Artificial neural networks study of the catalytic reduction of resazurin: stopped-flow injection kinetic-spectrophotometric determination of Cu(II) and Ni(II)

An artificial neural network (ANN) procedure was used in the development of a catalytic spectrophotometric method for the determination of Cu(II) and Ni(II) employing a stopped-flow injection system. The method is based on the catalytic action of these ions on the reduction of resazurin by sulfide. ANNs trained by back-propagation of errors allowed us to model the systems in a concentration range of 0.5-6 and 1-15 mg l⁻¹ for Cu(II) and Ni(II), respectively, with a low relative error of prediction (REP) for each cation: REP_Cu(II) = 0.85% and REP_Ni(II) = 0.79%. The standard deviations of the repeatability (s_r) and of the within-laboratory reproducibility (s_w) were measured using standard solutions of Cu(II) and Ni(II) equal to 2.75 and 3.5 mg l⁻¹, respectively: s_r[Cu(II)] = 0.039 mg l⁻¹, s_r[Ni(II)] = 0.044 mg l⁻¹, s_w[Ni(II)] = 0.045 mg l⁻¹ and s_w[Ni(II)] = 0.050 mg l⁻¹. The ANNs-kinetic method has been applied to the determination of Cu(II) and Ni(II) in electroplating solutions and provided satisfactory results as compared with flame atomic absorption spectrophotometry method. The effect of resazurin, NaOH and Na₂S concentrations and the reaction temperature on the analytical sensitivity is discussed.     

Use of the molybdenum-thiocyanate-rhodamine 6G ternary complex for spectrophotometric molybdenum determination without extraction

A modified thiocyanate method without extraction by using rhodamine 6G as a secondary ligand was developed. Molybdenum in 1.0×10⁻² M HCl, after the addition of ascorbic acid, was heated for 10 min in a 90 °C water bath for reduction. Suitable amounts of glycerine, Triton X-100, rhodamine 6G solutions and 2+1 (v/v) 9 M H₂SO₄+3 M KHSO₄ were added in this order. This solution was allowed to cool to room temperature and the absorbance at 570 nm was measured against a reagent blank 45 min after the addition of thiocyanate solution and the second aliquot of Triton X-100 solution. The complex was stable for at least 4 h, the order of reagent addition was important, and thiocyanate should be in large excess. Beer’s law was obeyed over the range 0.9×10⁻⁶ to 1.1×10⁻⁵ M Mo with the molar absorptivity being 1.1×10⁵ l mol⁻¹ cm⁻¹. The R.S.D. for the determination of 0.7 mg Mo l⁻¹ was 1.83% (n=8). Possible interferences of various cations and anions on molybdenum determination were studied. The proposed method was applied to the determination of molybdenum in a dental alloy, Wiron 99.     

Fluorescence anisotropy: application in quantitative enzymatic determinations

In this work a method is presented for the enzymatic determination of glucose using fluorescence anisotropy. During the enzymatic reaction a change in the fluorescence anisotropy of the glucose oxidase (GOx) is produced; the reaction time at which this change appears (t_m) depends on the glucose concentration. A theoretical study has been developed which enables: (a) the correlation of this change in anisotropy with changes in the intensity and the lifetime of the enzyme fluorescence; from this a model which could be generalized to other flavo-enzymes is proposed; (b) the linking of t_m with glucose concentration.After optimisation, the proposed method allows the determination of glucose over the range 100-1000 mg l⁻¹. The detection limit is 90 mg l⁻¹and the reproducibility is better than 4% (n = 6, [glucose] = 250 mg l⁻¹). Anisotropy is more selective than conventional fluorescence intensity, and this method has therefore been applied to direct glucose determination in fruit juices without the interference caused by the inner filter effect.     

Sequential injection method for the direct spectrophotometric determination of bismuth in pharmaceutical products

A spectrophotometric method is reported for the determination of bismuth in pharmaceutical products using sequential injection analysis. Methylthymol blue (MTB) was used as a color forming reagent and the absorbance of the Bi(III)-MTB complex was monitored at 548 nm. The various chemical and physical variables that affected the reaction were studied. A linear calibration graph was obtained in the range 0.0-75.0 mg l⁻¹ Bi(III) at a sampling frequency of 72 h⁻¹. The reagent consumption was considerably reduced compared to conventional flow injection systems, as only 150 μl of MTB were consumed per run. The precision was very satisfactory (s_r=0.5%, at 50.0 mg l⁻¹ Bi(III), n=12) and the limit of detection, c_L, was 0.250 mg l⁻¹. The developed method was applied successfully to the analysis of various pharmaceutical products containing Bi(III). The relative errors e_r, were <1.5% in all cases and were evaluated by comparison of the obtained results with those found using atomic absorption spectrometry as the reference method.     

Determination of methimazole and carbimazole by flow-injection with chemiluminescence detection based on the inhibition of the Cu(II)-catalysed luminol-hydrogen peroxide reaction

This paper reports an indirect flow-injection (FI) method for the determination of the anti-hyperthyroid drugs methimazole and carbimazole in pharmaceuticals. The method was based on the inhibition that these thioimidazole drugs caused on the Cu(II)-catalysed chemiluminescence (CL) reaction between luminol and H₂O₂. The CL reaction was induced on-line and injection of the sample produced negative peaks as a result of the Cu(II) complexation by the analytes. The height of the FI peaks was proportional to the drug concentration in the sample. The linear range was 2-100 and 3-120 mg l⁻¹ for methimazole and carbimazole, respectively. The relative standard deviation was 1.9% for methimazole and 2.1% for carbimazole at the 50 mg l⁻¹ level (n=10). Common excipients present in pharmaceutical tablets were found not to interfere with the analysis. The method was applied to the determination of methimazole and carbimazole in pharmaceutical formulations with recoveries in the range 100±4%.     

Selective stopped-flow sequential injection method for the spectrophotometric determination of titanium in dental implant and natural Moroccan phosphate rock

The present work reports the first sequential injection (SI) method for the spectrophotometric determination of Ti(IV). The method is based upon the reaction of Ti(IV) with chromotropic acid (CA) in acidic medium to form a water-soluble complex (λ_max = 420 nm). The chemical and instrumental variables of the system that affected the reaction were studied. Selectivity was greatly enhanced using ascorbic acid. A linear calibration graph was obtained in the range 0.2-10.0 mg l⁻¹ Ti(IV) at a sampling frequency of 24 h⁻¹. The precision was satisfactory (s_r = 1.5% at 5.0 mg l⁻¹ Ti(IV), n = 12) and the 3σ limit of detection, c_L, was 0.7 mg l⁻¹ (n = 10). The developed method proved to be adequately selective and was applied successfully to the analysis of real samples (dental implant and natural Moroccan phosphate rock) giving accurate results based on recovery studies (98-105%).     

Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l⁻¹ for copper and 0.1-5 mg l⁻¹ for iron, respectively, with a sampling rate of 18 h⁻¹. The limits of detection are 50 μg l⁻¹ for copper and 25 μg l⁻¹ for iron. The relative standard deviations (n = 15) are 2% for 0.5 mg l⁻¹ copper and 1.8% for 0.5 mg l⁻¹ iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l⁻¹ of copper and 0.2-5 mg l⁻¹ of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.     

A multicommuted flow system for sequential spectrophotometric determination of hydrosoluble vitamins in pharmaceutical preparations

A multicommuted flow system is proposed for spectrophotometric determination of hydrosoluble vitamins (ascorbic acid, thiamine, riboflavine and pyridoxine) in pharmaceutical preparations. The flow manifold was designed with computer-controlled three-way solenoid valves for independent handling of sample and reagent solutions and a multi-channel spectrophotometer was employed for signal measurements. Periodic re-calibration as well as the standard addition method was implemented by using a single reference solution. Linear responses (r=0.999) were obtained for 0.500-10.0 mg l⁻¹ ascorbic acid, 2.00-50.0 mg l⁻¹ thiamine, 5.00-50.0 mg l⁻¹ riboflavine and 0.500-8.00 mg l⁻¹ pyridoxine. Detection limits were estimated as 0.08 mg l⁻¹ (0.5 μmol l⁻¹) ascorbic acid, 0.8 mg l⁻¹ (2 μmol l⁻¹) thiamine, 0.2 mg l⁻¹ (0.5 μmol l⁻¹) riboflavine and 0.1 mg l⁻¹ (0.9 μmol l⁻¹) pyridoxine at 99.7% confidence level. A mean sampling rate of 60 determinations per hour was achieved and coefficients of variation of 1% (n=20) were estimated for all species. The mean reagent consumption was 25-fold lower in relation to flow-based procedures with continuous reagent addition. Average recoveries between 95.6 and 100% were obtained for commercial pharmaceutical preparations. Results agreed with those obtained by reference methods at 95% confidence level. The flow system is suitable for application in quality control processes and in dissolution studies of vitamin tablets.     

Method for monitoring urea and ammonia in wine and must by flow injection-pervaporation

An easy to automate flow injection-pervaporation method for monitoring urea and ammonia in must and wine was developed. The method is based on separation of the ammonia from the sample matrix by pervaporation followed by its reaction with salicylate, hypochlorite and nitroprusside to form a diazonium salt with maximum absorption at 647 nm. Conversion of urea into ammonia catalysed by urease was mandatory before pervaporation. After optimisation by either the univariate or multivariate approaches as required, the linear range was established (between 0 and 25 mg l⁻¹) for both analytes. Then, the assessment of the proposed method versus a reference one for urea and ammonia was studied in terms of repeatability (0.52 and 0.43 mg l⁻¹, respectively), reproducibility (1.34 and 1.21 mg l⁻¹, respectively), detection and quantification limits (LOD=0.9 and 0.6 mg l⁻¹, LQ=1.02 and 0.67 mg l⁻¹, respectively) and traceability. The sample throughput was 16 samples h⁻¹. The method can be applied to the monitoring of the target analytes in must and young wine in order to control their contents, preventing formation of ethyl carbamate.     

Chemiluminometric determination of the pesticide 3-indolyl acetic acid by a flow injection analysis assembly

A new method is proposed for the chemiluminescent determination of the pesticide 3-indolyl acetic acid by means of an flow injection analysis system. The chemiluminescence emission is obtained by oxidation of the analyte with Ce (IV) in nitric acid and presence of β-cyclodextrine.The continuous-flow method allows the determination of 159 samples h⁻¹ of 3-indolyl acetic acid in an interval of concentrations over the range 0.5-15.0 mg l⁻¹. The limit of detection was 0.1 μg l⁻¹ and the R.S.D. (n, 17) at 2.0 mg l⁻¹ of the pesticide level was 2.7%. The method was applied to water samples.     

Determination of bismuth and zinc in pharmaceuticals by first derivative UV-Visible spectrophotometry

A first order derivative spectrophotometric method has been developed for the simultaneous determination of bismuth and zinc by dithizone without time-consuming extraction step. The reactions of bismuth and zinc with dithizone in a three component solution prepared in water, acetone and n-propanol mixture have been investigated. These cations react with dithizone in this mixture at pH 5.0, forming coloured complex that is stable for at least 2 h. The linear range in D evaluation was between 3.0 × 10⁻⁶ and 1.8 × 10⁻⁵ mol l⁻¹ for Zn and 2.4 × 10⁻⁶ and 1.2 × 10⁻⁵ mol l⁻¹ for Bi. The limits of detection for the analytical procedure were found 0.05 mg l⁻¹ for both cations. The relative standard deviations for the determination of 0.5 mg l⁻¹ bismuth and 0.5 mg l⁻¹ zinc were 1.2 and 1.1%, respectively, for five determinations. The procedure is simple, rapid and reliable. This method was applied to the determination of bismuth and zinc in the pharmaceutical materials successfully. Good agreement was achieved between the results obtained by the proposed and comparative methods.     

Sequential injection spectrophotometric determination of phenylephrine hydrochloride in pharmaceutical preparations

A fully automated sequential injection spectrophotometric method for the determination of phenylephrine hydrochloride in pharmaceutical preparations is reported. The method is based on the condensation reaction of the analyte with 4-aminoantipyrine in the presence of potassium ferricyanide. The absorbance of the condensation product was monitored at 503 nm. A linear relationship between the relative peak height and concentration was obtained in the range 0.5-17.5 mg l⁻¹. The detection limit (as 3σ value) was 0.09 mg l⁻¹ and repeatability was 0.8 and 0.6% at 2.5 and 5 mg l⁻¹, respectively. Results obtained by this method agreed very well with those obtained by the AOAC official method.     

Selective determination of cyanides by gas diffusion-stopped flow-sequential injection analysis and an on-line standard addition approach

A highly selective sequential injection (SI) method for the automated determination of weak-acid-dissociable cyanides is reported. The analytical procedure is based on the on-line reaction of the analyte with ninhydrin in carbonate medium to form a coloured product (λ_max = 510 nm). Cyanides are removed from sample matrix by acidification through a gas-diffusion step incorporated in the SI manifold. The effect of instrumental and chemical variables was studied. By adopting an on-line standard addition protocol, the sensitivity of the proposed method was enhanced drastically, without affecting the determination range. The assay was validated in terms of linearity (up to 200 μg L⁻¹), limit of detection (c_L = 2.5 μg L⁻¹), limit of quantitation (c_Q = 7.5 μg L⁻¹), precision (s_r < 2.5% at 100 μg L⁻¹) and selectivity. High tolerance against critical species such as sulfides and thiocyanates was achieved. The applicability of the method was demonstrated by analyzing tap and mineral water samples at levels below the limits established by international E.U. and U.S. organizations. The percent recoveries were satisfactory in all cases, ranging between 94.2 and 103.6%.     

Reversed flow injection spectrophotometric determination of chlorate

An interfacing has been developed to connect a spectrophotometer with a personal computer and used as a readout system for development of a simple, rapid and sensitive reversed flow injection (rFI) procedure for chlorate determination. The method is based on the oxidation of indigo carmine by chlorate ions in an acidic solution (dil. HCl) leading to the decrease in absorbance at 610 nm. The decrease in absorbance is directly related to the chlorate concentration present in the sample solutions. Optimum conditions for chlorate were examined. A linear calibration graph over the range of 0.1-0.5 mg L⁻¹ chlorate was established with the regression equation of Y = 104.5X + 1.0, r² = 0.9961 (n = 6). The detection limit (3σ) of 0.03 mg L⁻¹, the limit of quantitation (10σ) of 0.10 mg L⁻¹ and the RSD of 3.2% for 0.3 mg L⁻¹ chlorate (n = 11) together with a sample throughput of 92 h⁻¹ were obtained. The recovery of the added chlorate in spiked water samples was 98.5 ± 3.1%. Major interferences for chlorate determination were found to be BrO₃⁻, ClO₂⁻, ClO⁻ and IO₃⁻ which were overcome by using SO₃²⁻ (as Na₂SO₃) as masking agent. The method has been successfully applied for the determination of chlorate in spiked water samples with the minimum reagent consumption of 14.0 mL h⁻¹. Good agreement between the proposed rFIA and the reference methods was found verified by Student's t-test at 95% confidence level.     

A multisyringe sequential injection method for monitoring water in the energy cogeneration system of a municipal waste incinerator

Leading-edge urban solid waste ashing plants use burning heat energy to obtain electrical power. Water fed to their boilers for conversion into steam should be highly pure in order to minimize corrosion, scaling and similar phenomena, which can lead to malfunctioning and a reduced useful life but can be avoided by proper management and control of the water supply. In this work, we developed a multiparameter monitor based on multisyringe sequential injection for the sequential determination of up to eight important parameters, namely: pH, specific and acid conductivity, hydrazine, ammonium, phosphate, silicate and total iron.Acid conductivity was determined by passing the sample through a cation-exchange resin in order to retain ammonium ion and release protons. This parameter was deemed the most accurate indicator of dissolved solids in boiler water. Chemical parameters were determined spectrophotometrically: hydrazine by reaction with p-dimethylaminobenzaldehyde, ammonium by the modified Berthelot reaction, iron with o-phenanthroline, and phosphate and silica by formation of a molybdoheteropoly blue dye in the presence of ascorbic acid as reductant. Use of the optimum chemical and physical operating conditions provided 3s_blank detection limits of 0.01 mg l⁻¹ N₂H₄, 0.13 mg l⁻¹ NH₄⁺, 0.04 mg l⁻¹ Fe, 0.03 mg l⁻¹ SiO₂ and 0.05 mg l⁻¹ PO₄³⁻, and relative standard deviations not greater than 2.5%. The methods integrated in the proposed monitor were successfully applied to real samples from the water-steam cycle at the Son Reus ashing plant in Palma de Mallorca (Spain).     

High speed liquid chromatography for in-process control of rifabutin

A fast HPLC method has been developed for simultaneous determination of rifabutin and its synthesis precursors. The analytes are separated in 1.8 min by means of a Kromasil 100 C₁₈ column (50 mm × 2.1 mm i.d., 3.5 μm) at 30 °C. The mobile phase (A: 5 mM KH₂PO₄ adjusted to pH 6.5 with KOH; B: acetonitrile) was pumped at a flow rate of 0.4 ml min⁻¹ according to the fast gradient mode: 0 min, 58% B; 0-0.4 min, 95% B. Detection was by ultraviolet absorbance at 275 nm. The method was validated in accordance with the International Conference on Harmonisation (ICH) guidelines and good accuracy, intermediate precision (≤4.6%) and linearity in the range 5-50 mg l⁻¹ were observed for all compounds. This method is sensitive (limits of detection ranged between 0.1 and 0.3 mg l⁻¹) and selective to quantify rifabutin and its synthesis precursors and could be used for in-process control.     

Spectrofluorimetric determination of tannins based on their activative effect on the Cu(II) catalytic oxidation of rhodamine 6G by hydrogen peroxide

A simple and highly sensitive kinetic fluorimetric method is proposed for the determination of trace tannins, based on the activation of tannins on the oxidation of rhodamine 6G (Rh 6G) by hydrogen peroxide catalyzed by Cu(II) ion. The calibration graph was rectilinear in the range 0.08-1.28 mg l⁻¹ for tannin, the 3σ detection limit for tannin is 0.0455 mg l⁻¹. The relative standard deviation for 11 determinations of 0.4 mg l⁻¹ tannin is 0.96%. The proposed method has been successfully used to determine tannins in tea and Chinese gall. The results obtained were compared with those provided by the Folin-Ciocalteu method. This is the first procedure to be reported for the determination of tannins based on fluorimetric measurements.     

A flow sampling strategy for the analysis of oil samples without pre-treatment in a sequential injection analysis system

The present work describes a sequential injection analysis (SIA) system adapted to direct analysis of oil samples. In this way, the flow system was designed by incorporation, in the SIA system, of an injection valve that was responsible for the sample insertion. With the developed sampling strategy the sample pre-treatment outside the flow system is avoided and also the problems associated with viscous samples in flow systems.The developed SIA system was applied to the determination of iron (Fe(III)) in edible oil samples and was based on the formation of a red complex (λ = 510 nm) between Fe(III) and thiocyanate in organic medium. A mixture of methanol:chloroform (85:15) was used as carrier solution and possible refractive index associated with the spectrophotometric detection was avoided by introduction of a mixing chamber in the flow system. The presented methodology produced 4.2 ml of effluent and consumed 150 μl of sample and 0.95 mg of thiocyanate per determination.Linear calibration plots were obtained for Fe(III) concentrations up to 25 mg l⁻¹ and the detection limit of the determination was 0.31 mg l⁻¹. The developed methodology exhibited a good precision, with an R.S.D. < 3.5% (n = 15) and a determination frequency of 20 determinations h⁻¹. The results of the analysis were evaluated by recovery studies (96.5-104.5%) and by the analysis of two AOCS reference samples.     

Determination of myo-inositol hexakisphosphate (phytate) in urine by inductively coupled plasma atomic emission spectrometry

Myo-inositol hexakisphosphate (phytate) is a substance present in urine with an important role in preventing calcium renal calculi development. In spite of this, the use of urinary phytate levels on stone-formers’ evaluation and treatment is still notably restricted as a consequence of the enormous difficulty to analyze this substance in urine. In this paper, a simple procedure for routinary urinary phytate determination based on phosphorus determination through inductively coupled plasma atomic emission spectrometry is described.The method only requires a previous separation of phytate from other components by column anion exchange chromatography. The working linear range used was 0-2 mg l⁻¹ phosphorus (0-7 mg l⁻¹ phytate). The limit of detection was 64 μg l⁻¹ of phytate and the limit of quantification was 213 μg l⁻¹. The relative standard deviation (R.S.D.) for 1.35 mg l⁻¹ phytate was 2.4%. Different urine samples were analyzed using an alternative analytical methodology based on gas chromatography (GC)/mass detection used for inositol determination (phytate was previously hydrolyzed), resulting both methods comparable using as criterion to assess statistical significance P<0.05.