Simultaneous determination of copper and lead in seawater using optimised thin-mercury film electrodes in situ plated in thiocyanate media

In the present work the anodic stripping voltammetric (ASV) methodology using a thin mercury film electrode in situ plated in thiocyanate media was re-assessed in order to allow the simultaneous determination of copper and lead in seawater. Under previously suggested conditions [6], i.e. using a concentration of thiocyanate of 5 mM, the ASV peaks of copper and lead overlapped due to the formation of a stable copper(I)-thiocyanate species, limiting the analytical determinations. Therefore, the best value for the thiocyanate concentration was re-evaluated: for 0.05 mM a trade-off between good resolution of the copper and lead peaks and high reproducibility of the mercury film formation/removing processes was achieved. In this media, the ASV peaks for Pb and Cu occurred, separated by 140 mV. Also, the in situ thin mercury film electrode was produced and removed with good repeatability, which was confirmed by the relative standard deviation values for the ASV determinations: 0.5% for Pb and 2.0% for Cu (10 replicate determinations in a solution with metal concentrations 1.5×10⁻⁸ M for lead and 2.2×10⁻⁸ M for copper). The optimised methodology was successfully applied to the determination of copper in the presence of lead, in certified seawater (NASS-5).     

Ion-exchange and permselectivity properties of poly(sodium 4-styrenesulfonate) coatings on glassy carbon: application in the modification of mercury film electrodes for the direct voltammetric analysis of trace metals in estuarine waters

The present work describes the optimisation and characterization of poly(sodium 4-styrenesulfonate)-coated thin mercury film electrodes (PSS-TMFE) for the direct analysis of trace metals in estuarine waters by square-wave anodic stripping voltammetry (SW-ASV). The morphology, thickness and ion exchange ability of the poly(sodium 4-styrenesulfonate) coatings onto glassy carbon were evaluated and these features particularly favoured the incorporation of cationic species, such as dopamine or lead cation. For the case of the heavy metal cations, a simple, sensitive and very reproducible methodology for their SW-ASV analysis could be developed. In fact, with the PSS-TMFE, a significant increase in the sensitivity of the ASV determination of lead was obtained compared both to the uncoated TMFE (ca. 82%) as well as to Nafion-coated electrodes of similar thickness (ca. 43-49%). Furthermore, the permselectivity of the poly(sodium 4-styrenesulfonate) coatings, based both on electrostatic interaction and molecular size, leads to an improved anti-fouling ability against surfactant species. The analytical usefulness of the poly(sodium 4-styrenesulfonate)-coated thin mercury film electrodes is demonstrated by application to the direct ASV determination of trace heavy metals at the low nanomolar level, in estuarine waters with moderate contents of dissolved organic matter, where the uncoated TMFE failed due to fouling.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.     

Detection of lead ions in picomolar concentration range using underpotential deposition on silver nanoparticles-deposited glassy carbon electrodes

The efficacy of silver-deposited glassy carbon electrode for the determination of lead ions at the sub-nanomolar concentration ranges is investigated. The silver nanoparticles are electrodeposited on glassy carbon electrode using chronoamperometry and the electrode surface is characterized using SEM. Lead ions are detected in the region of underpotential deposition. The analysis is performed in square wave mode in the stripping voltammetry without the removal of oxygen. The detection limit of 10 pM has been obtained with a constant potential of −0.7 V during the electrodeposition step for a period of 50 s. The interference of surfactants in the detection of lead ions is also studied.     

Effect of the modification of mercuric oxide on the properties of mercury films at HgO-modified carbon paste electrodes

The influence of modifications of the mercuric oxide on the voltammetric properties of mercury film carbon paste electrodes was studied. The mercury film was formed electrochemically from the bulk red or yellow mercuric oxide-modified carbon paste electrodes. Differential pulse anodic stripping voltammetry and optical microscopy in polarised light were used to characterise the properties of the mercury films. The results were compared with those obtained using the conventional preparation of mercury-plated carbon paste electrodes when the mercury film is deposited on the surface of the electrode by reduction of Hg(II) ions in solution utilising a sufficient negative potential. It was shown that the mercury film formed from the yellow modification of the mercuric oxide provides better voltammetric characteristics than the red one owing to the high distribution of its small particles, i.e. the mercury droplets after electrochemical treatment. Such a mercury film has similar properties to those of a mercury film generated from solution. Received: 06 December 1999 / Accepted: 16 March 2000     

Comparison of constant-current stripping chronopotentiometry and anodic stripping voltammetry in metal speciation studies using mercury drop and film electrodes

Capabilities for heavy metal speciation of anodic stripping voltammetry (ASV) and constant-current stripping chronopotentiometry (SCP) in both mercury drop (HMDE) and mercury film rotating disk (MFE-RDE) electrodes are compared. For this purpose, the Cd(II)–glycine and Cd(II)–polymethacrylate (PMA) systems are used as models of simple labile and macromolecular labile complexes adsorbing onto the electrode, respectively. The results suggest that SCP could be a valuable alternative to the more widespread ASV in this kind of study. Concerning the electrode, the MFE-RDE is less user-friendly than the HMDE, but presents a better definition of both the hydrodynamic conditions during the deposition step and the stripping regime during the oxidation. An important interference in SCP is the dissolved oxygen, which can be minimised by combining relatively large oxidation currents and low stirring rates. Moreover, for Cd–PMA, double peaks have been observed in both ASV and SCP, which seems to be due to the lack of enough ligand excess to complex the metal ions released by the amalgam oxidation. Anyway, this problem can be minimised by optimising the rotation rate of the electrode and ensuring enough ligand excess.     

The use of Nafion-coated thin mercury film electrodes for the determination of the dissolved copper speciation in estuarine water

Differential pulse anodic stripping voltammetry (DPASV) using a Nafion-coated thin mercury film electrode (NCTMFE) was implemented to determine the dissolved copper speciation in saline estuarine waters containing high concentrations of dissolved organic matter (DOM). The study used model ligands and estuarine water from San Francisco Bay, California, USA to demonstrate that the NCTMFE is more effective at distinguishing between electrochemically inert and labile copper species when compared to the conventional thin mercury film electrode (TMFE). Copper titration results verify that the NCTMFE better deals with high concentrations of DOM by creating a size-exclusion barrier that prevents DOM from interacting with the mercury electrode when performing copper speciation measurements. Pseudovoltammograms were used to illustrate that copper complexes found in natural waters were more apt to be electrochemically inert at the NCTMFE relative to the TMFE when subjected to high negative overpotentials. Copper speciation results using the NCTMFE from samples collected in San Francisco Bay estimated that >99.9% of all copper was bound to strong copper-binding ligands. These L₁-class ligands exceeded the concentration of total dissolved copper in all samples tested and control the equilibrium of ambient [Cu²⁺] in the San Francisco Bay estuary.     

Quantitative determination of zinc in milkvetch by anodic stripping voltammetry with bismuth film electrodes

Bismuth film electrode (BiFE) was shown to be an attractive alternative to common mercury film electrode (MFE) for anodic stripping voltammetric measurements. In this study, bismuth film, that was in situ deposited onto glassy carbon electrode, was used to detect zinc content of milkvetch, used in traditional Chinese medicine. Variables affecting the response have been evaluated and optimized. Experimental results showed a high response, with a good linearity (between 0.5 × 10⁻⁶ mol L⁻¹ and 3 × 10⁻⁶ mol L⁻¹) a good precision (R.S.D. = 3.58%) and a low detection limit (9.6 × 10⁻⁹ mol L⁻¹ with a 120 s anodic). The anodic stripping performance makes the bismuth film electrode very desirable for measurements of trace nutritive element zinc in milkvetch and should impart possible restrictions on the use of mercury electrode.     

The Use of the Bismuth Film Electrode for the Anodic Stripping Voltammetric Determination of Tin

Bismuth coated glassy carbon electrodes have been applied to the square‐wave anodic stripping voltammetry (SWASV) of trace concentrations of tin. Optimization of Bismuth Film Electrode (BFE) performance was conducted after initial comparison with the more traditional mercury electrode. Simultaneous deposition of tin and bismuth at ?1.3 V for 2 minutes in a supporting electrolyte of 2.5 M sodium bromide utilizing a square‐wave stripping step, allowed analysis of tin at the μg L^?1 level. Parameters, such as deposition potential and time, bismuth concentration, square‐waveform settings including amplitude, step height and frequency were studied and optimized. The dependence of stripping current on deposition time indicates that using longer deposition time should facilitate sub μg L^?1 analysis. Tin was analyzed simultaneously with cadmium and either indium or thallium; Where as lead and copper were not resolved from the stripping peaks of tin and bismuth respectively. Finally, the method was applied to the analysis of tin in fruit juice.     

Functioning of antimony film electrode in acid media under cyclic and anodic stripping voltammetry conditions

New insights into the functioning, i.e. electrochemical behaviour and analytical performance, of in situ prepared antimony film electrodes (SbFEs) under square-wave anodic stripping (SW-ASV) and cyclic (CV) voltammetry conditions are presented by studying several key operational parameters using Pb(II), Cd(II) and Zn(II) as model analyte ions. Five different carbon- and metal-based substrate transducer electrodes revealed a clear advantage of the former ones while the concentration of the precursor Sb(III) ion exhibited a distinct influence on the ASV functioning of the SbFE. Among six acids examined as potential supporting electrolytes the HNO₃ was demonstrated to yield nearly identical results in conducting ASV experiments with SbFE as so far almost exclusively used HCl. This is extremely important as HNO₃ is commonly employed acidifying agent in trace metal analysis, especially in elemental mass spectrometry measurements. By carrying out a systematic CV and ASV investigation using a medium exchange protocol, we confirmed the formation of poorly soluble oxidized Sb species at the substrate electrode surface at the end of each stripping step, i.e. at the potentials beyond the anodic dissolution of the antimony film. Hence, the significance of the cleaning and initializing the surface of a substrate electrode after accomplishing a stripping step was thoroughly studied in order to find conditions for a complete removal of the adhered Sb-oxides and thus to assure a memory-free functioning of the in situ prepared SbFE. Finally, the practical analytical application of the proposed ASV method was successfully tested and evaluated by measuring the three metal analytes in ground (tap) and surface (river) water samples acidified with HNO₃. Our results approved the appropriateness of the SbFE and the proposed method for measuring low μg L⁻¹ levels of some toxic metals, particularly taking into account the possibility of on-field testing and the use of low cost instrumentation.     

Effects of Electroplating Variables on the Voltammetric Properties of Bismuth Deposits Plated Potentiostatically

An attempt is made to describe the electrochemical properties of bismuth films, plated in‐situ on glassy carbon in acetic buffer, over a broad range of deposition potentials. It is shown that accumulation during anodic stripping voltammetric determination of lead and zinc at the bismuth film electrode depends to a large extent on the electrolyte composition and the plating parameters. The influence of the plating potential on Pb deposition is moderate, but it could not be disregarded during Zn quantification. The sources of electrode poisoning effects are discussed in detail. Voltammetric studies are complemented by AFM microscopic observations.     

Poly(ester sulphonic acid) coated mercury thin film electrodes: characterization and application in batch injection analysis stripping voltammetry of heavy metal ions

Mercury-thin film electrodes coated with a thin film of poly(ester sulphonic acid) (PESA) have been investigated for application in the analysis of trace heavy metals by square wave anodic stripping voltammetry using the batch injection analysis (BIA) technique. Different polymer dispersion concentrations in water/acetone mixed solvent are investigated and are characterised by electrochemical impedance measurements on glassy carbon and on mercury film electrodes. The influence of electrolyte anion, acetate or nitrate, on polymer film properties is demonstrated, acetate buffer being shown to be preferable for stripping voltammetry applications. Although stripping currents are between 30 and 70% less at the coated than at bare mercury thin film electrodes, the influence of model surfactants on stripping response is shown to be very small. The effect of the composition of the modifier film dispersion on calibration plots is shown; however, detection limits of around 5 nM are found for all modified electrodes tested. This coated electrode is an alternative to Nafion-coated mercury thin film electrodes for the analysis of trace metals in complex matrices, particularly useful when there is a high concentration of non-ionic detergents.     

The determination of copper at thin film electrodes by constant current stripping potentiometry

A comparison of the determination of copper by constant current stripping potentiometry (CCSP) at mercury and gold films has been carried out. The preferred solution conditions for the mercury film study were determined to be 0.1M ammonium acetate at pH 4.5 and 0.1M HCl for the gold film study. The influence of chloride on the stripping signal was investigated and it was found that for the mercury film conditions, well-formed stripping signals could be obtained up to a chloride concentration of 0.5 M which permitted the ready determination of copper in seawater. With the gold film, high chloride concentrations affected both the film stability and the glassy carbon surface and repeatable results were difficult to obtain. The optimized CCSP methods were applied to various aqueous samples including tap water, seawater, TCLP (acetic acid) extracts as well as TCLP extracts using groundwater and ocean water. Based on the results obtained for these various matrices, it was concluded that there are several advantages favoring the mercury film. The interference from organic components in the sample matrix on the general applicability of CCSP for the determination of copper at either a mercury or gold film is discussed.     

Mixed polyelectrolyte coatings on glassy carbon electrodes: Ion-exchange, permselectivity properties and analytical application of poly-l-lysine-poly(sodium 4-styrenesulfonate)-coated mercury film electrodes for the detection of trace metals

The present work describes the preparation, optimization and characterization of mixed polyelectrolyte coatings of poly-l-lysine (PLL) and poly(sodium 4-styrenesulfonate) (PSS) for the modification of thin mercury film electrodes (MFEs). The novel-modified electrodes were applied in the direct analysis of trace metals in estuarine waters by square-wave anodic stripping voltammetry (SWASV). The effects of the coating morphology and thickness and also of the monomeric molar ratio PLL/PSS on the cation-exchange ability of the PLL–PSS polyelectrolyte coatings onto glassy carbon (GC) were evaluated using target cationic species such as dopamine (DA) or lead cation. Further, the semi-permeability of the PLL–PSS-coated electrodes based both on electrostatic interactions and on molecular size leads to an improved anti-fouling ability against several tensioactive species. The analytical usefulness of the PLL–PSS-mixed polyelectrolyte coatings on thin mercury film electrodes is demonstrated via SWASV measurements of trace metals (lead, copper and cadmium at the low nanomolar level; accumulation time of 180 s) in estuarine waters containing moderate levels of dissolved organic matter, resulting in a fast and direct methodology requiring no sample pretreatment.     

Electrochemical behaviour of gold, silver, platinum and palladium on the glassy carbon electrode modified by chitosan and its application

The chitosan-modified glassy carbon electrode can be used as a working electrode for the determination of precious metal elements: Au, Ag, Pt, Pd. In low pH medium, the complex anions of these precious elements combine with the protonated group ---NH₃⁺ in the chitosan molecule in the form of an ion-association complex. These metal ions were selectively enriched and we got sensitive anodic stripping current. These elements content in ore, welding material have been determined by this method. The results were consistent with those from standard sample and ICP atomic emission spectrometry method. The possible mechanism of electrochemical reaction has been proposed by the study of CV, UV and FT-Raman spectrometry.     

Calibrationless determination of cadmium, lead and copper in rain samples by stripping voltammetry at mercury microelectrodes: Effect of natural convection on the deposition step

Mercury microelectrodes were prepared by ex situ deposition of Hg onto Pt microdiscs. By exploiting the known properties of microelectrodes in stripping analysis, an absolute method based on a simple equation derived from the stripping charge and the microelectrode steady-state current was assessed for the simultaneous quantification of Cd²⁺, Pb²⁺ and Cu²⁺ concentrations. The method was tested with synthetic solutions containing known amounts of Cd²⁺, Pb²⁺ and Cu²⁺. Then, it was used to determine the labile and total fractions of these metal ions in rain samples. The labile fractions were measured from samples at their natural pH while the total concentrations were determined from samples at pH=2.     

Electrodeposition of mercury film on electrodes modified with clay minerals

A new type of carbon paste electrode modified with clay mineral and covered with a mercury film is presented in this work. Electrodeposition of the mercury film was performed on the carbon paste electrode modified with montmorillonite. The mercury film was deposited by both electrodeposition in situ and a preliminary electrodeposition. The pre-deposited film of mercury showed to be suitable for anodic stripping voltammetry. An open-circuit sorption of Cd, Pb, and Cu with subsequent anodic stripping voltammetry exhibited higher current responses of metals. Besides the enhanced sensitivity superior separation of the current responses during a simultaneous stripping of metals is expected to be achieved by means of the newly prepared electrode. Presented at the 57th Congress of Chemical Societies, Tatranské Matliare, 4–8 September 2005.     

Use of 3-D plots to avoid mutual interference in bianalyte ASV determinations: application to cadmium and lead detection

We have examined the anodic stripping voltammetry (ASV) of Cd and Pb at carbon screen printed electrodes modified by an in situ deposited Bi film, and have demonstrated significant cross talk between the stripping peaks of the two metals. A simple and generally applicable method for dealing with this problem is described, based on curve-fitting three-dimensional calibration plots using MATLAB. Non-linear fitting to the calibrations produced coefficients of determination R² > 0.99 for both metals. We have illustrated use of the plots in conjunction with Bi-plated electrodes by measuring 15 randomly selected mixtures of Cd and Pb of known concentration.     

Study of Bare and Mercury‐Coated Vibrated Carbon,Gold and Silver Microwire Electrodes for the Determination of Lead and Cadmium in Seawater by Anodic Stripping Voltammetry

Carbon, gold and silver microwires are revisited under vibrated conditions for detection of trace lead and cadmium in seawater. The Pb and Cd peaks fully overlapped on the bare gold and carbon electrodes and partially on the silver electrode. The sensitivity of all three was insufficient for detection in uncontaminated waters. Peak separation was obtained after coating with mercury (Hg). Only the Hg‐coated silver electrode is suitable when preplated. Limits of detection for Pb using the Hg/C and Hg/Ag electrodes (20–40 pM), and Cd (70 pM), are sufficiently low for Pb and Cd detection in seawater.     

聚1,8-萘二胺修饰玻碳电极测定痕量汞

采用电化学聚合的方法制备了聚1,8-萘二胺修饰玻碳电极,建立了吸附富集-阳极溶出伏安法测定痕量Hg2+的新方法.优化了各种实验参数(如富集底液的pH,富集时间等),并考察了其它离子的干扰.在最佳实验条件下,Hg2+在0.001～0.1 mg/L及0.1～5.0 mg/L质量浓度范围内均与溶出峰电流成良好的线性关系,检出限为0.0005 mg/L.该法可用于实际工业废水中汞的测定.