低温热氧化法制备Bi_2Mo_3O_(12)介质薄膜

通过直流磁控溅射法在Si/Si O_2/Pt基片表面沉积摩尔比为2∶3的Bi/Mo多层薄膜。系统研究了热氧化温度对上述薄膜的物相组成、微观形貌、介电性能的影响。X-射线衍射(XRD)数据表明,420~480℃可热氧化形成介质薄膜。420℃氧化,薄膜的物相为Bi_2O_3、Mo O_3、Bi_2Mo O_6和Bi_2Mo_3O_(12);450℃和480℃氧化,薄膜的主相均为Bi_2Mo_3O_(12),另有少量Bi_2Mo O_6存在。扫描电镜(SEM)观察结果显示,薄膜在450℃即已致密、均匀。介电性能测试结果显示,480℃氧化的介质薄膜,具有较优的介电性能:1 k Hz测量,介电常数约15.6,介电损耗约0.65%;5.55 k V/mm电场强度下,漏电流密度约3.4×10~(-7) A/mm~2。考虑到Bi/Mo薄膜极低的成膜温度(480℃)及直流磁控溅射Bi/Mo金属薄膜较大的沉积速率(92 nm/min),直流磁控溅射Bi/Mo金属薄膜,然后热氧化成Bi_2Mo_3O_(12)介质薄膜,在工业上具有应用价值,有望应用于嵌入式薄膜电容器的制备。     

(ZrO2)0.86(Sm2O3)0.14纳米粉体的水热法合成及其烧结体的电性能

以湿化学法制得Zr(OH)4和Sm(OH)3的共沉淀为前驱体,在碱性介质中用水热法合成了(ZrO2)0.86(sm2O3)014及(ZrO2)0.88(Sm2O3)0.12纳米粉体.将纳米粉体在较低温度(1450℃)下烧结制得了致密的固体电解质陶瓷样品,比通常高温固相反应法采用的烧结温度(＞1600℃)降低了150℃以上.XRD测定结果表明,(ZrO2)0.86(Sm2O3)0.14纳米粉体及其烧结体均为立方相,但(ZrO2)0.88(Sm2O3)0.12纳米粉体为立方相,它的烧结体为立方相和单斜相的混合相.用交流阻抗谱法、氧浓差电池法及氧泵(氧的电化学透过)法研究了(ZrO2)0.86(Sm2O3)0.14陶瓷样品在600～1000℃下的离子导电特性.结果表明,该陶瓷样品在600～1000℃下氧离子迁移数为1,氧离子电导率的最大值为3.2×10-2 S·cm-1,是一个优良的氧离子导体;它的氧泵性能明显地优于YSZ.     

聚合物前驱体法制备立方相WO_3薄膜的光电化学性质

以(NH4)6W7O24·6H2O为钨源,聚乙二醇1000(PEG 1000)为配位聚合物,采用聚合物前驱体法制备了WO3薄膜,利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见(UV-Vis)吸收光谱等手段对其结构进行表征.采用循环伏安法、Mott-Schottky测试、瞬态光和稳态光电流谱等方法研究了WO3薄膜电极的光电化学性能.结果表明,制备的WO3薄膜为立方晶系,禁带宽度约为2.7eV.当热处理温度为450℃时,载流子浓度达到最大2.44×1022cm-3,平带电位为0.06V,在500W氙灯光源照射和1.2V偏压下,光电流密度为2.70mA·cm-2.进一步探讨了热处理温度对其光电性质的影响及其机理.     

甘油-DMSO-H2O中阳极氧化TiO2纳米管阵列的生长与性能

采用NH4F-甘油-DMSO(二甲基亚砜)-H2O溶液体系的电化学阳极氧化法, 在金属钛基板上形成厚度为0.4-1.5 μm的有序TiO2纳米管阵列薄膜. 利用场发射电子扫描显微镜(FESEM)技术, 研究了电解液的组成及阳极氧化电压对TiO2纳米管阵列生长形貌的影响. 结果表明, 阳极氧化电压可以影响TiO2纳米管的径向尺寸和长度；通过改变电解液中DMSO/H2O的体积比, 能够调控纳米管的生成速率与形貌. 利用X射线衍射(XRD)对经过不同温度热处理的TiO2纳米管阵列薄膜的物相进行了分析. TiO2纳米管阵列薄膜的光电催化分解水过程的电压-电流特性测量显示, 光电流密度大于0.2 mA·cm-2.     

金属材料分析方法的选择和施行第六讲金属材料中稀土元素的测定(续)

1.5镧系元素的物理性质1.5.1镧系元素的晶体构型镧、铈、镨三元素是具有六方密堆积(h.c.p.)和立方密堆积(c.c.p.)晶型的双晶形金属,元素钪是面心立方(f.c.c.)和六方密堆积晶型的双晶形金属,钐是斜方六面体晶形,铕是体心立方晶形,镱是面心立方晶形,其余稀土金属都是六方密堆积晶形。稀土金属大都具有同素异晶的构型,由于晶型的转变,使其与其它金属的作用复杂化。钕的熔点为1 016℃,但以前曾把它由六方晶系向体心六立晶系转变的温度(840℃)误作为该金属的熔点。1.5.2镧系元素的密度钪的密度为2.99 g·cm-3和钇的密度为4.47 g·cm-3。其余元素…     

单一混合固态源PE-MOCVD法制备YSZ薄膜及其表征

采用等离子体增强的MOCVD技术,以均匀混合的金属β-二酮鳌合物固态源Y(DPM)₃和Zr(DPM)₄作为前驱物,在NiO/SDC多孔阳极和多孔-αAl₂O₃衬底上制备了氧化钇稳定的氧化锆(YSZ)薄膜.研究了两种衬底对成膜过程和膜的结构以及微结构的影响,讨论了源区输运机制及薄膜生长动力学.XPS分析结果表明,薄膜中Y和Zr元素的摩尔比低于原始混合源中的Y和Zr元素的摩尔比,当混合源中的Y和Zr元素的摩尔比约为0.35:1时,可以获得无定形态的8%YSZ薄膜,经高温焙烧转化为单一立方相,其晶粒大小约为100nm,薄膜的生长速率约为7nm/min.     

Ce_(0.8)Nd_(0.2)O_(1.9)-La_(0.95)Sr_(0.05)Ga_(0.9)Mg_(0.1)O_(3-δ)固体复合电解质的结构和电性能

采用溶胶-凝胶法分别制备La0.95Sr0.05Ga0.9Mg0.1O3-δ(LSGM)和Ce0.8Nd0.2O1.9(NDC)电解质,并在NDC溶胶中加入0-15%(w,质量分数)的LSGM预烧粉体制得NDC-LSGM复合电解质,研究不同质量比复合电解质的结构和电性能.采用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)和X能量色散谱仪(EDS)对样品进行结构表征,交流(AC)阻抗谱测试样品导电性能.结果表明:NDC-LSGM复合体系主要由立方萤石结构相、钙钛矿结构相和杂质相组成;LSGM的添加可促进晶粒的生长,产生大量相界面,清除或降低SiO2有害影响,明显提高晶界导电性;LSGM质量分数为10%的样品NL10具有最高晶界电导率和总电导率,400°C时NL10的晶界电导率σgb和总电导率σt分别为12.15×10-4和3.49×10-4S cm-1,与NDC的σgb(1.41×10-4S cm-1)和σt(1.20×10-4S cm-1)相比分别提高了7.62和1.91倍,总电导率的提高主要归因于晶界电导率的影响.     

La0.5>RE0.3Sr0.2FeO3－δ (RE = Nd、Ce、Sm)体系双稀土阴极材料的制备与电性能

采用甘氨酸-硝酸盐法(GNP)合成了La0.5RE0.3Sr0.2FeO3－δ(RE=Nd、Ce、Sm)系列复合氧化物粉体. 用X射线衍射(XRD)和TG-DSC分析了样品钙钛矿物相的形成过程, 用Archimedes排水法测量体积密度并计算烧结样品的相对密度, 用四端子技术测量电导率. 结果显示, 掺Nd的样品1200 ℃烧结2 h成为单一立方钙钛矿结构, 掺Ce样品有明显的CeO2立方相析出, 掺Sm样品主相为钙钛矿结构伴有微弱的杂峰. 1250 ℃烧结2 h的La0.5Nd0.3Sr0.2FeO3－δ在600 ℃时电导率高达100 S•cm-1以上, 明显高于La0.5Ce0.3Sr0.2FeO3－δ及La0.5Sm0.3Sr0.2FeO3－δ样品的电导率, 预示着La0.5Nd0.3Sr0.2FeO3－δ可能是一种良好的中温固体氧化物燃料电池(SOFC)阴极材料.     

均匀电场对冰晶结构及生长的影响（英文）

采用分子动力学模拟方法研究了强度为4.0-40.0 V·nm-1的均匀电场对过冷水冰晶结构和冰晶生长速率的影响.文中通过CHILL算法来识别不同的冰相结构,通过拟合Avrami公式来得到冰晶生长所需的特征时间.结果表明,在所施加的电场强度范围内生成的冰相以立方冰为主.随着电场强度的增加,形成的立方冰的变形程度逐渐增大,冰晶的密度从0.98 g·cm-3增加到1.08 g·cm-3,同时冰晶生长的特征时间从5.153 ns减小到0.254 ns,冰晶生长的速率逐渐增长.对水分子的动力学分析表明,冰晶生长速率增加的部分原因是电场能够促进水分子运动到形成冰晶所需要的取向.此外,对冰相分子形成过程的分析表明缺陷冰分子在冰晶的生长过程中扮演着中间态的角色.随电场强度的增加,由缺陷冰转变为立方冰的比例增长的速率逐渐提高.     

Ba_(1-x)Ca_xZr_(0.2)Ti_(0.8)O_3陶瓷的微观结构、相变与介电性质（英文）

采用传统的水热合成法和烧结过程制备了Ba_(1-x)Ca_xZr_(0.2)Ti_(0.8)O_3(BCZT,x=0.1,0.2,0.3)陶瓷.研究了Ca~(2+)含量对其相组成、微观结构和介电性质所产生的影响.结果表明当x=0.3时,出现了不纯相.随着Ca~(2+)含量的增加,BCZT陶瓷的形貌从平板状转化为不规则的立方体状.介电常数曲线显示为大而宽的峰,其峰值出现在约66℃.从介电损耗曲线可以观察到随着烧结温度的增加,出现了斜方相至四方相(T_(O-T))和四方相至立方相(T_(T-C))的多晶相变.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.