in the absorption spectra of appropriate solutions. In order to do this, a calibration set of standard samples composed of different mixtures of both compounds has been designed. The results found by application of the PLS and PCR methods to the simultaneous determination of mixtures, containing 4–11 μg ml⁻¹ of ETE and 2–23 μg ml⁻¹ of LEV, are reported. Five different oral contraceptives were analyzed and the results were very similar to that obtained by a reference liquid Chromatographic method.     

多模型共识偏最小二乘法用于近红外光谱定量分析

将多模型共识偏最小二乘法用于近红外光谱定量分析。利用随机抽取的训练子集建立一系列偏最小二乘模型,选取其中性能较好的部分模型作为成员模型,用这些成员模型来预测未知样品。将该方法用于一组生物样本的近红外光谱与样品中人血清白蛋白、γ-球蛋白以及葡萄糖含量之间的建模研究,并与单模型偏最小二乘法了进行比较。结果 PLS对独立测试集中三种组分进行50次重复预测的平均RMSEP分别为0.1066,0.0853和0.1338,RMSEP的标准偏差分别为0.0174,0.0144和0.0416;而本方法重复预测的平均RMSEP分别为0.0715,0.0750和0.0781,RMSEP的标准偏差分别为0.0033,0.2729×10-4和0.0025。     

Optimization of transmission near infrared spectrometry procedures for quality control of pesticide formulations

The use of different response functions to be optimized in the frame of the use of near infrared spectrometry for quality control of active principles in agrochemical formulations has been evaluated. Both, simple functions, based on parameters like sensitivity, repeatability, accuracy, signal to noise ratio, limit of detection or sample throughput, and a complex function, considering all the aforementioned aspects, were employed in the development of a new method for Iprodione determination in agrochemicals. Optimization strategies were based on the previous screening of the most important instrumental factors like number of cumulated scans, nominal resolution, mirror velocity and zero filling factor, based on a two-level full factorial design and on the search for the optimum conditions using central composite designs. Data found evidenced the influence of the response function on the optimum values of experimental conditions and could be employed as a general guide to evaluate the experimental factors in routine use of near infrared spectrometry. Finally the optimized method for Iprodione has been applied to the determination of Diuron and results found compared with those obtained by a conventional approach.     

偏最小二乘近红外光谱法测定瘦肉脂肪酸组成的研究

利用偏最小二乘将瘦肉的近红外光谱数据分别与其棕榈酸、棕榈油酸、硬脂酸、油酸、亚油酸含量建立校正模型,并用交互校验和外部检验来考查模型的可靠性.各脂肪酸模型的校正相关系数分别为0.9998、0.9844、0.9963、0.9754、0.9969,均方估计残差(RMSEC)分别为0.0231、0.0485、0.111、0.373、0.311,交互校验均方残差(RMSECV)分别为0.509、0.115、0.225、0.848、0.649.应用所建立的各脂肪酸近红外模型对瘦肉脂肪酸组成进行预测,并对各脂肪酸的预测值与气相色谱法测定值进行配对t-检验,结果表明两者差异均不显著(p>0.05).     

Maize kernel hardness classification by near infrared (NIR) hyperspectral imaging and multivariate data analysis

The use of near infrared (NIR) hyperspectral imaging and hyperspectral image analysis for distinguishing between hard, intermediate and soft maize kernels from inbred lines was evaluated. NIR hyperspectral images of two sets (12 and 24 kernels) of whole maize kernels were acquired using a Spectral Dimensions MatrixNIR camera with a spectral range of 960-1662 nm and a sisuChema SWIR (short wave infrared) hyperspectral pushbroom imaging system with a spectral range of 1000-2498 nm. Exploratory principal component analysis (PCA) was used on absorbance images to remove background, bad pixels and shading. On the cleaned images, PCA could be used effectively to find histological classes including glassy (hard) and floury (soft) endosperm. PCA illustrated a distinct difference between glassy and floury endosperm along principal component (PC) three on the MatrixNIR and PC two on the sisuChema with two distinguishable clusters. Subsequently partial least squares discriminant analysis (PLS-DA) was applied to build a classification model. The PLS-DA model from the MatrixNIR image (12 kernels) resulted in root mean square error of prediction (RMSEP) value of 0.18. This was repeated on the MatrixNIR image of the 24 kernels which resulted in RMSEP of 0.18. The sisuChema image yielded RMSEP value of 0.29. The reproducible results obtained with the different data sets indicate that the method proposed in this paper has a real potential for future classification uses.     

Multivariate analysis of remote laser-induced breakdown spectroscopy spectra using partial least squares,principal component analysis,and related techniques

Quantitative analysis with laser-induced breakdown spectroscopy traditionally employs calibration curves that are complicated by chemical matrix effects. These chemical matrix effects influence the laser-induced breakdown spectroscopy plasma and the ratio of elemental composition to elemental emission line intensity. Consequently, laser-induced breakdown spectroscopy calibration typically requires a priori knowledge of the unknown, in order for a series of calibration standards similar to the unknown to be employed. In this paper, three new Multivariate Analysis techniques are employed to analyze the laser-induced breakdown spectroscopy spectra of 18 disparate igneous and highly-metamorphosed rock samples. Partial Least Squares analysis is used to generate a calibration model from which unknown samples can be analyzed. Principal Components Analysis and Soft Independent Modeling of Class Analogy are employed to generate a model and predict the rock type of the samples. These Multivariate Analysis techniques appear to exploit the matrix effects associated with the chemistries of these 18 samples.     

Discrimination of Scrophulariae Radix according to geographical origin and determination of active constituents by near infrared spectroscopy (NIRS)

The potential of near infrared reflectance spectroscopy (NIR) was investigated for its ability to non-destructively discriminate the geographic origins of Scrophularia spp., Andong, Uisung and China. Application of principal component analysis to NIR spectra leads to a clear separation of Andong sample from the others. Moreover, the contents of two neuroprotective constituents of Scrophularia spp., 8-O-(E-p-methoxycinnamoyl)-harpagide (HG), and E-p-methoxycinnamic acid (MCA), were determined by HPLC-DAD. Partial least squares (PLS) regression of NIR spectra combined with these analytical reference data yield the development of calibration models for the contents of the two constituents. The correlation coefficients of prediction models for HG and MCA were > 0.87. These outcomes indicated that the NIRS could be useful for the discrimination of Scrophularia spp.     

Regression models based on new local strategies for near infrared spectroscopic data

In this work, a comparative study of two novel algorithms to perform sample selection in local regression based on Partial Least Squares Regression (PLS) is presented. These methodologies were applied for Near Infrared Spectroscopy (NIRS) quantification of five major constituents in corn seeds and are compared and contrasted with global PLS calibrations. Validation results show a significant improvement in the prediction quality when local models implemented by the proposed algorithms are applied to large data bases.     

Testing of the Region of Murcia soils by near infrared diffuse reflectance spectroscopy and chemometrics

A partial least squares near infrared (PLS-NIR) method has been developed for the determination of several physicochemical parameters in soils from different locations of the Region of Murcia. The method was based on the proper chemometric treatment of diffuse reflectance spectra of soil samples. Reflectance spectra were scanned from samples stored in glass vials in the NIR region between 800 and 2600 nm, averaging 36 scans per spectrum at a resolution of 8 cm⁻¹. Models were built using reference data of 39 samples selected from a dendrogram obtained after hierarchical cluster analysis of NIR spectra of soils and prediction parameters were established from a validation set of 109 additional samples of the same area not considered to build the model. Organic matter, CaCO₃, pH, electrical conductivity (EC), together with several trace metals as Cr, Co, Ni, Cu, Zn, As, Se, Cd and Tl, were employed as characteristic parameters of the soils under study, and found results evidenced that PLS-NIR provides a valuable tool for screening purposes providing residual predictive deviations which ranged from 0.9 to 1.5 as a function of the considered parameter.     

Feasibility study on qualitative and quantitative analysis in tea by near infrared spectroscopy with multivariate calibration

This study attempted the feasibility to use near infrared (NIR) spectroscopy as a rapid analysis method to qualitative and quantitative assessment of the tea quality. NIR spectroscopy with soft independent modeling of class analogy (SIMCA) method was proposed to identify rapidly tea varieties in this paper. In the experiment, four tea varieties from Longjing, Biluochun, Qihong and Tieguanyin were studied. The better results were achieved following as: the identification rate equals to 90% only for Longjing in training set; 80% only for Biluochun in test set; while, the remaining equal to 100%. A partial least squares (PLS) algorithm is used to predict the content of caffeine and total polyphenols in tea. The models are calibrated by cross-validation and the best number of PLS factors was achieved according to the lowest root mean square error of cross-validation (RMSECV). The correlation coefficients and the root mean square error of prediction (RMSEP) in the test set were used as the evaluation parameters for the models as follows: R = 0.9688, RMSEP = 0.0836% for the caffeine; R = 0.9299, RMSEP = 1.1138% for total polyphenols. The overall results demonstrate that NIR spectroscopy with multivariate calibration could be successfully applied as a rapid method not only to identify the tea varieties but also to determine simultaneously some chemical compositions contents in tea.     

Effect of temperature variation on the visible and near infrared spectra of wine and the consequences on the partial least square calibrations developed to measure chemical composition

Many studies have reported the use of near infrared (NIR) spectroscopy to characterize wines or to predict wine chemical composition. However, little is known about the effect of variation in temperature on the NIR spectrum of wine and the subsequent effect on the performance of calibrations used to measure chemical composition. Several parameters influence the spectra of organic molecules in the NIR region, with temperature being one of the most important factors affecting the vibration intensity and frequency of molecular bonds. Wine is a complex mixture of chemical components (e.g. water, sugars, organic acids, and ethanol), and a simple ethanol and water model solution cannot be used to study the possible effects of temperature variations in the NIR spectrum of wine. Ten red and 10 white wines were scanned in triplicate at six different temperatures (25 °C, 30 °C, 35 °C, 40 °C, 45 °C and 50 °C) in the visible (vis) and NIR regions (400-2500 nm) in a monochromator instrument in transmission mode (1 mm path length). Principal component analysis (PCA) and partial least squares (PLS) regression models were developed using full cross validation (leave-one-out). These models were used to interpret the spectra and to develop calibrations for alcohol, sugars (glucose + fructose) and pH at different temperatures. The results showed that differences in the spectra around 970 nm and 1400 nm, related to OH bonding were observed for both varieties. Additionally an effect of temperature on the vis region of red wine spectra was observed. The standard error of cross validation (SECV) achieved for the PLS calibration models tended to inverse as the temperature increased. The practical implication of this study it is recommended that the temperature of scanning for wine analysis using a 1 mm path length cuvette should be between 30 °C and 35 °C.     

Partial least squares and principal components analysis of wine vintage by high performance liquid chromatography with chemiluminescence detection

HPLC with acidic potassium permanganate chemiluminescence detection was employed to analyse 17 Cabernet Sauvignon wines across a range of vintages (1971-2003). Partial least squares regression analysis and principal components analysis was used in order to investigate the relationship between wine composition and vintage. Tartaric acid, vanillic acid, catechin, sinapic acid, ethyl gallate, myricetin, procyanadin B and resveratrol were found to be important components in terms of differences between the vintages.     

Adulteration of diesel/biodiesel blends by vegetable oil as determined by Fourier transform (FT) near infrared spectrometry and FT-Raman spectroscopy

In this work it has been shown that the routine ASTM methods (ASTM 4052, ASTM D 445, ASTM D 4737, ASTM D 93, and ASTM D 86) recommended by the ANP (the Brazilian National Agency for Petroleum, Natural Gas and Biofuels) to determine the quality of diesel/biodiesel blends are not suitable to prevent the adulteration of B2 or B5 blends with vegetable oils. Considering the previous and actual problems with fuel adulterations in Brazil, we have investigated the application of vibrational spectroscopy (Fourier transform (FT) near infrared spectrometry and FT-Raman) to identify adulterations of B2 and B5 blends with vegetable oils. Partial least square regression (PLS), principal component regression (PCR), and artificial neural network (ANN) calibration models were designed and their relative performances were evaluated by external validation using the F-test. The PCR, PLS, and ANN calibration models based on the Fourier transform (FT) near infrared spectrometry and FT-Raman spectroscopy were designed using 120 samples. Other 62 samples were used in the validation and external validation, for a total of 182 samples. The results have shown that among the designed calibration models, the ANN/FT-Raman presented the best accuracy (0.028%, w/w) for samples used in the external validation.     

Chemometric models for the quantitative descriptive sensory analysis of Arabica coffee beverages using near infrared spectroscopy

Mathematical models based on chemometric analyses of the coffee beverage sensory data and NIR spectra of 51 Arabica roasted coffee samples were generated aiming to predict the scores of acidity, bitterness, flavour, cleanliness, body and overall quality of coffee beverage. Partial least squares (PLS) were used to construct the models. The ordered predictor selection (OPS) algorithm was applied to select the wavelengths for the regression model of each sensory attribute in order to take only significant regions into account. The regions of the spectrum defined as important for sensory quality were closely related to the NIR spectra of pure caffeine, trigonelline, 5-caffeoylquinic acid, cellulose, coffee lipids, sucrose and casein. The NIR analyses sustained that the relationship between the sensory characteristics of the beverage and the chemical composition of the roasted grain were as listed below: 1 - the lipids and proteins were closely related to the attribute body; 2 - the caffeine and chlorogenic acids were related to bitterness; 3 - the chlorogenic acids were related to acidity and flavour; 4 - the cleanliness and overall quality were related to caffeine, trigonelline, chlorogenic acid, polysaccharides, sucrose and protein.     

Multivariate calibration by partial least squares for the quantitative phase analysis using Rietveld method

The present work used multivariate calibration by Partial Least Squares (PLS) to produce a Net Analyte Signal as a way of establishing the independent influence of each phase in the Quantitative Phase Analysis with the Rietveld method for three sources of potential error: preferred orientation, linear absorption and counting statistics. Ternary mixtures of Al₂O₃, MgO and NiO were employed and organized in three groups with different degrees of variation in the weight fractions of the three constituents. An analysis of variance indicated that the partial selectivity of the least variation group differed significantly from the other groups. As for the phases, MgO partial selectivity was significantly different. This is due to a strong correlation between the linear absorption and counting statistics in the region of the (2 0 0) reflection of the MgO phase that is strongly affected by preferred orientation and also corresponds to the strongest reflection for MgO as well as for NiO. On the whole, by using matrices of similarity, a great similarity was observed between the nominal weight fractions of the phases and the weight fractions observed by means of the Rietveld method. However, such similarity diminishes as the weight fractions of the phases of the mixture become closer to each other and, in the group of mixtures with least variation of weight fractions, the method is unable to quantify the small differences between the phases, even if these errors may be considered small relative to the weight fractions themselves. Copyright © 2008 John Wiley & Sons, Ltd.     

Selecting the optimum number of partial least squares components for the calibration of attenuated total reflectance-mid-infrared spectra of undesigned kerosene samples

Selecting the correct dimensionality is critical for obtaining partial least squares (PLS) regression models with good predictive ability. Although calibration and validation sets are best established using experimental designs, industrial laboratories cannot afford such an approach. Typically, samples are collected in an (formally) undesigned way, spread over time and their measurements are included in routine measurement processes. This makes it hard to evaluate PLS model dimensionality. In this paper, classical criteria (leave-one-out cross-validation and adjusted Wold's criterion) are compared to recently proposed alternatives (smoothed PLS-PoLiSh and a randomization test) to seek out the optimum dimensionality of PLS models. Kerosene (jet fuel) samples were measured by attenuated total reflectance-mid-IR spectrometry and their spectra where used to predict eight important properties determined using reference methods that are time-consuming and prone to analytical errors. The alternative methods were shown to give reliable dimensionality predictions when compared to external validation. By contrast, the simpler methods seemed to be largely affected by the largest changes in the modeling capabilities of the first components.     

Improvement of multivariate calibration techniques applied to 1-to-N component mixtures through an optimized experimental design

This work describes a novel experimental design aimed at building a calibration set constituted by samples containing a different number of components. The algorithm performs a reiteration process to maintain the number of samples at the lower value as possible and to ensure an homogeneous presence of all the concentration levels. The mixture design was applied to a drug system composed by one-to-four components in different combination. The resolution of the system was performed by three multivariate UV spectrophotometric methods utilizing principal component regression (PCR) and partial last squares (PLS1 and PLS2) algorithms. The calibration set was composed by 61 references on four concentration levels, including 15 samples for each quaternary, ternary and binary composition and 16 one-component samples. The calibration models were optimized through a careful selection of number of factors and wavelength zones, in such a way as to remove interferences from instrumental noise and excipients present in the pharmaceutical formulations. The prediction power of the regression models were verified and compared by analysis of an external prediction set. The models were finally used to assay pharmaceutical specialities containing the studied drugs in one-to-four formulations.     

Multicomponent flow injection based analysis with diode array detection and partial least squares multivariate calibration evaluation. Rapid determination of Ca(II) and Mg(II) in waters and dialysis liquids

Flow injection analysis (FIA) with multiwavelength scanning of the FIA peaks using a diode array detector (DAD) has been combined with a multivariate calibration approach applying the partial least squares (PLS) method for the data evaluation. In this way, various side effects like dilution of the reagent, high blank, absorbance changes due to the pH gradient throughout the peak and/or the other interferences can be accounted for. Thus, even with a simple FIA manifold instrumentation the satisfactory results of multicomponent analysis are obtained. The method described has been checked on analysis of binary (Ca and Mg) and ternary (Ca, Mg and Cu) mixtures with pyridylazo resorcinol (PAR) as reagent and applied for rapid determination of calcium and magnesium in dialysis liquids and waters.     

Discrimination of industrial products by on-line near infrared spectroscopy with an improved dendrogram

Near infrared(NIR) spectroscopy technique has shown great power and gained wide acceptance for analyzing complicated samples.The present work is to distinguish different brands of tobacco products by using on-line NIR spectroscopy and pattern recognition techniques.Moreover,since each brand contains a large number of samples,an improved dendrogram was proposed to show the classification of different brands.The results suggest that NIR spectroscopy combined with principal component analysis (PCA) and hierarchical cluster analysis(HCA) performs well in discrimination of the different brands,and the improved dendrogram could provide more information about the difference of the brands.