Flow injection spectrofluorimetric determination of iron(III) in water using salicylic acid

A simple and fast flow injection fluorescence quenching method for the determination of iron in water has been developed. Fluorimetric determination is based on the measurement of the quenching effect of iron on salicylic acid fluorescence. An emission peak of salicylic acid in aqueous solution occurs at 409 nm with excitation at 299 nm. The carrier solution used was 2 × 10⁻⁶ mol L⁻¹ salicylic acid in 0.1 mol L⁻¹ NH₄⁺/NH₃ buffer solution at pH 8.5. Linear calibration was obtained for 5–100 μg L⁻¹ iron(III) and the relative standard deviation was 1.25 % (n = 5) for a 20 μL injection volume iron(III). The limit of detection was 0.3 μg L⁻¹ and the sampling rate was 60 h⁻¹. The effect of interferences from various metals and anions commonly present in water was also studied. The method was successfully applied to the determination of low levels of iron in real samples (river, sea, and spring waters).     

Determination of lead in wine by hydride generation atomic fluorescence spectrometry in the presence of hexacyanoferrate(III)

A rapid, accurate, and precise method is described for the determination of Pb in wine using continuous-flow hydride generation atomic fluorescence spectrometry (CF-HGAFS). Sample pretreatment consists of ten-fold dilution of wine followed by direct plumbane generation in the presence of 0.1 mol L⁻¹ HCl and 1% m/v K₃[Fe(CN)₆] with 1% m/v NaBH₄ as reducing agent. An aqueous standard calibration curve is recommended for Pb quantification in wine sample. The method provides a limit of detection and a limit of quantification of 0.3 μg L⁻¹ and 1 μg L⁻¹, respectively. The relative standard deviation varies between 2–6% (within-run) and 4–11% (between-run) at 3–30 μg L⁻¹ Pb levels in wine. Good agreement has been demonstrated between results obtained by CF-HGAFS and direct electrothermal atomic absorption spectrometry in analyses of red and white wines within the concentration range of 9.2–25.8 μg L⁻¹ Pb.     

A novel kinetic-spectrophotometric method for determination of nitrites in water

A simple, selective and sensitive kinetic method for the determination of nitrite in water was developed. The method is based on the catalytic effect of nitrite on the oxidation of methylene blue (MB) with bromate in a sulfuric acid medium. During the oxidation process, absorbance of the reaction mixture decreases with the increasing time, inversely proportional to the nitrite concentration. The reaction rate was monitored spectrophotometrically at λ = 666 nm within 30 s of mixing. Linear calibration graph was obtained in the range of 0.005–0.5 μg mL⁻¹ with a relative standard deviation of 2.09 % for six measurements at 0.5 μg mL⁻¹. The detection limit was found to be 0.0015 μg mL⁻¹. The effect of different factors such as acidity, time, bromate concentration, MB concentration, ionic strength, and order of reactants additions is reported. Interference of the most common foreign ions was also investigated. The optimum experimental conditions were: 0.38 mol L⁻¹ H₂SO₄, 5 × 10.4 mol L⁻¹ KBrO₃, 1.25 × 10.5 mol L⁻¹ MB, 0.3 mol L⁻¹ sodium nitrate, and 25°C. The proposed method was conveniently applied for the determination of nitrite in spiked drinking water samples.     

Determination of Trihalomethanes in Drinking Water by Dispersive Liquid–Liquid Microextraction then Gas Chromatography with Electron-Capture Detection

Dispersive liquid–liquid microextraction (DLLME) has been used for preconcentration of trihalomethanes (THMs) in drinking water. In DLLME an appropriate mixture of an extraction solvent (20.0 μL carbon disulfide) and a disperser solvent (0.50 mL acetone) was used to form a cloudy solution from a 5.00-mL aqueous sample containing the analytes. After phase separation by centrifugation the enriched analytes in the settled phase (6.5 ± 0.3 μL) were determined by gas chromatography with electron-capture detection (GC–ECD). Different experimental conditions, for example type and volume of extraction solvent, type and volume of disperser solvent, extraction time, and use of salt, were investigated. After optimization of the conditions the enrichment factor ranged from 116 to 355 and the limit of detection from 0.005 to 0.040 μg L⁻¹. The linear range was 0.01–50 μg L⁻¹ (more than three orders of magnitude). Relative standard deviations (RSDs) for 2.00 μg L⁻¹ THMs in water, with internal standard, were in the range 1.3–5.9% (n = 5); without internal standard they were in the range 3.7–8.6% (n = 5). The method was successfully used for extraction and determination of THMs in drinking water. The results showed that total concentrations of THMs in drinking water from two areas of Tehran, Iran, were approximately 10.9 and 14.1 μg L⁻¹. Relative recoveries from samples of drinking water spiked at levels of 2.00 and 5.00 μg L⁻¹ were 95.0–107.8 and 92.2–100.9%, respectively. Comparison of this method with other methods indicates DLLME is a very simple and rapid (less than 2 min) method which requires a small volume of sample (5 mL).     

A Capillary GC Method Using Nitrogen Phosphorus Detection for Determination of Topiramate in Patients with Epilepsy

A new capillary gas chromatographic assay with nitrogen phosphorus detection for the determination of topiramate in the serum was developed and validated. The sample procedure included a liquid–liquid extraction of 0.1 mL of alkalized sample with ethyl acetate. The organic solvent was evaporated, and flash methylation of topiramate and internal standard 5-(p-methylphenyl)-5-phenylhydantoin with trimethylanilinium hydroxide (0.07 mol L⁻¹ in methanol) was performed. The structure of derivatization product was confirmed using gas chromatography–mass spectrometry. Validation experiments certified suitability of bioanalytical method in the monitoring of serum concentrations in epileptic patients. The limit of detection was found to be 1.69 μmol L⁻¹. The range of applicability and linearity was established from 4.35 to 69.62 μmol L⁻¹. The accuracy and precision reached acceptable values from 86.15 to 109.5% (recovery) respectively, values were from 2.19 to 11.03% (RSD). No interference was found from endogenous substances or studied antiepileptic drugs.     

Analysis of urine for cysteine, cysteinylglycine, and homocysteine by high-performance liquid chromatography

A new analytical method is proposed for simultaneous determination, by liquid chromatography, of the three main urinary thiols–cysteine, cysteinylglycine, and homocysteine. To measure the total amount of these thiols urine is reduced with sodium borohydride, to convert disulfides to thiols which are then derivatized with 2-chloro-1-methylquinolinium tetrafluoroborate. Separation and quantitation of the 2-S-quinolinium thiol derivatives formed were achieved by high-performance liquid chromatography with detection at 355 nm. Validation showed the method enabled reliable simultaneous determination of these aminothiols in urine. The calibration graphs for each analyte, obtained by use of normal urine spiked with increasing amounts of cysteine, cysteinylglycine, and homocysteine, were linear (R ²≥0.997) over the range covering most practical situations. The recovery of the assay was 98–100% and sensitivity was 0.12–0.25 μmol L⁻¹. The method was applied to 91 different samples of normal urine to establish reference values for the aminothiols, normalized on creatinine.     

Development of a novel luminol chemiluminescent method catalyzed by gold nanoparticles for determination of estrogens

It has been found that gold nanoparticles (nano-Au) enhance the chemiluminescence (CL) of the luminol–hydrogen peroxide system and that estrogens inhibit these CL signals in alkaline solution. CL spectra, UV–visible spectra, X-ray photoelectron spectra (XPS), and transmission electron microscopy (TEM) were used to investigate the mechanism of the CL enhancement. On the basis of the inhibition, a flow-injection CL method has been established for determination of three natural estrogens. Under the optimized conditions, the linear range for determination of the estrogens was 0.07 to 7.0 μmol L⁻¹ for estrone, 0.04 to 10 μmol L⁻¹ for estradiol, and 0.1 to 10 μmol L⁻¹ for estriol. The detection limits were 3.2 nmol L⁻¹ for estrone, 7.7 nmol L⁻¹ for estradiol, and 49 nmol L⁻¹ for estriol, with RSD of 2.9, 2.6, and 1.8%, respectively. This method has been used for analysis of estrogens in commercial tablets and in urine samples from pregnant women.     

Analysis of Terbumeton and its Major Metabolites by SPE and DAD-HPLC in Soil Bulk Water

A rapid and inexpensive method for simultaneous quantification of terbumeton (TER), and its major potential metabolites (TED; terbumeton-desethyl, TOH; terbumeton-2-hydroxy and TID; terbumeton-deisopropyl) in soil bulk water (SBW) samples is proposed. The analytical method involves extraction–concentration from SBW samples using a graphitized carbon black (GCB) cartridge followed by their separation–detection by reversed-phase high-performance liquid chromatography analysis using a C₁₈ column and a diode array detector. A mobile phase of acetonitrile−0.005 mol L⁻¹ phosphate buffer (pH 7.0) (35:65, v/v) at a flow rate of 0.8 mL min⁻¹ in isocratic elution mode has been used. After optimization of the extraction and separation conditions, this method can be used for the simultaneous determination of investigated compounds in the range of the international limits of 0.1 μg L⁻¹. For TER the detection limit was 0.009 μg L⁻¹ and it was 0.100, 0.550, and 0.480 μg L⁻¹ for TED, TOH, and TID, respectively. The recoveries of TER, TED, TOH, and TID from SBW samples, measured at three levels of concentration range, were found to be between 48.0 and 102.0%. The intra-day precision measured by relative standard deviation (RSD) was always lower than 9.0%.     

Determination of vitamin B<Subscript>1</Subscript> in seawater and microalgal fermentation media by high-performance liquid chromatography with fluorescence detection

A highly sensitive high-performance liquid chromatographic method with fluorescence detection has been developed for determination of vitamin B₁. Vitamin B₁ was converted into a fluorescent compound by treatment with hydrogen peroxide–horseradish peroxidase and the derivative was subsequently analyzed by HPLC on a Waters Spherisorb ODS2 column (250 mm×4.6 mm ID, 5 μm) with 40:60 methanol–pH 8.5 acetate buffer solution as mobile phase and fluorescence detection at 440 nm (with excitation at 375 nm). The calibration graph was linear from 5.00×10⁻¹⁰ mol L⁻¹ to 5.00×10⁻⁷ mol L⁻¹ for vitamin B₁ with a correlation coefficient of 0.9991 (n=9). The detection limit was 1.0×10⁻¹⁰ mol L⁻¹. The method was successfully used for determination of vitamin B₁ at pg mL⁻¹ levels in microalgal fermentation media and seawater after solid-phase extraction. Recovery was from 89 to 110% and the relative standard deviation was in the range 1.1 to 4.3%.     

Development of a sequential injection anodic stripping voltammetry (SI-ASV) method for determination of Cd(II), Pb(II) and Cu(II) in wastewater samples from coatings industry

This paper describes the development and validation of a sequential injection (SI) anodic stripping voltammetry (ASV) method using the hanging mercury drop electrode for accumulation of the heavy metal cations Cu(II), Pb(II) and Cd(II). The method was applied to wastewater samples after proper acid digestion in open vessels to eliminate matrix effects. For a deposition time of 90 s at the flow rate of 10 μl s⁻¹, the detection limits of the method were 0.06, 0.09 and 0.16 μmol L⁻¹ for Cd, Pb and Cu, respectively. Under these conditions the linear dynamic range was between 0.20 and 9.0 μmol L⁻¹ and the sampling frequency was 30 analyses per hour. The relative standard deviation of the method was 3%(n=7) at the concentration level of 2.0 μmol L⁻¹. The accuracy of the method was evaluated by spiking the samples with known amounts of the metal cations, and by comparison with an independent analytical technique, the inductively coupled plasma atomic emission spectroscopy (ICP-AES). Average recoveries were around of 84%, and the results showed no evidence of systematic errors in comparison to the ICP-AES.     

Determination of chromium in whole blood by DRC–ICP–MS: spectral and non-spectral interferences

Quantification of chromium in whole blood has been performed by ICP–quadrupole MS. The spectrometer was equipped with a dynamic reaction cell (DRC) with ammonia as reaction gas. The rejection parameter q (RPq) of the DRC and the flow rate of ammonia (NH₃) were optimized and set at 0.7 and 0.6 mL min⁻¹, respectively. Blood was diluted 1:51 (v/v) with an aqueous solution containing 0.1 mg L⁻¹ NH₄OH, 0.1 g L⁻¹ EDTA, 5 mg L⁻¹ n-butanol, and 0.1‰ Triton X100. Non-spectral matrix effects observed when using the DRC were confirmed by use of vanadium. External calibration with blank and standard solutions prepared in purified water led to biased results for quality control samples. Standard addition calibration was therefore used and its validity verified. By comparing the slopes and calculating residues, it was proved that the plot obtained with standard additions and the plot obtained from blood samples of different concentrations were aligned down to 0.05 μg L⁻¹ after dilution.     

Determination of glyphosate and AMPA in surface and waste water using high-performance ion chromatography coupled to inductively coupled plasma dynamic reaction cell mass spectrometry (HPIC–ICP–DRC–MS)

A novel method employing high-performance cation chromatography in combination with inductively coupled plasma dynamic reaction cell mass spectrometry (ICP–DRC–MS) for the simultaneous determination of the herbicide glyphosate (N-phosphonomethylglycine) and its main metabolite aminomethyl phosphonic acid (AMPA) is presented. P was measured as ³¹P¹⁶O⁺ using oxygen as reaction gas. For monitoring the stringent target value of 0.1 μg L⁻¹ for glyphosate, applicable for drinking and surface water within the EU, a two-step enrichment procedure employing Chelex 100 and AG1-X8 resins was applied prior to HPIC–ICP–MS analysis. The presented approach was validated for surface water, revealing concentrations of 0.67 μg L⁻¹ glyphosate and 2.8 μg L⁻¹ AMPA in selected Austrian river water samples. Moreover, investigations at three waste water-treatment plants showed that elimination of the compounds at the present concentration levels was not straightforward. On the contrary, all investigated plant effluents showed significant amounts of both compounds. Concentration levels ranged from 0.5–2 μg L⁻¹ and 4–14 μg L⁻¹ for glyphosate and AMPA, respectively.     

Simple and rapid determination of piperacillin and ceftazidime in human plasma samples by HPLC

Summary A simple and rapid liquid chromatographic method has been developed for the determination of therapeutic levels of piperacillin (I) and ceftazidime (II) in human plasma. Plasma and p-propionamidophenol (internal standard) were precipitated with methanol (I) or 20% trichloroacetic acid (II). The supernatant was analysed on a 5 μm Spherisorb ODS C₁₈ column with acetonitrile-0.05 M phosphate buffer pH 3.8 as mobile phase and ultraviolet detection at 254 nm. The calibration graph was linear from 10 to 250 μg mL⁻¹, for (I), and from 5 to 200 μg mL⁻¹ for (II). Intra and inter-day CV did no exceed 2.29% for (I), and were 10.76–11.13%–2.00–5.62 for (II) at concentrations of 10 μg mL⁻¹ and 250 μg mL⁻¹.     

LC Determination of Propylene Glycol in Human Plasma After Pre-Column Derivatization with Benzoyl Chloride

A simple high-performance liquid chromatographic method, using photodiode array detection was developed for the determination of propylene glycol in human plasma and in the fluid retreived after continuous veno-venous hemofiltration. The method entailed alkaline derivatization with benzoyl chloride and ethylene glycol as internal standard. The separation of the compounds, after extraction with pentane, was carried out on a Pursuit C8 column with UV-detection at 230 nm. Validation samples were analyzed with an accuracy between 95 and 105%, and intra- and inter-day coefficients of variation of less than 8%. The calibration curve was linear over a concentration range of 5–100 mg L⁻¹ with a detection limit of 1 mg L⁻¹. Blood plasma samples of several patients were analysed by using the prescribed method with propylene glycol concentrations varying from 5 to 98 mg L⁻¹. Compared to previously described LC methods, this method is ten times more sensitive and thus suitable for use in pharmacokinetic studies of propylene glycol.     

Determination and Pharmacokinetic Study of 10-O-Dimethylaminoethylginkgolide B in Rat Plasma by LC–MS

To evaluate the pharmacokinetics of a novel analogue of ginkgolide B, 10-O-dimethylaminoethylginkgolide B (XQ-1) in rat plasma in pre-clinical studies, a sensitive and specific liquid chromatographic method with electrospray ionization mass spectrometry detection (LC–ESI–MS) was developed and validated. After a simple extraction with ethyl acetate, XQ-1 was analyzed on a Shim-pack C18 column with a mobile phase of a mixture of 1 μmol L⁻¹ ammonium acetate containing 0.02% formic acid and methanol (55:45, v/v) at a flowrate of 0.3 mL min⁻¹. Detection was performed in selected ion monitoring (SIM) mode using target ions at [M + H]⁺ m/z 496.05 for XQ-1 and m/z 432.10 for the internal standard (lafutidine). Linearity was established for the concentration range from 2 to 1,000 ng mL⁻¹ . The extraction recoveries ranged from 86.0 to 89.9% in plasma at concentrations of 5, 50, and 500 ng mL⁻¹. The lower limit of quantification was 2 ng mL⁻¹ with 100 μL plasma. The validated method was successfully applied to a pharmacokinetic study after intragastic administration of XQ-1 mesylate in rats at a dose of 20 mg kg⁻¹.     

Multi-component analysis of tetracyclines, sulfonamides and tylosin in swine manure by liquid chromatography–tandem mass spectrometry

A multi-component method focussing on thorough sample preparation has been developed for simultaneous analysis of swine manure for three classes of antibiotic—tetracyclines, sulfonamides, and tylosin. Liquid manure was initially freeze-dried and homogenised by pulverization before extraction by pressurised liquid extraction. The extraction was performed at 75°C and 2,500 psig in three steps using two cycles with 0.2 mol L⁻¹ citric acid buffer (pH 4.7) and one cycle with a mixture of 80% methanol with 0.2 mol L⁻¹ citric acid (pH 3). After liquid–liquid extraction with heptane to remove lipids, the pH of the manure was adjusted to 3 with formic acid and the sample was vacuum-filtered through 0.6 μm glass-fibre filters. Finally the samples were pre-concentrated by tandem SPE (SAX-HLB). Recoveries were determined for manure samples spiked at three concentrations (50–5,000 μg kg⁻¹ dry matter); quantification was achieved by matrix-matched calibration. Recoveries were >70% except for oxytetracycline (42–54%), sulfadiazine (59–73%), and tylosin (9–35%) and did not vary with concentration or from day-to-day. Limits of quantification (LOQ) for all compounds, determined as a signal-to-noise ratio of 10, were in the range 10–100 μg kg⁻¹ dry matter. The suitability of the method was assessed by analysis of swine manure samples from six different pig-production sites, e.g. finishing pigs, sows, or mixed production. Residues of antibiotics were detected in all samples. The largest amounts were found for tetracyclines (up to 30 mg kg⁻¹ dry matter for the sum of CTC and ECTC). Sulfonamides were detected at concentrations up to 2 mg kg⁻¹ dry matter (SDZ); tylosin was not detected in any samples.      

Simultaneous analysis of three catecholamines by a kinetic procedure: comparison of prediction performance of several different multivariate calibrations

A rapid kinetic method for the simultaneous determination of levodopa, dopamine, and dobutamine was examined and developed. It was based on a consecutive reaction of a reduction of Cu(II) to Cu(I) by catecholamines, followed by the complexation of Cu(I) with neocuproine to form a yellow product in an acetic acid-acetate buffer. Spectrophotometric data were recorded at 453 nm (wavelength at the yellow complex absorption maximum) for 300 s. Linear calibrations were obtained in the concentration ranges of (0.08–1.44) × 10⁻⁵ mol L⁻¹, (0.08–1.44) × 10⁻⁵ mol L⁻¹, and (0.16–1.44) × 10⁻⁵ mol L⁻¹ for levodopa, dopamine, and dobutamine, respectively. A variety of multivariate calibration models was developed for simultaneous analysis of the three analytes; while most models produced satisfactory prediction results for synthetic samples, the hybrid linear analysis method was arguably the best-performing (relative prediction error, RPET = 6.6 %). The proposed method was applied to an analysis of spiked rabbit serum samples and the results showed good agreement with the high performance liquid chromatography measurements.     

Visual spectroscopy detection of triclosan

The azo coupling reaction with 2-aminonaphthalene-4,8-disulfonic acid (I) was used to develop a new cheap and rapid method of triclosan (II) determination in hygiene products. The calibration graph was linear in the range of 2.0−100 × 10⁻⁶ mol L⁻¹. The detection limit was 2.0 μmol L⁻¹.     

Simultaneous determination of MHD and DMD in dog plasma by high-performance liquid chromatography with fluorescence detection and its application to pharmacokinetic studies

A rapid, reproducible high-performance liquid chromatographic (HPLC) method with fluorescence detection for the simultaneous determination of 3(or 8)-(1-methoxyethyl)-8(or 3)-(1-hydroxyethyl)-deuteroporphyrin IX (MHD) and 3,8-di-(1-methoxyethyl)-deuteroporphyrin IX (DMD) in dog plasma was described. Fluorescein was used as an internal standard. A simple extraction step with ethyl acetate was performed before chromatography on a Diamonsil C₁₈ column (5 μm, 4.6 mm×150 mm). The chromatography used 0.02 mol L⁻¹ sodium acetate/tetrahydrofuran (66:34 v/v). The analytical curve was linear over the concentration range 0.025– 2.5 μg mL⁻¹. For a 100 μL dog plasma sample, the limit of determination for both MHD and DMD was 0.025 μg mL⁻¹. The recoveries of MHD and DMD were more than 76% and 89%, respectively. The intra-assay (within-run) and interassay (between-run) coefficients of variation (precisions) for MHD and DMD were less than 15%. This method was found to be suitable for the analysis of biosamples and was successfully applied to pharmacokinetic studies of Deuxemether in dogs.     

Determination of five nitrobenzoic acids in groundwater by solid-phase extraction and liquid chromatography–mass spectrometry

A method involving solid-phase extraction (SPE) and reversed-phase liquid chromatography–mass spectrometry (LC–MS) has been developed for determination, in groundwater, of nitrobenzoic acids associated with 2,4,6-trinitrotoluene production. Pre-concentration on a co-polymer-based SPE cartridge enabled quantitative extraction of the analytes from water. Investigation of negative ion electrospray and atmospheric-pressure chemical ionization mass spectrometry indicated the sensitivity of APCI was more than twice that of ESI. An ¹⁵N-labeled internal standard was used to achieve more accurate quantitation and mass assignment. Recovery was better than 80% when 10 mL water was extracted with the SPE cartridge. Combination of SPE with LC–MS analysis resulted in method detection limits of less than 5 μg L⁻¹. The method has been used for analysis of groundwater samples collected from a site of a former ammunition plant. Contamination with nitrobenzoic acids was determined at μg L⁻¹ levels.