Separation of phenolic acids by capillary electrophoresis with indirect contactless conductometric detection

A new method for the electrophoretic separation of nine phenolic acids (derivatives of benzoic and cinnamic acids) with contactless conductometric detection is presented. Based on theoretical calculations, in which the mobility of the electrolyte co- and counterions and mobility of analytes are taken into consideration, the electrolyte composition and detection mode was selected. This approach was found to be especially valuable for optimization of the electrolyte composition for the separation of analytes having medium mobility. Indirect conductometric detection mode was superior to the direct mode as predicted theoretically. The best performance was achieved with 150 mM 2-amino-2-methylpropanol electrolyte at pH 11.6. The separation was carried out in a counter-electroosmotic mode and completed in less than 6 min. The LODs achieved were about 2.3-3.3 microM and could be further improved to 0.12-0.17 microM by using a sample stacking procedure. The method compares well to the UV-Vis detection.     

Speciation of chromium (III) and chromium (VI) by capillary electrophoresis with contactless conductometric detection and dual opposite end injection

A sensitive, rapid and inexpensive capillary electrophoretic method for the determination of Cr(III) and Cr(VI) species is presented. The method is based on the dual opposite end injection principle and contactless conductometric detection. The sample containing cationic and anionic species is injected into the opposite ends of the separation capillary and after the high voltage is applied, the analytes migrate towards the capillary center, where the cell of a contactless conductivity detector is placed. The method does not require any sample pretreatment, except dilution with deionized water. The separation of Cr(III), Cr(VI) and other common inorganic anions and cations is achieved in less than 4 min. The parameters of the separation electrolyte solution, such as pH and concentration of L-histidine, were optimized. Best results were achieved with electrolyte solution consisting of 4.5 mM L-histidine, adjusted to pH 3.40 with acetic acid. The detection limits achieved for Cr(III) and Cr(VI) were 10 and 39 microg.L(-1), respectively. The repeatability of migration times and peak areas was better than 0.3% and 2.8%, respectively. The developed method was applied to the analyses of rinse water samples from the galvanic industry. The results for the determination of Cr(III) and Cr(VI) were in good agreement with the results obtained by certified differential spectrophotometric method using diphenylcarbazide (CN 83 0520-40) and with the results for the total chromium concentrations determined by electrothermal atomic absorbance spectrometry (ET-AAS) and inductively coupled plasma-mass spectrometry (ICP-MS).     

The Effects of the Electrode System Geometry on the Properties of Contactless Conductivity Detectors for Capillary Electrophoresis

The basic analytical parameters of contactless conductivity detectors with planar, semi‐tubular and tubular electrodes have been compared. It has been found that the differences in the analytical parameters of the detectors are not significant for analytical use. The mean values of baseline peak‐to‐peak noise of 0.27, 0.35 and 0.33 mV, sensitivities of 0.97, 2.08 and 2.27 mV/pg (for K⁺ ion), limits of detection of 0.93, 0.65 and 0.53, and the heights equivalent to a theoretical plate of 2.83, 2.39 and 2.40 μm were obtained for the detectors with planar, semi/tubular and tubular electrodes, respectively. Modifications of the basic detectors, namely a detector with thinned capillary wall and planar electrodes, and a detector with semi‐tubular electrodes placed one against the other on the opposite sides of the capillary were also tested. The configuration with the electrodes placed one against the other permits detector construction with zero gap between the electrodes without increasing the noise; when the electrodes overlap, the detector begins to operate as a permittivity detector.     

Formamide as solvent for capillary zone electrophoresis

A comprehensive investigation of a number of aspects when using formamide as background electrolyte solvent in capillary zone electrophoresis was presented. It included (i) the change of the ion mobility with ionic strength, (ii) the influence of the ionic strength on diffusion coefficients, and (iii) on the separation efficiency expressed by the maximum reachable plate numbers (when only longitudinal diffusion contributed to zone broadening), (iv) the effect of the solvent on pKa values (taken from the literature) of neutral and cation acids, (v) the establishment of the a pH scale in formamide by dissolving acids with known pKa values and their salts at defined proportion (thus circumventing the problem of calibrating the pH meter), (vi) the agreement between the experimentally derived and the theoretical dependence of the effective mobility on pH, (vii) the uptake of water of this hygroscopic solvent from the humidity of the environment and its consequence to the ion mobilities, pKa values, and the chemical stability of the solvent (e.g., hydrolysis), and finally (viii) the use of conductivity and indirect UV absorption to enable detection of analytes below the optical cutoff of formamide.     

A collinear light-emitting diode-induced fluorescence detector for capillary electrophoresis

A novel fluorescence detector based on collinear scheme using a brightness light-emitting diode emitting at 470 nm as excitation source is described. The detector is assembled by all-solid-state optical-electronic components and coupled with capillary electrophoresis using on-column detection mode. Fluorescein isothiocyanate (FITC) and FITC-labeled amino acids and small molecule peptide as test analyte were used to evaluate the detector. The concentration limit of detection for FITC-labeled phenylalanine was 10 nM at a signal-to-noise ratio (S/N) of 3. The system exhibited good linear responses in the range of 1 × 10⁻⁷ to 2 × 10⁻⁵ M (R² = 0.999).     

An integrated light emitting diode-induced fluorescence detector for capillary electrophoresis

An integrated light emitting diode (LED)-induced fluorescence detector was described and evaluated. The LED and its related components including lens and interference filter, the optical fiber used to collect fluorescence, and the capillary column are integrated into a substrate block, which eliminates the need of align procedure of the fiber and the capillary. Forty-fold enhancement of sensitivity was obtained compared with our previous work and the detection limit for fluorescein was 5 nM. Application of the detector for the analysis of FITC-labeled Ephedrine extract was demonstrated.     

Light-emitting-diode-induced fluorescence detector for capillary electrophoresis using optical fiber with spherical end

A simple fluorescence detector for capillary electrophoresis (CE) using a blue light-emitting-diode (LED) as excitation source is constructed and evaluated. An optical fiber was used to collect the fluorescence, and a flat end of the fiber was modified to spherical end, resulting in 50% increase of efficiency over the flat end. A simple device for optical alignment of the fibers and capillary column was designed. The concentration and mass detection limits for fluorescein were 1.8×10⁻⁷ mol l⁻¹ and 4.3 femol, respectively.     

Single‐breath analysis using a novel simple sampler and capillary electrophoresis with contactless conductometric detection

The analysis of ionic content of exhaled breath condensate (EBC) from one single breath by CE with C⁴D is demonstrated for the first time. A miniature sampler made from a 2‐mL syringe and an aluminum cooling cylinder for collection of EBC was developed. Various parameters of the sampler that influence its collection efficiency, repeatability, and effect of respiratory patterns were studied in detail. Efficient procedures for the cleanup of the miniature sampler were also developed and resulted in significant improvement of sampling repeatability. Analysis of EBC was performed by CE‐C⁴D in a 60 mM MES/l ‐histidine BGE with 30 μM CTAB and 2 mM 18‐crown‐6 at pH 6 and excellent repeatability of migration times (RSD < 1.3% (n = 7)) and peak areas (RSD < 7% (n = 7)) of 12 inorganic anions, cations, and organic acids was obtained. It has been shown that the breathing pattern has a significant impact on the concentration of the analytes in the collected EBC. As the ventilatory pattern can be easily controlled during single exhalation, the developed collection system and method provides a highly reproducible and fast way of collecting EBC with applicability in point‐of‐care diagnostics.     

Contactless conductivity detector array for capillary electrophoresis

A CE system featuring an array of 16 contactless conductivity detectors was constructed. The detectors were arranged along 70 cm length of a capillary with 100 cm total length and allow the monitoring of separation processes. As the detectors cannot be accommodated on a conventional commercial instrument, a purpose built set‐up employing a sequential injection manifold had to be employed for automation of the fluid handling. Conductivity measurements can be considered universal for electrophoresis and thus any changes in ionic composition can be monitored. The progress of the separation of Na⁺ and K⁺ is demonstrated. The potential of the system to the study of processes in CZE is shown in two examples. The first demonstrates the differences in the developments of peaks originating from a sample plug with a purely aqueous background to that of a plug containing the analyte ions in the buffer. The second example visualizes the opposite migration of cations and anions from a sample plug that had been placed in the middle of the capillary.     

Parallel and serial dual electrode detectors for capillary electrophoresis

Application of parallel and serial dual electrode detectors for capillary electrophoresis was first described. In parallel dual electrode approach, two 100 μm-diameter Cu disks arranged side by side were used as the dual working electrode for the simultaneous determination of a mixture of carbohydrates and amino acids. In serial dual electrode approach, two working electrodes were arranged in a disk-ring manner for the simultaneous determination of both cysteine and cystine; the disk electrode was Hg/Au serving as the upstream electrode, the ring electrode was 5% CoPC carbon paste serving as the downstream electrode.     

Advances in amperometric and conductometric detection in capillary and chip-based electrophoresis

Amperometric and conductometric detection are currently the two major electrochemical detection modes in capillary and chip electrophoresis. The ease of miniaturization and integration of electrochemical detection elements offers a high potential for the development of portable analytical devices based on electromigrative separations. The challenges and basic concepts of both detection principles in the context of capillary/chip electrophoresis are shortly introduced and milestones of the methodical developments are summarized from a historical perspective. Recent advances and applications are discussed with more detail. Particular attention is paid to new trends in this area of research such as measurements in short capillaries and the enormous progress and increased popularity of contactless conductivity detection. Correspondence: Frank-Michael Matysik, Institute of Analytical Chemistry, University of Leipzig, Linnéstr. 3, D-04103 Leipzig, Germany     

Indirect UV detection of carbohydrates in capillary zone electrophoresis

Summary A new system for the rapid and sensitive analysis of underivatized carbohydrates has been established using capillary zone electrophoresis with indirect UV detection. At an applied potential of 28 kV, sugars and sugar acids could be separated by the combined effects of electroendosmosis and electrophoresis within 20 minutes in a fused silica capillary of 50 m internal diameter and an effective length of 100 cm using 6mM sorbic acid, pH 12.1, as both carrier electrolytie and chromophore. The alkaline pH ensured ionization of the sugars and, hence, their detection by means of charge displacement. Furthermore, the chosen concentration of sorbic acid allowed the smallest fractional change in the background signal to be measured. While the electrophoretic mobilities of the sugars were found to increase within a pH range of 11.9 to 12.3, those of the sugar acids were not affected. Due to the increasing competition of hydroxide ions in the displacement of the chromophore with rising pH, a significant loss of sensitivity is observed at pH values higher than 12.1 and this pH was found to provide sufficient resolution, optimum sensitivity, and a acceptably short analysis time. Under these conditions, a lower detection limit of 2 pmol was obtained for glucose.     

Application of a low impedance contactless conductometric detector for the determination of inorganic cations in capillary monolithic column chromatography

Poly(glycidyl methacrylate) cation exchange monolithic column was prepared in fused-silica capillaries of 320 μm i.d. by thermally initiated radical polymerization and utilized in capillary ion chromatography. With 15 mM methanesulfonic acid as the mobile phase, the separations of a mixture of inorganic cations (Li⁺, Na⁺, NH₄⁺, K⁺) was tested by using a capacitively coupled contactless conductivity detector (C⁴D) and a low impedance C⁴D (LIC⁴D). The LIC⁴D is the series combination of a C⁴D and a quartz crystal resonator. At the resonant frequency of the series combination, the capacitor impedance from capillary wall was offset by the inductance impedance from the quartz crystal resonator. A minimum impedance was obtained in the impedance-frequency curve of the combination. The responses of the C⁴D and LIC⁴D were analyzed based on an equivalent circuit model. It was shown that the sensitivity of the C⁴D to the change in analyte concentration is rather poor due to the high ratio of the impedance from the capillary wall capacitor to the solution impedance. The LIC⁴D has the similar sensitivity as a contact conductivity detector but a much smaller cell volume. The on-column detection model was realized by LiC⁴D without preparation of optical detection window in monolithic column.     

Evaluation of the detection of biomolecules in capillary electrophoresis by contactless conductivity measurement

The sensitivity of contactless conductivity detection to amino acids, peptides and proteins in CE was studied for BGE solutions of different pH values. The LOD and analytical characteristics were compared for acidic and basic conditions and better results were in most cases found for buffers of low pH values. Linear dynamic ranges varied between two orders of magnitude for amino acids and peptides and three orders of magnitude for larger proteins. The concentration detection limits were found to be between 1.2 and 7.5 microM for the amino acids tested and for the larger molecules they varied between 2.6 microM for leucine enkephalin and 0.2 microM for HSA when using a buffer at pH 2.1.     

Separation of perfluorocarboxylic acids using capillary electrophoresis with UV detection

A capillary electrophoretic method with UV detection for separation and quantitation of perfluorocarboxylic acids (PFCAs) from C6-PFCA to C12-PFCA has been developed. The optimization of measurement conditions included the choice of the most appropriate type and concentration of buffer in the background electrolyte (BGE), as well as the type and the content of an organic modifier. The optimal separation of investigated PFCAs was achieved with 50 mM phosphate buffer and 40% isopropanol in the BGE using direct UV detection. The optimum wavelength for direct UV detection was optimized at 190 nm. For indirect detection, several chromophores were studied. Five mM 3,5-Dinitrobenzoic acid (3,5-DNBA) in 20 mM phosphate buffer BGE and indirect UV detection at 280 nm gave the optimal detection and separation performance for the investigated PFCAs. The possibility of on-line preconcentration of solutes by stacking has been examined for indirect detection. The detection limits (LODs) determined for direct UV detection ranged from 2 microg/mL for C6-PFCA to 33 microg/mL for C12-PFCA. The LODs obtained for indirect UV detection were comparable to those obtained for direct UV detection.     

甲氧苄啶的毛细管电泳快速检测新方法

建立了毛细管电泳高频电导法测定药物和尿液中的甲氧苄啶。考察了各种条件对分离和检测的影响。以4.0 mmol/L HAc 体积分数10%甲醇(pH4.0)为电泳介质,分离电压20.0 kV,重力虹吸进样。在优化条件下,甲氧苄啶峰形良好,出峰时间小于6 min,线性范围为1.5~120.0μg/mL,检出限0.5μg/mL。该方法样品处理过程简单,可用于药物制剂的质量控制和临床检验。     

Microchip capillary electrophoresis with electrochemical detector for fast measurements of aromatic amino acids

A method based on microchip capillary electrophoresis with amperometric detection was developed for the rapid separation and direct detection of oxidizable aromatic amino acids (without prior derivatization). The working electrode was a thick-film carbon strip electrode positioned opposite the outlet of the separation channel. Factors influencing the separation and detection processes were examined and optimized. The five aromatic amino acids, tyrosine, 5-hydroxytryptophan, tryptophan, p-aminobenzoic acid, and m-aminobenzoic acid, can be well separated within 5 min using a separation voltage of 2000 V and a 25 mM phosphate buffer (pH 7.0) run buffer containing 50 mM sodium dodecylsulfate. Most favorable amperometric detection was obtained at +0.95 V. Linear calibration plots are observed for micromolar concentrations of the oxidizable amino acids. The new protocol offers good stability and for reproducibility, with relative S.D. of less than 5% for both migration times and peak currents (n=8). It should be useful for the analysis of aromatic amino acids, as desired for life sciences.     

Determination of different classes of amines with capillary zone electrophoresis and contactless conductivity detection

The use of contactless conductivity detection for the determination of different organic amines in CE was successfully demonstrated. Aliphatic non UV-absorbing species could be determined along absorbing compounds by measuring the conductivity of their protonated forms. The species tested included short-chained aliphatic primary, secondary and tertiary amines, branched aliphatic amines, diamines, hydroxyl-substituted amines as well as species incorporating aromatic and non-aromatic cyclic moieties. Highest sensitivity was obtained with BGE solutions containing solely acetic acid. A concentration of 0.5 M at a pH value of 2.5 was used. Detection limits were in the order of 1 microM. Complete separation of cis- and trans-1,2-diaminocyclohexane could be achieved by adding 18-crown-6 as modifier to the electrolyte solution.     

Electrochemical detector based on sol-gel-derived carbon composite material for capillary electrophoresis microchips

An on-chip disk electrode based on sol-gel-derived carbon composite material could be easily and reproducibly fabricated. Unlike other carbon-based electrodes reported previously, this detector is rigid, convenient to fabricate, and amenable to chemical modifications. Based on the stable and reproducible characters of this detector, a copper particle-modified detector was developed for the detection of carbohydrates which extends the application of the carbon-based electrode. In our experiments, the performance of the new integrated detector for rapid on-chip measurement of epinephrine and glucose was illustrated. Experimental procedures including the fabrication of this detector, the configuration of separation channel outlet and electrode verge, and the performance characteristics of this new electrochemical detector were investigated.     

Optimization of background electrolyte composition for simultaneous contactless conductivity and fluorescence detection in capillary electrophoresis of biological samples

In this article, optimization of BGE for simultaneous separation of inorganic ions, organic acids, and glutathione using dual C⁴D‐LIF detection in capillary electrophoresis is presented. The optimized BGE consisted of 30 mM 2‐[4‐(2‐hydroxyethyl)piperazin‐1‐yl]ethanesulfonic acid, 15 mM 2‐amino‐2‐hydroxymethyl‐propane‐1,3‐diol, and 2 mM 18‐crown‐6 at pH 7.2 and allowed simultaneous separation of ten inorganic anions and cations, three organic acids and glutathione in 20 min. The samples were injected hydrodynamically from both capillary ends using the double‐opposite end injection principle. Sensitive detection of anions, cations, and organic acids with micromolar LODs using C⁴D and simultaneously glutathione with nanomolar LODs using LIF was achieved in a single run. The developed BGE may be useful in analyses of biological samples containing analytes with differing concentrations of several orders of magnitude that is not possible with single detection mode.