Mn掺杂LiFePO4的第一性原理研究

采用基于密度泛函理论的第一性原理方法, 计算了不同Mn掺杂浓度LiFe_1-xMn_xPO₄ (x=0,0.25,0.50,0.75) 的电子结构. 同时采用流变相辅助高温固相碳热还原法制备了LiFe_1-xMn_xPO₄ (x= 0,0.25,0.50,0.75) 材料. 理论计算表明: LiFePO₄具有E_g = 0.725 eV的带隙宽度, 为半导体材料. 通过Fe位掺杂25%的Mn离子可最大程度地 减小材料带隙宽度、降低Fe---O键及Li---O键键能, 进而提高材料的电子电导率及锂离子扩散速率. 实验结果亦表明, 当Mn掺杂量x=0.25时, 材料具有最优的电化学性能, 其具有约为158 mAh· g^-1的放电比容量以及551 Wh· kg^-1的能量密度. 理论计算与实验结果非常符合.     

Sm-N共掺杂对锐钛矿相TiO2的电子结构和吸收光谱影响的第一性原理研究

采用基于密度泛函理论框架下的第一性原理平面波超软赝势方法, 建立了N, Sm分别单掺杂以及Sm-N共掺杂的锐钛矿TiO₂超胞模型, 对其态密度、能带结构和吸收光谱进行了计算. 结果表明: N单掺杂的锐钛矿TiO₂的红移效果最强, 但Sm-N共掺杂锐钛矿TiO₂的载流子寿命更长, 且共掺杂形成的体系更加稳定.     

3d过渡金属掺杂锐钛矿相TiO2的第一性原理研究

采用基于密度泛函理论的平面波超软赝势方法研究了纯锐钛矿相TiO₂及掺杂3d过渡金属TiO₂的几何、电子结构及光学性质. 计算结果表明掺杂能级的形成主要是掺杂过渡金属3d轨道的贡献，掺杂能级在禁带中的位置是决定TiO₂吸收带边能否出现红移的重要因素. Cr，Mn，Fe，Ni，Co，Cu掺杂使TiO₂的吸收带边产生红移，并在可见光区有一定的吸收系数； Sc，Zn掺杂使TiO₂的吸收带边产生蓝移，但在可见光区有较大的吸收系数；掺V不但使TiO₂的吸收带边产生红移，增强了在紫外光区的光吸收，而且在可见光区有非常大的吸收系数.     

二价金属元素掺杂对LiCoO2体系电子输运性质的影响

为了解释Ca掺杂与Mg掺杂在影响锂离子二次电池正极材料LiCoO₂体系电子输运性质方面的不同效应，采用基于密度泛函理论的第一性原理方法研究了该体系的电子结构.计算结果表明，虽然在LiCoO₂体系中用Ca或Mg替代Co都会在费米能级附近产生部分占据的受主带，但两者对应的电子态都具有明显的局域化特征；此外，与Mg掺杂体系明显不同的是，Ca掺杂体系的受主带与价带之间存在清晰的带隙.这一带隙的存在正是Ca掺杂不能明显提高LiCoO₂体系电导率的主要原因.此外，Ca²⁺与Mg²⁺离子半径的较大差别也是造成这两个掺杂体系的电导率存在明显差异的一个重要因素.     

Eu掺杂量对锐钛矿相TiO2电子寿命和吸收光谱影响的第一性原理研究

采用基于密度泛函理论框架下的第一性原理平面波超软赝势方法,建立了不同Eu掺杂量的锐钛矿相TiO₂超胞模型,计算了其态密度、差分电荷密度、能带结构和吸收光谱.结果发现:掺杂后Eu在TiO₂的禁带中产生杂质能级.通过对比两种不同Eu掺杂量(1.39at%和2.08at%)下的锐钛矿TiO₂的能带结构,发现掺杂量越高,杂质能级越向深能级方向移动,说明电子复合率随杂质浓度增加而增加,即电子寿命变小,同时吸收光谱红移越显著,强度越强.根据实际需要,可在锐钛矿TiO₂中适量掺杂Eu,在适当减少电子寿命情况下,使吸收光谱红移.     

TiY2N@C80电子结构的第一性原理研究

采用第一性原理方法研究了TiY₂N@C₈₀分子的几何、振动和电子性质．理论计算结果表明TiY₂N@C₈₀分子的电子结构性质明显与Sc₃N@C₈₀和Y₃N@C₈₀的不同,而与TiSc₂N@C₈₀相近．对TiY₂N@C₈₀分子进行载流子掺杂时,其磁性     

LiFePO4中对位缺陷的第一性原理研究

基于考虑了Fe-3d电子间的库仑作用U和交换作用J的GGA+U方案,应用第一性原理计算方法系统研究了LiFePO₄的对位缺陷,以及对位缺陷的形成对材料的电导率和离子扩散速率的影响.结果表明,Li/Fe交换缺陷是最容易形成的,形成缺陷后的Fe—O键变长,扩宽了Li离子传输通道,有利于Li离子在通道中的扩散,对材料电化学性能的改善起到了一定的作用.     

YFeO3的电子结构和光学性质的第一性原理研究

稀土正铁氧体YFeO₃呈正交钙钛矿结构,其晶体和纳米晶材料在电极材料、 传感器和光催化领域具有重要的应用价值.用平面波赝势方法,采用广义梯度近似、改进的Perdew-Burke-Emzerhof交换-关联势、 实空间超软赝势计算方案,研究了YFeO₃晶体的几何结构、电子结构和光学性质. 计算得到的晶格参量与报道的实验结果一致.通过对能带结构、态密度、介电函数、吸收系数和光电导率的计算和分析, 确定YFeO₃是直接能隙半导体,能隙E_g约为2.22 eV,阐明了YFeO₃晶体和纳米晶具有较好的可见光催化性能.     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

Sn3InSb4合金嵌Li性能的第一性原理研究

采用第一性原理超软赝势平面波方法计算了Sn₃InSb₄的嵌Li性能,得到各种嵌Li相的嵌Li形成能、理论质量比容量、体积膨胀率、能带结构、态密度和差分电荷密度等.从能量角度分析,Li在嵌入时,优先占据晶胞的四面体间隙位置,然后逐步挤出处于节点位置的Sn原子和In原子.在嵌Li过程中,材料表现出较大的体积膨胀率(11.74%-43.40%),这是导致Sn₃InSb₄作为Li离子电极材料循环性能差的重要原因.态密度计算表明,体系的导电性能首先随嵌Li量的增加而增加,当所有的间隙位置被Li填满,发生Sn的替换反应时,富Li态合金相的导电性反而下降.     

First-principles study of ferromagnetism in Zn- and Cd-doped SnO2

The electronic structures and magnetic properties of Zn- and Cd-doped SnO₂ are investigated using first-principles calculations within the generalized gradient approximation (GGA) and GGA+U scheme. The substitutional Zn and Cd atoms introduce holes in the 2p orbitals of the O atoms and the introduced holes are mostly confined to the minority-spin states. The magnetic moment induced by doping mainly comes from the 2p orbitals of the O atoms, among which the moment of the first neighboring O atoms around the dopant are the biggest. The U correction for the anion-2p states obviously increases the moment of the first neighboring O atoms and transforms the ground states of the doped SnO₂ from half-metallic to insulating. The magnetic coupling between the moments induced by two dopants is ferromagnetic and the origin of ferromagnetic coupling can be attributed to the p–d hybridization interaction involving holes.     

First-principles study of native defects in rutile TiO2

Native point defects in the rutile TiO₂ are studied via first-principles pseudopotential calculations. Except for the two antisite defects, all the native point defects have low formation energies. Under the Ti-rich growth condition, high concentrations of titanium interstitials and oxygen vacancies would form spontaneously in p-type samples; whereas high concentrations of titanium vacancies would form spontaneously in n-type samples regardless of the oxygen partial pressure.     

First-principles calculations on Al/AlB2 interfaces

The AlB₂ (1 1 1) surfaces and Al (1 1 1)/AlB₂ (0 0 0 1) interface were studied by first-principles calculations to clarify the heterogeneous nucleation potential of α-Al grains on AlB₂ particles in purity aluminium and hypoeutectic Al-Si alloys. It is demonstrated that the AlB₂ (0 0 0 1) surface models with more than nine atomic layers exhibit bulk-like interior, wherein the interlayer relaxations localized within the top three layers are well converged. The outmost layer of AlB₂ free surface having a preference of metal atom termination is evidenced by surface energy calculations. With Al atoms continuing the natural stacking sequence of bulk AlB₂, Al-Al metallic bonds are formed across interface during the combination of Al atoms with Al-terminated AlB₂ surface. The calculated interfacial energy of the Al/AlB₂ interface is much larger than that between the α-Al and aluminium melts, elucidating the poor nucleation potency of α-Al grains on AlB₂ particles from thermodynamic considerations.     

Investigation of tetragonal ReN2 and WN2 with high shear moduli from first-principles calculations

Two new transition metal dinitrides, ReN₂ and WN₂, with the P4/mmm structure are investigated by the first-principles calculations. The computed shear moduli of 327 GPa for ReN₂ and 334 GPa for WN₂ exceed those of all transition metal dinitrides previously reported. The estimated theoretical hardness are 46.3 GPa for ReN₂ and 47.9 GPa for WN₂, respectively. The calculated high shear moduli and hardness indicate that they are potential ultrahard materials. It is important to note that the computed hardness of the weakest bond are 34.7 GPa (W-N) for WN₂ and 33.1 GPa (Re-N) for ReN₂, much higher than that of 21.1 GPa (Re-B) for ReB₂, which suggests that tetragonal ReN₂ and WN₂ are probably harder than ReB₂. The total and partial electron density of states and the electron localization function for ReN₂ and WN₂ are analyzed. We attribute the high bulk modulus, shear modulus, and hardness to a three-dimensional covalently bonded framework in tetragonal ReN₂ and WN₂. Our calculations show that tetragonal ReN₂ is expected to be synthesized above 62.7 GPa and tetragonal WN₂ may be hard to be synthesized.     

Stability of La2O3 and GeO2 passivated Ge surfaces during ALD of ZrO2 high-k dielectric

La₂O₃ grown by atomic layer deposition (ALD) and thermally grown GeO₂ are used to establish effective electrical surface passivations on n-type (1 0 0)-Ge substrates for high-k ZrO₂ dielectrics, grown by ALD at 250 °C substrate temperature. The electrical characterization of MOS capacitors indicates an impact of the Ge-surface passivation on the interfacial trap density and the frequency dependent capacitance in the inversion regime. Lower interface trap densities can be obtained for GeO₂ based passivation even though a chemical decomposition of the oxidation states occur during the ALD of ZrO₂. As a consequence the formation of a ZrGeO_x compound inside the ZrO₂ matrix and a decline of the interfacial GeO₂ are observed. The La₂O₃ passivation provides a stable amorphous lanthanum germanate phase at the Ge interface but also traces of Zr germanate are indicated by X-ray-Photoelectron-Spectroscopy and Transmission-Electron-Microscopy.     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

First-principles study of elastic and thermo-physical properties of kesterite-type Cu2ZnSnS4

The lattice constants and elastic constants of the kesterite-type Cu₂ZnSnS₄ have been calculated using density-functional theory (DFT). The calculated lattice constants are in good agreement with the experimental data. The calculated elastic constants indicate that the bonding strength along the [1 0 0] and [0 1 0] directions is as strong as the one along the [0 0 1] direction. The high B/G ratio shows that the kesterite-type Cu₂ZnSnS₄ compound has ductile behavior. Finally, using the Debye model, the volume, bulk modulus and heat capacity as a function of temperature for the kesterite-type CZTS have been estimated at different pressures. The Debye temperature and Gruneisen parameter are 157 K and 2.28 at 300 K temperature, respectively. The present results can give some information for the design of the kesterite-type CZTS compounds, and these can also be used to stimulate future experimental and theoretical work.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

MgH2(110)表面Pd单原子催化氢脱附反应的第一性原理研究

本文采用第一性原理密度泛函理论计算研究了MgH₂(110)表面吸附单原子Pd后的氢脱附反应. 计算发现,在吸附一个Pd单原子后,MgH₂(110)表面氢脱附反应的能垒可以从1.802 eV显著地降低到1.154 eV,表明Pd单原子对于氢脱附具有很强的催化效应. 并且,Pd单原子催化还可以将氢脱附的温度从573 K显著地降低到了367 K,从而使MgH₂(110)表面的氢脱附反应更加容易和快速地发生. 此外,通过MgH₂(110)表面氢溢出机制的反向过程来讨论了氢脱附反应的微观过程. 该研究表明Pd/MgH₂薄膜在未来的实验中可作为良好的储氢材料.     

Thermodynamic properties of LiCu2O2 multiferroic compound

A spin model of quasi-one-dimensional LiCu₂O₂ compound with ground state of ellipsoidal helical structure has been adopted. The helical axis is along the diagonal of CuO₄ squares. By taking into account the interchain coupling and exchange anisotropy, the exotic magnetic properties and ferroelectricity induced by spiral spin order have been studied by performing Monte Carlo simulation. The simulation results qualitatively reproduce the main characters of ferroelectric and magnetic behaviors of LiCu₂O₂ compound and confirm the low-temperature noncollinear spiral ordering. Furthermore, by performing the calculations of spin structure factor, we systematically investigate the effects of different exchange couplings on the lower-temperature magnetic transition, and find that the spiral spin order depends not only on the ratio of nearest and next-nearest neighbor inchain spin coupling but also strongly on the exchange anisotropy.