π平面上原状土的空心扭剪试验

为了通过空心扭剪试验获得原状土在π 平面上的屈服特性,在分析空心扭剪试验仪加载过程和加载特点的基础上,研究了空心圆柱试样可实现的应力状态,并设计了相应的加载路径．与重塑试样不同,原状土样的初始应力状态位于K0 固结线上而不是等倾线上,因此,其加载路径应从原点开始沿K0 固结线行至原始应力状态,然后再在π 平面上进行以初始应力为起点的等p 试验．在考虑原状土的初始应力状态和各项异性的基础上,针对具有不同主应力方向角的平行试样,给出了等p 条件下保持主应力方向角不变的加载路径实现方法,采用该方法可得到任意平均主应力时π 平面上六分之一范围内的屈服曲线,该范围对应于大主应力方向角从-45o~45o．本文设计的加载方案可完成真三轴试验的部分功能,但经济成本相对较低,操作方法简单易行．     

TORSIONAL VIBRATIONS OF RIGID CIRCULAR PLATE ON TRANSVERSELY ISOTROPIC SATURATED SOIL

An analytical method was presented for the torsional vibrations of a rigid disk resting on transversely isotropic saturated soil. By Hankel transform, the dynamic governing differential equations for transversely isotropic saturated poroelastic medium were solved. Considering the mixed boundary-value conditions, the dual integral equations of torsional vibrations of a rigid circular plate resting on transversely isotropic saturated soil were established. By appropriate transform, the dual integral equations were converted into a Fredholm integral equation of the second kind. Subsequently, the dynamic compliance coefficient, the torsional angular amplitude of the foundation and the contact shear stress were expressed explicitly. Selected examples were presented to analyse the influence of saturated soil's anisotropy on the foundation's vibrations.     

一种基于SHTB的Ⅱ型动态断裂实验技术

冲击剪切载荷作用下动态断裂韧性的测定是材料力学性能和断裂行为研究中重要组成部分.为了测定材料的Ⅱ型动态断裂韧性,许多学者采用不同的试样与实验方法进行了实验,但限于实验条件,裂纹断裂模式往往是I+Ⅱ复合型,而不是纯Ⅱ型,因而不能准确测得材料的Ⅱ型动态断裂韧性.鉴于此,本文基于分离式霍普金森拉杆(split Hopkinson tension bar,SHTB)实验技术,提出一种改进的紧凑拉伸剪切(modified compact tension shear,MCTS)试样,通过夹具对MCTS试样施加约束,从而保证试样按照纯Ⅱ型模式断裂.采用实验-数值方法对MCTS试样动态加载过程进行分析,将实验测得的波形输入有限元软件ANSYS-LSDYNA,得到了裂纹尖端应力强度因子-时间曲线,并与紧凑拉伸剪切(compact tension shear,CTS)试样进行了对比.同时采用数字图像相关法进行了实验,验证了有限元分析结果.结果表明,MCTS试样在整个加载过程中K_I K_Ⅱ,裂纹没有张开;而CTS试样在同样的加载过程中K_IK_Ⅱ,出现裂纹张开现象.这说明MCTS试样能够准确地测定材料的Ⅱ型动态断裂韧性,为材料动态力学测试提供了一种有效的实验技术.     

A Novel Method for Dynamic Short-Beam Shear Testing of 3D Woven Composites

A new test method for performing dynamic short-beam shear tests using a momentum trapped Hopkinson pressure bar is proposed. Angle-interlock 3D woven composite specimens were tested under quasi-static and dynamic loading conditions to determine the effect of loading rate on damage evolution. The equilibrium condition in the composite specimen under dynamic loads was verified using finite element analysis of the experiment. A high speed camera was used to capture delamination initiation and propagation during both quasi-static and dynamic experiments. Analysis of the load-deflection curves and the high speed images revealed a good correlation between the modes of damage initiation and propagation with the features in the loading response. The apparent inter-laminar shear strength and the bending stiffness increased with rate of loading. While the damage was observed to propagate at a relative steady rate during quasi-static loading, the high rate of energy input during dynamic loading resulted in a rapid propagation of damage and a subsequent loss of stiffness in the composite as noted in the load-deflection curve.     

Dynamic Experiments using Simultaneous Compression and Shear Loading

Material characterization at high strain rates under simultaneous compression and shear loading has been a challenge due to the differing normal and shear wave speeds. An experimental technique utilizing the compression Kolsky bar apparatus was developed to apply dynamic compression and shear loading on a specimen nearly simultaneously. Synchronization between the compression and shear loading was realized by generating the torsion wave near the specimen which minimizes the time difference between the arrival of the compression and torsion waves. This modified Kolsky bar makes it possible to characterize the dynamic response of a material to combined compression and shear impact loading. This method can also be applied to study dynamic friction behavior across an interface under controlled loading conditions. The feasibility of this method is demonstrated in the dynamic characterization of a simulant polymer bonded explosive material.     

Torsional impact response of a penny-shaped crack in a functional graded strip

The torsional impact response of a penny-shaped crack in a nonhomogeneous strip is considered. The shear modulus is assumed to be functionally graded such that the mathematics is tractable. Laplace and Hankel transforms were used to reduce the problem to solving a Fredholm integral equation. The crack tip stress field is obtained by considering the asymptotic behavior of Bessel function. Explicit expressions of both the dynamic stress intensity factor and the energy density factor were derived. And it is shown that, as crack driving force, they are equivalent for the present crack problem. Investigated are the effects of material nonhomogeneity and strip‘s highness on the dynamic fracture behavior.Numerical results reveal that the peak of the dynamic stress intensity factor can be suppressed by increasing the nonhomogeneity parameter of the shear modulus, and that the dynamic behavior varies little with the adjusting of the strip‘ s highness.     

Rheological characterization of carbon nanotubes/poly(ethylene oxide) composites

Rheological properties of poly(ethylene oxide) nanocomposites embedded with carbon nanotubes (CNTs) were investigated in the present study. It was found that the CNT nanocomposites had a higher effective filler volume fraction than the real filler volume fraction, which yielded a drastic enhancement of shear viscosity. As the CNT loading in the nancomposites increases, non-Newtonian behavior was observed at the low-shear-rate region in the steady shear experiments. Oscillatory dynamic shear experiments showed that more addition of the CNTs led to stronger solidlike and nonterminal behaviors. To identify a dispersion state of the CNTs, field emission scanning electron spectroscopy and transmission electron microscopy were adopted and thermal analysis was also performed by using differential scanning calorimetry. The existence of percolated network structures of the CNTs even at a low CNT loading was verified by rheological properties and electrical conductivities.     

Simulating shear behavior of a sandy soil under different soil conditions

Understanding of soil shear behavior is very important in the field of agricultural machinery and soil dynamics. In this study, a discrete element model was developed using a simulation tool, Particle Flow Code in Three Dimensions (PFC^3D). The model simulates direct shear tests of soil and predicts soil shear behavior, in terms of shear forces and displacements. To determine and calibrate model parameters (stiffness of particles, strength and stiffness of bond between particles), laboratory direct shear tests were conducted to examine effects of soil moisture content and bulk density on shear behaviors of a sandy soil. Three soil moisture levels (0.02%, 13.0%, and 21.5%) and four bulk density levels (0.99, 1.28, 1.36, and 1.50 Mg/m³) were used in the tests. The test results showed that in general drier and denser soil conditions produced higher shear forces. Based on the test results, the bond strengths of the model particles were determined from soil cohesion and internal friction angle. The model particle stiffness was calibrated based on the yield forces from the tests. The calibrated particle stiffness varied from 1.0 × 10³ to 8.2 × 10³ N/m, depending on soil moisture and density levels. The bond stiffness calibrated was 1.0 × 10⁷ Pa/m for all soil conditions.     

Dynamic analysis of 3-D beam elements including warping and shear deformation effects

In this paper the dynamic analysis of 3-D beam elements restrained at their edges by the most general linear torsional, transverse or longitudinal boundary conditions and subjected in arbitrarily distributed dynamic twisting, bending, transverse or longitudinal loading is presented. For the solution of the problem at hand, a boundary element method is developed for the construction of the 14 × 14 stiffness matrix and the corresponding nodal load vector of a member of an arbitrarily shaped simply or multiply connected cross section, taking into account both warping and shear deformation effects, which together with the respective mass and damping matrices lead to the formulation of the equation of motion. To account for shear deformations, the concept of shear deformation coefficients is used, defining these factors using a strain energy approach. Eight boundary value problems with respect to the variable along the bar angle of twist, to the primary warping function, to a fictitious function, to the beam transverse and longitudinal displacements and to two stress functions are formulated and solved employing a pure BEM approach that is only boundary discretization is used. Both free and forced transverse, longitudinal or torsional vibrations are considered, taking also into account effects of transverse, longitudinal, rotatory, torsional and warping inertia and damping resistance. Numerical examples are presented to illustrate the method and demonstrate its efficiency and accuracy. The influence of the warping effect especially in members of open form cross section is analyzed through examples demonstrating the importance of the inclusion of the warping degrees of freedom in the dynamic analysis of a space frame. Moreover, the discrepancy in the dynamic analysis of a member of a spatial structure arising from the ignorance of the shear deformation effect necessitates the inclusion of this additional effect, especially in thick walled cross section members.     

聚氨酯泡沫塑料动态剪切力学行为的研究

通过大型精密分段式Ｈｏｐｋｉｎｓｏｎ 扭杆实验装置对聚氨酯泡沫塑料进行了动态扭转实验,研究了聚氨酯泡沫塑料在剪切应力波加载下的力学行为,得到了这类材料的动态剪切应力 应变曲线和动态力学性能参数。此外,针对动态扭转破坏试件断口进行了扫描电镜分析,研究了泡沫塑料动态剪切破坏的机制。还给出了同准静态扭转实验结果的比较。     

Shear-strain-rate effects in a high-strength aluminum alloy

Methods of investigating the plastic flow of materials at high rates are reviewed, and experiments are described in which thin-walled tubular specimens were subjected to dynamic torsional loading. These experiments were performed using a modified version of a torsional Hopkinsonbar apparatus used in earlier work. The results show that, at strain rates of order 10³ sec⁻¹, the stress-strain curve of the alloy tested does not differ significantly from that found at 10⁻³ sec⁻¹. In tests involving the propagation of a stress increment, however, it was found that the speed of propagation was that of elastic shear waves, indicating that the initial response of the material is essentially rate dependent.     

Shear Failure of Inconel 718 under Dynamic Loads

Kinetics of deformation and fracture of nickel–iron alloy Inconel 718 under dynamic shear loading was measured using a split torsional Hopkinson bar facility and high-speed photography. Tubular specimens with a reduced gage length and a starter notch were sheared at strain rates up to 6 × 10³ s⁻¹. High-speed photographs of fiducial lines scribed on the specimen surface showed the development of local strains and cracking. This paper describes the experimental and analytical procedures, illustrates average and local plastic strain evolution, and presents shear crack initiation times and propagation speeds.     

邯郸与太原两地粉土动力特性的试验研究

对邯郸5个工程场区和太原1个工程场区的粉土进行了循环荷载幅值为不规则变化的动模量试验。试验研究发现,粉土的动模量衰减的比砂土慢;其动模量衰减到最大动模量的85%时,开始表现出塑性特征,因此,在动模量衰减到最大动模量的85%之前降低循环动荷载的幅值,动模量仍能大部分回到初始值。粘粒含量的变化使粘粒在粉土中表现出不同的作用,当粘粒含量小于10%时,动强度随粘粒含量的增加而降低;当粘粒含量大于10%后,动强度随粘粒含量的增加而增加。     

An experimental study on subsequent yield surface after finite shear prestraining

An equimodulus surface is introduced and the subsequent yield surface after large finite shear prestraining is experimentally investogated. Fully annealed, thin-walled copper tubular specimens were subjected to large torsional loading and partial unloading; strain gages were carefully mounted on the specimen after the application of pure shear loading. Specimens were then subjected to various combined tension-torsion loadings. Influences of he von Mises and Tresca equivalent offset strains on the subsequent yield surfaces are studied. On examining the experimental results reported in this article, it was found that the smaller the offset strains, the more distorted are the subsequent yield surfaces. At the torsional preloading point, a rounded corner was developed, whereas in the region opposite to the preloading point, the subsequent yield surface was flattened. When large von Mises offset strains were used, the corresponding subsequent yield surfaces passed through the von Mises loading surface. But this was not the case when Tresca offset strains were used. The subsequent yield surface determined by the back extrapolation method was almost completely outside the von Mises loading surface. On the other hand, the subsequent yield surface determined by the back extrapolation method was close to the Tresca loading surface. It is also found that the equimodulus surface is distorted and cannot simply be described by the combined kinematic and isotropic hardening rule.     

压剪复合平板冲击加载技术进展及其应用

自20世纪70年代末发明压剪炮以来, 压剪复合冲击加载实验技术和诊断技术有了长足进展, 应用也日益广泛.由于压剪联合加载波直接反映了材料的动态剪切特性, 对于认识材料的屈服、损伤演化、失效、相变、界面滑移等动态行为和机理, 构筑更全面的本构模型能够提供必要的附加信息.本文主要讨论气炮实验中压剪复合应力波的产生方式, 诊断技术, 以及在压剪复合塑性波和动高压本构模型、聚合物压剪冲击行为、剪切波跟踪法(SWT)和水泥基复合材料的损伤和失效、界面动摩擦行为、冲击相变、动态损伤和断裂等方面的研究与应用进展.      

Discrete simulation and micromechanical analysis of two-dimensional saturated granular media

In this study, a novel approach to incorporate the pore water pressure in the discrete element method （DEM） to comprehensively model saturated granular media was developed. A numerical model was constructed based on the DEM by implanting additional routines in the basic DEM code; pore water pressure calculations were used with a two-dimensional （2D） model to simulate the undrained behavior of satu- rated granular media. This model coupled the interaction of solid particles and the pore fluid in saturated granular media. Finally, several 2D undrained shear tests were simulated. The test results showed that the model could predict the response of the saturated granular soil to shear loading. The effect of initial compaction was investigated. Biaxial tests on dense and loose specimens were conducted, and the effect of the initial density on the change in shear strength and the volume change of the system was inves- tigated. The overall behavior of loose and dense specimens was phenomenologically similar to the real granular material. Constant volume tests were simulated, and the results were compared to those from the coupled model. Induced anisotropy was micromechanically investigated by studying the contact force orientation. The change in anisotropy depended on the modeling scheme. However, the overall responses of the media obtained usinz the couoled and constant volume methods were similar.     

Discrete simulation and micromechanical analysis of two-dimensional saturated granular media

In this study, a novel approach to incorporate the pore water pressure in the discrete element method (DEM) to comprehensively model saturated granular media was developed. A numerical model was constructed based on the DEM by implanting additional routines in the basic DEM code; pore water pressure calculations were used with a two-dimensional (2D) model to simulate the undrained behavior of saturated granular media. This model coupled the interaction of solid particles and the pore fluid in saturated granular media. Finally, several 2D undrained shear tests were simulated. The test results showed that the model could predict the response of the saturated granular soil to shear loading. The effect of initial compaction was investigated. Biaxial tests on dense and loose specimens were conducted, and the effect of the initial density on the change in shear strength and the volume change of the system was investigated. The overall behavior of loose and dense specimens was phenomenologically similar to the real granular material. Constant volume tests were simulated, and the results were compared to those from the coupled model. Induced anisotropy was micromechanically investigated by studying the contact force orientation. The change in anisotropy depended on the modeling scheme. However, the overall responses of the media obtained using the coupled and constant volume methods were similar.     

Dynamic effective shear strength of saturated sand

The dynamic effective shear strength of saturated sand under cyclic loading is discussed in this paper. The discussion includes the transient time dependency behaviors based on the analysis of the results obtained in conventional cyclic triaxial tests and cyclic torsional shear triaxial tests. It has been found that the dynamic effective shear strength is composed of effective frictional resistance and viscous resistance, which are characterized by the strain rate dependent feature of strength magnitude, the coupling of consolidation stress with cyclic stress and the dependency of time needed to make the soil strength sufficiently mobilized, and can also be expressed by the extended Mohr-Coulomb's law. The two strength parameters of the dynamic effective internal frictional angle φ_d and the dynamic viscosity coefficient η are determined. The former is unvaried for different number of cyclic loading, dynamic stress form and consolidation stress ratio. And the later is unvaried for the different dynamic shear strain rate developed during the sand liquefaction, but increases with the increase of initial density of sand. The generalization of dynamic effective stress strength criterion in the 3-dimensional effective stress space is studied in detail for the purpose of its practical use. The project supported by the National Natural Science Foundation of China (10172070)     

Numerical and experimental direct shear tests for coarse-grained soils

The presence of particles larger than the permissible dimensions of conventional laboratory specimens causes difficulty in the determination of shear strength of coarse-grained soils. In this research, the influence of particle size on shear strength of coarse-grained soils was investigated by resorting to experimental tests in different scale and numerical simulations based on discrete element method (DEM). Experimental tests on such soil specimens were based on using the techniques designated as "parallel" and "scalping" to prepare gradation of samples in view of the limitation of laboratory specimen size. As a second approach, the direct shear test was numerically simulated on assemblies of elliptical particles. The behaviors of samples under experimental and numerical tests are presented and compared, indicating that the modification of sample gradation has a significant influence on the mechanical properties of coarse-grained soils. It is noted that the shear strengths of samples produced by the scalping method are higher than samples by the parallel method. The scalping method for preparing specimens for direct shear test is therefore recommended. The micromechanical behavior of assemblies under direct shear test is also discussed and the effects of stress level on sample behavior are investigated.     

辽西风积土动应力试验研究

通过对辽西地区风积土动三轴试验, 研究了动荷载作用下辽西风积土的动强度特性和抗液化特性.通过控制不同的动荷幅值、固结比和固结围压等试验条件, 获得了抗震设防烈度为7 度时, 辽西风积土的动应力值和抗液化剪应力比. 利用Excel 软件, 对试验数据进行回归处理, 得到了该土试样的动应力与固结比和固结围压两种因素的经验关系式. 试验和回归分析结果表明, 风积土的动应力与固结比和固结围压成正比. 试验研究了不同固结比条件下辽西地区风积土的液化强度特性, 获得了不同固结比条件下的抗液化剪应力比. 试验结果表明, 风积土的抗液化剪应力随着固结比的增加而增大. 上述试验结果对于辽西地区工程的抗震设计具有重要的指导意义和工程实用价值.