Sensor film for Vitamin C determination based on absorption properties of polyaniline

An analytical method based on the absorption changes of chemically polymerised polyaniline at 700 nm is proposed for the determination of Vitamin C. Vitamin C produces a polyaniline film reduction, originating changes in its absorbance proportional to the Vitamin C concentration. The optimum reaction conditions and the analytical characteristics have been studied. The linear response of the method ranged from 0.10 to 1.0 mg l⁻¹ for a 6 min reaction time and from 1.0 to 8.0 mg l⁻¹ for a 2 min reaction time. Reproducibility, expressed as the coefficient of variation, was 0.8% (6 min reaction time) and 2.3% (2 min reaction time) (n = 10). The method has been applied to Vitamin C determination in pharmaceutical preparations and commercial fruit juices. The results were compared with those obtained by the 2,6-dichlorophenolindophenol titration method (the AOAC Official Method) and no systematic errors were observed.     

A simple detection system for gas chromatography based on molecular absorption spectrometry in the gas phase

Summary A simple and inexpensive detection system for gas chromatography, based on gas-phase, molecular absorption measurements, is presented in which the chromatographic column is directly joined to the spectrophotometer flow cell, without heated transfer lines. A mixture of eight benzene compounds (including methyl, halogen and nitrogen derivatives) were separated and analyzed. Parameters affecting separation (temperature program and carrier gas flow) and measurement quality (wavelength and integration time) were studied and a measurement program designed to modify the wavelength during chromatography. The analytical characteristics of each compound were calculated, obtaining detection limits ranging from 0.5 to 9 g mL^–1. Finally, the method was applied to several synthetic mixtures, with good results.     

Micelle mediated methodology for the determination of free and bound iron in wines by flame atomic absorption spectrometry

A methodology utilizing the cloud point phenomenon for the determination of free and tannin-bound iron in wines is presented. The method employs precipitation of the tannins and other phenolic and insoluble compounds in the micelles of a non-ionic surfactant mixture (TX-100 and TX-45) upon increase of the solution temperature, which are subsequently separated from the initial solution by centrifugation. The surfactant-rich-phase containing the tannins and the insoluble iron fraction is directly aspirated into the nebulizer of a flame atomic absorption spectrometer after its uptake with a methanolic solution of HNO₃. The supernatant is submitted to the same cloud point extraction procedure for the determination of free iron species in the presence of a chelating agent, ammonium pyrrolidine dithiocarbamate (APDC), in order to form water-insoluble complexes with free iron. The complexes are extracted in the micelles and directly analyzed after they are diluted in a methanolic solution as described above. The total content of iron was also determined by conventional methods for comparison, yielding satisfactory results.The calibration graph was rectilinear up to 0.35 mg l⁻¹ Fe, with detection limits of 0.02 mg l⁻¹ with a relative standard deviation of 2.4%. The method was successfully applied to red and white wines.     

Effect of polymerization temperature on polyaniline based electrorheological suspensions

As one of the intrinsically polarizable materials used in electrorheological (ER) fluid, polyaniline was synthesized by the chemical oxidation of aniline with ammonium peroxysulfate. ER fluids were prepared by dispersing polyaniline particles in silicone oil, and their rheological properties were measured. The effect of the polymerization temperature of polyaniline on its ER characteristics was investigated. ER fluids with polyaniline particles synthesized at −10°C (PA-10) showed the best ER performance (yield stress) compared with those synthesized at higher temperatures. A difference in the flow behavior of the ER fluids was also investigated through the dielectric spectra of ER fluids. Received: 24 March 1988 Accepted: 3 August 1998     

Inside needle capillary adsorption trap device for headspace solid-phase dynamic extraction based on polyaniline/hexagonally ordered silica nanocomposite

Highly porous polyaniline/hexagonally ordered silica sorbent was used for fabrication of the inside needle capillary adsorption trap (INCAT) device. Polyaniline/SBA-15 nanocomposite was synthesized via chemical polymerization technique. The fabricated INCAT device was evaluated to the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography (GC)-mass spectrometry (MS). A one at-the-time optimization strategy was applied for optimizing the important extraction parameters such as extraction temperature, extraction time, ionic strength, sampling flow rate, desorption time, and desorption temperature. In optimum conditions (extraction temperature 55 °C, extraction time 20 min, ionic strength 20% (w/v), flow rate 4.5 mL min(-1), desorption temperature 270 °C, desorption time 3 min) the repeatability for one INCAT device (n = 4), expressed as relative standard deviation, was between 4.2 and 10.2% for the tested compounds. The quantitation limits for the studied compounds were between 1 and 5 pg mL(-1). The developed method was successfully applied to spring water sample which was spiked with PAHs with the relative recovery percentages of 87.3-109.1%. The developed method offers the advantage of being simple to use, with shorter analysis times, lower cost of equipment, and thermal stability.     

Near-infrared and multicolor electrochromic device based on polyaniline derivative

Electroactive conducting copolymers of aniline(ANI) and diphenylamine(DPA) are prepared on indium tin oxide(ITO) surface from 1 mol/L H2SO4 aqueous solution with different feed ratios of ANI to DPA by using a potentiostatic method. FTIR spectra and SEM measurements are used to confirm the formation of copolymers. Due to the combination of the N,N′-diphenyl benzidine and aniline units in the molecular chain, the copolymer films exhibit improved electrochemical and electrochromic properties, compared to PANI and PDPA. The copolymer [marked as P(ANI9-co-DPA1)] film prepared at a ratio of 9:1(ANI/DPA) exhibits novel transmittance modulation both in visible and near-infrared(NIR) region between -0.8 V and 0.8 V(52% and 67% respectively) and fast response time(3.6 s for coloration and 2.3 s for bleaching at 600 nm). An electrochromic device(ECD) based on P(ANI9-co-DPA1) and PEDOT:PSS is also fabricated and shows a multicolor electrochromic performance, with a good optical contrast(29% in visible region and 40% in NIR region), acceptable response time(8.3 s for coloration and 7.5 s for bleaching at 600 nm) and long-term stability. Clear color changes from transparent(-0.8 V), bright green(0 V), seagreen(0.4 V) to dark slate gray(0.8 V) are demonstrated.     

Conductive composites based on core–shell polyaniline nanoclay by latex blending

A simple and versatile method for the preparation of conductive composites based on core–shell polyaniline (PANI) one-dimensional nanoclay distributed in poly(ethylene-vinyl acetate) (EVA) latex with high colloidal stability is demonstrated. The morphological and electrical properties of the composites were investigated. The nanostructures were synthesized from PANI-coated sepiolite nanorods via in situ oxidative polymerization after the surface modification of the sepiolite with ammonium and anilinium salts. Two forms of PANI nanoclay, powder and paste, have shown a much different percolation threshold and significantly different morphologies due to their dispersion ability in EVA matrix. At the same PANI content, the conductivity of the blends with paste is much higher than that of blends with powder PANI nanoclay.     

Method development for the determination of lead in wine using electrothermal atomic absorption spectrometry comparing platform and filter furnace atomizers and different chemical modifiers

A method has been developed for the determination of lead in wine by electrothermal atomic absorption spectrometry without any sample preparation and calibration against aqueous standards, using 7.5 μg Pd as a chemical modifier. The results obtained for seven wines using the proposed method and an acid digestion procedure did not show any significant difference using a Student's t-test. Atomization in a transversally heated filter atomizer (THFA) was compared with atomization in a conventional transversally heated platform furnace. The former provided a 2.6-fold higher sensitivity, improving the characteristic mass from 34 to 12 pg and a 1.6-fold better limit of detection (0.3 μg L⁻¹ compared to 0.5 μg L⁻¹) for aqueous solutions using the same injection volume of 20 μL. However, the average precision, expressed as the relative standard deviation for the determination of lead in wine under routine conditions was improved from 4.6% with platform atomization to 0.6% in the THFA. The lead content found in seven arbitrarily chosen white and red wines, five from Brazil, one from Chile and one from Spain, ranged from 6 to 60 μg L⁻¹ Pb with an average content of 11.4 μg L⁻¹ Pb for the wines from South America.     

A practical method for the determination of sulphur in coal samples by high-resolution continuum source flame atomic absorption spectrometry

Sulphur in coal was determined using a high-resolution continuum source flame atomic absorption spectrophotometer (HR-CS-FAAS) with actylene/air flame. The C-S absorption band at 258.056 nm was found the most suitable analytical line with respect to sensitivity and spectral interferences. The instrumental parameters were optimized. The coal samples were dried and dissolved using microwave-assisted digestion technique. The validity of the method was tested using standard reference material and certified values were found in the limits of 95% confidence level. Since the concentrations of matrix elements of coal other than carbon are low enough not to cause any spectral interferences, the linear calibration method was applied in all quantifications without any problem. The calibration standards were prepared in sulphuric acid. The method was accurate, fast, simple and sensitive. The limit of detection (LOD, 3δ, N = 10) and the limit of quantification (LOQ, 10δ, N = 10) were found to be 0.01 and 0.03% (w/w), respectively. The sulphur concentrations of various kinds of the coal samples received around Turkey were determined. The sulphur contents of the coal samples were ranged from ≤LOQ to 1.2%.     

Application of tandem column solid phase extraction and flame atomic absorption spectrometry for the determination of inorganic and organically bound forms of iron in wine

A tandem column solid phase extraction (SPE) procedure has been devised to examine the fractionation of Fe in wine. Wine was filtered through a 0.45 μm filter and then, the filtrate was driven through an adsorbing Amberlite XAD-7HP column followed by a cation exchange Dowex 50W-x8-200 column. Three different Fe groupings are discriminated and assessed, including hydrophobic species of Fe bound to phenolic substances and related species (phenolic fraction), cationic species comprising simple Fe ions and labile Fe forms (cationic fraction), in addition to anionic and/or neutral Fe complexes with organic acids (residual fraction). The suitability of the procedure has been evaluated analyzing four bottled red wines. The results obtained were verified using another tandem column assemblage in which an adsorbing Amberlite XAD-16 column was exchanged by the Amberlite XAD-7HP column. The fractionation pattern ascertained for Fe in analyzed wines is discussed in reference to previously published works. In addition, a conditioning treatment and preparation of Amberlite XAD resins have been revised.     

Determination of sulfur forms in wine including free and total sulfur dioxide based on molecular absorption of carbon monosulfide in the air–acetylene flame

A new method for the determination of sulfur forms in wine, i.e., free SO₂, total SO₂, bound SO₂, total S, and sulfate, is presented. The method is based on the measurement of the carbon monosulfide (CS) molecular absorption produced in a conventional air–acetylene flame using high-resolution continuum source absorption spectrometry. Individual sulfur forms can be distinguished because of the different sensitivities of the corresponding CS molecular absorption. The sensitivity of free SO₂ is about three times higher than the value for bound SO₂ and sulfate. The method makes use of procedures similar to those used in classic reference methods. Its performance is verified by analyzing six wine samples. Relative standard deviations are between 5 and 13% for free SO₂ and between 1 and 3% for total SO₂. For the validation of the accuracy of the new method, the results are compared with those of reference methods. The agreement of the values for total SO₂ with values of the classic method is satisfactory: five out of six samples show deviations less than 16%. Due to the instability of free SO₂ in wine and the known problems of the used reference method, serious deviations of the free SO₂ results are found for three samples. The evaluation of the limits of detection focuses on the value for free SO₂, which is the sulfur form having by far the lowest concentration in wine. Here, the achievable limit of detection is 1.8 mg L⁻¹. Figure Detection of non-metal elements using continuum source flame absorption spectrometry     

Optimisation and characterisation of biosensors based on polyaniline

With lower limits of detection and increased stability constantly being demanded of biosensor devices, characterisation of the constituent layers that make up the sensor has become unavoidable, since this is inextricably linked with its performance. This work describe the optimisation and characterisation of two aspects of sensor performance: a conductive polymer layer (polyaniline) and the immobilised protein layer. The influence of the thickness of polyaniline films deposited electrochemically onto screen-printed electrode surfaces is described in this work in terms of its influence on a variety of amperometric sensor performance characteristics: time to reach steady state, charging current, catalytic current, background current and signal/background ratios. The influence of polymer film thickness on the conductivity and morphology of finished films is also presented.

An electrostatic method of protein immobilisation is used in this work and scanning electron microscopy in conjunction with gold-labelled antibodies and back-scattered electron detection has enabled the direct visualisation of individual groups of proteins on the sensor surface. Such information can provide an insight into the performance of sensors under influence of increasing protein concentrations.     

Solid‐phase microextraction based on polyaniline doped with perfluorooctanesulfonic acid coupled to HPLC for the quantitative determination of chlorophenols in water samples

A porous and highly efficient polyaniline‐based solid‐phase microextraction (SPME) coating was successfully prepared by the electrochemical deposition method. A method based on headspace SPME followed by HPLC was established to rapidly determine trace chlorophenols in water samples. Influential parameters for the SPME, including extraction mode, extraction temperature and time, pH and ionic strength procedures, were investigated intensively. Under the optimized conditions, the proposed method was linear in the range of 0.5–200 μg/L for 4‐chlorophenol and 2,4,6‐trichlorophenol, 0.2–200 μg/L for 2,4‐dichlorophenol and 2–200 μg/L for 2,3,4,6‐tetrachlorophenol and pentachlorophenol, with satisfactory correlation coefficients (>0.99). RSDs were <15% (n = 5) and LODs were relatively low (0.10–0.50 μg/L). Compared to commercial 85 μm polyacrylate and 60 μm polydimethylsiloxane/divinylbenzene fibers, the homemade polyaniline fiber showed a higher extraction efficiency. The proposed method has been successfully applied to the determination of chlorophenols in water samples with satisfactory recoveries.     

Multiresidue determination of pesticides from aquatic media using polyaniline nanowires network as highly efficient sorbent for microextraction in packed syringe

A simple, rapid and sensitive method based on microextraction in packed syringe (MEPS), in combination with gas chromatography–mass spectrometry (GC–MS) was developed. Polyaniline (PANI) nanowires network was synthesized and used as sorbent of MEPS for the multiresidue determination of selected analytes from triazine, organochlrorine and organophosphorous pesticides in aqueous samples. The PANI nanowires network was prepared using soft template technique and its characterization was studied by scanning electron microscopy (SEM). The presence of micelles in this methodology showed to be an important parameter in shaping the growing polymer. Hexadecyltrimethylammonium bromide (HTAB) was used as structure directing agent in PANI preparation procedure and this was led to the formation of nanowires with diameters ranging from 35 nm to 45 nm. The synthesized PANI nanowires network showed higher extraction capability in comparison with the bulk PANI. Important parameters influencing the extraction and desorption processes including desorption solvent, elution volume, draw–eject cycles of sample, draw–eject mode, pH effect and amount of sorbent were optimized. Limits of detection were in the range of 0.07–0.3 ng mL⁻¹ using time scheduled selected ion monitoring (SIM) mode. The linearity of method was in the range from 0.5–200 ng mL⁻¹ to 0.2–1000 ng mL⁻¹. The method precision (RSD %) with three replicates were in the range of 5.3–18.4% at the concentration level of 5 ng mL⁻¹. The developed method was successfully applied to the Zayandeh-rood river water samples and the matrix factor obtained for the spiked real water samples were in the range of 0.79–0.94.     

A fast and sensitive continuous flow nanobiodetector based on polyaniline nanofibrils

Polyaniline nanofibrils, fabricated as a freestanding nanonetwork in a micro gap between two gold electrodes, have been applied in a fast and sensitive analytical device for detecting microorganism cells in a flowing liquid, including the “on-line” regime. The electrical response of the device (in this case an increase in the electrical conductivity of the nanonetwork) depends on the number of cells in the sample analyzed: it is linear within the range of 0–5000 and 0–15 × 10⁶ cells injected for yeast and bacteria examined, respectively. The detection limit depends on the type of microorganism: it is about 300 and 1.9 × 10⁵ (per mL) for yeast (Saccharomyces cerevisiae) and bacteria cells (Lactobacillus rhamnosus), respectively. The results are registered within few seconds (typically 5–15 s). The device is designed to detect a low level of bio-contamination and it is expected to be useful in biomedical applications, environmental protection and anti bioterrorism systems, including “on-line” monitoring.     

An automatic gas-phase molecular absorption spectrometric system using a UV-LED photodiode based detector for determination of nitrite and total nitrate

An automatic gas-phase molecular absorption spectrometric (GPMAS) system was developed and applied to determine nitrite and total nitrate in water samples. The GPMAS system was coupled with a UV-light emitting diode photodiode (UV-LED-PD) based photometric detector, including a 255 nm UV-LED as the light source, a polyvinyl chloride (PVC) tube of 14 cm as the gas flow cell, and an integrated photodiode amplifier to measure the transmitted light intensity. The UV-LED-PD detector was compact, robust, simple and of low heat production, comparing with detectors used in other GPMAS works. For nitrite measurement, citric acid was used to acidify the sample, and ethanol to catalyze the quantitative formation of NO₂. The produced NO₂ was purged with air flow into the UV-LED-PD detector, and the gaseous absorbance value was measured. The total nitrate could be determined after being reduced to nitrite with a cadmium column. Limits of detection for nitrite and nitrate were 7 μmol/L and 12 μmol/L, respectively; and linear ranges of 0.021-5 mmol/L for nitrite and 0.036-4 mmol/L for nitrate were obtained. Related standard deviations were 1.81% and 1.08% for nitrite and nitrate, respectively, both at 2 mmol/L. The proposed method has been applied to determine nitrite and total nitrate in some environmental water samples.     

Automatic flow system for the sequential determination of copper in serum and urine by flame atomic absorption spectrometry

In this work, a fully automated flow system exploiting the advantages of the association of multi-pumping, multicommutation, binary sampling and merging zones, to accomplish the sequential determination of copper in serum and urine by flame atomic absorption spectrometry, is described. The developed flow system allowed multiple tasks, such as serum samples preparation (samples and standard solutions viscosity adjustment), serum copper (SCu) measurement, urine copper (UCu) pre-concentration and its subsequent elution and measurement, to be carried out sequentially. The implemented flow manifold presented a modular configuration consisting on two quasi-independent modules, each one accountable for a specific sample manipulation and whose combined operation under computer control enabled the determination of copper in a wide concentrations range.Once optimised and with a sample consumption of about 0.250 mL of serum and 7 mL of urine, the developed flow system allowed linear calibration plots up to 5 mg L⁻¹ with a detection limit of 0.035 mg L⁻¹ for SCu and linear calibration plots up to 300 μg L⁻¹ with a detection limit of 0.67 μg L⁻¹ for UCu. The sampling rate varied according to the module employed and was about 360 determinations h⁻¹ (SCu module), 12 determinations h⁻¹ (UCu module) or 24 determinations h⁻¹ (12 urine and 12 serum samples; UCu and SCu modules simultaneously). Repeatability studies (R.S.D.%, n = 10) showed good precision for UCu at concentrations of 25 μg L⁻¹ (2.54%), 50 μg L⁻¹ (0.90%) and 100 μg L⁻¹ (1.62%) as well as for SCu at concentrations of 0.25 mg L⁻¹ (8.11%), 1 mg L⁻¹ (3.11%) and 5 mg L⁻¹ (0.90%). A comparative evaluation showed a good agreement between the results obtained in the analysis of UCu and SCu (n = 18) by both the developed methodology and the reference procedures. Accuracy was further evaluated by means of the analysis of reference samples (Seronorm™ Trace Elements Urine and Seronorm™ Trace Elements Serum) and the obtained results complied with the certified values.     

Continuous ultrasound-assisted extraction coupled to a flow injection-flame atomic absorption spectrometric system for calcium determination in seafood samples

Calcium was extracted on-line from solid seafood samples by a simple and rapid continuous ultrasound-assisted extraction system. This system is connected to a flow injection manifold, which allows the on-line flame atomic absorption spectrometric determination of calcium. This method enables the analysis of solid samples avoiding time-consuming traditional sample preparation methods and their inherent errors. The on-line manifold for calcium determination is the simplest possible, because a volume of 250 L of acid extract is injected into an ultrapure water carrier stream. The acid extract was diluted on-line with lanthanum, which also acts as masking agent in order to avoid chemical interferences. The continuous monitoring of the calcium signal was accomplished by flame atomic absorption spectrometry. A Plackett-Burman experimental design was used for the optimisation of the continuous leaching procedure. The method allowed a total sampling frequency of 40 samples per hour, with a relative standard deviation for the complete procedure of 0.9% (for a sample containing 3414.35 mg/kg calcium (dry mass)). The limit of detection was found to be 44.4 mg/kg (dry mass) for 5 mg of sample. The analytical procedure was applied to real seafood samples.     

Thermal and structural stability of composite systems based on polyaniline deposited on porous polyethylene films

Conducting composite systems containing polyaniline layers produced on the surface and inside the pores of polyethylene support have been prepared. Microporous polyethylene films were obtained by melt extrusion with subsequent annealing, uniaxial extension, and thermal fixation. Polyaniline layers were formed by in-situ polymerization of aniline onto polyethylene porous support placed into the aqueous reaction mixture. Structural and chemical transformations upon heating of these systems in air in free state and in vacuum under load have been investigated by thermo-mechanical tests, IR spectrometry, and electron microscopy. Changes in mechanical properties of composites after heating have been analyzed. Composite systems have been found to demonstrate a considerably lower shrinkage upon heating than microporous polyethylene substrates. It has been discovered that the composites preserve mechanical integrity on heating up to temperatures much higher than the polyethylene melting point. It is concluded that thermo-mechanical behaviour of the composites is determined by the space-continuous phase of polyaniline on the surface and in the bulk of polyethylene support.     

An elastomeric conducting composite based on polyaniline coated nylon fiber and chloroprene rubber

Chloroprene rubber-polyaniline (PANI) coated nylon fiber composites containing PANI powder were prepared by mechanical mixing on a two-roll mill. PANI was synthesized by chemical polymerization of aniline in presence of hydrochloric acid. PANI coated nylon fiber was prepared by in situ polymerization of aniline on nylon fiber. The cure parameters cure kinetics, filler dispersion, mechanical properties, DC electrical conductivity and thermal degradation parameters of the composites were evaluated. Cure rate index and cure reaction constants indicated that the rate of cure reaction changes on filler addition. Filler addition at higher loadings led to agglomeration. The tensile strength and modulus values increased suggesting a reinforcement effect. The conductivity, thermal characteristics and thermal degradation kinetic parameters are also presented.