Multielemental fast analysis of vegetation samples by wavelength dispersive X-ray fluorescence spectrometry: Possibilities and drawbacks

X-ray fluorescence spectroscopy (XRF) is universally recognized as a non-destructive method for rapid and sequential, or simultaneous analysis of elemental composition of a material. The use of this technique for the direct determination of chemical elements in plant matrices has increased over the last few years.In the present study, a wavelength dispersive X-ray fluorescence (WDXRF) method for the quantitative analysis of some major elements (Na, Mg, Al, P, S, K, Ca), trace elements (Mn, Fe, Co, Zn, As) and non-essential elements (Sr, Pb) in vegetation specimens has been developed. The method uses a quick and easy sample preparation procedure since only drying, pulverizing and pressing of the samples are necessary. The calibration procedure was established by employing four plant reference materials and several synthetic cellulose calibrators spiked with appropriate amounts of analytes. Matrix effects were corrected employing the method of the influence coefficients on the basis of the computerized routine program linked to the equipment.Trueness of the experimental procedure was checked by using the standard reference material GBW07602 “Bush branches and leaves”. In general, good agreement was achieved between certified values and the measured ones with recoveries ranging from 94% to 107%. Moreover, quality parameters, including repeatability and reproducibility of the developed method, were also evaluated.On the whole, from results obtained, WDXRF method proposed prove to be good and effective tool for environmental investigation and quality control processes in vegetation specimens.     

Surface contamination effects on leaf chemical composition in the Atlantic Forest

Summary The exogenous material that adheres to the leaf surface affects the elemental composition of the plant itself, thereby constituting one of the major error sources in plant analysis. The present work investigated the surface contamination of leaves from the Atlantic Forest. Instrumental neutron activation analysis (INAA) was applied to assess the efficiency of leaf EDTA-washing. Chemical element concentrations were corrected using Sc (soil tracer) since resuspended soil is the main source of contamination in leaves. As a result, EDTA-washing should be used mainly for the evaluation of terrigenous elements, while the Sc-corrected concentrations are considered satisfactory for the other elements.     

21种桉叶微量元素含量测定及其意义

首次报道广东海康金星农场栽培的21种桉叶的微量元素含量和测定方法。结果认为：桉叶中含有Zn、Cu、Fe、Ca、Mn、Mg等人体必需的微量元素，其中Fe和Mn的含0量比其它微量元素高出3～4个热量级，而Fe和Mn是人体需要的微量元素，桉叶是富Fe、Mn的植物资源，它作为中药和动物鰕料添加剂是适合的。     

Elemental uptake of radish grown near a Municipal Solid Waste dumping site by EDXRF

Radish plant was collected along with root and soil from the nearby area of a Municipal Solid Waste dumping site of the metropolitan city of Kolkata, West Bengal, India and analyzed for a wide range of elements using the EDXRF technique with a ¹⁰⁹Cd point source and a Si(Li) detector. The samples comprized of the root-soil, root and leaves. For quality control purposes, NIST standard reference material (SRM) 1648 Urban Particulate Matter had also been analyzed using the same procedure as for the samples. Concentrations of elements with X-ray energies in the range of 3–20 keV in the soil around the root and their uptake pattern by the root and the leaves have been estimated.     

The use of reference materials in the fossil fuels quality control

The determination of trace elements in fossil fuels is of primary importance to achieve correct evaluation of environmental impact of power plants. The characterization of coals and fuel oils can be carried out by several analytical techniques such as ICP-MS, FI-HG-AAS, ETA-AAS, ICP-AES and XRF. The accuracy of the analysis, done to routine basis, can be systematically checked by means of the reference materials available or comparing the results obtained by different techniques. Quality control activities in the field of trace element determination in fossil fuels (coal and fuel oil) are described. The determination of As, Hg and Se in coals was carried out by different techniques (NAA, FI-HG-AAS and FI-ICP-MS) together with the determination of several trace metals in residual fuel oils by NAA, ETA-AAS and ICP-MS. The use of certified reference materials in order to check the accuracy of procedures is discussed and the results obtained for NIST 1632a and NIST 1632b (coal samples) and NIST 1634b and NIST 1619 (fuel oil samples) are reported.     

Trace element XRF analysis of Mongolian coals

X-ray fluorescence has been applied as an analytical technique for the trace element characterization of Mongolian coals. Coal, samples from five regions of Mongolia are found to contain variable amounts of many trace elements. Various approaches to quantitative XRF analysis including a simple quantitative method, an emission-transmission method and a full fundamental parameter method are compared.     

Mikrowellenaufschluss zur Bestimmung von Spurenelementen in Pflanzenmaterial

(Microwave digestion of plant material for trace element determination.) A digestion method utilizing a mixture of nitric acid, hydrofluoric acid and hydrogen peroxide in closed vessels with a microwave system was developed for the determination of trace elements in plant materials and was tested on NIST standard reference materials [Citrus Leaves (SRM 1572) and Pine Needles (SRM 1575)] for Al, As, Ba, Cr, Cu, Fe, K, Mg, Mn, Ni, P, Pb, Rb, Sr and Zn. Analyses were done by d.c. plasma atomic emission spectrometry. The results showed high reproducibility and good agreement with the certified values. Rapid ashing and dissolution of plant material, reduced sources of contamination and the simplicity of the system make the microwave digestion system suitable for routine laboratory application.     

溶液-粉末压片法XRF分析NdFeB磁性材料的成分

结合化学酸溶方法制备样品和使用X射线荧光（XRF）光谱测量试样,建立了NdFeB合金常见主量和痕量杂质元素的快速定量分析方法。同时自制一套参考标样。方法简单。流程短,可以满足准确定量的要求。     

X射线荧光光谱铝环-双层压片法测定土壤中常量和微量元素

本文提出用铝环-双层压片法制片,经验系数法校正吸收-增强效应,对少量土壤样品中的常量和微量元素进行了定量测定。取样量为500 mg,制样与测量精确度好于5%,用本法对标样的分析表明,分析值与推荐值基本一致,本法具有简单、快速、成本低的特点,适用于少量样品的分析。     

Preliminary homogeneity study of in-house reference material using neutron activation analysis and X-ray fluorescence

Summary Although many biological reference materials for quality control of trace element analysis are commercially available, there is still a need for additional local materials for special matrices. In the Latin American region a preliminary study has been commenced involving analytical strategies for the characterization of in-house reference material. A biological sample, prepared in Brazil, constitutes the first regional attempt to prepare reference material. It was analyzed by neutron activation analysis (NAA) and X-ray fluorescence (XRF) to verify its homogeneity. The determination of the trace elements and certain major elements was carried out by instrumental NAA. Trace elements such as Cd, Mn, Mo and Cu were determined using NAA with radiochemical separations to improve the sensitivity and precision. XRF was applied only to major constituents and some trace elements with concentration of more than 10 g/g. From a total of 18 elements analyzed, only Fe, Cr and Sc were not homogeneously distributed.     

Analytical applications of delayed and instrumental neutron activation analysis

Delayed neutron activation analysis (DNAA) is a rapid and sensitive analytical method for the determination of fissile elements in a variety of samples. The present work describes two different analytical applications of delayed neutron activation for the analysis of biological and environmental samples, respectively. In the first application, DNAA was utilized to determine the natural uranium content in NIST standard reference materials (SRM) 1547 peach leaves and 1573a tomato leaves. Measured uranium mass fractions are comparable to the non-certified values listed on the certificates for these materials. In the second application, delayed neutron activation is coupled with instrumental neutron activation analysis (INAA) for the measurement of rare earth elements (REE) (cerium, lanthanum, neodymium, and ytterbium) in NIST SRM 2586, Trace Elements in Soil Containing Lead from Paint. DNAA was utilized to determine the uranium mass fraction in SRM 2586 for the subsequent application of a correction factor to account for cerium, lanthanum, and neodymium produced as part of the INAA irradiation. Measured and corrected mass fractions for the REEs described here are all within the uncertainty limits provided on the NIST certificate for SRM 2586. These results and the demonstrated sensitivity of the DNAA system establish and validate the use of this method for the determination of REEs and for potential nuclear forensics applications.     

Sensitivity of radioisotope XRF technique with particular reference to portable units

The minimum detection limit of chemical elements attainable with X-ray fluorescence analysis induced by X or γ radioactive sources are evaluated. To this purpose, after a short review of the characteristics peculiar of XRF analysis systems, the contribution of the various physical processes which determine the background for thick or thin samples, under typical operational conditions, are discussed and theoretically evaluated. Furthermore the behaviour of minimum detection limits versus the atomic number of element to be detected is theoretically evaluated for typical matrices. Such results are compared with the experimental data obtained by means of simple portable units. Useful criteria are given in order to reach the best sensitivity.     

Optimization of a glancing angle for simultaneous trace elemental analysis by using a portable total reflection X-ray fluorescence spectrometer

By using a portable total reflection X-ray fluorescence spectrometer with a 1 W X-ray tube, a specimen containing nanograms of Ca, Sc, Ti, V, Cr, Mn, Fe, and Ni is measured at several glancing angles of incident X-rays. Continuum X-rays are used as the excitation source. The intensities of the spectral background which degrades sensitivity to trace elements are decreased with a decrease of the glancing angle, and all these elements are detected at the glancing angle of 0.13° smaller than the critical angle for total reflection of the incident X-rays (0.20°). An optimum glancing angle for simultaneously detecting these trace elements is around 0.13°, and detection limits at 0.13° are sub-nanograms to ten nanograms.     

Analysis of plant hormones by microemulsion electrokinetic capillary chromatography coupled with on-line large volume sample stacking

A novel method of microemulsion electrokinetic capillary chromatography (MEEKC) coupled with on-line large volume sample stacking was developed for the analysis of six plant hormones including indole-3-acetic acid, indole-3-butyric acid, indole-3-propionic acid, 1-naphthaleneacetic acid, abscisic acid and salicylic acid. Baseline separation of six plant hormones was achieved within 10 min by using the microemulsion background electrolyte containing a 97.2% (w/w) 10 mM borate buffer at pH 9.2, 1.0% (w/w) ethyl acetate as oil droplets, 0.6% (w/w) sodium dodecyl sulphate as surfactant and 1.2% (w/w) 1-butanol as cosurfactant. In addition, an on-line concentration method based on a large volume sample stacking technique and multiple wavelength detection was adopted for improving the detection sensitivity in order to determine trace level hormones in a real sample. The optimal method provided about 50-100 fold increase in detection sensitivity compared with a single MEEKC method, and the detection limits (S/N = 3) were between 0.005 and 0.02 μg mL(-1). The proposed method was simple, rapid and sensitive and could be applied to the determination of six plant hormones in spiked water samples, tobacco leaves and 1-naphthylacetic acid in leaf fertilizer. The recoveries ranged from 76.0% to 119.1%, and good reproducibilities were obtained with relative standard deviations (RSDs) less than 6.6%.     

Determination of Sr,Zn, Cu and Fe in Licorice by X-ray Fluorescence Spectrometry

Few persons determine the trace elements in the licorice by X-ray fluorescence spectrometry (XRF), because there is no standard samples of the licorice. This paper describes the method to determine Sr,Zn,Cu and Fe in licorice using XRF. The samples are ashed and then determined with the powder process. The measured results are corrected by artificial standard samples.     

Microwave assisted digestion of atmospheric aerosol samples followed by inductively coupled plasma mass spectrometry determination of trace elements

A microwave digestion method in a closed vessel was developed for the determination of trace metals in atmospheric aerosols using inductively coupled plasma mass spectrometry (ICP-MS). A recovery study for the elements V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Cd, Sb, and Pb was conducted using multi-elemental standard solutions, NIST 1633b Trace Elements in Coal Fly Ash, and NIST 1648 Urban Particulate Matter. A simple digestion method using only HNO3/H2O2 gave good recoveries (90%-108%) for all elements except Cr in SRM 1648, but yielded low recoveries for SRM 1633b. A more robust method using HNO3/H2O2/HF/H3BO3 yielded higher recoveries (82%-103%) for the lighter elements (V-Zn) in SRM 1633b, and improved the Cr recovery in SRM 1648, but decreased the Se recovery in both SRMs. A comparative analysis of aerosol samples obtained at a remote mountain location Nathiagali, Pakistan (2.5 km above mean sea level), and Mayville, New York, downwind from the highly industrialized Midwestern United States, was carried out using Instrumental Neutron Activation Analysis (INAA) for the elements Cr, Mn, Fe, Co, Zn, As, Se, and Sb. The simple digestion method yielded excellent agreement for Cr, Fe, Zn, As, Se, and Sb, with slopes of the ICP-MS vs. INAA regressions of 0.90-1.00 and R2 values of 0.96-1.00. The regressions for Mn and Co had slopes of 0.82 and 0.84 with R2 values of 0.83 and 0.82, respectively. Addition of HF/H3BO3 did not improve the correlation for any of the elements and degraded the precision somewhat. The technique provides sensitivity and accuracy for trace elements in relatively small aerosol samples used in atmospheric chemistry studies related to SO2 oxidation in cloud droplets. The ability to determine concentrations of a very large number of elements from a single analysis will permit source apportionment of various trace pollutants and hence strategies to control the sources of air pollution. This is particularly important as the health effects of particulate matter are increasingly recognized.     

萤石成分分析方法的标准现状与研究进展

萤石是一种重要的战略性非金属矿产资源,本文对中国国家标准、行业标准、国际标准（ISO）、美国标准（ASTM）以及俄罗斯标准（GOST）中的萤石成分分析标准方法的现状进行了介绍。对近年来X射线荧光光谱法（XRF）、电感耦合等离子体发射光谱法（ICP-AES）、电感耦合等离子体质谱法（ICP-MS）、激光诱导击穿光谱法（LIBS）等技术在萤石成分分析中的应用以及标准物质/标准样品研制情况进行了总结和评述。文章认为,萤石分析测试技术标准体系相对完备,XRF、ICP-AES、ICP-MS等仪器分析测试技术已普遍应用于萤石样品实验室分析,建议尽快研究并建立萤石中稀土等微量元素测定的标准方法,并开展相应标准物质/标准样品的研制,同时应大力开展原位在线分析技术的研究与开发,以适应工业在线自动化监测的需求,LIBS与在线XRF技术联合在萤石在线分析方面具有良好的应用潜力。     

Application of vapor phase decomposition/total reflection X-ray fluorescence in the silicon semiconductor manufacturing environment

Total reflection X-ray fluorescence (TXRF), in combination with vapor phase decomposition (VPD), provides an efficient method for analyzing trace metal contaminants on silicon wafer surfaces. The progress made in applying these techniques to the analysis of silicon wafers in a wafer fabrication cleanroom environment is reported. Methods of standardization are presented, including the preparation and characterization of VPD standards. While the VPD wafer preparation process increases the sensitivity of the TXRF measurement by at least one order of magnitude, inherent uncertainties associated with the VPD technique itself are apparent. Correlation studies between VPD/TXRF and VPD/inductively coupled plasma mass spectrometry (ICP-MS) are presented.     

Analytical possibilities of different X-ray fluorescence systems for determination of trace elements in aqueous samples pre-concentrated with carbon nanotubes

This study was aimed to achieve improved instrumental sensitivity and detection limits for multielement determination of V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Se, Pb and Cd in liquid samples by using different X-ray fluorescence (XRF) configurations (a benchtop energy-dispersive X-ray fluorescence spectrometer, a benchtop polarised energy-dispersive X-ray fluorescence spectrometer and a wavelength-dispersive X-ray fluorescence spectrometer).The preconcentration of metals from liquid solutions consisted on a solid-phase extraction using carbon nanotubes (CNTs) as solid sorbents. After the extraction step, the aqueous sample was filtered and CNTs with the absorbed elements were collected onto a filter paper which was directly analyzed by XRF.The calculated detection limits in all cases were in the low ng mL^− 1 range. Nevertheless, results obtained indicate the benefits, in terms of sensitivity, of using polarized X-ray sources using different secondary targets in comparison to conventional XRF systems, above all if Cd determination is required.The developed methodologies, using the aforementioned equipments, have been applied for multielement determination in water samples from an industrial area of Poland.     

Results of the ASTM Nuclear Methods intercomparison on NIST apple and peack leaves standard reference materials

The ASTM Task Group on Nuclear Methods of Chemical Analysis (E10.05.12) has conducted a trace element intercomparison among some of its members over the past two years. Eight non-NIST laboratories submitted data using nuclear techniques, with a total of 111 values for the apple leaves and 116 values for the peach leaves, on 46 and 50 elements, respectively. This intercomparison provided a unique opportunity for the analytical laboratories, because the analytical values submitted could be later compared to the NIST certified values. For the seven elements which were certified by NIST and had three or more intercomparison values, the results showed that: 1) 61% of all 56 intercomparison values submitted had results whose stated uncertainty overlapped the uncertainty limits of the NIST certified values, and 2) less than 6% of the intercomparison values had means which fell outside ±20% of the NIST values. In general, the intercomparison values submitted showed excellent agreement with the NIST values. However, many reported uncertainties accompanying intercomparison values appeared overly optimistic.