Palladium Nanoparticles Bonded to Two‐Dimensional Iron Oxide Graphene Nanosheets: A Synergistic and Highly Reusable Catalyst for the Tsuji–Trost Reaction in Water and Air

Low cost, high activity and selectivity, convenient separation, and increased reusability are the main requirements for noble‐metal‐nanocatalyst‐catalyzed reactions. Despite tremendous efforts, developing noble‐metal nanocatalysts to meet the above requirements remains a significant challenge. Here we present a general strategy for the preparation of strongly coupled Fe₃O₄ and palladium nanoparticles (PdNPs) to graphene sheets by employing polyethyleneimine as the coupling linker. Transmission electron microscopic images show that Pd and Fe₃O₄ nanoparticles are highly dispersed on the graphene surface, and the mean particle size of Pd is around 3 nm. This nanocatalyst exhibits synergistic catalysis by Pd nanoparticles supported on reduced graphene oxide (rGO) and a tertiary amine of polyethyleneimine (Pd/Fe₃O₄/PEI/rGO) for the Tsuji–Trost reaction in water and air. For example, the reaction of ethyl acetoacetate with allyl ethyl carbonate afforded the allylated product in more than 99 % isolated yield, and the turnover frequency reached 2200 h^?1. The yield of allylated products was 66 % for Pd/rGO without polyethyleneimine. The catalyst could be readily recycled by a magnet and reused more than 30 times without appreciable loss of activity. In addition, only about 7.5 % of Pd species leached off after 20 cycles, thus rendering this catalyst safer for the environment.     

Shape-dependent catalytic activity of copper oxide-supported Pd(0) nanoparticles for Suzuki and cyanation reactions

Palladium nanoparticles supported on different shapes of nanocrystalline CuO are prepared by the treatment of Cu(NO₃)₂ and Pd(OAc)₂ in polyethylene glycol (PEG-6000). The shapes of the CuO/Pd composite are dependent on the amount of PEG used. Suzuki coupling was catalyzed efficiently by the oval-shaped material, whereas the rod shape facilitates the cyanation reaction. The CuO/Pd catalyst is recovered and reused for subsequent Suzuki reactions; however, cyanation poisons the catalyst for further use. Both these reactions are very clean and high yielding.     

Di(2-pyridyl)methylamine-palladium dichloride complex covalently anchored to a styrene-maleic anhydride co-polymer as recoverable catalyst for C-C cross-coupling reactions in water

A new polymer-supported di(2-pyridyl)methylamine-palladium dichloride complex covalently anchored to a styrene-alt-maleic anhydride co-polymer is prepared. This complex catalyzes Heck, Suzuki and Sonogashira cross-coupling reactions in neat water with similar efficiency than the monomeric complex. The turnover number (TON) of this polymer reaches up to 10⁴ for Heck reactions, whereas for Suzuki and Sonogashira couplings TONs up to 10⁵ are achieved. There is low leaching of palladium after filtration of the polymer and the activity remains almost constant after fourth and five reaction cycles especially in Sonogashira reactions. In the case of the Suzuki reaction Pd nanoparticles are dispersed into the polymer after the first cycle according to TEM images and 2.4% of Pd are found by ICP-OES in the corresponding filtrate. Alternatively, these palladium-catalyzed reactions can also be performed under microwave heating. These couplings take place with better efficiency with polymer-supported di(2-pyridyl)methylamine-palladium dichloride complex than with the polyurea-encapsulated Pd EnCat™ 40.     

Crystalline Hybrid Solid Materials of Palladium and Decamethylcucurbit[5]uril as Recoverable Precatalysts for Heck Cross‐Coupling Reactions

A series of M? Pd? Me₁₀CB[5] (M=Li, Na, K, Rb, and Cs; Me₁₀CB[5]=decamethylcucurbit[5]uril) hybrid solid materials have been successfully synthesized for the first time through a simple diffusion method. These as‐prepared hybrid solids have been applied as phosphine‐free precatalysts for Heck cross‐coupling reactions with excellent catalytic performance and good recyclability. In the processes of the catalytic reactions, the activated Pd^II species were released from the crystalline hybrid precatalysts and transformed into catalytically active Pd nanoparticles, which have been demonstrated as key to carry on the catalytic reactions for the recoverable precatalysts M? Pd? Me₁₀CB[5] (M=K, Rb, and Cs). It has also been rationalized that the introduction of different alkali metals afforded crystalline hybrid precatalysts with different crystal structures, which are responsible for their diversified stability and reusability presented in Heck reactions.     

Tailored Synthesis of Various Nanomaterials by Using a Graphene‐Oxide‐Based Gel as a Nanoreactor and Nanohybrid‐Catalyzed CC Bond Formation

New graphene oxide (GO)‐based hydrogels that contain vitamin B₂/B₁₂ and vitamin C (ascorbic acid) have been synthesized in water (at neutral pH value). These gel‐based soft materials have been used to synthesize various metal nanoparticles, including Au, Ag, and Pd nanoparticles, as well as nanoparticle‐containing reduced graphene oxide (RGO)‐based nanohybrid systems. This result indicates that GO‐based gels can be used as versatile reactors for the synthesis of different nanomaterials and hybrid systems on the nanoscale. Moreover, the RGO‐based nanohybrid hydrogel with Pd nanoparticles was used as an efficient catalyst for C? C bond‐formation reactions with good yields and showed high recyclability in Suzuki–Miyaura coupling reactions.     

A Palladium Nanoparticle–Nanomicelle Combination for the Stereoselective Semihydrogenation of Alkynes in Water at Room Temperature

The addition of NaBH₄ to Pd(OAc)₂ in water containing nanomicelles leads to the generation of H₂ and Pd nanoparticles. Subsequent reduction of disubstituted alkynes affords Z‐alkenes in high yields. These reactions are general, take place in water at ambient temperatures, and offer recycling of the aqueous reaction mixture along with low overall E Factors.     

Pd/MOF‐199: As an efficient heterogeneous catalyst for the Suzukie Miyaura cross‐coupling reaction

Successful deposition of Pd nanoparticles is described using MOF‐199 as a support. Various characterization techniques including FTIR, XRD, SEM, BET‐BJH, TG‐DTA, and NH₃‐TPD were used to verify the efficiency of catalysts. Pd/MOF‐199 is utilized as a catalyst for Suzukie Miyaura reactions with reasonable to excellent reaction yields under reflux conditions in H₂O: ethanol solvent.     

Selective Hydrogenation of Acrolein Over Pd Model Catalysts: Temperature and Particle‐Size Effects

The selectivity in the hydrogenation of acrolein over Fe₃O₄‐supported Pd nanoparticles has been investigated as a function of nanoparticle size in the 220–270 K temperature range. While Pd(111) shows nearly 100 % selectivity towards the desired hydrogenation of the C=O bond to produce propenol, Pd nanoparticles were found to be much less selective towards this product. In situ detection of surface species by using IR‐reflection absorption spectroscopy shows that the selectivity towards propenol critically depends on the formation of an oxopropyl spectator species. While an overlayer of oxopropyl species is effectively formed on Pd(111) turning the surface highly selective for propenol formation, this process is strongly hindered on Pd nanoparticles by acrolein decomposition resulting in CO formation. We show that the extent of acrolein decomposition can be tuned by varying the particle size and the reaction temperature. As a result, significant production of propenol is observed over 12 nm Pd nanoparticles at 250 K, while smaller (4 and 7 nm) nanoparticles did not produce propenol at any of the temperatures investigated. The possible origin of particle‐size dependence of propenol formation is discussed. This work demonstrates that the selectivity in the hydrogenation of acrolein is controlled by the relative rates of acrolein partial hydrogenation to oxopropyl surface species and of acrolein decomposition, which has significant implications for rational catalyst design.     

Development of Palladium Surface‐Enriched Heteronuclear Au–Pd Nanoparticle Dehalogenation Catalysts in an Ionic Liquid

Heteronuclear Au–Pd nanoparticles were prepared and immobilized in the functionalized ionic liquid [C₂OHmim][NTf₂]. The structural and electronic properties of the nanoparticles were characterized by a range of techniques and the surface of the nanoparticles was found to be enriched in Pd. Moreover, the extent of Pd enrichment is easily controlled by varying the ratio of Au and Pd salts used in the synthesis. The heteronuclear nanoparticles were found to be effective catalysts in dehalogenation reactions with no activity observed for the pure Au nanoparticles and only limited activity for the pure Pd nanoparticles. The activity of the heteronuclear nanoparticles may be attributed to charge transfer from Pd to Au and consequently to more efficient reductive elimination.     

An improved preparation of mesoporous silica‐supported Pd as sustainable catalysts for phosphine‐free Suzuki–Miyaura and Heck coupling reactions

An improved and eco‐friendly procedure has been developed to generate mesoporous silica‐supported palladium nanoparticles (SiO₂@PdNP) that could be used as a sustainable heterogeneous Pd catalyst for phosphine‐free Suzuki–Miyaura and Heck coupling reactions with excellent turnover number and turnover frequency. The presence of Pd on the silica surface was detected by X‐ray diffraction and the structural morphology of SiO₂@PdNP was obtained by transmission electron microscopy. The heterogeneous catalytic system is recyclable and leaching of the metal after the reaction is not apparently observed. Copyright © 2013 John Wiley & Sons, Ltd.     

高效组合型 Pd/C 催化剂用于 Suzuki 偶联反应

 采用有机金属 Pd2(dba)3 (dba 为二亚苄基丙酮) 还原分解法制得均匀分布的 Pd 纳米颗粒 (粒径为 3~6 nm) 混合液, 并用活性炭直接吸附得到了组合型 Pd/C 纳米催化剂. 采用透射电子显微镜、X 射线光电子能谱和 X 射线衍射等手段测定了催化剂表面 Pd 颗粒大小分布、晶型和化学态等. 将该催化剂用于 Suzuki 碳-碳偶联反应, 其催化活性比浸渍法制备的 Pd/C 催化剂高 2 倍以上. 以溴代芳烃为底物时, 在 80 oC 下 0.5 h 后偶联产物收率可达 98% 以上. 以邻氯硝基苯为底物时, 在 110 oC 下 1 h 后偶联产物收率可达 64%; 延长反应时间, 产物收率可达 90% 以上.     

Palladium–cadmium sulfide nanopowder at oil–water interface as an effective catalyst for Suzuki–Miyaura reactions

A simple and effective strategy is described for the synthesis of Pd–CdS nanopowder by the reduction of an organopalladium(II) complex, [PdCl₂(cod)] (cod = cis ,cis ‐1,5‐cyclooctadiene), in the presence of CdS quantum dots (QDs) at a toluene–water interface. We investigated the impact of addition of CdS QDs on catalytic activity of Pd nanoparticles (NPs). The Pd–CdS nanopowder functions as an efficient catalyst for Suzuki–Miyaura reactions for the formation of carbon–carbon bonds. There is a high electron density on Pd NPs and due to their high electron affinity they behave as an electron scavenger from CdS increasing the rate of oxidative addition, which is the rate‐determining step of the catalytic cycle, and, just as we expect, the C─C coupling reaction with the Pd–CdS nanopowder is faster and occurs in less time than that with Pd nanocatalysts. Compared to classical reactions, this method consistently has the advantages of short reaction times, high yields in a green solvent, reusability of the catalyst without considerable loss of catalytic activity and low cost, and is a facile method for the preparation of the catalyst.     

An efficient and recyclable water-soluble cyclopalladated complex for aqueous Suzuki reactions under aerial conditions

Several water-soluble cyclopalladated complexes with five- or six-membered rings have been prepared as air-stable solids from Schiff base ligands bearing an N-phenyl sulfonate groups. Cyclopalladated complexes with six-membered rings show high catalytic efficiency for the Suzuki reactions of aryl bromides with phenylboronic acid in aqueous solvents under mild conditions. Palladium complex 1 can be used for five reaction cycles in high conversions for the Suzuki reactions in neat water without additives. The catalytic process for the Suzuki couplings is proved by TEM analysis to proceed on Pd(0) nanoparticles. Surfactant-protected palladium nanoparticles present lower activities and poorer recyclability for the coupling reactions than those generated in situ without additives.     

Fe3O4‐SAHPG‐Pd0 nanoparticles: A ligand‐free and low Pd loading quasiheterogeneous catalyst active for mild Suzuki–Miyaura coupling and C?H activation of pyrimidine cores

This paper reports a green magnetic quasiheterogeneous efficient palladium catalyst in which Pd⁰ nanoparticles have been immobilized in self‐assembled hyperbranched polyglycidole (SAHPG)‐coated magnetic Fe₃O₄ nanoparticles (Fe₃O₄‐SAHPG‐Pd⁰). This catalyst has been used for effective ligandless Pd catalyzed Suzuki–Miyaura coupling reactions of different aryl halides with substituted boronic acids at room temperature and in aqueous media. Herein, SAHPG is used as support; it also acts as a reducing agent and stabilizer to promote the transformation of Pd^II to Pd⁰ nanoparticles. Also, this environmental friendly quasiheterogeneous catalyst is employed for the first time in the synthesis of new pyrimido[4,5‐b]indoles via oxidative addition/C? H activation reactions on the pyrimidine rings, which were obtained with higher yield and faster than when Pd(OAc)₂ was used as the catalyst. Interestingly, the above‐mentioned catalyst could be recovered in a facile manner from the reaction mixture by applying an external magnet device and recycled several times with no significant decrease in the catalytic activity.     

Formation of palladium nanoparticles in olefin oxidation with iron(III) aqua ions in the presence of the Pd/ZrO2/SO4 metallic catalyst

The reactions of the Pd/ZrO₂/SO₄-catalyzed oxidation of ethylene, propene, and but-1-ene in a 0.1–1.5 M solution of perchloric acid with iron(III) aqua ions to carbonyl compounds, viz., acetaldehyde, acetone, and methyl ethyl ketone, respectively, were studied. The formation of palladium nanoparticles (5 nm) in solution on contact of the initial heterogeneous Pd/ZrO₂/SO₄ catalyst with perchloric acid was proved by transmission electron microscopy. The palladium nanoparticles are assumed to play the key role in olefin oxidation with the iron(III) aqua ions. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 4, pp. 627–632, April, 2006.     

Anchored complexes of Ni,Pt, and Pd on Fe3O4 nanoparticles as new and eco-friendly nanocatalysts in Suzuki and Heck coupling reactions

Abstract

Three recoverable nanocatalysts were developed by immobilizing Ni, Pt, and Pd Schiff-base complexes on the magnetite nanoparticles. Successful preparation of the nanocatalysts was evidenced by Fourier transform infrared (FT-IR) and energy dispersive X-ray (EDX) spectroscopy. Nano-sized spherical structure of the nanocatalysts was indicated by scanning electron microscopy (SEM). X-ray powder diffraction (XRD) determined that the crystalline cubic spinel structure of Fe₃O₄ remained constant through the synthesis of three complexes on Fe₃O₄ nanoparticles. Magnetic properties of the nanocatalysts were analyzed by the vibration sample magnetometer (VSM). Thermostability of the nanocatalysts was studied by thermogravimetric analysis (TGA). Metal loading of these nanocatalysts was evidenced by inductively coupled plasma atomic emission (ICP-AES).

Investigating the catalytic activity of these nanocatalysts in Suzuki and Heck reactions implicated that in the presence of Pd nanocatalyst coupling reactions proceeded efficiently. For Pt nanocatalyst, Suzuki reaction took place in longer time with moderate to good yield. For the Heck reaction, the desired products were achieved only for aryl iodide and some aryl bromides. The Ni nanocatalyst could just catalyze the Suzuki reaction.

Relying on the magnetic characteristic, these nanocatalysts could be simply recovered and reused several cycles without significant loss in catalytic activity.     

Graphene-supported small-sized palladium nanoparticles made by facile photochemical approaches

To achieve small-sized and well-dispersed palladium (Pd) nanoparticles, we make use of effective photochemical approaches to synthesis of clean Pd nanoparticles on the surface of graphene at room temperature. By modulating the photochemical reaction conditions, the size and dispersion of graphene–Pd composites can be well controlled, where PdCl₄²⁻ and graphene oxide (GO) are the reaction precursors, Hantzsch 1,4-dihydropyridine (HEH) is used as an electron donor and an amine-type ligand to stabilize small Pd nanoparticles on the surface of graphene. As a result, the easy and effective photochemical approaches to the graphene–Pd composites with well-dispersed, small-sized Pd nanoparticles and highly conductive reduced GO, are established. Good to excellent yields have also been achieved with the graphene-supported Pd nanoparticles catalysts for the Suzuki coupling reaction.     

Pd embedded N,S co‐doped graphene wrapped core‐shell magnetic nanospheres: Engineered stable nanocatalyst for Suzuki couplings

Designed nitrogen and sulfur co‐doped graphene wrapped magnetic core‐shell supported Pd nanoparticles were synthesized through the following steps. Firstly, Fe₃O₄ was prepared, coated with silica and then functionalized with amine groups to create a positive charge on the structure for enhancing the interaction of the Fe₃O₄@SiO₂ with graphene oxide. Secondary, the pre‐catalyst wrapped with graphene to enhance adsorption of aromatic substrates through π–π stacking. Thirdly, graphene was doped with nitrogen and sulfur to increase the grafting of Pd in hybrid. Finally, Pd NPs were attached on the surface of pre‐engineered structure to produce Fe₃O₄@SiO₂@N,S‐wG@Pd which exhibited high performance in Suzuki reactions. This superior activity can be indexed to the incorporation of N and S atoms into graphene led to high anchoring and well‐dispersion of Pd NPs on the nanocomposite surface offering large amounts of active centers, that strongly increased the interaction between Pd and substrates to decreases Pd leaching.     

Immobilization of palladium nanoparticles on ionic liquid-triethylammonium chloride functionalized magnetic nanoparticles: As a magnetically separable,stable and recyclable catalyst for Suzuki-Miyaura cross-coupling reactions

A facile procedure was applied to successfully synthesize novel Pd nanoparticles immobilized on triethanolamine-functionalized magnetic nanoparticles [Fe₃O₄/IL/Pd]. Diverse characterizations (HR-TEM, XRD, FT-IR, TGA, EDX, FE-SEM, ICP, XPS and VSM) were carried out to identify intrinsic traits of the nanoparticles. At room temperature, Fe₃O₄/IL/Pd demonstrated high catalytic activity toward Suzuki-Miyaura cross-coupling reactions in aqueous solution. Based on the results, Fe₃O₄/IL/Pd acted as zwitterionic IL-type heterogeneous catalyst, which could be separated from the reaction mixture, conveniently. Moreover, it exhibited excellent recyclability for at least eight cycles without considerable loss of its activity.     

Palladium nanoparticles immobilized on cyclodextrin‐decorated halloysite nanotubes: Efficient heterogeneous catalyst for promoting copper‐ and ligand‐free Sonogashira reaction in water–ethanol mixture

Combining the excellent features of halloysite nanoclay and cyclodextrin, a novel hybrid system was designed and synthesized based on covalent attachment of tosylated cyclodextrin to thiosemicarbazide‐functionalized halloysite nanoclay and used for the immobilization of Pd nanoparticles. The resulting hybrid, Pd@HNTs‐T‐CD, was then characterized using various techniques, and successfully used for promoting copper‐ and ligand‐free Sonogashira coupling reactions of halobenzenes and acetylenes in a mixture of water and ethanol. Notably, under Pd@HNTs‐T‐CD catalysis, the reaction could proceed in relatively short reaction time to furnish the corresponding products in high yields. Additionally, the catalyst was recyclable and could be simply recovered and reused for several reaction runs. Results also established negligible leaching of Pd, indicating the efficiency of HNTs‐T‐CD for embedding Pd nanoparticles.