Effect of La2O3 on Catalytic Performance of Au/TiO2 for CO Oxidation

Pure TiO₂ and La-doped TiO₂ were prepared by the sol-gel method. Au was supported on TiO₂ by the deposition-precipitation (DP) method, and its catalytic activity for CO oxidation was tested. The results showed that doping La in Au/TiO₂ could improve its catalytic activity obviously for CO oxidation. The analyses of X-ray diffraction (XRD), temperature-programmed desorption (TPD), and Brunauer-Emmett-Teller (BET) surface area further showed that the presence of La in TiO₂ not only increased its surface area and restrained the growth of TiO₂ crystallites, but could also enhance the microstrain of TiO₂. In terms of O₂-TPD, a new adsorbed species O⁻ appeared on the surface of La-doped TiO₂. The results of in-situ Fourier transform-infrared (FT-IR) spectroscopy illustrated that the high activity of Au/La₂O₃-TiO₂ was attributed to the presence of La promoting the reactivity of CO adsorbed on the Au site and the formation of the second active site on the surface of TiO₂     

g-C3N4/Bi2O2CO32D纳米片复合材料的制备及可见光催化性能研究

采用自组装和化学沉淀法分别制得两种可见光驱动复合材料石墨相氮化碳/碳酸氧铋(g-C_3N_4/Bi_2O_2CO_3).采用X射线衍射光谱(XRD),紫外可见光谱、扫描电镜(SEM)、N_2吸附、电化学阻抗谱(EIS)和X射线光电子能谱(XPS)等分析手段对制备的催化剂进行了表征.结果表明,制备方法对纳米复合材料的晶相、形态及光学性能没有影响,但是影响g-C_3N_4和Bi_2O_2CO_3之间的相互作用力,导致光生电子-空穴对的分离速率存在显著差异.以可见光驱动苯酚和罗丹明B的降解实验为探针反应检测催化剂的光催化性能.实验结果表明自组装法得到的异质结催化剂中相互作用力更强,催化效果最高.O_2-是罗丹明B降解反应的主要活性物种,染料的光敏化、Bi_2O_2CO_3与g-C_3N_4综合效应,导致光生载流子电荷分离效率更高.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

Cr2(WO4)3和Cr2(MoO4)3的负热膨胀特性研究

用液相反应-前驱物烧结法制备了Cr₂(WO₄)₃和Cr₂(MoO₄)₃粉体。298～1 073 K的原位粉末X射线衍射数据表明Cr₂(WO₄)₃和Cr₂(MoO₄)₃的晶胞体积随温度的升高而增大, 本征线热膨胀系数分别为(1.274±0.003)×10^-6 K^-1和(1.612±0.003)×10^-6 K^-1。用热膨胀仪研究了Cr₂(WO₄)₃和Cr₂(MoO₄)₃在静态空气中298～1 073 K范围内热膨胀行为，即开始表现为正热膨胀，随后在相转变点达到最大值，最后表现为负热膨胀，其负热膨胀系数分别为(-7.033±0.014)×10^-6 K^-1和(-9.282±0.019)×10^-6 K^-1。     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Synthesis and properties of the double perovskites La2NiVO6, La2CoVO6, and La2CoTiO6

The double perovskites La₂CoVO₆, La₂CoTiO₆, and La₂NiVO₆, are described. Rietveld fitting of neutron and powder X-ray diffraction data show La₂NiVO₆ and La₂CoVO₆ to have a disordered arrangement of B-cations whereas La₂CoTiO₆ shows ordering of the B-cations (with ∼5% Co/Ti inversion). Curie-Weiss fits to the linear region of the 1/χ plots reveal Weiss temperatures of −107, −34.8, and 16.3 K for La₂CoVO₆, La₂CoTiO₆, and La₂NiVO₆, respectively, and magnetic transitions are observed. La₂CoTiO₆ prepared by our method differs from material prepared by lower-temperature routes. A simple antiferromagnetic spin model is consistent with the data for La₂CoTiO₆. These compounds are semiconductors with bandgaps of 0.41 (La₂CoVO₆), 1.02 (La₂CoTiO₆) and 0.45 eV (La₂NiVO₆).     

Energetics of copper diphosphates – Cu2P2O7 and Cu3(P2O6OH)2

Differential scanning calorimetry and high temperature oxide melt solution calorimetry are used to study enthalpy of phase transition and enthalpies of formation of Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂. α-Cu₂P₂O₇ is reversibly transformed to β-Cu₂P₂O₇ at 338–363 K with an enthalpy of phase transition of 0.15 ± 0.03 kJ mol⁻¹. Enthalpies of formation from oxides of α-Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂ are −279.0 ± 1.4 kJ mol⁻¹ and −538.8 ± 2.7 kJ mol⁻¹, and their standard enthalpies of formation (enthalpy of formation from elements) are −2096.1 ± 4.3 kJ mol⁻¹ and −4302.7 ± 6.7 kJ mol⁻¹, respectively. The presence of hydrogen in diphosphate groups changes the geometry of Cu(II) and decreases acid–base interaction between oxide components in Cu₃(P₂O₆OH)₂, thus decreasing its thermodynamic stability.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

XAFS characterization of supported PdCl2?CuCl2 catalysts for CO oxidation

A heterogenized Wacker catalyst system in which pores of a high surface area alumina were filled with an aqueous solution of PdCl₂–CuCl₂ was active for the oxidation of CO near room temperature. The structure of thecatalyst was studied by XRD and XAFS. The active phase of Pd was a molecular Pd species whose structure was similar to PdCl₂, probably modified by a carbonyl ligand. The active phase of copper was found to be solid Cu₂Cl(OH)₃ particles. The presence of Cu was essential to keep the Pd in the Pd(II) state during the reaction.     

Spectroscopic properties of guanidinium zinc sulphate [C(NH2)3]2Zn(SO4)2 and ab initio calculations of [C(NH2)3]2 and HC(NH2)3

Raman and FTIR spectra of guanidinium zinc sulphate [C(NH₂)₃]₂Zn(SO₄)₂ are recorded and the spectral bands assignment is carried out in terms of the fundamental modes of vibration of the guanidinium cations and sulphate anions. The analysis of the spectrum reveals distorted SO₄²⁻ tetrahedra with distinct S–O bonds. The distortion of the sulphate tetrahedra is attributed to Zn–O–S–O–Zn bridging in the structure as well as hydrogen bonding. The CN₃ group is planar which is expressed in the twofold symmetry along the C–N (1) vector. Spectral studies also reveal the presence of hydrogen bonds in the sample. The vibrational frequencies of [C(NH₂)₃]₂ and HC(NH₂)₃ are computed using Gaussian 03 with HF/6-31G* as basis set.     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

Acidic properties of V2O5-WO3/ZrO2 catalysts

The adsorption of pyridine on V₂O₅−WO₃/ZrO₂ has been studied by FTIR. In V₂O₅/ZrO₂ (2 wt.%), the number of both Br?nsted and Lewis acidic sites increased with the addition of WO₃, while in V₂O₅/ZrO₂ (5 wt.%), Br?nsted sites increased and Lewis sites did not change.     

Preparation and photocatalytic activity of Sb2S3/Bi2S3 doped TiO2 from complex precursor via gel-hydrothermal treatment

Sb₂S₃/Bi₂S₃ doped TiO₂ were prepared with the coordination compounds [M(S₂CNEt)₃] (M=Sb, Bi; S₂CNEt=pyrrolidinedithiocarbamate) as precursors via gel-hydrothermal techniques. The doped TiO₂ were characterized by XRD, SEM, XPS and UV-vis diffuse reflectance means. The photocatalyst based on doped TiO₂ for photodecolorization of 4-nitrophenol (4-NP) was examined. The optimal Bi₂S₃/Sb₂S₃ content, pH and different doped techniques have been investigated. Photocatalytic tests reveal that M₂S₃ doped TiO₂ via the gel-hydrothermal route performs better photocatalytic activity for photodegradation reaction of 4-nitrophenol (4-NP).     

A Structural Investigation of La2(GeO4)O and Alkaline-Earth-Doped La9.33(GeO4)6O2

The structures of the oxyorthogermanate La₂(GeO₄)O and the apatite-structured La_9.33(GeO₄)₆O₂ have been refined from powder neutron diffraction data. La₂(GeO₄)O crystallizes in a monoclinic unit cell (P2₁/c) and is cation stoichiometric in contrast to previous reports. La_9.33(GeO₄)₆O₂ crystallizes in a hexagonal unit cell (P6₃/m) and the powder diffraction data show anisotropic peak broadening that is observed in electron diffraction patterns as incommensurate diffuse spots at hkq reciprocal planes (with q=1.6-1.7) and can be attributed to a correlated disorder in the “apatite channels”. This compound was doped up to a nominal composition close to M₂La₈(GeO₄)₆O₂ with M=Ca, Sr, Ba. The dopant ions preferentially occupy the 4f sites as the number of La vacancies decreases. The measured ionic conductivity of La_9.33(GeO₄)₆O₂ is about 3 orders of magnitude larger than for La₂(GeO₄)O at high temperatures and decreases with increasing dopant content from the highest value of about 0.16 S cm⁻¹ at 1160 K.     

Vibrational spectra of the peroxotantalates (NH4)3[Ta(O2)4], K3[Ta(O2)4], Rb3[Ta(O2)4] and Cs3[Ta(O2)4] and the crystal structure of Rb3[Ta(O2)4]

The compounds (NH₄)₃[Ta(O₂)₄], K₃[Ta(O₂)₄], Rb₃[Ta(O₂)₄] and Cs₃[Ta(O₂)₄] have been prepared and investigated by X-ray powder methods as well as Raman- and IR-spectroscopy. In the case of Rb₃[Ta(O₂)₄] the structure has been solved from single crystal data. It is shown that all these compounds are isotypic and crystallize in the K₃[Cr(O₂)₄] type (SG , No. 121). The infrared- and Raman spectra (recorded on powdered samples) are discussed with respect to the internal vibrations of the peroxo-group and the dodecahedral [Ta(O₂)₄]³⁻ ion. Symmetry coordinates for the [Ta(O₂)₄]³⁻ ion are given from which the vibrational modes of the O-O stretching vibrations of the O₂²⁻ groups, the Ta-O stretching vibrations and the Ta-O bending vibrations are deduced.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

Synthesis and nonlinear optical properties of BaTi(BO3)2 and Ba3Ti3O6(BO3)2 crystals in glasses with high TiO2 contents

The ternary BaO-TiO₂-B₂O₃ glasses containing a large amount of TiO₂ (20-40 mol%) are prepared, and their optical basicities (Λ), the formation, structural features and second-order optical nonlinearities of BaTi(BO₃)₂ and Ba₃Ti₃O₆(BO₃)₂ crystals are examined to develop new nonlinear optical materials. It is found that the glasses with high TiO₂ contents of 30-40 mol% show large optical basicities of Λ=0.81-0.87, suggesting the high polarizabity of TiO_n polyhedra (n=4-6) in the glasses. BaTi(BO₃)₂ and Ba₃Ti₃O₆(BO₃)₂ crystals are found to be formed as main crystalline phases in the glasses. It is found that BaTi(BO₃)₂ crystals tend to orient at the surface of crystallized glasses. The new XRD pattern for the Ba₃Ti₃O₆(BO₃)₂ phase is proposed through Rietvelt analysis. The second harmonic intensities of crystallized glasses were found to be 0.8 times as large as α-quartz powders, i.e., I^2ω(sample)/I^2ω(α-quartz)=0.8, for the sample with BaTi(BO₃)₂ crystals and to be I^2ω(sample)/I^2ω(α-quartz)=68 for the sample with Ba₃Ti₃O₆(BO₃)₂ crystals. The Raman scattering spectra for these two crystalline phases are measured for the first time and their structural features are discussed.     

(ZrO2)0.86(Sm2O3)0.14纳米粉体的水热法合成及其烧结体的电性能

以湿化学法制得Zr(OH)₄和Sm(OH)₃的共沉淀为前驱体, 在碱性介质中用水热法合成了(ZrO₂)_0.86(Sm₂O₃)_0.14及(ZrO₂)_0.88(Sm₂O₃)_0.12纳米粉体. 将纳米粉体在较低温度(1450 ℃)下烧结制得了致密的固体电解质陶瓷样品, 比通常高温固相反应法采用的烧结温度(＞1600 ℃)降低了150 ℃以上. XRD测定结果表明, (ZrO₂)_0.86(Sm₂O₃)_0.14纳米粉体及其烧结体均为立方相, 但(ZrO₂)_0.88(Sm₂O₃)_0.12纳米粉体为立方相, 它的烧结体为立方相和单斜相的混合相. 用交流阻抗谱法、氧浓差电池法及氧泵(氧的电化学透过)法研究了(ZrO₂)_0.86(Sm₂O₃)_0.14陶瓷样品在600～1000 ℃下的离子导电特性. 结果表明, 该陶瓷样品在600～1000 ℃下氧离子迁移数为1, 氧离子电导率的最大值为3.2×10^－2 S•cm^－1, 是一个优良的氧离子导体; 它的氧泵性能明显地优于YSZ.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.