UV辐照接枝制备酚酞基聚芳醚酮纳滤膜——链转移剂的作用

酚酞基聚芳醚酮(PEK-C)超滤膜的表面通过紫外辐照接枝丙烯酸(AA)可以制备对II价盐有很好截留率的亲水性纳滤膜. FTIR-ATR、表面接触角、SEM和AFM的研究结果表明, 在接枝单体溶液中加入异丙醇(i-PrOH)作为链转移剂并不影响AA在PEK-C超滤膜表面的接枝反应. 得到的改性膜同样具有优良的纳滤性能. 与不加i-PrOH的AA改性膜相比, 新合成的膜有较高的滤出液通量, 该膜对盐离子的截留率虽有所降低, 但可以通过增加接枝反应时间和辐照光源的强度来提高. i-PrOH的浓度对膜的分离性能的影响很大, 在低浓度时, 改性膜对离子的截留率会有所下降, 继续提高i-PrOH的浓度, 膜的截留率不再变化而滤出液通量会有成倍的增加, 表明链转移剂的存在可能会提高膜的接枝密度, 增加膜的表面电荷, 使膜对离子的截留率保持不变.     

Graft copolymerization kinetics of acrylic acid onto the poly(ethylene terephthalate) surface by atmospheric pressure plasma inducement

After one atmospheric pressure plasma treatment of poly(ethylene terephthalate) (PET) film, acrylic acid (AAc) in aqueous solution was successfully graft‐copolymerized onto PET films. The effects of reaction time, AAc monomer concentration and reaction temperature on grafting behavior of AAc were systematically studied. Possible reaction kinetics of plasma‐induced graft copolymerization, starting from initial hydroperoxide decomposition, were proposed. Through the Arrhenius analysis about graft copolymerization kinetics of AAc monomers on PET surface, it was revealed that the activation energies of decomposition, propagation and termination were 98.4, 63.5, and 17.5 kJ/mol, respectively. The temperature around 80 °C was favorable not only for the formation of oxide radicals through the thermal decomposition of hydroperoxide on PET surface but also for the extension of graft copolymer chain through direct polymer grafting. Poly(acrylic acid) (PAAc) grains grafted onto PET surfaces possessed relatively uniform size and both PAAc grain size and surface roughness increased with increasing the grafting degree of AAc. The increase of grain size with increasing grafting degree results from the possibility of forming long chain graft copolymers and their shielding of reactive sites. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1594–1601, 2008     

Electrochemical properties of PP membranes with plasma polymer coatings of acrylic acid

Commercial polypropylene (PP) membranes were modified by plasma polymerization coating of acrylic acid, in combination with oxygen flow or oxygen plasma etching. First, conditions for plasma polymerization coating were optimized in terms of the chemical resistance of the coatings and their ion exchange capacity as a function of plasma power, internal pressure and treatment time. Next, the plasma polymerization coating of acrylic acid was combined with oxygen flow or oxygen plasma etching, and their conditions were also optimized by measuring the ion exchange capacity. Finally, the modified membranes were subjected to electrical resistance and transport number measurements and characterized by -step, FT-IR/ATR and SEM. Among the modification methods, oxygen plasma etching followed by the plasma polymerization coating of acrylic acid provided the best electrochemical properties with 1.75 meq/g (IEC) and 112 Ω cm² (ER), 0.88 (TN).     

一种新型的亲水性聚丙烯酸-陶瓷复合膜

通过化学气相沉积和丙烯酸(AA)在大孔陶瓷膜表面的接枝共聚制备了一种新型的亲水性PAA-陶瓷复合膜. 用FT-IR、SEM、EDS、表面接触角等方法对复合膜接枝层的化学组成、表面形态、元素分布和亲水性进行了表征. 通过系统研究气相沉积和接枝反应的主要条件对膜的渗透汽化性能的影响, 发现当TEOS用量为5 mL, 汽化温度为175 ℃时进行气相沉积, 然后在丙烯酸浓度为7.5%的溶液中进行接枝聚合, 制得的复合膜对醇水混合物显示了优良的分离性能.     

RADICAL GRAFTING REACTIONS ONTO STARCH AND OTHER WATER-SOLUBLE COPOLYMERS IN ISOLATED GEL DROPLETS

A novel radical grafting copolymerization process has been designed for water-soluble polymers which avoids the problems of conducting grafting reactions in highly viscous polymerization media. A variety of water-soluble graft copolymers having starch or dextran as the backbone chain with grafted side chains of polyacrylamide (—AM—), poly (acrylic acid ) (—AA—), poly (acrylamide-co-acrylic acid) (—AM—NH_4AA—) or poly ( acrylamide-co-2-acryiamido-2-methyl-l-propanesulphinic acid) (—AM—AMPS—) have been synthesized in gel droplets using aceric sulphate redox initiator, and their properties compared. The reaction conditions were optimized taking into account reaction kinetic data and the observed properties of the products produced under different reaction conditions. The effects of the ratios of [backbone]/[graft monomer], [ AM]/[ AA]/[AMPS] , [Ce~(4+)]/[ S_2O_8=] and pH value on the reaction rate , conversion, grafting degree, grafted chain length and the product molecular weight have been investigated.     

TFC polyamide membranes modified by grafting of hydrophilic polymers: an FT-IR/AFM/TEM study

Surface modification using grafting of a hydrophilic polymer onto the membrane surface is a possible route to improving the fouling properties of polyamide thin-film composite membranes. The structure of nanofiltration (NF) and reverse osmosis (RO) membranes modified using graft polymerization of acrylic (AA) monomers was visualized and analyzed using attenuated total reflection–Fourier transform infrared spectroscopy, atomic force microscopy and transmission electron microscopy. The results show that a layer of AA polymer is indeed formed on the polyamide surface, which could be accompanied by a change of the surface morphology. It was observed that for the NF membranes studied polymerization could also take place inside the pores of the support as a result of penetration of the monomer through the active layer, particularly for high degrees of grafting. It suggests that the modification procedures should be optimized so that the latter effect is minimized.     

Preparation of Poly(ethylene terephthalate)‐g‐Methacrylamide Copolymers Initiated by Azobisizobutyronitrile: Characterization and Investigation of Some Properties

Poly(ethylene terephthalate)‐g‐methacrylamide (PET‐g‐MAAm) copolymer was prepared by graft copolymerization in organic solvent/water mixtures by using azobisizobutyronitrile (AIBN) as an initiator. The highest graft yield was obtained in 20/80 (v/v) acetonitrile/water mixture as 30.0%. The effect of polymerization parameters such as the ratio of solvent/water mixture, concentrations of initiator and monomer, temperature and time on the graft yield was studied. The moisture regain of the PET fiber increased with grafting from 0.42% to 3.01%. Thermogravimetric data showed that the thermal stability of PET fibers decreased with grafting and 85% of total weight of 29.7% grafted fiber was lost at 500°C. On the other hand, fiber density decreased with increasing graft yield. At SEM micrographs, the layers oriented in the direction of fiber length were observed on the surface of PET fiber as a result of grafting.     

两步辐射接枝法制备抗熔滴涤纶织物

以涤纶(PET)为基材,利用两步γ辐射接枝法在PET织物表面依次引发甲基丙烯酸缩水甘油酯(GMA)/二乙烯苯(DVB)和乙烯基磷酸二甲酯(DMVP)接枝共聚,制备了新型抗熔滴PET织物.接枝率随吸收剂量和单体浓度的增加而增加,随剂量率增加而下降.傅里叶红外(FTIR)、X射线光电子能谱(XPS)和热重分析(TGA)的分析结果表明在PET织物上成功引入目标接枝聚合物.相比PET织物,辐射改性PET织物的拉伸强度以及断裂伸长率均有所提高.通过引入交联网状结构以及促进成炭的含磷接枝聚合物,PET织物的抗熔滴特性得到了明显改善,燃烧过程中平均产生一滴熔滴的时间:PET为3.0 s/n,PET接枝PGMA/DVB后延长为17.0 s/n,而进一步接枝PDMVP后在整个燃烧过程中均不产生熔滴.这种新型的方法有望用于PET织物防护服抗熔滴性能的改善.     

Surface structures of fluoropolymer,polyolefin and polyester films after modification by graft polymerization

Pristine and argon plasma pretreated polytetrafluoroethylene (PTFE), polystyrene (PS), high-density polyethylene (HDPE) and poly(ethylene terrephthalate) (PET) films have been subjected to near-UV light-induced graft polymerization with water-soluble acrylamide (AAm), the sodium salt of styrene sulfonic acid (NaSS), acrylic acid (AAc) and N,N-dimethylaminoethylmethylacrylate (DMAEMA) monomers. The structure and composition at the substrate surface with grafted polymer were studied by angle-resolved X-ray photoelectron spectroscopy (XPS). In most cases, the density of surface grafting is enhanced by plasma pretreatment. For each polymer substrate with a substantial amount of grafting, the hydrophilic graft penetrates or becomes partially submerged beneath a thin surface layer of dense substrate chains. This stratified microstructure is consistent with the static secondary ion mass spectroscopy (SIMS) and Ar⁺ beam depth profiling results. The two latter techniques also suggest that when the grafted polymer has a bulky substituent, there is less efficient penetration of the grafted polymer below the surface.     

Patterned immobilization of biomolecules by using ion irradiation‐induced graft polymerization

A new method for biomolecular patterning based on ion irradiation‐induced graft polymerization was demonstrated in this study. Ion irradiation on a polymer surface resulted in the formation of active species, which was further used for surface‐initiated graft polymerization of acrylic acid. The results of the grafting study revealed that the surface graft polymerization using 20 vol % of acrylic acid on the poly(tetrafluoroethylene) (PTFE) film irradiated at the fluence of 1 × 10¹⁵ ions/cm² for 12 h was the optimum graft polymerization condition to achieve the maximum grafting degree. The results of the fluorescence microscopy also revealed that the optimum fluence to achieve the maximum fluorescence intensity was 1 × 10¹⁵ ions/cm². The grafting of acrylic acid on the PTFE surfaces was confirmed by a fluorescence labeling method. The grafted PTFE films were used for the immobilization of amine‐functionalized p‐DNA, followed by hybridization with fluorescently tagged c‐DNA. Biotin‐amine was also immobilized on the acrylic acid grafted PTFE surfaces. Successful biotin‐specific binding of streptavidin further confirmed the potential of this strategy for patterning of various biomolecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6124–6134, 2009     

Properties and evaluation of amidoxime-based UHMWPE fibrous adsorbent for extraction of uranium from seawater

An amidoxime-based ultra-high molecular weight polyethylene (UHMWPE) fibrous adsorbent was successfully prepared by γ-irradiation-induced graft copolymerization of acrylonitrile (AN) and acrylic acid (AA), followed by amidoximation. The grafting of AN and AA on the UHMWPE fiber and the amidoximation of the grafted fiber were confirmed by Fourier transform infrared spectroscopy, scanning electron microscopy, and thermogravimetric analysis. The mechanical property of the original and modified UHMWPE fibers was compared by single-filament strength test. The adsorption property of the UHMWPE fibrous adsorbent was evaluated by adsorption test in uranyl nitrate solution and seawater. The surface of the modified UHMWPE fibers was covered by the grafting layer and became rough. The tensile strength of the amidoxime-based UHMWPE fibrous adsorbent was influenced by the absorbed dose and hydrochloric acid elution, but was independent of the grafting yield and amidoximation. The uranium adsorption amount of the amidoxime-based UHMWPE fibrous adsorbent after immersing in seawater for 42 days was 2.3 mg-U/g.     

Radiation-Induced Asymmetric Grafting of Different Monomers into Base Films to Prepare Novel Bipolar Membranes

We prepared novel bipolar membranes (BPMs) consisting of cation and anion exchange layers (CEL and AEL) using radiation-induced asymmetric graft polymerization (RIAGP). In this technique, graft polymers containing cation and anion exchange groups were introduced into a base film from each side. To create a clear CEL/AEL boundary, grafting reactions were performed from each surface side using two graft monomer solutions, which are immiscible in each other. Sodium p-styrenesulfonate (SSS) and acrylic acid (AA) in water were co-grafted from one side of the base ethylene-co-tetrafluoroethylene film, and chloromethyl styrene (CMS) in xylene was simultaneously grafted from the other side, and then the CMS units were quaternized to afford a BPM. The distinct SSS + AA- and CMS-grafted layers were formed owing to the immiscibility of hydrophilic SSS + AA and hydrophobic CMS monomer solutions. This is the first BPM with a clear CEL/AEL boundary prepared by RIAGP. However, in this BPM, the CEL was considerably thinner than the AEL, which may be a problem in practical applications. Then, by using different starting times of the first SSS+AA and second CMS grafting reactions, the CEL and AEL thicknesses was found to be controlled in RIAGP.     

聚丙烯表面接枝改性络合金的研究

探索了一种通过聚丙烯(PP)改性来络合金金属的新途径.首先在PP膜上经紫外光引发实施丙烯酸的接枝聚合反应,得到表面带—COOH基团的改性PP膜;再用负离子开环聚合的方法在改性后的PP膜上接枝尼龙6.上述处理后的膜表面含有大量O、N的功能基团,故可将此膜用于对溶液中金的络合.利用ATR、SEM、XPS等技术对改性及络合进行了表征.实验结果表明,此方法制备的PP膜对金的络合效果明显.     

Radiation-induced grafting of diallyldimethylammonium chloride onto acrylic acid grafted polyethylene

Diallyldimethylammonium chloride (DADMAC) was grafted onto polyethylene (PE) films by a double grafting procedure. The PE film was initially modified by grafting acrylic acid (AA), through a mutual irradiation method. AA-g-PE film, thus obtained was subjected to subsequent radiation grafting reaction of DADMAC, to give a DADMAC-g-AA-g-PE film having a comb-type structure. The influence of different conditions, such as the extent of AA grafting, DADMAC concentration, absorbed dose and dose rate, on the grafting yield of DADMAC was investigated. A maximum DADMAC grafting of 30% was achieved. The equilibrium degree of swelling (EDS) of the grafted films were gravimetrically determined. TGA and FT-IR techniques were employed to characterize the grafted PE films.     

SURFACE MODIFICATION OF POLYPROPYLENE MICROFIBRE BY PLASMA-INDUCED VAPOR GRAFTING WITH ACRYLIC ACID

The hydrophilicity, dyeing and antistatic ability of polypropylene microfibre (PPMF) wereimproved by plasma-induced vapor grafting with acrylic acid. The effects of plasma discharge time, power,liquid phase acrylic acid temperature and environmental temperatore on grafting yield were investigated. Theexistence of grafted polyacrylic acid (PAA) was verified by ESCA and ATR FT-IR. The morphology ofgrafted PAA was directly observed by SEM. The wicking test shows that the hydrophilicity of modifiedPPMF is greatly enhanced. The dyeability test of modified PPMF was carried out using Dispersion Yellow. Itwas found that the dye uptake ratio is linear to the weight percent of grafting. The antistatic ability wasindicated by specific resistance. The specific resistance of modified PPMF was reduced to 10~6～10~7Ω·cm,thus the antistatic ability was considerably improved.     

一种利用梯度光掩模制备梯度表面的简便方法

以自制杂化双向拉伸聚丙烯/氧化硅(BOPP/SiOx)有机/无机杂化膜为基材,由喷墨打印机直接在杂化膜表面打印色阶图案,制备出对紫外光强度呈梯度透过的梯度光掩模;通过此掩模控制,在双向拉伸聚丙烯(BOPP)和聚对苯二甲酸乙二醇酯(PET)表面实施受限光催化氧化(CPO)光感应羟基化反应、受限光接枝丙烯酸(AA)以及表面...     

Covalently attached graft polymer monolayer on organic polymeric substrate via confined surface inhibition reaction

A grafting technique was proposed for the preparation of polymer monolayer on polymeric substrate. On the basis of our recent work on polymer‐supported inhibitor (PSI), hydroquinone (HQ) was first implanted onto polypropylene (PP) surface through UV‐initiated grafting. The resulting immobilized HQ was used as PSI for the thermal‐induced free radical polymerization (FRP) of acrylic acid (AA). The inhibition mechanism was similar to that of free HQ molecule, that is, polymer chain‐carrying radical or peroxy radical could be deactivated by abstracting hydrogen atom from hydroxyl group of immobilized HQ, and the resulting oxyradical (semiquinone radical) combined with another active chain free radical. According to this mechanism, a devised redox initiator consisting of sodium hydrogen sulfite and ammonium persulfate was used to initiate FRP of AA in water at low temperature (50 °C). High crystalline biaxial oriented PP film with HQ immobilized was deliberately laid in this system as a radical trap to capture poly(acrylic acid) (PAA) short chain radical. Through X‐ray photoelectron spectra (XPS) analysis it was found that the atom ratio of C_HQ (carbon in HQ) to C_COOH (carbon in COOH) decreased with prolonging polymerization time and became stable after about 30 min. The formed PAA short chain on the surface showed a distribution of monolayer, and the saturated thickness was calculated as 5–7 Å. The degree of polymerization of graft chain in PAA monolayer was estimated as 15–20 through three different models. Relating to surface coverage being 100% in ideal densely packed PAA monolayer, real monolayer surface coverage in such reaction system was estimated as 12.3–18.5%. This method was expected to give us a general approach for constructing kinds of graft polymer monolayer on polymeric substrate, because the involved chemistry was only common inhibition reaction between immobilized inhibitor (HQ) and FRP system in solution (herein redox initiating system of AA). We named this grafting chemistry as confined surface inhibition reaction. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 745–755, 2007     

Crystallinity in Free Radical Polymerized Polyvinyl p-t-butylbenzoate)

The photoinduced graft polymerization of acrylic acid and n-butyl acrylate on polyvinyl chloride or carbon monoxide-vinyl chloride copolymer by using benzophenone as a sensitizer was carried out. In graft polymerization of acrylic acid, the degree of grafting was low. However, graft polymerization of n-butyl acrylate or acrylic acid-n-butyl acrylate were higher than that of acrylic acid. Turbidimetry, DTA, and TGA of the graft polymer were examined. As the graft polymer was a weak polyacid, the pK_a was estimated according to the Henderson equation, and the relationship between pK_a and the acrylic acid unit content in the graft polymer was derived.     

Grafting of Acrylamide On 1, 1, 2, 2-Tetra-Chloroethane Preswelled Polyethylene Terephthalate) Films Using Azobisisobutyronitrile Initiator

Abstract

Graft polymerization of acrylamide (AAm) on 1, 1, 2, 2 tetrachloro-ethane (TCE) preswelled poly(ethylene terephthalate) (PET) films were performed with chemical initiation method using asobisiso-butyronitrile (AIBN) initiator. Temperature was found to have a greater effect on the swelling then the swelling time. Variation of the graft yield with polymerization temperature, time, AIBN concentration, AAm concentration, AIBN and AAm inclusion times were investigated. The optimum temperature for grafting was found to be 70°CC. The graft yield was observed to increase with polymerization time, AAm concentration, initiator and monomer diffusion time up to a saturation graft yield and then leveled off. An increase in AIBN concentration first enhanced the percent grafting then showed a decrease. The addition of some salts (Ni²⁺, Cr³⁺, Co²⁺, Cu²⁺) on the rate of grafting was also investigated. From the temperature dependence of the initial rate of grafting, the overall activation energy was found to be 4. 1 kcal/mol and relevant rate equation have been derived. The effect of grafting on film propities, such as water absorption capacity, intrinsic viscosity were determined. Grafted films were characterized by FTIR spectros-copy and scanning electron microscopy (SEM).     

二步法聚丙烯/丙烯酸表面接枝聚合研究

研究了二步法聚丙烯膜表面的丙烯酸接枝反应 .实验发现 ,以醋酐为溶剂的反应体系所得接枝率明显好于以水为溶剂的体系 ;接枝率随光敏剂浓度、单体浓度增大而增加 ;提高反应温度 ,可使接枝率明显增大 ;接枝后的聚丙烯膜表面亲水性可明显改善 .并用红外光谱证实了丙烯酸在聚丙烯膜表面的接枝 .