Direct determination of arsine in gases by inductively coupled plasma-dynamic reaction cell-mass spectrometry

Reliable determination of arsine (AsH₃) in gases is of great importance due to stringent regulations associated with health, safety and environmental issues. It is, however, challenging for an analyst to determine trace airborne arsine concentrations without specifically designed collection procedures using adsorption, desorption, dissolution or impinging techniques. To circumvent such technical barrier, we have newly developed a direct analytical method, characterized by introduction of an arsine gas sample into stable plasma stream, followed by gas-phase oxidation of arsine with molecular oxygen in a dynamic reaction cell (DRC) equipped within the inductively coupled plasma-mass spectrometry (ICP/MS) system, followed by subsequent detection of AsO⁺ ion. This preliminary work used trace arsine concentrations (161 μg m⁻³, 322 μg m⁻³, and 645 μg m⁻³) gravimetrically prepared in N₂ balance. The proposed method was optimized for the important experimental parameters such as the flow rates of the reaction gas, the arsine sample, and the carrier gas. This method was then validated by demonstrating good figure-of-merits including the low limit of detection (0.10 μg m⁻³), good linearity (r² > 0.9915), low measurement uncertainty (0.66%), and high speed of analysis (<6 min). The proposed method is expected to be potentially applicable to the determination of arsine in real workplace air after appropriate modifications are made.     

Determination of the ratio of calcium to phosphorus in foodstuffs by dynamic reaction cell inductively coupled plasma mass spectrometry

An inductively coupled plasma mass spectrometer (ICP–MS) equipped with a dynamic reaction cell (DRC) was used for the determination of Ca and P in foodstuffs. In this study, two different reaction gases, CH₄ and O₂, were introduced successively through the different channels to alleviate different interferences in the same analysis run. The effect of the operating conditions of the DRC system was studied to get the best signal-to-noise ratio for each element. The interfering ⁴⁰Ar⁺ at m/z 40 was reduced in intensity by up to five orders of magnitude by using 1.0 mL min^–1 CH₄ as reaction cell gas in the DRC. On the other hand, by using O₂ as the reaction gas, ³¹P⁺ was converted to ³¹P¹⁶O⁺ that could be detected at m/z 47 where there was less interference. The limits of detection for Ca and P were 0.2 ng mL^–1 and 0.3 ng mL^–1, respectively. This method was used to determine the concentrations of Ca and P and the ratio of Ca to P in NIST SRM 1549 non-fat milk powder and NIST RM 8345 whole milk powder reference materials and an infant milk powder and an infant cereal-rice sample purchased locally. The results for the reference samples agreed satisfactorily with the reference values. The accuracy of the determination was better than 4.1 and 0.9% for Ca and P, respectively. The results for infant milk powder and infant cereal were also found to be in good agreement with the value on the bottle label. Precision (RSD) between sample replicates was better than 4.8% for all the determinations.     

Development of a new method for sulfide determination by vapor generator–inductively coupled plasma–mass spectrometry

A new sensitive methodology for the determination of total reduced sulfur species in natural waters and acid volatile sulfides in sediments at low levels (μg L^− 1) is described. Reduced sulfur species were separated from the water matrix in the form of H₂S after reaction with hydrochloric acid in a commercial vapor generator coupled to an inductively coupled plasma quadrupole mass spectrometer (VG–ICP–QMS) equipped with a reaction cell. The method avoided the effect of polyatomic isobaric interferences at m/z 32 caused by ¹⁶O¹⁶O⁺ and ¹⁴N¹⁸O⁺ through the elimination of the aqueous matrix, a source of oxygen. By introducing a mixture of helium and hydrogen gases into the octopole reaction cell, a series of ion-molecule reactions were induced to reduce the interfering polyatomic species. Operating conditions of the octopole reaction cell system and the analyzer were optimized to get the best signal to background ratio for ³²S; a full factorial 2³ experimental design was developed in order to evaluate which variables had a significant effect and a simplex methodology was applied to find the optimum conditions for the variables. The new method was evaluated by comparison to the standard potentiometric method. The analytical methodology developed was applied to the analysis of reduced sulfur species in natural waters and acid volatile sulfides in sea sediments.     

电感耦合等离子体质谱法测定花生中34种元素

建立了微波消解-碰撞/反应池(ORS)电感耦合等离子体质谱仪(ICP-MS)同时测定花生中的Na、Mg、Ca、Fe、Se、Mo和稀土元素等34种元素的分析方法。样品经微波消解后,在线加入内标元素45Sc、72Ge、103Rh、115In和209Bi消除基体效应,应用碰撞反应池技术,以4.5 mL/min流速的氦气作为碰撞反应气,有效消除多原子离子产生的质谱干扰。各元素的检出限为0.0003～17.37ng/mL,相对标准偏差(RSD)低于2.9%;标准物质的测定值均在标准值范围内,结果令人满意。该方法可用于花生中多种元素的同时测定。     

Determination of arsenic, iron and selenium in moss samples using hexapole collision cell, inductively coupled plasma-mass spectrometry

Different collision gases (H₂, He and premixed 7% H₂ in He) used in the hexapole collision cell of an inductively coupled plasma-mass spectrometer (ICP-MS) were compared, and the gas-flow rates were optimized for the determination of arsenic (), iron () and selenium (). The study showed that the argon-based interferences at mass-to-charge ratios (m/z) of 56, 75 and 80 can be overcome by the optimized gas flows (7.5 ml min⁻¹ premixed 7% H₂ in He and 2 ml min⁻¹ H₂) in the hexapole collision cell. Detection limits of 15.5 ng l⁻¹ for iron () and 29 ng l⁻¹ for selenium () in 2% (v/v) HNO₃ were obtained under optimized collision cell conditions. The detection limit for arsenic () obtained in difficult hydrochloride acid matrix (5% HCl (v/v)) was 153 ng l⁻¹. The accuracy of the optimized method was confirmed by analyzing two moss reference materials. The results obtained by ICP-MS for arsenic, selenium and iron from both moss reference samples were, in most cases, in good agreement with the certified values.     

Determination of calcium, iron and zinc in milk powder by reaction cell inductively coupled plasma mass spectrometry

An inductively coupled plasma mass spectrometer (ICP-MS) equipped with a dynamic reaction cell™ (DRC) was used for the determination of Ca, Fe and Zn in milk powder samples. The effect of the operating conditions of the DRC system was studied to get the best signal-to-noise (S/N) ratio. The potentially interfering ⁴⁰Ar⁺, ⁴⁰Ar¹⁶O⁺, ⁴⁰Ca¹⁶O⁺, ⁴⁸Ca¹⁶O⁺ and ³²S¹⁶O¹⁶O⁺ at the masses m/z 40, 56 and 64 were reduced in intensity significantly by using CH₄ as the reaction cell gas in the DRC while a q-value of 0.7 was used. The limits of detection for ⁴⁰Ca, ⁵⁶Fe and ⁶⁴Zn estimated from the external calibration graphs were 1, 0.01 and 0.001 ng ml⁻¹, respectively, which correspond to 1000, 10 and 1 ng g⁻¹ in the original powder sample. This method was applied to the determination of Ca, Fe and Zn in NIST SRM 1549 non-fat milk powder and two milk powder samples purchased locally. The results for the reference sample agreed satisfactorily with the reference values; the accuracy of the determination was better than 3.8, 18 and 2.2% for Ca, Fe and Zn, respectively. The results for which no reference value was available were also found to be in good agreement between different isotopes. Precision (R.S.D.) between sample replicates was better than 10% for all the determinations.     

Microwave assisted volatilization of silicon as fluoride for the trace impurity determination in silicon nitride by dynamic reaction cell inductively coupled plasma-mass spectrometry

A low pressure microwave assisted vapor phase dissolution procedure for silicon nitride and volatilization of in situ generated SiF₄ has been developed using H₂SO₄, HF and HNO₃ for the determination of trace impurities present in silicon nitride. Sample was taken in minimum amount (0.5 mL for 100 mg) of H₂SO₄ and treated with vapors generated from HF and HNO₃ mixture in presence of microwaves in a closed container. An 80 psi pressure with ramp and hold times of 30 min and 60 min respectively, operated twice, resulted in 99.9% volatilization of Si. Matrix free solutions were analyzed for impurities using DRC-ICP-MS. The recoveries of Cr, Mn, Fe, Ni, Co, Cu, Zn, Sr, Y, Cd, Ba and Pb were between 80 and 100% after volatilization of Si. The blanks were in lower ng g⁻¹ with method detection limits in lower ng g⁻¹ to sub ng g⁻¹ range. The method was applied for the analysis of two silicon nitride samples.     

Use of enzymatic hydrolysis for the multi-element determination in mussel soft tissue by inductively coupled plasma-atomic emission spectrometry

A systematic evaluation of different variables affecting the enzymatic hydrolysis of mussel soft tissue by five enzymes, three proteases (pepsin, pancreatin and trypsin), lipase and amylase, has been carried out for the determination of trace elements (As, Al, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) by inductively coupled plasma-atomic emission spectrometry (ICP-AES). Enzymatic hydrolysis methods offers advantages such as a less species alteration, safer laboratory conditions and a less contaminant wastes. The enzymatic hydrolysis was performed in an incubation camera Boxcult with orbital and horizontal shaker. Variables affecting the enzymatic hydrolysis process were simultaneously studied by applying a Plackett-Burman design (PBD). For a confidence interval of 95%, the significant factors for all enzymes and for most of the elements were the pH, the incubation temperature and the ionic strength. These significant factors were optimized later by using a central composite design (CCD), which gave optimum conditions at pH of 1, incubation temperature of 37 °C and ionic strength fixed by sodium chloride at 0.2 M when using pepsin. For pancreatin, trypsin, lipase and amylase there were found two different optimum condition sets. The first one involves the use of a 0.5 M phosphate buffer (ionic strength), at a pH of 6 and at an incubation temperature of 37 °C, which allows the quantitative extraction of Al, Cr, Mn, Pb and Zn. The second conditions set employees a 0.1 M phosphate buffer (ionic strength), a pH of 9 and an incubation temperature at 37 °C, and it results adequate to extract As, Cd, Cu, Fe and Ni. Analytical performances, repeatability of the over-all procedure and accuracy, by analyzing DORM-1, DORM-2 and TORT-1 certified reference materials, were finally assessed for each enzyme. Good agreement with certified values has been assessed for most of the elements (As, Cd, Cr, Cu, Mn, Ni, Pb and Zn) when using trypsin, pepsin and/or pancreatin, except for Cd and Pb in DORM-1 and DORM-2 because of the certified contents in such certified reference materials are lower than the limit of detection (0.10 and 0.16 μg g⁻¹ for Cd and Pb, respectively, for the use of trypsin).     

雾室温度对ICP-MS分析性能影响的研究

研究了在电感耦合等离子体质谱分析中雾室温度对仪器分析性能的影响情况。在实验中选取半导体对雾室进行制冷,结果表明随着半导体制冷温度升高,进入等离子体水蒸气和分析元素气溶胶的量增加,但水蒸气引入量的增加幅度明显大于气溶胶,温度每增加1℃,等离子体中水的负载量增加2 3%,而气溶胶则只增加0.35%。同时随着半导体制冷温度的升高,分析元素的灵敏度下降,氧化物干扰增强,但氧化物的计数并未增加。根据元素灵敏度和氧化物干扰随半导体制冷温度变化的差异性,对人工模拟高纯Sm2O3中杂质稀土元素Dy、Ho、Er、Yb的量进行了计算,通过与模拟加入量比较,证明使用这种方法可对高纯稀土中某些受基体元素氧化物离子严重干扰的稀土元素进行快速定量分析,分析结果的偏差小于20%。     

Determination of tin in soil by continuous hydride generation and inductively coupled plasma mass spectrometry

A method was investigated for the determination of Sn in soil samples by KOH fusion followed by continuous hydride generation coupled with inductively coupled plasma mass spectrometry (HG-ICP-MS). Sample solutions in 3.0 M HCl were mixed in line with a solution of 2.4% NaBH₄ and 0.25 M KOH to generate stannane gas. The mixture was delivered continuously to a gas/liquid separator and the stannane gas was introduced into a Perkin-Elmer Sciex Elan 6000 ICP-MS for concentration measurements. A method detection limit of 0.45 mg/kg was sufficient for Sn levels commonly found in soil samples. Sn concentrations as low as 2.5 mg/kg were reproducibly measured in soil samples. Sample results by HG-ICP-MS agreed within ±17% relative difference to results by instrumental neutron activation analysis (INAA) and within ±6% relative difference to results by KOH fusion followed by inductively coupled plasma optical emission spectroscopy (ICP-OES).     

Microwave assisted extraction of iodine and bromine from edible seaweed for inductively coupled plasma-mass spectrometry determination

The feasibility of microwave energy to assist the solubilisation of edible seaweed samples by tetramethylammonium hydroxide (TMAH) has been investigated to extract iodine and bromine. Inductively coupled plasma-mass spectrometry (ICP-MS) has been used as a multi-element detector. Variables affecting the microwave assisted extraction/solubilisation (temperature, TMAH volume, ramp time and hold time) were firstly screened by applying a fractional factorial design (2^5-1 + 2), resolution V and 2 centre points. When extracting both halogens, results showed statistical significance (confidence interval of 95%) for TMAH volume and temperature, and also for the two order interaction between both variables. Therefore, these two variables were finally optimized by a 2² + star orthogonal central composite design with 5 centre points and 2 replicates, and optimum values of 200 °C and 10 mL for temperature and TMAH volume, respectively, were found. The extraction time (ramp and hold times) was found statistically non-significant, and values of 10 and 5 min were chosen for the ramp time and the hold time, respectively. This means a fast microwave heating cycle. Repeatability of the over-all procedure has been found to be 6% for both elements, while iodine and bromine concentrations of 24.6 and 19.9 ng g⁻¹, respectively, were established for the limit of detection. Accuracy of the method was assessed by analyzing the NIES-09 (Sargasso, Sargassum fulvellum) certified reference material (CRM) and the iodine and bromine concentrations found have been in good agreement with the indicative values for this CRM. Finally, the method was applied to several edible dried and canned seaweed samples.     

Bromine determination in polymers by inductively coupled plasma-mass spectrometry and its potential for fast first screening of brominated flame retardants in polymers and paintings

The impact of brominated flame retardants (BFRs) on the environment and their potential risk in animal and human health is a present concern. Therefore, existing legislation in the European Union demands that polymers with BFRs are identified and eliminated from the recycling process due to their potential health hazard.In this work, a flow-injection (FI) system coupled to inductively coupled plasma-mass spectrometry (ICP-MS) was optimized for the detection of traces of bromine in polymers, plastic paints and enamels containing BFRs. Sample preparation requires a microwave-assisted digestion in order to transfer bromine in polymeric samples to solution. After appropriate optimization of the digestion procedure and the ICP-MS detection, a detection limit (DL) of 4.2 mg kg⁻¹ was obtained for synthesized polyurethane standards containing known concentrations of bromine. The precision of the proposed method, evaluated as the R.S.D. of signals obtained for three replicates of polymeric standard BFRs at the normative EU level, was as low as 3.6%.This simple developed methodology was characterized for the screening of bromine in polymeric matrices. The proposed system provides rapid binary yes/no overall responses, being appropriate for the screening of bromine above a pre-set concentration threshold. The unreliability region (UR), given by the probability of false positives and false negatives (set at 5% in both cases), was in the range between 442 and 678 mg kg⁻¹ of bromine (at a cut-off level of 0.1% in BFRs by weight of homogeneous material fixed by the EU normative). Finally, the applicability of the proposed screening system was tested for the reliable control of bromine in different commercial samples including flame-retardant paints and enamels.     

Comparison of standard and reaction cell inductively coupled plasma mass spectrometry in the determination of chromium and selenium species by HPLC-ICP-MS

Elemental speciation is becoming a common analytical procedure for geochemical investigations. The various redox species of environmentally relevant metals can have vastly different biogeochemical properties, including sorption, solubility, bioavailability, and toxicity. The use of high performance liquid chromatography (HPLC) coupled to elemental specific detectors, such as inductively coupled plasma mass spectrometry (ICP-MS), has become one of the most important speciation methods employed. This is due to the separation versatility of HPLC and the sensitive and selective detection capabilities of ICP-MS. The current study compares standard mode ICP-MS to recently developed reaction cell (RC) ICP-MS, which has the ability to remove or reduce many common polyatomic interferences that can limit the ability of ICP-MS to quantitate certain analytes in complex matrices. Determination of chromium and selenium redox species is achieved using ion-exchange chromatography with elemental detection by standard and RC-ICP-MS, using various chromium and selenium isotopes. In this study, method performance and detection limits for the various permutations of the method (isotope monitored or ICP-MS detection mode) were found to be comparable and generally less than 1 μg L⁻¹. The method was tested on synthetic laboratory samples, surface water, groundwater, and municipal tap water matrices.     

A high-throughput solid-phase extraction microchip combined with inductively coupled plasma-mass spectrometry for rapid determination of trace heavy metals in natural water

Herein, a hyphenated system combining a high-throughput solid-phase extraction (htSPE) microchip with inductively coupled plasma-mass spectrometry (ICP-MS) for rapid determination of trace heavy metals was developed. Rather than performing multiple analyses in parallel for the enhancement of analytical throughput, we improved the processing speed for individual samples by increasing the operation flow rate during SPE procedures. To this end, an innovative device combining a micromixer and a multi-channeled extraction unit was designed. Furthermore, a programmable valve manifold was used to interface the developed microchip and ICP-MS instrumentation in order to fully automate the system, leading to a dramatic reduction in operation time and human error. Under the optimized operation conditions for the established system, detection limits of 1.64–42.54 ng L⁻¹ for the analyte ions were achieved. Validation procedures demonstrated that the developed method could be satisfactorily applied to the determination of trace heavy metals in natural water. Each analysis could be readily accomplished within just 186 s using the established system. This represents, to the best of our knowledge, an unprecedented speed for the analysis of trace heavy metal ions.     

Selenium speciation analysis in a sediment using strong anion exchange and reversed phase chromatography coupled with inductively coupled plasma-mass spectrometry

An analytical procedure for selenium speciation of analysis of selenourea (SeU), selenoethionine (SeE), selenomethionine (SeM), Se(VI), Se(IV), dimethylselenide (dMeSe) and dimethyldiselenide (dMedSe) was developed, based on two complementary liquid chromatography (LC) techniques coupled with inductively coupled plasma-mass spectrometry (ICP-MS). Specifically, strong anion exchange (SAX) chromatography coupled with ICP-MS was used for the separation and quantification of all the earlier mentioned Se compounds, except for the two methyl selenides, which could be separated and determined by reversed phase chromatography coupled with ICP-MS. This procedure was applied to a soil sample from the warm springs area of Thermopyles (Greece). For leaching the Se species from the soil sample, four extraction methods, using water at ambient temperature, hot water, methanol and 0.5 M HCl, were tested for their efficiency of extracting the different Se species. The speciation results obtained by the LC-ICP-MS methods were compared with those obtained by voltammetric techniques. The determination of total selenium in the sample was achieved by graphite furnace atomic absorption spectrometry, as well as by ICP-atomic emission spectrometry, after suitable digestion of the sediment sample.     

Determination of chromium, iron and selenium in foodstuffs of animal origin by collision cell technology, inductively coupled plasma mass spectrometry (ICP-MS), after closed vessel microwave digestion

The determination of chromium (⁵²Cr), iron (⁵⁶Fe) and selenium (⁸⁰Se) isotopes in foodstuffs of animal origin has been performed by collision cell technology (CCT) mode using an inductively coupled plasma mass spectrometry (ICP-MS) as detector after closed vessel microwave digestion. To significantly decrease the argon-based interferences at mass to charge ratios (m/z): 52 (⁴⁰Ar¹²C), 56 (⁴⁰Ar¹⁶O) and 80 (⁴⁰Ar⁴⁰Ar), the gas-flow rates of a helium and hydrogen mixture used in the hexapole collision cell were optimised to 1.5 ml min⁻¹ H₂ and 0.5 ml min⁻¹ He and the quadrupole bias was adjusted daily between −2 and −15 mV. Limits of quantification (LOQ) of 0.025, 0.086 and 0.041 mg kg⁻¹ for Cr, Fe and Se, respectively, in 6% HNO₃ were estimated under optimized CCT conditions. These LOQ were improved by a factor of approximately 10 for each element compared to standard mode.Precision under repeatability, intermediate precision reproducibility and trueness have been tested on nine different certified reference materials in foodstuffs of animal origin and on an external proficiency testing scheme. The results obtained for chromium, iron and selenium were in all cases in good agreement with the certified values and trueness was improved, compared to those obtained in standard mode.     

Dry ashing of organic rich matrices with palladium for the determination of arsenic using inductively coupled plasma-mass spectrometry

A dry ashing procedure is developed for the determination of As in organic rich matrices such as wheat flour, lichen and tobacco leaves. The volatility of As during dry ashing is avoided by the addition of palladium nitrate [Pd(NO₃)₂]. The recovery of both As(III) and As(V) is found to be near quantitative. The residue after dry ashing is dissolved in nitric acid (HNO₃) and analysed by inductively coupled plasma-mass spectrometry (ICP-MS). The process blank and limit of detection (LOD) are 11 and 6.6 ng g⁻¹, respectively. The procedure is applied for the determination of As in certified reference materials namely wheat flour NIST SRM 1567a (National Institute of Standards and Technology Standard Reference Material), lichen BCR CRM 482 (Institute for Reference Materials, European Commission) and Virginia tobacco leaves CTA-VTL-2 (Poland Academy of Sciences). The results obtained by the present procedure are in good agreement with the certified values and also determined after complete dissolution of samples using closed microwave digestion.     

电感耦合等离子质谱法测定染铅猪仔的血铅、尿铅含量

利用电感耦合等离子质谱法测定染铅猪仔的血铅、尿铅含量.铅元素校正曲线的相关系数达到0.9999,方法检出限为0.08 μg/L.用冻干牛血铅、镉成分分析标准物质和冻干人尿铅成分分析标准物质验证了方法的准确性和重复性,分析结果表明,测定值与标准值基本吻合,测定值的相对标准偏差＜3.4％.用此方法分析了染铅猪仔不同时段的血...     

On-line preconcentration and simultaneous determination of heavy metal ions by inductively coupled plasma-atomic emission spectrometry

A flow injection analysis system for on-line preconcentration and simultaneous determination of Bi³⁺, Cd²⁺, Co²⁺, Cu²⁺, Fe³⁺, Ni²⁺, Pb²⁺ and Zn²⁺ in aqueous samples by inductively coupled plasma (ICP)-atomic emission spectrometry with a charge coupled detector is described. The preconcentration of analytes is accomplished by retention of their chelates with sodium diethyldithiocarbamate in aqueous solution on a solid phase containing octadecyl silica in a minicolumn. Methanol, as eluent, is introduced into the conventional nebulizer of the ICP instrument. The effects of different parameters, including preconcentration flow rate (equal to sample flow rate (SR)), eluent flow rate (ER), weight of solid phase (W) and eluent loop volume (EV), were optimized by the super-modified simplex method. The optimum conditions were evaluated to be SR 7.2 ml min⁻¹, ER 3.5 ml min⁻¹, W of 100 mg and EV of 0.8 ml. An enrichment factor of 312.5 for each analyte was obtained. The detection limits of the proposed method for Bi³⁺, Cd²⁺, Co²⁺, Cu²⁺, Fe³⁺, Ni²⁺, Pb²⁺ and Zn²⁺ were evaluated as 1.3, 1.0, 0.8, 0.3, 14.7, 0.5, 5.5 and 0.1 ng l⁻¹, respectively. The effect of several metal ions on percent recovery was also studied. The method was applied to the recovery of these heavy metals from real matrices and to the simultaneous determination of these cations in different water samples.