Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

Transport properties of SrCe0.95Y0.05O3−δ and its application for hydrogen separation

Transport properties of SrCe_0.95Y_0.05O_3−δ were studied by impedance spectroscopy and by measuring open-cell voltage (OCV) and gas permeation. Ionic transference numbers were determined by measuring the OCV of concentration cells and water vapor evolution of an O₂/H₂ fuel cell. We observed interfacial polarization on the basis of the I–V curves obtained by discharging a hydrogen concentration cell or an O₂/H₂ fuel cell. The observed high protonic conductivity (high proton and low oxide ion transference numbers) makes SrCe_0.95Y_0.05O_3−δ a potential material for hydrogen separation. From proton conductivity measurements, under a given hydrogen partial pressure difference of 4%/0.488%, the hydrogen permeation rate (of a dense membrane with 0.11 cm in thickness) was calculated to be ≈0.072 cm³ (STP) cm⁻² min⁻¹ at 800°C, whereas the permeation rate calculated from short-circuit current measurements was ≈0.023 cm³ (STP) cm⁻² min⁻¹ at 800°C. The difference between calculated and observed permeation rates is probably due to interfacial polarization.     

Study of the interfacial structure and chemistry of CVD κ-Al2O3/TiC multilayer coatings

This article describes the interfacial regions in CVD grown TiC/κ-Al₂O₃ multilayers. A number of microanalytical techniques were used including HREM, EDX and EELS. Occasionally, the first 50 nm of the alumina layers deposited on the intermediate TiC layers grew as a cubic alumina, heavily faulted, containing small amounts of sulphur (S), maybe as a stabiliser. The presence of slightly rounded TiC (111) facets may act as preferred nucleation sites for the cubic Al₂O₃ phase, with a ‘cube on cube’ orientation relationship. In this way the nucleation of κ-Al₂O₃ is less favourable. After some tens of nanometres the cubic phase cannot be stabilised any longer and the layer continues to grow as κ-Al₂O₃. A number of observations point towards the reaction zone (RZ) being η- and/or γ-Al₂O₃. The diffraction work and the FFT analysis of the HREM images show that the RZ is an fcc phase with a=7.9 Å, which matches with η- and γ-Al₂O₃. The EELS Al fine structure indicate more tetrahedral Al ions than in κ-Al₂O₃, as in η- and γ-Al₂O₃. The RZ contains small amounts of S, as has been reported for γ-Al₂O₃. Due to the structural similarities between η- and γ-Al₂O₃ it was not possible to determine which of these cubic phases is present in the RZ.     

Structural and lithium intercalation studies of Mn(0.5−x)CaxTi2(PO4)3 phases (0≤x≤0.50)

Materials from the Mn_(0.5−x)Ca_xTi₂(PO₄)₃ (0≤x≤0.50) solid solution were obtained by solid-state reaction in air at 1000 °C. Selected compositions were investigated by powder X-ray diffraction analysis, ³¹P nuclear magnetic resonance (NMR) spectroscopy and electrochemical lithium intercalation. The structure of all samples determined by Rietveld analysis is of the Nasicon type with the R space group. Mn²⁺/Ca²⁺ ions occupy only the M1 sites in the Ti₂(PO₄)₃ framework. The divalent cations are ordered in one of two M1 sites, except for the Mn_0.50Ti₂(PO₄)₃ phase, where a small departure from the ideal order is observed by XRD and ³¹P MAS NMR. The electrochemical behaviour of Mn_0.50Ti₂(PO₄)₃ and Mn_(0.5−x)Ca_xTi₂(PO₄)₃ phases was characterised in Li cells. Two Li ions can be inserted without altering the Ti₂(PO₄)₃ framework. In the 0≤y≤2 range, the OCV curves of Li//Li_yMn_0.50Ti₂(PO₄)₃ cells show two main potential plateaus at 2.90 and 2.50–2.30 V. Comparison between the OCV curves of Li//Li_(1+y)Ti₂(PO₄)₃ and Li//Li_yMn_0.50Ti₂(PO₄)₃ shows that the intercalation occurs first in the unoccupied M1 site of Mn_0.50Ti₂(PO₄)₃ at 2.90 V and then, for compositions y>0.50, at the M2 site (2.50–2.30 V voltage range). The effect of calcium substitution in Mn_0.50Ti₂(PO₄)₃ on the lithium intercalation is also discussed from a structural and kinetic viewpoint. In all systems, the lithium intercalation is associated with a redistribution of the divalent cation over all M1 sites. In the case of Mn_0.50Ti₂(PO₄)₃, the stability of Mn²⁺ either in an octahedral or tetrahedral environment facilitates cationic migration.     

Fabrication of p-Si/β-FeSi2 balls/n-si structures by MBE and their electrical and optical properties

We report on the formation technique of single-crystalline β-FeSi₂ balls (<100 nm) embedded in a Si p–n junction region by Si molecular beam epitaxy (MBE). β-FeSi₂ films grown on Si (0 0 1) by reactive deposition epitaxy (RDE) aggregated into islands after annealing at 850°C in ultrahigh vacuum. The islands of β-FeSi₂ aggregated further into a ball shape by following the Si MBE overgrowth at 750°C. It was found from X-ray diffraction (XRD) patterns that the epitaxial relationship between the two materials, and single-crystalline nature were preserved even after the annealing and the Si overgrowth. Capacitance–voltage (C–V) characteristics and transmission electron microscope (TEM) images revealed that a lot of defects were introduced around the embedded β-FeSi₂ balls with an increase of embedded β-FeSi₂ quantity.     

Measurement of electro-optic coefficients of low-symmetry crystal YbCa4O(Bo3)3

In this paper, we report on all the electro-optic coefficients of the low-symmetry crystal YbCa₄O(BO₃)₃ measured by the interferometric method. The new sample orientations, which have not been reported so far, have been used for measuring the skew electro-optic coefficients γ₅₁, γ₅₃, γ₄₂ and γ₆₂ independently. The results obtained are γ₁₁=0.6, γ₂₁=0.4, γ₃₁=0.3, γ₁₃=0.3, γ₂₃=0.2, γ₃₃=2.2, γ₅₁=0.9, γ₅₃=4.1, γ₄₂=0.8 and γ₆₂=0.4×10⁻¹² m/V.     

Measurement of electro-optic coefficients of low symmetry crystal GdCa4O(BO3)3

In this paper, we report all of the electro-optic coefficients of the low symmetry crystal GdCa₄O(BO₃)₃ measured by the interferometric method. The new sample orientations, which have not been reported so far, have been used for measuring the skew electro-optic coefficients γ₅₁, γ₅₃, γ₄₂ and γ₆₂ independently. The results obtained are γ₁₁=0.4, γ₂₁=0.5, γ₃₁=0.6, γ₁₃=0.1, γ₂₃=0.4, γ₃₃=2.0, γ₅₁=0.7, γ₅₃=1.5, γ₄₂=0.5, γ₆₂=0.8×10⁻¹²m/V.     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

Deuterium conductivity, diffusion and implantation in Sr-doped LaYO3

A study of deuterium conductivity and diffusion in the oxide perovskite La_0.9Sr_0.1YO_3−δ is presented in this work. Deuterium ions were implanted into La_0.9Sr_0.1YO_3−δ (50 keV, 1×10¹⁶ atoms/cm²) and the corresponding deuterium depth profile was determined by SIMS and compared with a Monte Carlo simulation (TRIM96). This implant was used as a standard for the determination of deuterium concentration in a La_0.9Sr_0.1YO_3−δ sample pre-treated in D₂O atmosphere. In this way, it was fully confirmed that La_0.9Sr_0.1YO_3−δ incorporates water at high temperatures. The conductivity of La_0.9Sr_0.1YO_3−δ was measured in D₂O atmosphere and compared with other proton (deuteron) conductors. Concentration and conductivity data were used in conjunction to estimate the deuterium diffusivity and the constant of reaction of (heavy) water incorporation into LaYO₃. Some comments on the catalytic activity of this oxide are made.     

Phase segregation of LixMn2O4 (0.6<x<1) in non-equilibrium reduction processes

Chemical synthesis routes to Li_xMn₂O₄ (0.15≤x≤1) in non-equilibrium reduction processes were developed to carry out detailed structural analysis. Non-equilibrium Li_xMn₂O₄ (0.15≤x≤1) samples were prepared by chemical lithiation of λ-MnO₂ with LiI for 24 h; longer than 1 week was needed to reach true equilibrium at room temperature. The samples were characterized by X-ray diffraction analysis. The phase diagram was different from that in the equilibrium state; three cubic phases (phases A, B and C) were observed for Li_xMn₂O₄ (0.15≤x≤1). There were two regions of two-phase coexistence: the region of 0.25<x<0.55 (phase B+phase C) and 0.6<x<1.0 (phase A+phase B). In the compositional range of 0.6<x<1.0, the lattice constants of phases A and B change with the lithium composition, this indicates that it is a structural anomaly with a metastable two-phase character in non-equilibrium reduction processes.     

Lithium insertion into Li4V3O8

The lithium insertion characteristics of lithium vanadate, Li₄V₃O₈, were investigated using LiV₃O₈ prepared by the precipitation technique as the starting material. The Li₄V₃O₈ phase was formed by lithiation over x=1.5 in Li_1+xV₃O₈, and the diffusion of lithium in this phase determined the reaction rate of insertion more than x=1.5. Improvement of insertion kinetics in the Li₄V₃O₈ phase extended the lithium insertion limit from x=3.2 to x=4.0, compared with the case of LiV₃O₈ by conventional high temperature synthesis. Lithium insertion proceeds as the single-phase reaction in the range of 3.2<x<4.0.     

Effect of Sn doping on the magnetic and transport properties of LaMnO3+δ

We report the influence of the Sn doping on the magnetotransport properties of the LaMnO_3+δ perovskite. Two series of samples with nominal LaSn_xMn_1−xO_3+δ (I series) and La_{(1−x)/(1+x)}Sn_xMn_1−xO_3+δ (II series) compositions (x=0, 0.025, 0.05 and 0.10) were prepared at T_s=750°C. The M(T) data under 0.01 and 0.5 T for the I series reveal a depressed magnetization as the Sn content increases suggesting the presence of magnetic clusters with a superparamagnetic behavior. Resistivity measurements indicate an insulator material for all Sn content independently of the applied magnetic field. On the contrary, for the II series the M(T) and M(H) data reveal FM behavior and an improvement of the magnetization as Sn increases. These samples show magnetoresistance. The magnetotransport properties are discussed in terms of the presence of A-site cation vacancies.     

Growth of β-MnO2 films on TiO2(110) by oxygen plasma assisted molecular beam epitaxy

We have used oxygen plasma assisted MBE to grow epitaxial films of pyrolusite (β-MnO₂) on TiO₂(110) for thicknesses of one to six bilayers (BL). We define a bilayer to be a layer of Mn and lattice O and an adjacent layer of bridging O within the rutile structure. The resulting surfaces have been characterized in situ by reflection high-energy electron diffraction, low-energy electron diffraction, X-ray photoelectron spectroscopy and diffraction, and atomic force microscopy. Well-ordered, pseudomorphic overlayers form for substrate temperatures between 400 and 500°C. Mn–Ti intermixing occurs over the time scale of film growth (1 BL/min) for substrate temperatures in excess of 500°C. Films grown at 400–500°C exhibit island growth, whereas intermixed films grown at temperatures of 500–600°C are more laminar. 1 BL films grown at 450°C are more laminar than multilayer films grown at the same temperature, and form a well-ordered surface cation layer of Mn on the rutile structure with at most 10% indiffusion to the second cation layer.     

Effect of structural vacancies on lattice vibration,mechanical, electronic,and thermodynamic properties of Cr5BSi3

In recent years,transition metal silicides have become the potential high temperature materials.The ternary silicide has attracted the attention of scientists and researchers.But their inherent brittle behaviors hinder their wide applications.In this work,we use the first-principles method to design four vacancy defects and discuss the effects of vacancy defects on the structural stability,mechanical properties,electronic and thermodynamic properties of hexagonal Cr;BSi;silicide.The data of lattice vibration and thermodynamic parameters indicate that the Cr;BSi;with different atomic vacancies can possess the structural stabilities.The different atomic vacancies change the mechanical properties and induce the Cr;BSi;to implement the brittle-to-ductile transition.The shear deformation resistance and volume deformation resistance of Cr;BSi;are weakened by different vacancy defects.But the brittleness behavior is remarkably improved.The structural stability and brittle-to-ductile transition of Cr;BSi;with different vacancies are explored by the electronic structures.Moreover,the thermal parameters indicate that the Cr;BSi;with vacancies exhibit different thermodynamic properties with temperature rising.     

Correlation between structural and optical properties of ion beam synthesized β-FeSi2 precipitates in Si

The structural and optical properties of β-FeSi₂ precipitates produced by ion beam synthesis have been investigated by transmission electron microscopy, photoluminescence (PL) analysis and near infrared transmission measurements. The PL spectrum of β-FeSi₂ precipitates in a dislocation free sample has been observed to consist of a sharp line at 1.54 μm and a weak peak at 1.46 μm. Optical transmission measurements showed a direct band gap about 0.8 eV smaller than in continuous β-FeSi₂ film. Calculation of the electronic bands of β-FeSi₂ for different values of the lattice parameters indicates that this reduction can be ascribed to band distortion provided by the lattice strain.     

Radiation-induced processes and defects in alkali and alkaline-earth borate crystals

The paper presents the results of a study of the radiation-induced processes and defects in nonlinear optical crystals Li₂B₄O₇ (LTB), LiB₃O₅ (LBO), CsLiB₆O₁₀, KB₅O₈·4H₂O, β-BaB₂O₄. It was revealed that a pulsed electron beam irradiation at 290 K forms the radiation-induced pairs of the ‘vacancy—interstitial atom’ defects in the cation sublattice of these crystals. This gives rise to a creation of metastable electronic (interstitial atom) and hole (small-radius polaron near the cation vacancy) centers in high concentrations. Optical hole-transitions from the local level of the trapped hole centers to the valence band states are responsible for the transient optical absorptions (TOA) of borates in the visible and UV spectral ranges. A sublattice of the weakly bound mobile lithium cations in LTB and LBO favors a spatial separation of the radiation-induced pair defects ‘hole polaron near Li-vacancy—mobile interstitial Li⁰ atom’. Their decay rated by the electron–hole nonradiative tunnel recombination determines a peculiar feature of the TOA decay kinetics in LTB and LBO.     

Solid-state synthesis of potassium β- and β″-gallates

Direct synthesis of K-β- and β″-gallates by Ga₂O₃–K₂O solid-state reaction is described. The formation of K-β- or β″-gallates depends on the initial Ga₂O₃ phase. -Ga₂O₃ leads to K-β-gallate; β-Ga₂O₃ leads to K-β″-gallate. K-β″-Gallate is stable <1200°C. The high temperature stability of K-β″-gallate can be enhanced by doping with aliovalent ions.     

Comblike polymer electrolyte with main chain glass transition near room temperature

A new amorphous comblike polymer (CBP) based on methylvinyl ether/maleic anhydride altering copolymer backbone and on oligooxyethylene side chain was synthesized. The dynamic mechanical properties of CBP and its Li salt complexes were investigated by means of DDV-ll-EA type viscoelastic spectrometry. Results showed that there were two glass transitions (-transition and β-transition) in the temperature range from − 100 to 100 °C. The β-transition was assigned to oligo-PEO side chains and the temperature of β-transition increases with increasing Li salt content. The -transition was assigned to the main chain of CBP. The temperature of the -transition (T) is also dependent upon the Li-salt content, but not monotonie. The value of T lies between 30–45 °C in the Li salt concentration range studied, near room temperature. It was found that the CBP-Li salt complexes showed an unusual dependence of ionic conductivity on Li salt content. There are two peaks in the plot of the ionic conductivity vs. Li salt concentration, which has been ascribed to the movability of the CBP main chain at ambient temperature. The temperature dependence of the ionic conductivity indicated that the Arrhenius relationship was not obeyed, and the plot of log σ against 1/(T − T₀) showed the unusual dual VTF behavior when using side chain glass transition temperature (T_β) as T₀.     

Luminescence from γ-irradiated humic acid

This study was conducted to investigate the ultraweak delayed radiochemiluminescence (RCL) spectra, kinetics and spectroscopic properties of humic acids (HAs) after γ-radiation exposure (absorbed doses of 1−10 kGy, Co-60) in model systems.

The kinetics and spectral distribution of RCL (340–650 nm) were measured using the single photon counting (SPC) method and cut-off filters.

The intensity of fluorescence (λ_ex=390, 440, 490 and 540 nm) covering the spectral range 400–580 nm was heavily dependent on the λ_ex and slightly increased with the absorbed dose of γ-radiation.

Absorption spectra (the range 240−800 nm) and color coefficients E_2.6/4 and E_4/6 of irradiated solutions indicated that post-radiative degradation/polymerization processes take place in the HA, changing their macromolecule size or properties.

Comparison of FTIR spectra and elemental analysis proved an increased O and decreased C atoms in irradiated samples. The data indicate on the radiolysis-induced degradation of native HA into fulvic-like acids with higher hydrophilicity and lower molecular size.