HG-ICP-MS同时测定生物样品中痕量As,Se,Hg

以HNO3为介质,采用自行研制的二级气液分离器代替易消耗的膜分离器,在优化的实验条件下,采用HG-ICP-MS实现了As,Se,Hg的同时测定,分别获得了0.022,0.016,0.009 ngmL的检出限。实验研究了二级气液分离器中的气液分离行为、样品酸度、NaBH4质量浓度和引入方式等因素对测定灵敏度和精密度的影响。实验的结果表明,HG-ICP-MS同时测定As,Se,Hg的主要干扰来自于Fe,cu等过渡金属离子,样品溶液中抗坏血酸-硫脲的加入可以掩蔽这些离子的干扰。利用所建立的方法测定了人发、灌木叶和大米粉标样中痕量的As,Se,Hg,结果与标准参考值相符。     

Determination of trace lead by hydride generation-inductively coupled plasma-mass spectrometry

A newly developed hydride generation-inductively coupled plasma-mass spectrometry (HG-ICP-MS) system was employed to determine trace amounts of lead in geological and biological samples. Laboratory-made single-stage and double-stage gas-liquid separators (GLSs) were investigated in order to replace the consumable membrane-GLS. Possible reasons were given why double-stage GLSs were superior over the single-stage ones according to the factors such as GLS volume and configuration, carrier gas inlet mode and flow rate. Interferences in liquid and vapor phase from concomitant ions and their products were investigated employing different flow mani-folds. Memory effects contributed to the blank values, but could be reduced employing a special wash protocol. Internal and external standardization were combined to improve the accuracy of the method, with bismuth as the internal standard according to its similarity with lead in the HG-ICP-MS system. Compared with ICP-MS and hydride generation-atomic fluorescence spectrometry (HG-AFS) methods, the system performance of HG-ICP-MS was characterized with improved detection limit to 0.002 ng/ml and acceptable short- and long-term stabilities. The linear dynamic range of this method was up to 50 ng/ml lead. Three Chinese national certified reference materials: poplar leaves, human hair and copper ore, were analyzed for method validation, and the results agreed well with the certified values. At last, the method was also employed to determine wide range of lead concentrations in lightweight limestone and nervous tissue samples from infants of albino rats with recoveries between 95 and 105% (n=10).     

Ultra-trace determination of iodine in sediments and biological material using UV photochemical generation-inductively coupled plasma mass spectrometry

Several sample preparation techniques have been evaluated for the determination of iodine using UV-photochemical generation-quadrupole inductively coupled plasma mass spectrometry. Thermal decomposition of samples at 1000 °C followed by capture of the liberated iodine in dilute acetic acid permitted subsequent UV-photochemical generation of a volatile iodine species that serves to enhance sensitivity 25-fold over conventional solution nebulization, delivering reagent blank detection limits of 8.75 pg g^{–1 127}I and 0.075 pg g^–1 129I for solid samples (400 mg test mass). The methodology was validated through determination of total iodine in several Standard Reference Materials, including NIST 1572 Citrus leaves, NIST 1549 Non-fat milk powder, NIST 1566a Oyster tissue and NIST 2709 San Joaquin Soil. Liberation of iodine from samples and its collection as well as photochemical generation were quantitative, permitting calibration to be achieved using standards prepared in dilute acetic acid.     

Determination of arsenic,selenium and mercury in an estuarine sediment standard reference material using flow injection and atomic absorption spectrometry

A flow-injection analysis atomic absorption spectrometric (FIA-AAS) method was developed for the determination of trace amounts of arsenic, selenium and mercury in a proposed estuarine sediment standard reference material (SRM 1646a). The samples were prepared in two manners: a) A wet digestion procedure with HNO₃, H₂SO₄, and HClO₄ using a reflux column and b) A microwave-oven digestion procedure utilizing HNO₃, H₂SO₄, and HCl for As and Se, and HNO₃ for Hg. Microwave-oven digestion provides results comparable to those found by reflux column digestion and reduces the sample preparation time by a factor of 10. The proposed method employing the microwave-oven digestion procedure coupled with FIA-AAS for As and Se, and FIA-CVAAS for Hg, has detection limits of 0.15 ng As/ml, O.17 ng Se/ml and 0.15 ng Hg/ml.On leave from the Defense Metallurgical Research Laboratory, Hyderabad, India     

Simultaneous determination of arsenic, selenium, tin and mercury by non-dispersive atomic fluorescence spectrometry

A procedure is described for simultaneous determination of arsenic, selenium, tin and mercury in aqueous solution by non-dispersive atomic-fluorescence spectrometry. Radiofrequency-excited EDLs, 100% modulated in the kHz region, were used for atom excitation. Sodium tetrahydroborate was used as reductant and a hydrogen-argon miniflame as atomizer. In the optimized procedure, which uses 1 ml of sample, the limits of detection (three times the standard deviation of the blank) were 0.04, 0.08, 0.1 and 0.1 ng ml for arsenic, selenium, tin and mercury respectively. The linear dynamic range was greater than three decades for all analytes and the precision was better than 7% (typically 3%) for concentrations 1 ng ml . Results for mutual interference effects are reported. Copper, nickel, lead and cobalt interfered only with selenium (5 ng ml ), when present in at least 200-fold weight ratio to it. Using 5 ml of sample improved the limits of detection for selenium and arsenic (0.01 and 0.02 ng ml respectively), but at the expense of greater interference. Recovery from spiked natural water samples was better than 95% at the ng ml level, except for selenium in sea-water, when the recovery was only 85%. Determination of the four elements, including standard-addition and background measurements, requires about 10 min.     

On-line separation and preconcentration of inorganic arsenic and selenium species in natural water samples with CTAB-modified alkyl silica microcolumn and determination by inductively coupled plasma-optical emission spectrometry

A new, simple, and selective method has been presented for the separation and preconcentration of inorganic arsenic (As(III)/As(V)) and selenium (Se(IV)/Se(VI)) species by a microcolumn on-line coupled with inductively coupled plasma-optical emission spectrometry (ICP-OES). Trace amounts of As(V) and Se(VI) species were separated and preconcentrated from total As and Se at desired pH values by a conical microcolumn packed with cetyltrimethylammonium bromide (CTAB)-modified alkyl silica sorbent in the absence of chelating reagent. The species adsorbed by CTAB-modified alkyl silica sorbent were quantitatively desorbed with 0.10 ml of 1.0 mol l⁻¹ HNO₃. Total inorganic arsenic and selenium were similarly extracted after oxidation of As(III) and Se(IV) to As(V) and Se(VI) with KMnO₄ (50.0 μmol l⁻¹). The assay of As(III) and Se(IV) were based on subtracting As(V) and Se(VI) from total As and total Se, respectively. All parameters affecting the separation/preconcentration of As(V) and Se(VI) including pH, sample flow rate and volume, eluent solution and volume have been studied. With a sample volume of 3.0 ml, the sample throughput was 24 h⁻¹ and the enrichment factors for As(V) and Se(VI) were 26.7 and 27.6, respectively. The limits of detection (LODs) were 0.15 μg l⁻¹ for As(V) and 0.10 μg l⁻¹ for Se(VI). The relative standard deviations (RSDs) for nine replicate determinations at 5.0 μg l⁻¹ level of As(V) and Se(VI) were 4.0% and 3.6%, respectively. The calibration graphs of the method for As(V) and Se(VI) were linear in the range of 0.5–1000.0 μg l⁻¹ with a correlation coefficient of 0.9936 and 0.9992, respectively. The developed method was successfully applied to the speciation analysis of inorganic arsenic and selenium in natural water samples with satisfactory results.     

化学蒸气发生-四通道原子荧光光谱法同时测定水样中的痕量砷、锑、硒和汞

应用自行设计的化学蒸气发生-四通道无色散原子荧光光谱仪,建立了同时测定水样中As、Sb、Se、Hg的新方法.在实验中优化了四元素同时化学蒸气发生条件和测定的最佳工作参数.在样品预处理阶段用HCl将Se6+还原为Se4+,然后用质量浓度5 g/L硫脲将As5+和Sb5+还原为As3+和Sb3+.在最佳条件下,方法对As、Sb、Se、Hg的检出限分别为0.05、0.03、0.05、0.01 ng/mL(3d);RSD分别为0.42%、0.74%、0.97%、1.0%(对5 ng/mL As、Sb、Se和0.5ng/mL Hg混合标准,n=7).用所建立的方法对不同类型水样中的As、Sb、Se、Hg进行了同时测定,测定结果与用标准方法测定所得结果之间无明显差异,各元素的加标回收率在93%～105%.     

Simultaneous determination of arsenic species and chromium(VI) by high-performance liquid chromatography-inductively coupled plasma-mass spectrometry

The simultaneous determination of As(III), As(V), monomethylarsenic acid (MMA), dimethylarsinic acid (DMA) and Cr(VI) in fresh water has been carried out by coupling an anion-exchange column to an inductively coupled plasma-mass spectrometer. Optimisation of chromatographic conditions led to baseline separation of signals from the five species in approximately 9 min using gradient elution. Detection limits were 0.02-0.05 microg As l(-1) and 5.5 microg Cr l(-1). Repeatability was 2-3% for arsenic species and higher, i.e., 8%, for Cr(VI) due to the higher background for this species. Arsenic species and hexavalent chromium stability in surface water samples was evaluated, and storage conditions were set to 1 day at 4 degrees C in polyethylene flasks (without acidification) in order to avoid As(III)-As(V) conversions. The method was applied to the analysis of surface water.     

Dissolved inorganic carbon effect in the determination of arsenic and chromium in mineral waters by inductively coupled plasma-mass spectrometry

The analysis of some Italian mineral waters by ICP-MS has revealed errors in the determination of As and Cr in natural effervescent or carbonated waters due to the presence of dissolved inorganic carbon (DIC). This leads to overestimate As and Cr in 1% (v/v) HNO₃ acidified samples, analysed within 1-2 h after the acidification. The overestimation of As concentration is caused by matrix interferences producing a signal enhancement due to the presence of dissolved inorganic carbon. This effect is analogous to that observed in the presence of organic carbon and occurs at millimolar DIC levels. The overestimation of Cr concentration is due to the ⁴⁰Ar¹²C⁺ species interfering with ⁵²Cr⁺ despite the use of the octopole reaction system. The optimization of the He flow in the collision cell can solve the latter problem, but the required increase in the flow rate decreases the sensitivity of the ICP-MS technique. The observed effects in CO₂ rich mineral waters and artificial NaHCO₃ solutions suggest that 5-10 mM DIC levels may affect the determination of As and Cr concentration in thermal waters, rivers, lakes and groundwaters.     

Complementary chromatography separation combined with hydride generation-inductively coupled plasma mass spectrometry for arsenic speciation in human urine

This study aimed to establish complementary high performance liquid chromatography (HPLC) methods including three modes of separation: ion pairing, cation exchange, and anion exchange chromatography, with detection by inductively coupled plasma mass spectrometry (ICPMS). The ion pairing mode enabled the separation of inorganic arsenate (As(V)), monomethylarsonic acid (MMA(V)), and dimethylarsinic acid (DMA(V)). However, the ion pair mode was unable to differentiate inorganic arsenite (As(III)) from arsenobetaine (AsB); instead, cation exchange chromatography was used to isolate and quantify AsB. Anion exchange chromatography was able to speciate all of the aforementioned arsenic species. Potential inaccurate quantification problem with urine sample containing elevated concentration of AsB, which eluted immediately after As(III) in anion exchange or ion pairing mode, was overcame by introducing a post-column hydride generation (HG) derivatization step. Incorporating HG between HPLC and ICPMS improved sensitivity and specificity by differentiating AsB from hydride-forming arsenic species. This paper emphasizes the usefulness of complementary chromatographic separations in combination with HG-ICPMS to quantitatively determine concentrations of As(III), DMA(V), MMA(V), As(V), and AsB in the sub-microgram per liter range in human urine.     

Contribution to vapor generation-inductively coupled plasma spectrometric techniques for determination of sulfide in water samples

Vapor generation-inductively coupled plasma-optical emission spectrometry was used for the determination of sulfide in water samples preserved by the addition of a zinc acetate and sodium hydroxide solution. Hydrogen sulfide and acid-volatile sulfides were transformed, by acidification, to a gaseous phase in a vapor generator and subsequently detected by inductively coupled plasma optical emission spectrometry. Compounds interfering with iodometric titration and spectrophotometric determination were examined as potential chemical interferents. The proposed method provides results comparable to iodometric titration in the tested concentration range 0.06-22.0 mg L⁻¹. Limit of detection for the determination of hydrogen sulfide by this method is 0.03 mg L⁻¹.     

Multivariate optimization of mercury determination by flow injection-cold vapor generation-inductively coupled plasma optical emission spectrometry

In this work a procedure for mercury determination by Flow Injection-Cold Vapor Generation-Inductively Coupled Plasma Optical Emission Spectrometry (FI-CVG-ICP OES) has been developed. The system uses a small homemade glass separator constructed to drive the Hg vapor to the plasma. An evolutionary operation factorial design was used to evaluate the optimal experimental conditions for mercury vapor generation, aiming at the low consumption of reagents, the improvement of the analytical signal and consequently greater sensitivity. The procedure allowed the determination of mercury and showed excellent linearity for the concentration range from 0.50 μg L(-1) to 100.0 μg L(-1), with Limits of Detection (LOD) and Quantification (LOQ) of 0.11 μg L(-1) and 0.36 μg L(-1), respectively, and a sampling rate of 36 analyses per hour. The optimized procedure showed good accuracy and precision, and the method was validated by the analysis of two certified reference materials: Buffalo River Sediment (NIST 2704) and human hair (IAEA 085). A good agreement with the certified values was achieved, with recovery values of 99% and 98% and relative standard deviation close to 2%.     

液相色谱-电感耦合等离子体质谱法测定稻米中的5种砷形态

建立了稻米中砷酸根[As（Ⅴ）]、亚砷酸根[As（Ⅲ）]、砷甜菜碱（AsB）、一甲基砷（MMA）和二甲基砷（DMA）的液相色谱-电感耦合等离子体质谱（LC-ICP-MS）检测方法。以0.3 mol/L硝酸水溶液为提取试剂,样品在石墨消解仪中于95 ℃消解1.5 h,上清液供LC-ICP-MS分析。5种砷形态采用Dionex IonPac AS19阴离子交换柱（250 mm×4 mm）分离,经ICP-MS检测。比较了4种提取液对稻米中5种砷形态的提取效率,并对提取溶剂的浓度、提取温度和提取时间等条件进行了优化。通过加标回收试验结合测定标准物质考察了方法准确度及精密度,在2个加标水平上各形态的回收率为89.6%~99.5%,RSD（n=5）不大于3.6%,大米标准物质中各形态之和的测定结果与其标准值吻合,5种砷形态的线性范围AsB和DMA为0.05~200 μg/L,As（Ⅲ）和MMA为0.10~400 μg/L,As（V）为0.15~600 μg/L,方法检出限为0.15~0.45 μg/kg。结果表明,本方法简单、灵敏、耐用,可用于稻米中5种砷形态的准确定量和风险评估。     

电感耦合等离子体发射光谱法测定粗二氧化碲中 铜、铅、锑、铋、砷和硒

粗二氧化碲作为碲精炼或碲化工产品生产的重要原料,其中共存元素铜、铅、砷、锑、铋、硒含量的准确测定对于生产过程质量控制和贸易结算具有重要意义,但目前没有粗二氧化碲中铜、铅、砷、锑、铋、硒含量检测的标准分析方法。采用王水和饱和氟化氢铵分解试样,在王水和酒石酸介质中,选用Cu 327.393 nm、Pb 220.353 nm、Sb 217.582 nm、Bi 223.061 nm、As 193.696 nm、Se 196.026 nm为分析谱线,采用电感耦合等离子体发射光谱(ICP-AES)法测定粗二氧化碲中铜、铅、锑、铋、砷和硒含量。各元素校准曲线的相关系数均大于0.999;铜、铅、锑、铋、砷和硒的检出限分别为0.0004%、0.0005%、0.0006%、0.0007%、0.0004%和0.0007%,定量检出限分别为0.0012%、0.0016%、0.0020%、0.0025%、0.0013%和0.0025%。按照实验方法测定5个粗二氧化碲样品中铜、铅、锑、铋、砷和硒,测定结果的相对标准偏差(RSD,n=7)为0.79%~4.8%,加标回收率为96.0%~103%。方法简单,精密度和准确度较高,可用于测定粗二氧化碲中铜、铅、砷、锑、铋、硒含量。     

Simultaneous determination of selenium and arsenic contents in different extracts of Radix Astragali by enhancement effect of ethanol in hydride generation-inductively coupled plasma-atomic emission spectrometry

A new method was developed for simultaneous determination of trace arsenic and selenium in different extracts of Radix Astragali by enhancement effect of ethanol in hydride generation-inductively coupled plasma-atomic emission spectrometry (HG-ICP-AES) with a microwave digestion system. The effects of the concentration of the hydride generating reagent (NaBH₄), ethanol concentration, different extraction methods and pre-reducing reagents on selenium and arsenic emission intensity were discussed and optimized. The contents of selenium and arsenic in different extracts (polysaccharide, amino acid, astragaloside, and water decoction,) in Radix Astragali were analyzed. The proposed method was validated by the use of two plant reference samples {poplar leaf (GBW07604) and tea (GBW07605)}. The detection limits (3σ) were 7.0 ng L^− 1 and 2.0 ng L^− 1 for Se(IV) and As(III) and relative standard deviations (RSD) were 1.8% and 2.3%, respectively. The determination of Selenium and Arsenic contents in different extracts of Radix Astragali would provide useful information for the quality control of Radix Astragali.     

Simultaneous determination of arsenic, selenium and mercury in foodstuffs by chemical vapour generation inductively coupled plasma optical emission spectroscopy

A procedure for the simultaneous determination of arsenic, selenium and mercury in foodstuffs has been developed. After a two-step microwave-assisted wet digestion in closed vessels, using concentrated nitric acid and hydrogen peroxide, the solution was analysed by inductively coupled plasma multichannel-based emission spectrometry using chemical vapour generation as the sample introduction system. All steps of the procedure, such as solid sample dissolution, pre-reduction to the suitable oxidation state, vapor generation, transport and atomization have been designed and optimised taking into account the concomitant presence of all the analytes considered. Temporal variation of analytical signals as well as interfering effects due to transition elements were also studied. Under the optimised operating conditions, the achieved detection limits for the simultaneous determination of arsenic, selenium and mercury in foodstuffs were 0.006, 0.023 and 0.018 microg g(-1), respectively, allowing their determination in real samples. Precision of the analytical procedure was 6.8% for arsenic, 5.2% for selenium and 7.7% for mercury (n=7). The accuracy and reliability of the method was verified by the analysis of both standard reference materials (rice flour and spinach leaves) and real samples (natural and Se-enriched rice).     

Simultaneous determination of trace arsenic, antimony, bismuth and selenium in biological samples by hydride generation-four-channel atomic fluorescence spectrometry

A new and sample technique for the simultaneous determination of trace arsenic, antimony, bismuth and selenium in biologic samples by hydride generation-four-channel nondispersive atomic fluorescence spectrometry was development. The conditions of instrumentation and hydride generation of arsenic, antimony, bismuth and selenium were optimized. For reducing hexavalent Se to the tetravalent state was to heat the sample with 6 mol l⁻¹ HCl, and then pre-reducing pentavalent As and Sb to the trivalent state was achieved by the addition of 0.05 mol l⁻¹ thiourea. The interferences of coexisting ions were evaluated. Under optimal conditions, the detection limits for As, Sb, Bi and Se were determined to be 0.03, 0.04, 0.04 and 0.03 ng ml⁻¹, respectively. The precision for seven replicate determinations at the 5 ng ml⁻¹ of As, Sb, Bi and Se were 0.9, 1.2, 1.3 and 1.5% (R.S.D.), respectively. The proposed method was successfully applied to the simultaneous determination of As, Sb, Bi and Se in a series of Chinese certified biological reference materials using simple aqueous standard calibration technique, the results obtained are in good agreement with the certified values.     

Simultaneous determination of arsenic, antimony and selenium by gas-phase diode array molecular absorption spectrometry, after preconcentration in a cryogenic trap

This paper describes a method for the simultaneous determination of As(III), Sb(III) and Se(IV) by combining hydride generation and gas phase molecular absorption spectrometry. A system for continuous hydride generation has been designed and developed, based on the use of a double process of gas-liquid separation, and optimal compromise operation conditions for the three compounds have been found. After generation, the hydrides are collected in a liquid nitrogen cryogenic trap, and then evaporated and driven to the flow cell of a diode array spectrophotometer, in which the transient signals over the 190–250 nm wavelength interval are measured. Under the recommended conditions (sample flow: 35 ml min⁻¹, 0.5 M HCl; reductor flow: 4 ml min⁻¹ of 4% NaBH₄, solution) linear response ranges above 50 μg 1⁻¹ for As(III), 30 μg 1⁻¹ for Sb(III) and 200 μg 1⁻¹ for Se(IV) are obtained with detection limits of 22 μg 1⁻¹, 15 μg 1⁻¹ and 65 μg 1⁻¹, respectively. Multiwavelength linear regression equations were used for the simultaneous determination of the three elements in different synthetic samples, with good precision and accuracy and to study simultaneously the interference from different chemical species for the three compounds. Results were similar to those obtained by other techniques using hydride generation.     

电感耦合等离子体质谱法检测氧化镓中杂质元素

建立了电感耦合等离子体质谱法(ICP-MS)测定氧化镓中杂质元素的检测方法,采用微波消解技术溶样,以5 ng/mL Rh为内标补偿校正镓基体的抑制效应,采用碰撞室技术(CCT)消除多元素分子离子的干扰.方法的检出限为0.10～1.0 ng/mL,加标回收率在85%～110%之间,RSD为0.6%～7.1%.该方法能满足99.95%～99.995%氧化镓中杂质元素的分析要求.     

氧化镁烧结-电感耦合等离子质谱法测定冰铜中的铼

本文建立了一种利用电感耦合等离子体质谱法（ICP-MS）测定冰铜中铼的方法。样品经氧化镁烧结,热水浸取法处理,溶液经732强酸型阳离子交换树脂处理交换去除干扰离子,实现了ICP-MS直接测定冰铜中的铼。实验结果表明,在最佳试验条件下,方法的检出限可低至0.010mg/t,加标回收率为92.00%~104.00%,测定结果的相对标准偏差（RSD,n=7）小于5%,测定结果令人满意。由此可见,该方法精密度高,准确度高,可用于冰铜中铼的测定。