All-solid-state electronic tongue and its application for beverage analysis

Disposable all-solid-state planar-type potentiometric electronic tongue has been developed with the carbon paste electrode array screen-printed on a polymeric substrate. Highly cross-sensitive solvent polymeric membranes based on different matrices [e.g. poly(vinyl chloride) (PVC), aromatic polyurethane, and polypyrrole (Ppy)] and doped with common electroactive components for potentiometric measurements (e.g. various plasticizers, and cation- and anion-selective ionophores) were deposited on the screen-printed carbon paste electrodes (SCPEs). It was observed that an incorporation of 10 wt.% of Prussian Blue (PB; Fe₄(III)[Fe(II)(CN)₆]₃) into a commercially available carbon paste and electrochemical preanodization of SCPEs in KCl solution at 1.6 V provide the all-solid-state planar-type electrodes with significantly improved potentiometric stability. The proposed fabrication method gives possibility for simple and reproducible mass-production of low-cost disposable electronic tongue microsystems. The practical utility of all-solid-state disposable electronic tongue chips has been demonstrated with a flow injection cell for the analysis of potable waters, soft drinks, and beers. It is shown that the potentiometric measurements with the SCPE-based all-solid-state chips and the combined use of chemometric methods (e.g. principal components analysis, partial least regression (PLS), and principal component regression (PCR)) for the analysis of obtained data sets successfully discriminate various types of samples according to their tastes.     

Development of an electronic tongue based on a PEDOT-modified voltammetric sensor

Three different electrodes were tested for use as nonspecific amperometric sensors for blind analysis on real matrices, namely different fruit juices from different fruits or different brands. The first two electrodes were traditional Pt and Au electrodes, while the third one was modified with poly(3,4-ethylenedioxythiophene) conducting polymer. The sensors were tested separately, tested coupled to each other, and also tested together. The responses of the electrode system(s) were first screened via PCA and then their discriminant capabilities were quantified in terms of the sensitivities and specificities of their corresponding PLS-DA multivariate classification models. Particular attention was paid to analyzing the evolution of the response over subsequent potential sweeps. The modified electrode demonstrated the most discriminating ability, and it was the only system capable of satisfactorily performing the most complex task attempted during the analysis: discriminating between juices from the same fruit but from different brands. Moreover, the electrode "cleaning" procedure required between two subsequent potential sweeps was much simpler for the modified electrode than for the others. This electrode system was therefore shown to be a good candidate for use as an informative element in an electronic tongue applied to the analysis of other food matrices.     

The effects of carbon nanotubes on the electrocatalysis of hydrogen peroxide by metallo-phthalocyanines

The pre-grafted screen-printed gold electrode modified with phenyl-amino monolayer was investigated for covalent immobilization of phenyl-amine functionalized single-walled carbon nanotubes (PA-SWCNT) and metal tetra-amino phthalocyanine (MTAPc) using Schiff-base reactions with benzene-1,4-dicarbaldehyde (BDCA) as cross-linker. The PA-SWCNT and MTAPc modified electrodes were applied as hybrids for electrochemical sensing of H₂O₂. The step-by-step fabrication of the electrode was followed using electrochemistry, impedance spectroscopy, scanning electron microscopy and Raman spectroscopy and all these techniques confirmed the fabrication and the immobilization of PA-SWCNT, MnTAPc and CoTAPc onto gold surfaces. The apparent electron transfer constant (k_app) showed that the carbon nanotubes and metallo-phthalocyanines hybrids possess good electron transfer properties compared to the bare, pre-grafted and the MTAPc modified gold electrode surfaces without PA-SWCNT. The electrochemical sensing of hydrogen peroxide was successful with PA-SWCNT-MTAPc hybrid systems showing higher electrocatalytic currents compared to the other electrodes. The analytical parameters obtained using chronoamperometry gave good linearity at H₂O₂ concentrations ranging from 1.0 to 30.0 μmol L⁻¹. The values for the limit of detection (LoD) were found to be of the orders of 10⁻⁷ M using the 3δ for all the electrodes. The PA-SWCNT-MTAPc modified SPAuEs were much more sensitive compared to PA-MTAPc modified SPAuEs.     

Use of nickel implanted boron-doped diamond thin film electrode coupled to HPLC system for the determination of tetracyclines

The electrochemical analysis of tetracyclines was investigated using nickel-implanted boron-doped diamond thin film electrode (Ni-DIA) by cyclic voltammetry and high performance liquid chromatographic with amperometry. Cyclic voltammetry was used to study the electrochemical oxidation of tetracyclines. Comparison experiments were carried out utilizing as-deposited BDD and glassy carbon electrodes. Ni-DIA electrode provided well-resolved oxidative irreversible cyclic voltammograms and the highest current signals among the electrode studied. High performance liquid chromatography (HPLC) with amperometric detection was also studied. The chromatography was performed using a commercially available Inertsil C18 column, with the mobile phase being: 80% phosphate buffer (pH 2.5)-20% acetonitrile and detected at 1.55 V. The methods were validated over the concentration range 0.05-100 ppm with the overall average recoveries from 83.3 to 102.5% and R.S.D. of less than 10%. The proposed method was further applied to analyse shrimp samples.     

Direct amperometric determination of tert-butylhydroquinone in biodiesel

The direct amperometric determination of tert-butylhydroquinone (TBHQ) in biodiesel at an unmodified glassy carbon electrode is reported. A biodiesel aliquot was added into an electrochemical cell containing a 75% (v/v) ethanol-water solution under stirring (with final concentration of 50 mmol L⁻¹ HClO₄). The amperometric method involved the continuous application of three sequential potential pulses to the working electrode (700 mV for 300 ms, 0 mV for 100 ms and −50 mV for 1 s). TBHQ was continuously monitored at the first (direct oxidation) and optionally at the second (reduction) potential pulse while the third potential pulse was applied for cleaning of the electrode surface. For comparison, the samples were also analyzed by high-performance liquid-chromatography and a good agreement between the results was verified. Recovery values for spiked samples were between 90% and 95% and the reproducibility of the proposed method was around 5% (n = 5). The proposed method can be easily adapted for on-site analysis.     

Development and characterization of a new conducting carbon composite electrode

A new conducting composite flexible material prepared from cellulose acetate (CA) polymer and graphite has been developed and used for the fabrication of electrodes, which were then characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Scanning electron microscopy (SEM) was used to provide information concerning the morphology of the composite electrode surface. The potential window, background currents and capacitance were evaluated by cyclic voltammetry in the pH range from 4.6 to 8.2. The voltammetry of model electroactive species demonstrates a close to reversible electrochemical behaviour, under linear diffusion control. The electroactive area of the composite electrodes increases after appropriate electrode polishing and electrochemical pre-treatment. The electrodes were used as substrate for the electropolymerisation of the phenazine dye neutral red, for future use as redox mediator in electrochemical biosensors. The composite electrodes were also successfully used for the amperometric detection of ascorbate at 0.0 V vs. SCE, and applied to the measurement of ascorbate in Vitamin C tablets; the sensor exhibits high sensitivity and a low detection limit of 7.7 μM. Perspectives for use as a versatile, mechanically flexible and robust composite electrode of easily adaptable dimensions are indicated.     

Square Wave Stripping Voltammetry of Unlabeled Single‐ and Double‐Stranded DNAs

We show that, in difference to previously applied electrochemical methods working with stationary electrodes, square wave voltammetry produces well‐developed peaks II_SW (specific for dsDNA) and III_SW yielded by ssDNA at hanging mercury drop electrode (HMDE) and solid amalgam electrodes (SAEs). Using these peaks various kinds of DNA structural transitions can be studied, including unwinding of dsDNA at negatively charged electrode surfaces. The sensitivity of the DNA analysis is much better than that obtained with guanine oxidation signals at carbon electrodes. Both carbon electrodes and SAEs appear attractive as transducers in label‐free RNA and DNA sensors.     

Simultaneous determination of antioxidants at a chemically modified electrode with vitamin B12 by capillary zone electrophoresis coupled with amperometric detection

In the paper, a new kind of vitamin B₁₂ (acquo-cobalamine) chemically modified electrode was fabricated and applied in capillary zone electrophoresis coupled with amperometric detection (CZE-AD) for simultaneous determination of six antioxidants in fruits and vegetables. The catalytic electrochemical properties of the chemically modified electrode could obviously enhance oxidation peak heights responses by about five times to glutathione, ascorbic acid, vanillic acid, chlorogenic acid, salicylic acid, and caffeic acid compared with common carbon disk electrode. Furthermore, the effects of working electrode potential, pH and concentration of running buffer, separation voltage and injection time on CZE-AD were investigated. Under the optimum conditions, the six analytes could be completely separated and detected in a borate-phosphate buffer (pH 8.4) within 15 min. Their linear ranges were from 2.5 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ and the detection limits were as low as 10⁻⁸ mol L⁻¹ magnitude (S/N = 3). The proposed method has been successfully employed to monitor the six analytes in practical samples with recoveries in the range 96.0-106.0% and RSDs less than 5.0%. Above results demonstrate that capillary zone electrophoresis coupled with electrochemical detection using vitamin B₁₂ modified electrode as detector is of convenient preparation, high sensitivity, good repeatability, and could be used in the rapid determination of practical samples.     

Cyclic voltammetry and impedance spectroscopy analysis for graphene-modified solid-state electrode transducers

The transducer of solid-state electrodes based on an epoxy-graphite composite was modified by two different methods, such as direct mixed and layer deposition of graphene (commercial and synthesized by electrochemical exfoliation of graphite). The modified electrodes were characterized by cyclic voltammetry and impedance spectroscopy. Also, scanning electron microscopy (SEM) was carried out to acquire information concerning the morphology of the composite electrode. Voltammetric measurements, in presence of [Fe(CN)₆]^3? as electroactive standard, determined a quasi-reversible electrochemical behavior under linear diffusion control. Electronic transference for modified and unmodified electrodes was compared. Solid-state electrode modified by inclusion of synthesized graphene showed a better electronic transference at electrode surface, due to the lower potential difference between anodic and cathodic peaks (ΔE = 125 mV) with respect to unmodified electrode (ΔE = 160 mV). Impedance spectroscopy characterization of electrode bodies in solid-state it was revealed a higher electronic conductivity and a supercapacitive behavior for the modified composites (values of intrinsic capacitances in the order of nanofarads) due to inclusions of graphite and graphene in the epoxy matrix. These inclusions were verified through SEM microscopy. The electronic conductivity and the supercapacitive character contributed both to the enhancement of electronic transference at electrode surface.     

Myoglobin/arylhydroxylamine film modified electrode: Direct electrochemistry and electrochemical catalysis

The adsorption processes and electrochemical behavior of 4-nitroaniline (4-NA) adsorbed onto glassy carbon electrodes (GCE) have been investigated in aqueous 0.1 M nitric acid (HNO₃) electrolyte solutions using cyclic voltammetry (CV). 4-NA adsorbs onto GCE surfaces, and upon potential cycling past −0.2 V, is transformed into the arylhydroxylamine (ArHA) derivative which exhibits a well-behaved pH dependent redox couple centered at 0.32 V at pH 1.5. It is noted as arylhydroxylamine modified glassy carbon electrodes (HAGCE). This modified electrode can be readily used as an immobilization matrix to entrap proteins and enzymes. In our studies, myoglobin (Mb) was used as a model protein for investigation. A pair of well-defined reversible redox peaks of Mb (Fe(III)-Fe(II)) was obtained at the Mb/arylhydroxylamine modified glassy carbon electrode (Mb/HAGC) by direct electron transfer between the protein and the GCE. The formal potential (E^0′), the apparent coverage (Γ^*) and the electron-transfer rate constant (k_s) were calculated as −0.317 V, 8.26 × 10⁻¹² mol/cm² and 51 ± 5 s⁻¹, respectively. Dramatically enhanced biocatalytic activity was exemplified at the Mb/HAGC electrode by the reduction of hydrogen peroxide (H₂O₂), trichloroacetic acid (TCA) and oxygen (O₂). The Mb/arylhydroxylamine film was also characterized by UV-visible spectroscopy (UV-vis), scanning electron microscope (SEM) indicating excellent stability and good biocompatibility of the protein in the arylhydroxylamine modified electrode. This new Mb/HAGC electrode exhibited rapid electrochemical response (2 s) for H₂O₂ and had good stability in physiological condition, showing the potential applicability of the films in the preparation of third generation biosensors or bioreactors based on direct electrochemistry of the proteins.     

Periodically interrupted amperometry at membrane coated electrodes: a simplified pulsed amperometry

Amperometric detection combined with separation technique or with selective molecular recognition step can be very effective solving quantitative analytical tasks. When the amperometric working electrode surface needs cleaning or reactivation, pulsed amperometric technique can be the choice. Coating working electrodes with different sensitizing or protecting layer is quite common in the practice of voltammetric analysis. In these studies the behavior of coated electrodes using a simplified pulsed amperometric working program which can be named periodically interrupted amperometric (PIA) detection has been investigated. Rotating platinum, and carbon paste electrodes coated with dialysis film or porcine intestinal membrane were used in the experiments. The signal in case of electrochemical oxidation of hydrogen peroxide and ascorbic acid at convective conditions has been evaluated. The signal, obtained with conventional amperometry has been compared with signal collected with a periodically interrupted amperometric measuring program, allowing time for the diffusion to reload the diffusion layer at the electrode surface. The sensitivity and the lower limit of detection (4.5 × 10⁻⁷ M for ascorbic acid and 2 × 10⁻⁶ M for H₂O₂) proved superior in case of the periodically interrupted amperometry.     

Polycrystalline Gold Electrodes: A Comparative Study of Pretreatment Procedures Used for Cleaning and Thiol Self‐Assembly Monolayer Formation

The influence of different surface pretreatment procedures on the electrochemical response of a polycrystalline gold electrode was evaluated. Mechanical polishing with slurry alumina (M), chemical oxidation with H₂SO₄/H₂O₂ (C), electrochemical polishing (potential cycling between ?0.1 V and 1.2 V vs. SCE) (E), chemical reduction with ethanol, and combinations among these treatments were employed to change the surface electrode characteristics. The efficiency of the proposed pretreatments was evaluated by electrochemical responses towards the redox couple ferri(II/III)‐ammonium sulfate and by the formation of a self‐assembly monolayer of 3‐mercaptopropionic acid (3 MPA SAM) on gold electrodes. The procedure (C) allowed important gold surfaces activation. Using procedures (C) and (E) the roughness of polycrystalline gold surfaces was significantly minimized and more reproducible surfaces could be obtained. From the profile of reductive desorption of 3 MPA SAM it was possible to verify that reduced gold surfaces generated better packed monolayers than oxidized ones and a comparative study using CV and DPV techniques showed that between the two desorption peaks, the one localized at more negative potential values corresponds to the cleavage of Au‐S bond from the chemisorbed thiol. In general, the improvement in the studied electrochemical responses could not only be attributed to an increase in the real surface area of the electrode, but to the chemical surface states set off by the pretreatment procedure.     

Sarcosine oxidase composite screen-printed electrode for sarcosine determination in biological samples

As the prostate cancer (PCa) progresses, sarcosine levels increase both in tumor cells and urine samples, suggesting that this metabolite measurements can help in the creation of non-invasive diagnostic methods for this disease. In this work, a biosensor device was developed for the quantification of sarcosine via electrochemical detection of H₂O₂ (at 0.6 V) generated from the catalyzed oxidation of sarcosine. The detection was carried out after the modification of carbon screen printed electrodes (SPEs) by immobilization of sarcosine oxidase (SOX) on the electrode surface. The strategies used herein included the activation of the carbon films by an electrochemical step and the formation of an NHS/EDAC layer to bond the enzyme to the electrode, the use of metallic or semiconductor nanoparticles layer previously or during the enzyme immobilization. In order to improve the sensor stability and selectivity a polymeric layer with extra enzyme content was further added. The proposed methodology for the detection of sarcosine allowed obtaining a limit of detection (LOD) of 16 nM, using a linear concentration range between 10 and 100 nM. The biosensor was successfully applied to the analysis of sarcosine in urine samples.     

Ammonium and Phosphate Quantification in Wastewater by Using a Voltammetric Electronic Tongue

Ammonia (NH₄? N) and orthophosphate (PO₄? P) quantification in wastewater treatment plants is important due to their implication in the eutrophication process. A voltammetric electronic tongue as a tool for the prediction of ammonia and orthophosphate concentrations from influent and effluent wastewater is proposed herein. An electrochemical study of the response of the ammonium and orthophosphate ions was performed in order to design a suitable waveform for each electrode. Partial Least Squares analysis was used to obtain a correlation between the data from the tongue and the concentrations of ammonia and orthophosphate measured in the laboratory showing good predictive power.     

Additional Studies on the Electrochemical Behaviour of Three Macrolides on Pt and Carbon Based Electrodes

The voltammetric behaviour of the macrolide based antibiotic: Erythromycin (ERT), Clarithromycin (CLA) and Azithromycin (AZT) was presented in this work. Carbon electrodes and platinum (Pt) electrode were applied as working electrodes. Cyclic voltamograms of each molecule in each electrode were recorded and similar electrochemical behaviour of macrolides was observed for all carbon based electrodes, which gave more defined current intensity peaks than platinum. Other organic compounds were tested trying to clarify electro-active groups of macrolides. Experiments on mechanism of electrochemical reaction were performed, and studies on the influence of pH on peak current and peak potential were also carried out.     

Amorphous carbon nitride as an alternative electrode material in electroanalysis: Simultaneous determination of dopamine and ascorbic acid

Boron-doped diamond (BDD) films are excellent electrode materials, whose electrochemical activity for some analytes can be tuned by controlling their surface termination, most commonly either to predominantly hydrogen or oxygen. This tuning can be accomplished by e.g. suitable cathodic or anodic electrochemical pretreatments. Recently, it has been shown that amorphous carbon nitride (a-CN_x) films may present electrochemical characteristics similar to those of BDD, including the influence of surface termination on their electrochemical activity toward some analytes. In this work, we report for the first time a complete electroanalytical method using an a-CN_x electrode. Thus, an a-CN_x film deposited on a stainless steel foil by DC magnetron sputtering is proposed as an alternative electrode for the simultaneous determination of dopamine (DA) and ascorbic acid (AA) in synthetic biological samples by square-wave voltammetry. The obtained results are compared with those attained using a BDD electrode. For both electrodes, a same anodic pretreatment in 0.1 mol L⁻¹ KOH was necessary to attain an adequate and equivalent separation of the DA and AA oxidation potential peaks of about 330 mV. The detection limits obtained for the simultaneous determination of these analytes using the a-CN_x electrode were 0.0656 μmol L⁻¹ for DA and 1.05 μmol L⁻¹ for AA, whereas with the BDD electrode these values were 0.283 μmol L⁻¹ and 0.968 μmol L⁻¹, respectively. Furthermore, the results obtained in the analysis of the analytes in synthetic biological samples were satisfactory, attesting the potential application of the a-CN_x electrode in electroanalysis.     

Prussian blue modified glassy carbon electrodes-study on operational stability and its application as a sucrose biosensor

Stabilisation of electrochemically deposited Prussian blue (PB) films on glassy carbon (GC) electrodes has been investigated and an enhancement in the stability of the PB films is reported if the electrodes are treated with tetrabutylammonium toluene-4-sulfonate (TTS) in the electrochemical activation step following the electrodeposition. A multi-enzyme PB based biosensor for sucrose detection was made in order to demonstrate that PB films can be coupled with an oxidase system. A tri-enzyme system, comprising glucose oxidase, mutarotase and invertase, was crosslinked with glutaraldehyde and bovine albumin serum on the PB modified glassy carbon electrode. The deposited PB operated as an electrocatalyst for electrochemical reduction of hydrogen peroxide, the final product of the enzyme reaction sequence. The electrochemical response was studied using flow injection analysis for the determination of sucrose, glucose and H₂O₂. The optimal concentrations of the immobilisation mixture was standardised as 8 U of glucose oxidase, 8 U of mutarotase, 16 U of invertase, 0.5% glutaraldehyde (0.025 μl) and 0.5% BSA (0.025 mg) in a final volume of 5 μl applied at the electrode surface (0.066 cm²). The biosensor exhibited a linear response for sucrose (4-800 μM), glucose (2-800 μM) and H₂O₂ (1-800 μM) and the detection limit was 4.5, 1.5 and 0.5 μM for sucrose, glucose and H₂O₂, respectively. The sample throughput was ca. 60 samples h⁻¹. An increase in the operational and storage stability of the sucrose biosensor was also noted when the PB modified electrodes were conditioned in phosphate buffer containing 0.05 M TTS during the preparation of the PB films.     

Molecular-level functionalization of electrode surfaces. An overview

Electrochemical reactions occur at electrode/electrolyte interfaces. Hence, manipulation and design of electrochemical interfaces accompanied by surface modifications have assumed vital importance. Molecular level modification, either at the monolayer or multilayer level of electrode surfaces and leading to functionalization of electrodes, is being actively pursued by researchers. Modification based on the self-assembled monolayer approach has enabled electrodes to acquire molecular recognition and molecular electronic characteristics. Functionalization of electrode surfaces using polymeric materials and enzymes has facilitated electrodes in exhibiting properties like catalysis, molecular recognition, electrochromism and birefringence. The results of such molecular level functionalization studies of electrode surfaces carried out recently in our laboratories are presented in this overview. Besides, some representative results reported from elsewhere are also included.     

Bismuth Film Electrode as an Alternative for Mercury Electrodes: Determination of Azo Dyes and Application for Detection in Food Stuffs

Bismuth electrodes were investigated and exhibit electrochemical properties similar to mercury electrodes but with much lower toxicity. An electrochemical application of bismuth film modified glassy carbon electrode for azo dyes determination was investigated. The plating step was optimized in order to achieve its analytical efficiency. A plating potential of ?0.9 V in a solution of 200 mg/L Bi(NO₃)₃, 0.5 M HNO₃ for 100 s yields to a suitable electrode (in terms of stability and detection). Azo dyes such as azorubine (i.e., carmoisine, E122), amaranth (E123), ponceau 4R (i.e., new coccine, E124) and allura red (E129) were determined by differential pulse voltammetry in a NaCl solution in the concentration range of few ppm to 100 ppm. The reproducibility of the signal, characterized by the relative standard deviation, was found to be less than 5%, the detection and quantification limits were few mg/L. The influence of other food components on the signal was studied and the applicability was tested on real beverages samples.     

An influence of pretreatment conditions on surface structure and reactivity of Pt(100) towards CO oxidation reaction

We present a combined electrochemical and in situ STM study of the surface structure of Pt(100) single crystal electrodes in dependence on the cooling atmosphere after flame annealing. The following cooling conditions were applied: Ar/H₂ and Ar/CO mixtures (reductive atmosphere), argon (inert gas) and air (oxidative atmosphere). Surface characterization by in-situ STM allows deriving direct correlations between surface structure and macroscopic electrochemical behavior of the respective platinum electrodes. We investigated the influence of defect type and density as well as long range surface order on the kinetics of the CO electro-oxidation reaction. The defect-rich Pt(100) electrodes as cooled in air or Ar, and followed by immersion in the hydrogen adsorption region display higher activities as compared to the rather smooth Pt(100)-(1 × 1) electrode cooled in an Ar/H₂-atmosphere.