Presence of phthalates in contact lens and cleaning solutions

A fast and simple method using liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been applied to identify and quantify four phthalic acid esters (PAEs) in different contact lens cleaning solutions. A migration study of these compounds from contact lenses has also been performed. The PAEs studied were dimethyl phthalate, diethyl phthalate, butyl benzyl phthalate and dibutyl phthalate. The migration of PAEs from contact lenses was performed by suspending each contact lens in an artificial tear solution at 37 °C and shaking it at 130 rpm for 24 h. The purpose of this study was to determine a possible migration of these compounds to the eyes as a result of the use of contact lenses and their cleaning solutions. The method was precise (with relative standard deviation (RSD) from 2.2 to 11.9%). It was also sensitive, with LODs of 0.03, 0.19, 0.31 and 2.62 μg L^− 1 for DMP, DEP, BBP and DBP respectively. The results obtained confirm the presence of these substances in some types of contact lens cleaning solutions. Furthermore, DBP and BBP were liberated from the contact lenses during the migration study.     

Simultaneous screening and determination eight phthalates in plastic products for food use by sonication-assisted extraction/GC-MS methods

Studies on determination of eight kinds of phthalates, e.g. di-ethyl phthalate (DEP), di-propyl phthalate (DPP), di-isobutyl phthalate (DIBP), di-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-cyclohexyl phthalate (DCHP), di-(2-ethylhexyl) phthalate (DEHP), di-octyl phthalate (DOP), in 25 kinds of plastic products for food use, including packaging bags, packaging film, containers, boxes for microwave oven use, sucking tubes, spoons, cups, plates, etc. by gas chromatography in combination with mass spectrometry detector (GC-MS) in electronic ionisation mode (EI) with selected-ion monitoring (SIM) acquisition method (GC-MS (EI-SIM)) have been carried out. Methods have been developed for both qualitative and quantitative analysis of phthalates. Extraction, clean-up and analysis procedure have been optimized. Determination of samples were performed after frozen in liquid nitrogen and sonication-assisted extraction with hexane, clean-up with LC-C18 SPE and analyzed by GC-MS methods. The base peak (m/z = 149) of all the phthalates was selected for the screening studies. The characteristic ions, 121, 177, 222 for DEP; 191, 209 for DPP; 57, 223 for DIBP; 104 for DBP; 91, 132, 206 for BBP; 55, 167 for DCHP; 113, 167, 279 for DEHP; 279 for DOP were chosen for quantitative studies. These techniques are possible to detect phthalates at the level of 10.0 μg/kg. Overall recoveries were 82-106% with R.S.D. values at 3.8-10.2%. Only one of the 25 examined samples was free from phthalates. The rest 24 samples were found to contain at least three or more of these phthalates. The predominant phthalate detected in the studied samples was DEHP.     

Evaluation of the Removal of Selected Phthalic Acid Esters (PAEs) in Municipal Wastewater Treatment Plants Supported by Constructed Wetlands

Phthalic acid esters (PAEs) have a negative impact on living organisms in the environment, therefore, are among the group of Endocrine Disrupting Compounds (ECDs). Unfortunately, conventional methods used in municipal wastewater treatment plants (MWWTPs) are not designed to eliminate PAEs. For this reason, the development of cheap and simple but very effective techniques for the removal of such residues from wastewater is crucial. The main aim of this study was the evaluation of the removal of six selected PAEs: diethyl phthalate (DEP), di-n-octyl phthalate (DOP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), bis(2-ethylhexyl) phthalate (DEHP) and dimethyl phthalate (DMP), in real MWWTPs supported by constructed wetlands (MWWTP–CW system). For the first time, the possibility of using three new plants for this purpose, Cyperus papyrus (papyrus), Lysimachia nemorum (yellow pimpernel) and Euonymus europaeus (European spindle), has been presented. For determining the target PAEs in wastewater samples, a method of SPE (Solid-Phase Extraction)–GC–MS(SIM) was developed and validated, and for plant materials, a method of UAE (Ultrasound-Assisted Extraction)–SPE–GC–MS(SIM) was proposed. The obtained data showed that the application of the MWWTP–CW system allows a significant increase in the removal of DEP, DBP, BBP and DEHP from the wastewater stream. Euonymus europaeus was the most effective among the tested plant species for the uptake of analytes (8938 ng × g⁻¹ dry weight), thus, this plant was found to be optimal for supporting conventional MWWTPs.     

Simultaneous distillation-extraction of high-value volatile compounds from Cistus ladanifer L

The present paper describes a procedure to isolate volatiles from rock-rose (Cistus ladanifer L.) using simultaneous distillation-extraction (SDE). High-value volatile compounds (HVVC) were selected and the influence of the extraction conditions investigated. The effect of the solvent nature and extraction time on SDE efficiency was studied. The best performance was achieved with pentane in 1 h operation. The extraction efficiencies ranged from 65% to 85% and the repeatability varied between 4% and 6% (as a CV%).The C. ladanifer SDE extracts were analysed by headspace solid phase microextraction (HS-SPME) followed by gas chromatography with flame ionization detection (GC-FID). The HS-SPME sampling conditions such as fiber coating, temperature, ionic strength and exposure time were optimized. The best results were achieved with an 85 μm polyacrylate fiber for a 60 min headspace extraction at 40 °C with 20% (w/v) of NaCl. For optimized conditions the recovery was in average higher than 90% for all compounds and the intermediate precision ranged from 4 to 9% (as CV %). The volatiles α-pinene (22.2 mg g⁻¹ of extract), 2,2,6-trimethylcyclohexanone (6.1 mg g⁻¹ of extract), borneol (3.0 mg g⁻¹ of extract) and bornyl acetate (3.9 mg g⁻¹ of extract) were identified in the SDE extracts obtained from the fresh plant material.     

Synthesis, FTIR, solid-state NMR and SEM studies of novel polyampholytes or polyelectrolytes obtained from EGDE, MAA and imidazoles

Novel materials with either polyampholyte or polyelectrolyte character and coordination properties were obtained by reaction of methacrylic acid (MAA), imidazole (IM) or 2-methylimidazole (2MI) and ethylene glycol diglycidyl ether (EGDE) in the presence of benzoyl peroxide.This new synthetic strategy gave rise to non-soluble, compact plastics that can be milled into non-porous particles.The polymers were studied by solid-state ¹³C NMR spectroscopy, FT IR and scanning electron microscopy (SEM).The experimental values of the isoelectric point (pI) were 6.04 ± 0.02 for poly(EGDE-MAA-IM) and 6.4 ± 0.2 for poly(EGDE-MAA-2MI). The water content was low due to the high cross-linking degree.These materials behaved as ionic exchangers. Copper (Cu²⁺) was chosen as a model, the equilibrium binding was analyzed, and the coordination properties were studied by FTIR and scanning electron microscopy/energy dispersive X-ray analysis (SEM/EDS).The maximum binding capacity for copper ion was 67 mg g⁻¹ for poly(EGDE-MAA-IM), 57 mg g⁻¹ for poly(EGDE-MAA-2MI) and 0.9 mg g⁻¹ for poly(EGDE-MAA).     

Assessment of cadmium and iron adsorption in sediment,employing a flow injection analysis system with on line filtration and detection by flame atomic absorption spectrometry and thermospray flame furnace atomic absorption spectrometry

This work presents an evaluation of iron and cadmium adsorption in sediment of the Furnas Hydroelectric Plant Reservatory located in Alfenas, Minas Gerais (Brazil). The metal determination was done employing a flow injection analysis (FIA) with an on-line filtering system. As detection techniques, flame atomic absorption spectrometry (FAAS) for iron and thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) for cadmium determinations were used. The developed methodology presented good limits of detection, being 190 μg L⁻¹ for iron and 1.36 μg L⁻¹ for cadmium, and high sampling frequency for both metals 144 and 60 readings h⁻¹ for iron and cadmium, respectively. Both metals obey the Langmuir model, with maximum adsorptive capacity of 0⋅169 mg g⁻¹ for iron and 7⋅991 mg g⁻¹ for cadmium. For iron, a pseudo-first-order kinetic model was obtained with a theoretical Q_e = 9⋅8355 mg g⁻¹ (experimental Q_e = 9⋅5432 mg  g⁻¹), while for cadmium, a pseudo-second-order kinetic model was obtained, with a theoretical Q_e = 0.3123 mg g⁻¹ (experimental Q_e = 0⋅3052 mg g⁻¹).     

Sorptive potential of sunflower stem for Cr(III) ions from aqueous solutions and its kinetic and thermodynamic profile

The sorptive potential of sunflower stem (180-300 μm) for Cr(III) ions has been investigated in detail. The maximum sorption (≥85%) of Cr(III) ions (70.2 μM) has been accomplished using 30 mg of high density sunflower stem in 10 min from 0.001 M nitric and 0.0001 M hydrochloric acid solutions. The accumulation of Cr(III) ions on the sorbent follows Dubinin-Radushkevich (D-R), Freundlich and Langmuir isotherms. The isotherm yields D-R saturation capacity X_m = 1.60 ± 0.23 mmol g⁻¹, β = −0.00654 ± 0.00017 kJ² mol⁻², mean free energy E = 8.74 ± 0.12 kJ mol⁻¹, Freundlich sorption capacity K_F = 0.24 ± 0.11 mol g⁻¹, 1/n = 0.90 ± 0.04 and of Langmuir constant K_L = 6800 ± 600 dm³ mol⁻¹ and C_m = 120 ± 18 μmol g⁻¹. The variation of sorption with temperature (283-323 K) gives ΔH = −23.3 ± 0.8 kJ mol⁻¹, ΔS = −64.0 ± 2.7 J mol⁻¹ K⁻¹ and ΔG_298k = −4.04 ± 0.09 kJ mol⁻¹. The negative enthalpy and free energy envisage exothermic and spontaneous nature of sorption, respectively. Bisulphate, Fe(III), molybdate, citrate, Fe(II), Y(III) suppress the sorption significantly. The selectivity studies indicate that Cr(III), Eu(III) and Tb(III) ions can be separated from Tc(VII) and I(I). Sunflower stem can be used for the preconcentration and removal of Cr(III) ions from aqueous medium. This cheaper and novel sorbent has potential applications in analytical and environmental chemistry, in water decontamination, industrial waste treatment and in pollution abatement. A possible mechanism of biosorption of Cr(III) ions onto the sunflower stem has been proposed.     

Mineral content and botanical origin of Spanish honeys

Eleven elements (Zn, P, B, Mn, Mg, Cu, Ca, Ba, Sr, Na and K) were determined by inductively plasma coupled spectrometry in 40 honey samples from different places of Spain and four different botanical origins: Eucalyptus (Eucalyptus sp.), Heather (Erica sp.), Orange-blossom (Citrus sinensis) and Rosemary (Rosmarinus officinalis). K, Ca and P show the higher levels with average concentrations ranged between 434.1-1935 mg kg⁻¹ for K; 42.59-341.0 mg kg⁻¹ for Ca and 51.17-154.3 mg kg⁻¹ for P. Levels of Cu (0.531-2.117 mg kg⁻¹), Ba (0.106-1.264 mg kg⁻¹) and Sr (0.257-1.462 mg kg⁻¹) are the lowest in all honey samples. Zn (1.332-7.825 mg kg⁻¹), Mn (0.133-9.471 mg kg⁻¹), Mg (13.26-74.38 mg kg⁻¹) and Na (11.69-218.5 mg kg⁻¹) concentrations were found strongly dependent on the kind of botanical origin.Results were submitted to pattern recognition procedures, unsupervised methods such as cluster and principal components analysis and supervised learning methods like linear discriminant analysis in order to evaluate the existence of data patterns and the possibility of differentiation of Spanish honeys from different botanical origins according to their mineral content. Cluster analysis shows four clusters corresponding to the four botanical origins of honey and PCA explained 71% of the variance with the first two PC variables. The best-grouped honeys were those from heather; eucalyptus honeys formed a more dispersed group and finally orange-blossom and rosemary honeys formed a less distinguishable group.     

Development of new reference materials for the determination of cadmium,chromium, mercury and lead in polycarbonate

Reference materials for quantitative determination of Cd, Cr, Hg and Pb in polycarbonate were developed. Reference materials with two concentration level of elements were prepared by adding appropriate amounts of chemicals to a blank polycarbonate base material. It was shown that ten bottles with triplicate analysis are enough to demonstrate the homogeneity of these candidate reference materials. The statistical results also showed no significant trends in both short-term stability test for four weeks and long-term stability test for twelve months. The certification of the four elements was carried out by isotope-dilution-inductively coupled plasma mass spectrometry (ID-ICP-MS) with microwave-assisted digestion. Certification of candidate reference materials in a single laboratory was confirmed with interlaboratory comparison participated by a certain number of well-recognized testing laboratories in Korea. The certified values and expanded uncertainties (k = 2) for the candidate reference material with low level and the one with high level were (51.7 ± 2.1) mg kg⁻¹ Cd, (103.8 ± 2.9) mg kg⁻¹ Cd, (98.8 ± 4.5) mg kg⁻¹ Cr, (1004 ± 49.8) mg kg⁻¹ Cr, (107.4 ± 4.6) mg kg⁻¹ Hg, (1133 ± 50.7) mg kg⁻¹ Hg, (94.8 ± 3.7) mg kg⁻¹ Pb and (988.4 ± 53.6) mg kg⁻¹ Pb, respectively. The reference materials developed in this study demonstrated their suitability for the quality assurance in Cd, Cr, Hg and Pb analysis for the implementation of RoHS Directive.     

Quantification of isoorientin and total flavonoids in Passiflora edulis fruit pulp by HPLC-UV/DAD

A method is reported for the quantification of isoorientin (using a standard addition method) and total flavonoids (expressed as rutin, using the external standard method) in passion fruit pulp (Passiflora edulis Sims f. flavicarpa Degener, Passifloraceae). Extraction of flavonoids was optimized by experimental design methodology, and quantitative analysis was performed by high-performance liquid chromatography with photo-diode array detection (HPLC-UV/DAD). The method was developed and validated according to ICH requirements for specificity, linearity, accuracy, precision (repeatability and intermediate precision), LOD and LOQ. Rutin was chosen as standard for the quantification of total flavonoids in order to propose a HPLC method feasible for routine analysis of the flavonoids in the passion fruit pulp. The passion fruit pulp contained 16.226 ± 0.050 mg L^− 1 of isoorientin and 158.037 ± 0.602 mg L^− 1 of total flavonoid, suggesting that P. edulis fruits may be comparable with other flavonoid food sources such as orange juice or sugarcane juice.     

GC-EI-MS内标法分析鱼肉中邻苯二甲酸酯

鱼肉样品以Florisil硅藻土层析柱净化后, 经气相色谱-电子轰击离子源-质谱法(GC-EI-MS)分析其中8种邻苯二甲酸酯(PAEs)含量: 邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丙酯(DPrP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸丁基苄基酯(BBP)、邻苯二甲酸二戊酯(DPeP)、邻苯二甲酸二环己基酯(DCHP)、邻苯二甲酸二己酯(DHP)、邻苯二甲酸二(2-乙基己基)酯(DEHP). 比较了外标和内标法定量, 并确定苯甲酸苄基酯为内标物; 优化了提取剂、吸附剂和洗脱剂的种类, 以及洗脱体积等样品前处理方法; 尤其对分析空白的控制问题进行了详细讨论; 准确分析了5种鱼样品中此类物质含量. 该方法的线性范围为50.0～800 μg•L^－1, 相关系数(R)大于0.99986, 相对标准偏差(Relative standard deviation, RSD)均小于12.7%, 检测限(Limit of detection, LOD)低于3.66 μg•L^－1, 样品的加标回收率为74.0%～113%. 其线性范围、相关系数、准确度、精密度和LOD等指标均满足鱼肉中多种PAEs同时分析的要求.     

‘Total fluorine’ analysis of seed of Australian Gastrolobium spp. showing temporal, spatial and morphological variation

Alkali-fusion in conjunction with a fluoride selective electrode were used to quantify ‘total fluorine’, being organic fluorine + inorganic fluoride, for the seed of 13 species of Gastrolobium from south-west Western Australia. Intact seed covering spatial and temporal distributions, as well as G. bilobum, G. calycinum and G. parviflorum seed dissected into cotyledons and testa + aril, were analysed. Analysis found significant intra-and inter-species variation, both temporally and spatially, with intact seed concentrations ranging from 1.6 ± 0.3 mg kg⁻¹ in G. spinosum from Mundaring to 1063.9 ± 77.8 mg kg⁻¹ for G. cuneatum from Torbay. Approximately 87% of the ‘total fluorine’ was found to be in the seed cotyledons. Additional analysis detected little inorganic fluoride, indicating the majority of fluorine in the seed is organically bound. Parent compound(s) of the fluorine, seed toxicity and the implications of the results for seed chemical defense are discussed.     

Speciation of dissolved Fe(II) and Fe(III) in environmental water samples by micro-column packed with N-benzoyl-N-phenylhydroxylamine loaded on microcrystalline naphthalene and determination by electrothermal vaporization inductively coupled plasma-optical emission spectrometry

A novel solid phase extraction technique for the speciation of trace dissolved Fe(II) and Fe(III) in environmental water samples was developed by coupling micro-column packed with N-benzoyl-N-phenylhydroxylamine (BPHA) loaded on microcrystalline naphthalene to electrothermal vaporization inductively coupled plasma-optical emission spectrometry (ETV-ICP-OES). Various influencing factors on the separation and preconcentration of Fe(II) and Fe(III), such as the acidity of the aqueous solution, sample flow rate and volume, have been investigated systematically, and the optimized operation conditions were established. At pH 3.0 Fe(III) could be selectively retained by micro-column (20 mm × 1.4 mm, i.d.) packed with BPHA immobilized on microcrystalline naphthalene, and Fe(II) passed through the micro-column. Both Fe(II) and Fe(III) could be adsorbed by the micro-column at pH 6.5. Thus, the total Fe could be determined without the need for preoxidation of Fe(II) to Fe(III). The retained Fe(III) or the Fe(II) and Fe(III) was subsequently eluted by 0.1 ml of 1 mol l⁻¹ HCl. The adsorption capacity of the solid phase adsorption material was found to be 45.0 mg g⁻¹ for Fe(III) at pH 3.0 and 65.3 mg g⁻¹ for Fe(II) at pH 6.5, respectively. The detection limit (3σ) of 0.053 μg l⁻¹ was obtained with a practical enrichment factor of 156 at a sample volume of 17 ml. The relative standard deviations of 4.2% and 4.6% (C_Fe(III) = C_Fe(II) = 10 μg l⁻¹, n = 7) for Fe(III) and total iron were found, respectively. The method was successfully applied to the determination of trace Fe(II) and Fe(III) in environmental water samples (East Lake water, local tap water and mineral water). In order to validate the method, the developed method was applied to the determination of total iron in certified materials of NIES NO.10-b rice flour and GBW07605 tea leaves, and the results obtained were in good agreement with the certified values.     

Sequestration of Cu(II), Ni(II), and Co(II) by ethyleneimine immobilized on silica

Thermodynamic data on interaction of Cu(II), Ni(II), and Co(II) with silica modified with ethyleneimine are obtained by calorimetric titration. The amount of ethyleneimine anchored on silica surface was estimated to be 0.70 mmol g⁻¹. The enthalpies of binding Ni(II), Cu(II) and Co(II), are −3.59 ± 0.001, −4.88 ± 0.001, and −7.75 ± 0.003 kJ mol⁻¹, respectively.     

Simultaneous determination of neutral nitrogen compounds in gasoline and diesel by differential pulse voltammetry

The presence of trace neutral organonitrogen compounds as carbazole and indole in derivative petroleum fuels plays an important role in the car's engine maintenance. In addition, these substances contribute to the environmental contamination and their control is necessary because most of them are potentially carcinogenic and mutagenic. For those reasons, a reliable and sensitive method was proposed for the determination of neutral nitrogen compounds in fuel samples, such as gasoline and diesel using preconcentration with modified silica gel (Merck 70-230 mesh ASTM) followed by differential pulse voltammetry (DPV) technique on a glassy carbon electrode. The electrochemical behavior of carbazole and indole studied by cyclic voltammetry (CV) suggests that their reduction occurs via a reversible electron transfer followed by an irreversible chemical reaction. Very well resolved diffusion controlled voltammetric peaks were obtained in dimethylformamide (DMF) with tetrabutylammonium tetrafluoroborate (TBAF₄ 0.1 mol L⁻¹) for indole (−2.27 V) and carbazole (−2.67 V) versus Ag|AgCl|KCl_sat reference electrode. The proposed DPV method showed a good linear response range from 0.10 to 300 mg L⁻¹ and a limit of detection (L.O.D) of 7.48 and 2.66 μg L⁻¹ for indole and carbazole, respectively. The results showed that simultaneous determination of indole and carbazole presents in spiked gasoline samples were 15.8 ± 0.3 and 64.6 ± 0.9 mg L⁻¹ and in spiked diesel samples were 9.29 ± 1 and 142 ± 1 mg L⁻¹, respectively. The recovery was evaluated and the results shown the values of 88.9 ± 0.4 and 90.2 ± 0.8% for carbazole and indole in fuel determinations. The proposed method was also compared with UV-vis spectrophotometric measures and the results obtained for the two methods were in good agreement according to the F and t Student's tests.     

The use of Agrobacterium tumefacients immobilized on Amberlite XAD-4 as a new biosorbent for the column preconcentration of iron(III), cobalt(II), manganese(II) and chromium(III)

A microorganism Agrobacterium tumefacients as an immobilized cell on a solid support was presented as a new biosorbent for the enrichment of Fe(III), Co(II), Mn(II) and Cr(III) prior to flame atomic absorption spectrometric analysis. Amberlite XAD-4 was used as a support material for column preconcentration. Various parameters such as pH, amount of adsorbent, eluent type and volume, flow rate of sample solution, volume of sample solution and matrix interference effect on the retention of the metal ions have been studied. The optimum pH for the sorption of above mentioned metal ions were about 6, 8, 8 and 6, respectively. The loading capacity of adsorbent for Co(II) and Mn(II) were found to be 29 and 22 μmol g⁻¹, respectively. The recoveries of Fe(III), Co(II), Mn(II) and Cr(III), under the optimum conditions were found to be 99 ± 3, 99 ± 2, 98 ± 3 and 98 ± 3%, respectively, at the 95% confidence level. The limit of detection was 3.6, 3.0, 2.8 and 3.6 ng ml⁻¹ for Fe(III), Co(II), Mn(II) and Cr (III), respectively, by applying a preconcentration factor of 25. The proposed enrichment method was applied for metal ion determination from water samples, alloy samples, infant foods and certified samples such as whey powder (IAEA-155) and aluminum alloy (NBS SRM 85b). The analytes were determined with a relative error lower than 10% in all samples.     

Determination of selenium using atomically imprinted polymer (AIP) and hydride generation atomic absorption spectrometry

This paper describes selenium determination based on Se⁰ preconcentration in the imprinted polymer (synthesized with 2.25 mmol SeO₂, 4-vinylpyridine and 1-vinylimidazole) with subsequent detection on-line in HG-FAAS. During the synthesis, SeO₂ is reduced to Se (0). Therefore, there are no MIP neither IIP in the present work, thus we denominated: AIP, i.e., atomically imprinted polymers. For the optimization of analytical parameters Doehlert design was used. The method presented limit of detection and limit of quantification of 53 and 177 ng L⁻¹, respectively, and linear range from 0.17 up to 6 μg L⁻¹ (r = 0.9936). The preconcentration factor (PF), consumptive index (CI) and concentration efficiency (CE) were 232; 0.06 mL and 58 min⁻¹ respectively. The proposed method was successfully applied to determine Se in Brazil nuts (0.33 ± 0.03 mg kg⁻¹), apricot (0.46 ± 0.02 mg kg⁻¹), white bean (0.47 ± 0.03 mg kg⁻¹), rice flour (0.47 ± 0.02 mg kg⁻¹) and milk powder (0.22 ± 0.01 mg kg⁻¹) samples. It was possible to do 12 analyzes per hour. Accuracy was checked and confirmed by analyzing certified reference material (DORM-2, dogfish muscle), and samples precision was satisfactory with RSD lower than 10%.     

A novel potentiometric biosensor for selective L-cysteine determination using L-cysteine-desulfhydrase producing Trichosporon jirovecii yeast cells coupled with sulfide electrode

Trichosporon jirovecii yeast cells are used for the first time as a source of l-cysteine desulfhydrase enzyme (EC 4.4.1.1) and incorporated in a biosensor for determining l-cysteine. The cells are grown under cadmium stress conditions to increase the expression level of the enzyme. The intact cells are immobilized on the membrane of a solid-state Ag₂S electrode to provide a simple l-cysteine responsive biosensor. Upon immersion of the sensor in l-cysteine containing solutions, l-cysteine undergoes enzymatic hydrolysis into pyruvate, ammonia and sulfide ion. The rate of sulfide ion formation is potentiometrically measured as a function of l-cysteine concentration. Under optimized conditions (phosphate buffer pH 7, temperature 37 ± 1 °C and actual weight of immobilized yeast cells 100 mg), a linear relationship between l-cysteine concentration and the initial rate of sulfide liberation (dE/dt) is obtained. The sensor response covers the concentration range of 0.2-150 mg L⁻¹ (1.7-1250 μmol L⁻¹) l-cysteine. Validation of the assay method according to the quality control/quality assurance standards (precision, accuracy, between-day variability, within-day reproducibility, range of measurements and lower limit of detection) reveals remarkable performance characteristics of the proposed biosensor. The sensor is satisfactorily utilized for determination of l-cysteine in some pharmaceutical formulations. The lower limit of detection is ∼1 μmol L⁻¹ and the accuracy and precision of the method are 97.5% and ±1.1%, respectively. Structurally similar sulfur containing compounds such as glutathione, cystine, methionine, and d-cysteine do no interfere.     

Accelerated solvent-based extraction and enrichment of selected plasticisers and 4-nonylphenol, and extraction of tin from organotin sources in sediments, sludges and leachate soils

Enrichment techniques have become an important feature in the trace analysis of oestrogen mimicking chemicals in the environment. Recent developments such as accelerated solvent extraction (ASE) have improved extraction recoveries in a wide variety of solid matrices including sediments, sludges and leachate soils. Such samples taken from the Irish Midlands Shannon Catchment region during the winter of 2004/5 and suspected to contain certain xenooestrogens or hormonally active agents were extracted using this technique, which was then coupled with high performance liquid chromatography (HPLC) for quantification purposes. ASE was thus employed to both isolate and pre-concentrate targeted analytes using the minimum amount of solvent hence making extractions more conservational. Two simple, yet extremely sensitive liquid chromatographic methods were developed based on UV detection; one for phthalates and one for alkylphenols, with recoveries reaching up to 92.0%. Acid digestion was used for the extraction of the tin and organotin compounds with analysis by polarography. In river sediment, levels of up to 24.4 mg kg⁻¹ phthalate, 1.14 mg kg⁻¹ 4-nonylphenol and 118 mg kg⁻¹ tin were found. In leachate sediments, values up to 49.8 mg kg⁻¹ phthalate, 1.57 mg kg⁻¹ 4-nonylphenol, and 36.0 mg kg⁻¹ tin were determined. In sludge, values up to 174 mg kg⁻¹ phthalate and 22.8 mg kg⁻¹ 4-nonylphenol were quantified. The highest value of tin (118 mg kg⁻¹) was found present in an area of high leisure craft activity. Typical sediment levels of tin at other river locations ranged between 1.20 and 37.5 mg kg⁻¹.     

A rapid quantitative method for humic substances determination in natural waters

A simple and rapid method was proposed for humic substances (HS) determination at microgram levels in natural waters. This assay method is based on the binding of a dye, Toluidine Blue (TB), to HS molecules to produce a dye-HS complex, which causes a decrease in absorbance at 630 nm. This method was calibrated with HS samples with up to a concentration of 40 mg L⁻¹, which covered the range of dissolved HS concentrations present in natural waters. The detection limit was 0.8 mg L⁻¹ of HS, and the relative standard deviation of 10 replicate measurements for a 20-mg L⁻¹ standard sample was 3.5%. From the Langmuir adsorption isotherm theory, the binding equilibrium constant and total number of binding sites at neutral pH were calculated to be (8.17 ± 0.42) × 10⁵ L mol⁻¹ and N of 1.45 ± 0.04 mmol g⁻¹ HS, respectively. The determination results with five water samples from lake, river and pond were consistent with those measured with the reference methods, demonstrating that this quantification method for HS determination was rapid, sensitive and feasible.