Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

Glucose and urea biosensors based on all solid-state PVC-NH2 membrane electrodes

Miniaturized urea and glucose sensors prepared by immobilization of glucose oxidase or urease directly onto all solid-state contact PVC-NH₂ membrane ammonium and hydrogen ion selective electrodes are described. The resulting biosensing membranes function equivalently to normal PVC membranes in terms of potentiometric response properties. The most important features of the glucose and urea sensors were high sensitivity, long life-time, easily built at a low cost, micro-construction and short response time. The characteristics of the glucose and urea sensors were examined in several buffer solutions at different concentrations and pH values. The influence of immobilization conditions on the dynamic response properties and life-time of the electrodes was studied. Under optimal conditions, the urea electrode showed a linear response between 5×10⁻² and 5×10⁻⁴ M urea, while the glucose electrode showed a linear response between 5×10⁻² and 1×10⁻⁴ M glucose.     

Composite film of carbon nanotubes and chitosan for preparation of amperometric hydrogen peroxide biosensor

A new amperometric biosensor for hydrogen peroxide was developed based on cross-linking horseradish peroxidase (HRP) by glutaraldehyde with multiwall carbon nanotubes/chitosan (MWNTs/chitosan) composite film coated on a glassy carbon electrode. MWNTs were firstly dissolved in a chitosan solution. Then the morphology of MWNTs/chitosan composite film was characterized by field-emission scanning electron microscopy. The results showed that MWNTs were well soluble in chitosan and robust films could be formed on the surface. HRP was cross-linked by glutaraldehyde with MWNTs/chitosan film to prepare a hydrogen peroxide biosensor. The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for H₂O₂ in the absence of a mediator. The linear range of detection towards H₂O₂ (applied potential: −0.2 V) was from 1.67 × 10⁻⁵ to 7.40 × 10⁻⁴ M with correction coefficient of 0.998. The biosensor had good repeatability and stability for the determination of H₂O₂. There were no interferences from ascorbic acid, glucose, citrate acid and lactic acid.     

Synergistic effect of mediator–carbon nanotube composites for dehydrogenases and peroxidases based biosensors

Very sensitive, low cost and reliable NADH and H₂O₂ sensors were realised and used for development of enzyme based biosensors. The active surface of the electrodes was modified with a nanocomposite obtained by modification of SWNT with a proper mediator: Meldola Blue (for NADH) and Prussian Blue (for H₂O₂). Low applied potential of − 50 mV vs. Ag/AgCl reference electrode proved the synergistic effect of nanocomposite materials towards NADH and H₂O₂ detection. Biosensors for malic acid and alkylphenols have been developed, using mediator-functionalised-SWNT-based electrodes and two different classes of enzymes: NAD⁺-dependent dehydrogenases and peroxidases. Immobilization of the enzymes was realised using a series of different procedures — adsorption, Nafion membrane, sol–gel and glutaraldehyde, in order to find the best configuration for a good operational stability. A higher sensitivity comparing with other reported biosensors of about 12.41 mA/M·cm² was obtained for l-malic acid biosensor with enzyme immobilised in Nafion membrane. Phenol, 4-t-octylphenol and 4-n-nonylphenol were used as standard compounds for HRP based biosensor. Fast biosensor response and comparable detection limit with HPLC methods were achieved.     

A novel nonenzymatic sensor based on LaNi0.6Co0.4O3 modified electrode for hydrogen peroxide and glucose

In this paper, LaNi_0.6Co_0.4O₃ (LNC) nanoparticles were synthesized by the sol–gel method, and the structure and morphology of LNC nanoparticles were characterized by X-ray diffraction spectrum, scanning electron microscopy and transmitting electron microscopy. And then, LNC was used to modify carbon paste electrode (CPE) without any adhesive to fabricate hydrogen peroxide and glucose sensor, and the results demonstrated that LNC exhibited strong electrocatalytical activity by cyclic voltammetry and amperometry. In H₂O₂ determination, linear response was obtained in the concentration range of 10 nM–100 μM with a detection limit of 1.0 nM. In glucose determination, there was the linear region of 0.05–200 μM with a detection limit of 8.0 nM. Compared with other reports, the proposed sensor also displayed high sensitivity toward H₂O₂ (1812.84 μA mM⁻¹ cm⁻²) and glucose (643.0 μA mM⁻¹ cm⁻²). Moreover, this prepared sensor was applied to detect glucose in blood serum and hydrogen peroxide in toothpaste samples with satisfied results, indicating its possibility in practical application.     

Immobilization of [Cu(bpy)2]Br2 complex onto a glassy carbon electrode modified with α-SiMo12O40 and single walled carbon nanotubes: Application to nanomolar detection of hydrogen peroxide and bromate

A simple procedure has been used for preparation of modified glassy carbon electrode with carbon nanotubes and copper complex. Copper complex [Cu(bpy)₂]Br₂ was immobilized onto glassy carbon (GC) electrode modified with silicomolybdate, α-SiMo₁₂O₄₀⁴⁻ and single walled carbon nanotubes (SWCNTs)_. Copper complex and silicomolybdate irreversibly and strongly adsorbed onto GC electrode modified with CNTs. Electrostatic interactions between polyoxometalates (POMs) anions and Cu-complex, cations mentioned as an effective method for fabrication of three-dimensional structures. The modified electrode shows three reversible redox couples for polyoxometalate and one redox couple for Cu-complex at wide range of pH values. The electrochemical behavior, stability and electron transfer kinetics of the adsorbed redox couples were investigated using cyclic voltammetry. Due to electrostatic interaction, copper complex immobilized onto GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ electrode shows more stable voltammetric response compared to GC/CNTs/Cu-complex modified electrode. In comparison to GC/CNTs/Cu-complex the GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ modified electrodes shows excellent electrocatalytic activity toward reduction H₂O₂ and BrO₃⁻ at more reduced overpotential. The catalytic rate constants for catalytic reduction hydrogen peroxide and bromate were 4.5(±0.2) × 10³ M⁻¹ s⁻¹ and 3.0(±0.10) × 10³ M⁻¹ s⁻¹, respectively. The hydrodynamic amperommetry technique at 0.08 V was used for detection of nanomolar concentration of hydrogen peroxide and bromate. Detection limit, sensitivity and linear concentration range proposed sensor for bromate and hydrogen peroxide detection were 1.1 nM and 6.7 nA nM⁻¹, 10 nM-20 μM, 1 nM, 5.5 nA nM⁻¹ and 10 nM-18 μM, respectively.     

Polymerized Nile Blue derivatives for plasticizer-free fluorescent ion optode microsphere sensors

Lipophilic H⁺-selective fluorophores such as Nile Blue derivatives are widely used in ISE-based pH sensors and bulk optodes, and are commonly dissolved in a plasticized matrix such as PVC. Unfortunately, leaching of the active sensing ingredients and plasticizer from the matrix dictates the lifetime of the sensors and hampers their applications in vivo, especially with miniaturized particle based sensors. We find that classical copolymerization of Nile Blue derivatives containing an acrylic side group gives rise to multiple reaction products with different spectral and H⁺-binding properties, making this approach unsuitable for the development of reliable sensor materials. This limitation was overcome by grafting Nile Blue to a self-plasticized poly(n-butyl acrylate) matrix via an urea or amide linkage between the Nile Blue base structure and the polymer. Optode leaching experiments into methanol confirmed the successful covalent attachment of the two chromoionophores to the polymer matrix. Both polymerized Nile Blue derivatives have satisfactory pH response and appropriate optical properties that are suitable for use in ion-selective electrodes and optodes. Plasticizer-free Na⁺-selective microsphere sensors using the polymerized chromoionophores were fabricated under mild conditions with an in-house sonic microparticle generator for the measurement of sodium activities at physiological pH. The measuring range for sodium was found as 10⁻¹-10⁻⁴ M and 1-10⁻³ M, for Nile Blue derivatives linked via urea and amide functionalities, respectively, at physiological pH. The observed ion-exchange constants of the plasticizer-free microsphere were log K_exch = −5.6 and log K_exch = −6.5 for the same two systems, respectively. Compared with earlier Na⁺-selective bulk optodes, the fabricated optical sensing microbeads reported here have agreeable selectivity patterns, reasonably fast response times, and more appropriate measuring ranges for determination of Na⁺ activity at physiological pH in undiluted blood samples.     

Screen-printed biosensors for the control of wine quality based on lactate and acetaldehyde determination

Biosensors for d-lactate and acetaldehyde were developed, based on screen-printed electrodes and NAD⁺-dependent dehydrogenases. Modification of screen-printed electrodes with the mediator Meldola Blue or with Meldola Blue-Reinecke salt resulted in sensitive, low cost and reliable NADH detectors. The biosensors were realised in two configurations, as disposable and reusable devices. Single-use sensors were obtained by simple deposition of enzyme and cofactor on the surface of mediator-modified electrodes. Chronoamperometry was used for the detection of substrates in small volumes of samples (25 μl). Immobilisation of dehydrogenases by entrapment in poly(vinyl alcohol) bearing styrylpyridinium groups (PVA-SbQ) allowed sensors to be obtained with sufficient operational stability. Amperometry in stirred solutions was the detection technique with biosensors for multiple use. The 3σ detection limits for acetaldehyde were 1 μM by amperometry and 6 μM by chronoamperometry and for d-lactate-0.03 μM and 0.05 μM for reusable and disposable biosensors respectively. The biosensors were applied in the analysis of some French and Romanian wines.     

Disposable biosensor based on cathodic electrochemiluminescence of tris(2,2-bipyridine)ruthenium(II) for uric acid determination

A new method for uric acid (UA) determination based on the quenching of the cathodic ECL of the tris(2,2-bipyridine)ruthenium(II)–uricase system is described. The biosensor is based on a double-layer design containing first tris(2,2-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) electrochemically immobilized on graphite screen-printed cells and uricase in chitosan as a second layer. The uric acid biosensing is based on the ECL quenching produced by uric acid over the cathodic ECL caused by immobilized Ru(bpy)₃²⁺ in the presence of uricase. The use of a −1.1 V pulse for 1 s with a dwelling time of 10 s makes it possible to estimate the initial enzymatic rate, which is used as the analytical signal. The Stern–Volmer type calibration function shows a dynamic range from 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M with a limit of detection of 3.1 × 10⁻⁶ M and an accuracy of 13.6% (1.0 × 10⁻⁴ M, n = 5) as relative standard deviation. Satisfactory results were obtained for urine samples, creating an affordable alternative for uric acid determination.     

Direct electrocatalytic oxidation of nitric oxide and reduction of hydrogen peroxide based on α-Fe2O3 nanoparticles-chitosan composite

α-Fe₂O₃ nanoparticles prepared using a simple solution-combusting method have been dispersed in chitosan (CH) solution to fabricate nanocomposite film on glass carbon electrode (GCE). The as-prepared α-Fe₂O₃ nanoparticles were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM). The nanocomposite film exhibits high electrocatalytic oxidation for nitric oxide (NO) and reduction for hydrogen peroxide (H₂O₂). The electrocatalytic oxidation peak is observed at +0.82 V (vs. Ag/AgCl) and controlled by diffusion process. The electrocatalytic reduction peak is observed at −0.45 V (vs. Ag/AgCl) and controlled by diffusion process. This α-Fe₂O₃-CH/GCE nanocomposite bioelectrode has response time of 5 s, linearity as 5.0 × 10⁻⁷ to 15.0 × 10⁻⁶ M of NO with a detection limit of 8.0 × 10⁻⁸ M and a sensitivity of −283.6 μA/mM. This α-Fe₂O₃-CH/GCE nanocomposite bioelectrode was further utilized in detection of H₂O₂ with a detection limit of 4.0 × 10⁻⁷ M, linearity as 1.0 × 10⁻⁶ to 44.0 × 10⁻⁶ M and with a sensitivity of 21.62 μA/mM. The shelf life of this bioelectrode is about 6 weeks under room temperature conditions.     

The first use of a Rh(III) complex as a novel ionophore for thiocyanate-selective polymeric membrane electrodes

The feasibility of a newly synthesized Rh(III) complex, Rh[(trpy)(bpy)Cl](PF₆)₂, as a novel ionophore for the preparation of anion-selective polymeric membrane electrodes was tested. The ionophore exhibited anti-Hofmeister behavior with enhanced potentiometric selectivity toward thiocyanate ion compared to other anions. The influence of some experimental parameters such as membrane composition, nature and amount of plasticizer and additive and concentration of internal solution on the potential response of the SCN⁻ sensor were investigated. The electrode exhibits a Nernstian response for SCN⁻ over a wide concentration range (1.0 × 10⁻⁵ to 1.0 × 10⁻¹ M) with a slope −58.7 ± 0.5 mV per decade and a detection limit of 4.0 × 10⁻⁶ M (0.23 ppm). It could be used in a pH range of 3.0-8.0 and has a fast response time of about 15 s. The proposed sensor was used for the determination of thiocyanate ions in real samples such as urine and saliva of smokers and nonsmokers and, as an indicator electrode, in potentiometric titrations of SCN⁻ ion.     

3D nanostructured Ni(OH)2 microspheres as an efficient immobilization matrix of Ru(bpy)3 for high-performance electrochemiluminescence sensor

The electrochemistry and electrochemiluminescence (ECL) of novel three-dimensional nanostructured Ru(bpy)₃²⁺/Ni(OH)₂ microspheres were investigated for the first time. The negatively charged porous Ni(OH)₂ microspheres composed of Ni(OH)₂ nanowires were specifically designed to interact with Ru(bpy)₃²⁺. The large surface area and porous structure of Ni(OH)₂ microspheres enhance loading of Ru(bpy)₃²⁺ and mass transport of the model analyte, tripropylamine (TPA). Excellent ECL performance of the presented sensor was achieved including good stability and wide linear range from 7.7 × 10⁻¹⁰ to 3.8 × 10⁻³ M with the detection limit of 2.6 × 10⁻¹⁰ M to TPA.     

Amperometric biosensor based on reductive H2O2 detection using pentacyanoferrate-bound polymer for creatinine determination

Pentacyanoferrate-bound poly(1-vinylimidazole) (PVI[Fe(CN)₅]) was selected as a mediator for amperometric creatinine determination based on the reductive H₂O₂ detection. Creatinine amidohydrolase (CNH), creatine amidohydrolase (CRH), sarcosine oxidase (SOD), peroxidase (POD), and PVI[Fe(CN)₅] were crosslinked with poly(ethylene glycol) diglycidyl ether (PEGDGE) on a glassy carbon (GC) electrode for a creatinine biosensor fabrication. Reduction current was monitored at −0.1 V in the presence of creatinine and O₂. It is revealed that PVI[Fe(CN)₅] is suitable as a mediator for a bioelectrocatalytic reaction of POD, since PVI[Fe(CN)₅] neither reacts with reactants nor works as an electron acceptor of SOD. The amounts of PVI[Fe(CN)₅], PEGDGE, and enzymes were optimized toward creatinine detection. Nafion as a protecting film successfully prevented the enzyme layer from interferences. The detection limit and linear range in creatinine determination were 12 μM and 12–500 μM (R² = 0.993), respectively, and the sensitivity was 11 mA cm⁻² M⁻¹, which is applicable for urine creatinine tests. The results of the creatinine determination for four urine samples measured with this proposed method were compared with Jaffe method, and a good correlation was obtained between the results.     

Mechanism study on inorganic oxidants induced inhibition of Ru(bpy)₃²+ electrochemiluminescence and its application for sensitive determination of some inorganic oxidants

Inhibited Ru(bpy)₃²⁺ electrochemiluminescence by inorganic oxidants is investigated. Results showed that a number of inorganic oxidants can quench the ECL of Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) system, and the logarithm of the decrease in ECL intensity (ΔI) was proportional to the logarithm of analyte concentrations. Based on which, a sensitive approach for detection of these inorganic oxidants was established, e.g. the log-log plots of ΔI versus the concentration of MnO₄⁻, Cr₂O₇²⁻ and Fe(CN)₆³⁻ are linear in the range of 1 × 10⁻⁷ to 3 × 10⁻⁴ M for MnO₄⁻ and Cr₂O₇²⁻, and 1 × 10⁻⁷ to 1 × 10⁻⁴ M for Fe(CN)₆³⁻, with the limit of detection (LOD) of 8.0 × 10⁻⁸ M, 2 × 10⁻⁸ M, and 1 × 10⁻⁸ M, respectively. A series of experiments such as a comparison of the inhibitory effect of different compounds on Ru(bpy)₃²⁺/TPrA ECL, ECL emission spectra, UV-Vis absorption spectra etc. were investigated in order to discover how these inorganic analytes quench the ECL of Ru(bpy)₃²⁺/TPrA system. A mechanism based on consumption of TPrA intermediate (TPrA^·) by inorganic oxidants was proposed.     

Electrogenerated chemiluminescence from CdS nanotubes and its sensing application in aqueous solution

Electrogenerated chemiluminescence (ECL) of CdS nanotubes in aqueous solution and its sensing application were studied by entrapping the CdS nanotubes in carbon paste electrode. Two ECL peaks were observed at −0.9 V (ECL-1) and −1.2 V (ECL-2), respectively, when the potential was cycled between 0 and −1.6 V. The electrochemically reduced nanocrystal species of CdS nanotubes could collide with the oxidized species in an annihilation process to produce the peak of ECL-1. The electron-transfer reaction between the reduced CdS nanocrystal species and oxidant coreactants such as S₂O₈²⁻, H₂O₂, and reduced dissolved oxygen led to the appearance of the ECL-2 peak. Based on the enhancing effect of H₂O₂ on ECL-2 intensity, a novel CdS ECL sensor was developed for H₂O₂ detection. The sensor exhibited a detection limit of 0.1 μM and a linear range from 0.5 μM to 0.01 mM. The relative standard deviations of five replicate determinations of 5 μM H₂O₂ was 2.6%. In addition, the ECL spectrum in aqueous solution also exhibited two peaks at 500 and 640 nm, respectively.     

Selective uranyl ion detection by polymeric ion-selective electrodes based on salphenH2 derivatives

The new ion-selective electrodes (ISEs) based on salphenH₂ derivatives such as N,N′-(propylenedioxy)benzenebis(salicylideneimine) L¹ and N,N′-4,5-(propylenedioxy)benzenebis(3,5-di-tert-butylsalicylideneimine) L² as cation carriers are developed for a uranyl ion. The combination of these new ionophores with tris(2-ethylhexyl)phosphate (TEHP) as a plasticizer particularly shows near Nernstian slope in the wide concentration range (1.0 × 10⁻⁶ to 1.0 × 10⁻² M) of UO₂²⁺ and is observed well in the pH range from 1.0 to 5.0 with a response time less than 20 s. Since the employed ionophores were confirmed to form well-defined stable 1:1 complexes with UO₂²⁺, the observed high selectivity for a uranyl ion over the other cations was attributed to the selective complexation as well as the lipophilic behavior of these ligands especially for L². The proposed electrodes offered practically low detection limit of 6.5 × 10⁻⁷ M and reasonably good end-points within experimental error were obtained when the sensor was used as an indicator electrode for the potentiometric titration.     

Prussian blue modified glassy carbon electrodes-study on operational stability and its application as a sucrose biosensor

Stabilisation of electrochemically deposited Prussian blue (PB) films on glassy carbon (GC) electrodes has been investigated and an enhancement in the stability of the PB films is reported if the electrodes are treated with tetrabutylammonium toluene-4-sulfonate (TTS) in the electrochemical activation step following the electrodeposition. A multi-enzyme PB based biosensor for sucrose detection was made in order to demonstrate that PB films can be coupled with an oxidase system. A tri-enzyme system, comprising glucose oxidase, mutarotase and invertase, was crosslinked with glutaraldehyde and bovine albumin serum on the PB modified glassy carbon electrode. The deposited PB operated as an electrocatalyst for electrochemical reduction of hydrogen peroxide, the final product of the enzyme reaction sequence. The electrochemical response was studied using flow injection analysis for the determination of sucrose, glucose and H₂O₂. The optimal concentrations of the immobilisation mixture was standardised as 8 U of glucose oxidase, 8 U of mutarotase, 16 U of invertase, 0.5% glutaraldehyde (0.025 μl) and 0.5% BSA (0.025 mg) in a final volume of 5 μl applied at the electrode surface (0.066 cm²). The biosensor exhibited a linear response for sucrose (4-800 μM), glucose (2-800 μM) and H₂O₂ (1-800 μM) and the detection limit was 4.5, 1.5 and 0.5 μM for sucrose, glucose and H₂O₂, respectively. The sample throughput was ca. 60 samples h⁻¹. An increase in the operational and storage stability of the sucrose biosensor was also noted when the PB modified electrodes were conditioned in phosphate buffer containing 0.05 M TTS during the preparation of the PB films.     

Modified graphitized carbon black as transducing material for reagentless H2O2 and enzyme sensors

Direct electron transfer between redox enzymes and electrodes is the basis for the third generation biosensors. We established direct electron transfer between quinohemoprotein alcohol dehydrogenase (PQQ-ADH) and modified carbon black (CBs) electrodes. Furthermore, for the first time, this phenomenon was observed for pyrroloquinoline quinone (PQQ)-dependent glucose dehydrogenase (PQQ-GDH). Reagentless enzyme biosensors suitable for the determination of ethanol, glucose and sensors for hydrogen peroxide were designed using CB electrodes and screen-printing technique. Aiming to create an optimal transducing material for biosensors, a set of CB batches was synthesized using the matrix of Plackett-Burman experimental design. Depending on the obtained surface functional groups as well as the nano-scale carbon structures in CBs batches, the maximal direct electron transfer current of glucose and ethanol biosensors can vary from 20 to 300 nA and from 30 to 6300 nA for glucose and ethanol, respectively. Using modified CB electrodes, an electrocatalytic oxidation of H₂O₂ takes place at more negative potentials (0.1-0.4 V versus Ag/AgCl). Moreover, H₂O₂ oxidation efficiency depends on the amount and morphology of fine fraction in the modified CBs.     

Fluorometric method for the determination of hydrogen peroxide and glucose with Fe3O4 as catalyst

In this paper, we utilized the instinct peroxidase-like property of Fe₃O₄ magnetic nanoparticles (MNPs) to establish a new fluorometric method for determination of hydrogen peroxide and glucose. In the presence of Fe₃O₄ MNPs as peroxidase mimetic catalyst, H₂O₂ was decomposed into radical that could quench the fluorescence of CdTe QDs more efficiently and rapidly. Then the oxidization of glucose by glucose oxidase was coupled with the fluorescence quenching of CdTe QDs by H₂O₂ producer with Fe₃O₄ MNPs catalyst, which can be used to detect glucose. Under the optimal reaction conditions, a linear correlation was established between fluorescence intensity ratio I₀/I and concentration of H₂O₂ from 1.8 × 10⁻⁷ to 9 × 10⁻⁴ mol/L with a detection limit of 1.8 × 10⁻⁸ mol/L. And a linear correlation was established between fluorescence intensity ratio I₀/I and concentration of glucose from 1.6 × 10⁻⁶ to 1.6 × 10⁻⁴ mol/L with a detection limit of 1.0 × 10⁻⁶ mol/L. The proposed method was applied to the determination of glucose in human serum samples with satisfactory results.     

Ultrasensitive fluorometric determination of hydrogen peroxide and glucose by using multiferroic BiFeO3 nanoparticles as a catalyst

BiFeO₃ magnetic nanoparticles (BFO MNPs) are used as a catalyst to develop an ultrasensitive method for the determination of H₂O₂. It is found that BFO MNPs can catalyze the decomposition of H₂O₂ to produce OH radicals, which in turn oxidize the weakly fluorescent benzoic acid to a strongly fluorescent hydroxylated product with a maximum emission at 405 nm. This makes it possible to sensitively quantify traces of H₂O₂. Under optimized conditions, the fluorescence intensity is observed to be well linearly correlated with H₂O₂ concentration from 2.0 × 10⁻⁸ to 2.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 4.5 × 10⁻⁹ mol L⁻¹ (S/N = 3). In addition, a selective method for glucose determination is developed by using both glucose oxidase and BFO MNPs, which has a linear range for glucose concentration from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. These new methods have been successfully applied for the determination of H₂O₂ in rainwater and glucose in human serum samples.