维生素B_1自组装膜修饰金电极对多巴胺、尿酸的电催化作用

用维生素B1(VB1)在金电极上进行自组装,制备了VB1自组装膜修饰金电极(VB1-Au/SAMs/CME).利用循环伏安法初步研究了此自组装单分子膜修饰电极的电化学行为.结果表明: VB1在金电极表面具有特性吸附.以\3-/ 4-氧化还原电对为探针,考察了VB1自组装膜修饰金电极的电化学性质, VB1自组装膜的存在对\3-/4-的电子转移具有明显的阻碍作用.研究了多巴胺(DA)和尿酸(UA)在此电极上的电化学行为.实验结果表明, DA和UA在此电极上均可被电催化氧化.差分脉冲伏安(DPV)氧化峰电流与DA浓度在2.0×10-5～4.0×10-4 mol/L范围内呈线性关系;测定UA的线性范围为6.0×10-5～2.2×10-4 mol/L,而且可实现这两种物质的同时测定.     

维生素B6在维生素B12修饰电极上的电化学行为及其分析应用

采用循环伏安法研究了维生素B6在维生素B12修饰玻碳电极上的电化学行为,建立了测定痕量维生素B6的新方法.在pH 8.6的NH3-NH4Cl缓冲溶液中,维生素B6在修饰电极上产生一个灵敏的氧化峰,采用差分脉冲伏安法测定,其氧化峰电流与维生素B6的浓度在8.0×10-7～2.0×10-4 mol/L范围内呈良好的线性关系,检出限为2.0×10-7 mol/L.该修饰电极具有良好的选择性、灵敏度及稳定性,用于片剂中维生素B6的定量分析,结果令人满意.     

Multiwalled Carbon Nanotubes‐Chitosan Modified Single‐Use Biosensors for Electrochemical Monitoring of Drug‐DNA Interactions

A multiwalled carbon nanotubes (CNT)‐chitosan (CHIT) modified pencil graphite electrode (CNT‐CHIT/PGE) was developed for the first time herein for electrochemical monitoring of the interaction of an anticancer drug, mitomycin C (MC) and DNA. The characterization of unmodified PGE, CHIT/PGE, CNT/PGE and CHIT‐CNT/PGE were performed by scanning electron microscopy and cyclic voltammetry techniques. The oxidation signals of MC and guanine were measured before and after interaction at the surface of CNT‐CHIT/PGEs using differential pulse voltammetry. Electrochemical impedance spectroscopy technique was also successfully utilized for monitoring of the interaction process at the surface of CNT‐CHIT/PGEs in different interaction times.     

Interaction of Mitomycin C with DNA Immobilized onto Single‐walled Carbon Nanotube/Polymer Modified Pencil Graphite Electrode

The electrochemical investigation of the interaction between the anticancer drug mitomycin C (MC) and DNA was described using a single‐walled carbon nanotube (SWCNT)/poly(vinylferrocenium) (PVF⁺) modified pencil graphite electrode (PGE). The electrochemical oxidation signals of guanine were monitored before and after the interaction between MC and DNA by using differential pulse voltammetry. The effects of DNA and MC concentration and MC interaction time were examined based on the electrode response. Cyclic voltammetry and electrochemical impedance spectroscopy were used for the characterization of SWCNT/PVF⁺ modified and PVF⁺ modified PGEs. The detection limit corresponded to 625 ng/mL for MC using calf thymus double‐stranded DNA immobilized SWCNT/PVF⁺ modified PGE.     

Electrochemical sensor for ultrasensitive determination of ceftazidime using hollow platinum nanoparticles/reduced graphene oxide/pencil graphite electrode

In this paper, an electrochemical sensor was prepared based on the modification of pencil graphite electrode (PGE) by hollow platinum nanoparticles/reduced graphene oxide (HPtNPs/rGO/PGE) for determination of ceftazidime (CFZ). Initially, rGO was electrodeposited on the electrode surface, and then, hollow platinum nanoparticles were placed on the electrode surface via galvanic displacement reaction of Pt(IV) ions with cobalt nanoparticles (CoNPs) that had electrodeposited on the electrode surface. Several significant parameters controlling the performance of the HPtNPs/rGO/PGE were examined and optimized using central composite design as one optimization methodology. The surface morphology and elemental characterization of the bare PGE, rGO/PGE, CoNPs/rGO/PGE, and HPtNPs/rGO/PGE-modified electrodes was analyzed by field-emission scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electrochemical impedance spectroscopy. The electrochemical activity of CFZ on resulting modified electrode was investigated by cyclic voltammetry (CV) and adsorptive differential pulse voltammetry (AdDPV). Adsorptive differential pulse voltammetry indicates that peak current increases linearly with respect to increment in CFZ concentration. CFZ was determined in the linear dynamic range of 5.0 × 10^?13 to 1.0 × 10^?9 M, and the detection limit was determined as 2.2 × 10^?13 M using AdDPV under optimized conditions. The results showed that modified electrode has high selectivity and very high sensitivity. The method was used to determine of CFZ in drug injection and plasma samples.     

基于纳米金／壳聚糖掺杂碳纳米管修饰金电极非标记免疫传感器的研究

应用吸附法将羊抗人IgG抗体直接固定于纳米金(GNPs)/壳聚糖(Chit)掺杂碳纳米管(CNTs)修饰的金电极表面,制备了用于人IgG抗原检测的非标记电化学免疫传感器.利用循环伏安法和交流阻抗研究了修饰电极表面的电化学特性,用差分脉冲伏安法研究了测试底液的pH值对免疫传感器性能的影响.实验表明,在含不同浓度人IgG的...     

微过氧化物酶-11在壳聚糖修饰玻碳电极上的电化学

采用物理吸附法, 将微过氧化物酶-11(MP-11)固定在载体壳聚糖修饰的玻碳电极表面. 运用循环伏安法对MP-11在该修饰电极上的直接电化学行为及对氧(O2)和过氧化氢(H2O2)的电催化行为进行了表征. 研究结果表明, 在pH=7.12的磷酸盐缓冲溶液中, 壳聚糖修饰电极上的MP-11发生了准可逆的氧化还原反应, 而且在反应过程中包含质子的传递过程, 完全实现了MP-11在该修饰电极上的直接电化学. 该修饰电极也可以对O2和H2O2进行电催化还原, 并且两个反应的电催化还原过程都是受表面控制的电化学过程, 对H2O2催化还原产生的响应电流与H2O2的浓度呈线性关系.     

Titanium Dioxide/Multi-walled Carbon Nanotubes Composite Modified Pencil Graphite Sensor for Sensitive Voltammetric Determination of Propranolol in Real Samples

A very effective electrochemical sensor for the analysis of propranolol was constructed using TiO₂/MWCNT film deposited on the pencil graphite electrode as modifier. The modified electrode represented excellent electrochemical properties such as fast response, high sensitivity and low detection limit. The proposed sensor showed an excellent selective response to propranolol in the presence of foreign species and other drugs. The electrochemical features of the modified electrode were investigated by cyclic voltammetry and electrochemical impedance spectroscopy (EIS) technique which indicated a decrease in resistance of the modified electrode versus bare PGE and MWCNT/PGE. The surface morphology for the modified electrode was determined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and Fourier transform infrared spectroscopy (FT-IR). Differential pulse technique (DPV) was used to determine propranolol which showed a good analytical response in the linear range of 8.5×10⁻⁸-6.5×10⁻⁶ M with a limit of detection 2.1×10⁻⁸ M. The TiO₂/MWCNT/PGE sensor was conveniently applied for the measurement of propranolol in biological and pharmaceutical media.     

Electrochemical detection of DNA damage induced by in situ generated bisphenol A radicals through electro-oxidation

A glassy carbon electrode was modified with dsDNA and a nanocomposite composed of multi-walled carbon nanotubes and chitosan (MWNT-chit). The electrode was applied to the electrochemical detection of DNA damage as induced by in situ generated bisphenol A (BPA) radicals through electro-oxidation. The modified electrode was characterized by cyclic voltammetry and electrochemical impedance spectroscopy. The results indicate that MWNT-chit nanocomposite represents a viable platform for the immobilization of DNA that effectively promotes electron transfer between DNA and the electrode. The mode of interaction between DNA and BPA was investigated by differential pulse voltammetry and UV-vis spectrophotometry, indicating that the dominant interaction is intercalation. In order to explore the mechanism of damage caused by BPA radicals, the electro-oxidation of BPA at the modified glass electrode was investigated. Based on the signal for guanine without any other external indicator, DNA damage was investigated through the electro-oxidation of BPA.     

基于多壁碳纳米管/壳聚糖多层膜修饰玻碳电极邻苯二酚的测定

改进了碳纳米管在壳聚糖溶液中的分散方法,制备了多壁碳纳米管/壳聚糖多层膜修饰玻碳电极,对比了不同修饰层数膜电极的循环伏安和电化学阻抗行为,5层多壁碳纳米管/壳聚糖膜修饰玻碳电极的电化学性能优良.在最优实验条件下,该修饰玻碳电极对邻苯二酚(CAT)有灵敏的响应,CAT浓度在3.99×10-6～9.09×10-4mol/L范围内与氧化峰电流呈良好的线性关系,检出限为2.39×10-6mol/L(S/N=3).该修饰玻碳电极性能稳定,测定4×10-5mol/LCAT溶液,RSD(n=10)为2.1%;15周后,该电极的响应值仅降低1.9%.     

巯基化改性壳聚糖在电化学生物传感器制备中的应用

以壳聚糖、N-乙酰-L-半胱氨酸(NAC)为原料,以1-羟基苯并三唑(HOBt)和1-乙基-3-(3-二甲基胺丙基)碳化二亚胺盐酸盐(EDAC)为缩合剂,合成功能化壳聚糖衍生物巯基壳聚糖(CHS-NAC).用红外光谱(FTIR)、核磁共振(1H-NMR)及X射线衍射(XRD)对其结构进行表征,用Ellman’s试剂通过标准曲线法测得巯基含量.利用CHS-NAC的黏附性,通过层层吸附的方法将CHS-NAC、纳米金及细胞色素c分别修饰到玻碳电极(GC)上,通过扫描电子显微镜(SEM)对修饰电极表面的形貌进行了观察,采用循环伏安和电化学阻抗研究了不同修饰膜电极的电化学行为,及扫描速率对细胞色素c修饰电极的影响,并开展了对过氧化氢的电催化分析.实验结果表明,CHS-NAC能高效地将纳米金及细胞色素c固定在电极表面,并能有效发挥纳米金辅助转移电子及细胞色素c对过氧化氢催化的能力.     

High‐sensitive Electrochemical Determination of Ethyl Carbamate Using Urethanase and Glutamate Dehydrogenase Modified Electrode

An amperometric biosensor for ethyl carbamate (EC) was developed for the first time through the cascade reactions of urethanase and glutamate dehydrogenase (GLDH). Urethanase decomposes ethyl carbamate to produce ammonia, which converts to L‐glutamate under the catalysis of GLDH in the presence of α‐ketoglutarate and NADH. Then the change of NADH can be detected chronoamperometrically. The two enzymes were entrapped into chitosan/gelatine/γ‐glycidoxy propyl trimethoxy silane sol‐gel and immobilized on the surface of pyrolytic graphite electrode (PGE). The modified electrode was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Under the optimized conditions, the amperometric EC biosensor exhibits a linear detection range from 0.5 to 40 μM with a low detection limit of 5.30 nM. The biosensor was successfully used to detect EC in mimic Chinese rice wine samples, and satisfactory recovery and relative standard deviation were achieved.     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Selective Electrochemical Determination of Salicylic Acid in Wheat Using Molecular Imprinted Polymers

Salicylic acid is a phytohormone, playing crucial roles in signal transduction, crop growth, and development, and defense to environmental challenges. In this study, a highly selective electrochemical sensor was designed and used to determine salicylic acid using molecularly imprinted polymers for recognition. The electrochemical sensor was fabricated via stepwise modification of gold nanoparticle–graphene–chitosan and molecularly imprinted polymers on a glassy carbon electrode. With electrochemical deposition, a gold nanoparticle–graphene–chitosan film was deposited on the glassy carbon electrode and enhanced the sensitivity. Molecularly imprinted polymers with adsorbed template salicylic acid were added to the surface of the modified electrode. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the modified electrodes. Salicylic acid in wheat was quantified by the sensor using the molecularly imprinted polymer/gold nanoparticle–graphene–chitosan/glassy carbon electrode. Concentrations of salicylic acid from 5?×?10^?10 to 5?×?10^?5?mol?L^?1 were determined showing that the developed sensor was suitable for the analysis of food.     

Development of Simple Electrochemical Sensor for Selective Determination of Methadone in Biological Samples Using Multi‐walled Carbon Nanotubes Modified Pencil Graphite Electrode

The electrochemical sensor was developed for determination of methadone (MTD) using multi‐walled carbon nanotubes (MWCNT) modified pencil graphite electrode (MWCNT‐PGE). It was found that the oxidation peak current of MTD at the MWCNT‐PGE was greatly improved compared with that of the bare‐PGE. At the MWCNT‐PGE, well‐defined anodic peak of MTD was observed at about 0.7 V (in pH 7 solution). The influence of several parameters on the determination of MTD was investigated. At optimum experimental conditions, differential pulse voltammetry (DPV) was used for determination of MTD, which exhibited a linear calibration graph of Ip versus MTD concentration in the range of 0.1–15 µM with a correlation coefficient of 0.9992. The calculated detection limit for S/N = 3 was 87 nM. It has been shown that the peaks obtained for oxidation of ascorbic acid (AA), uric acid (UA) and MTD in their mixture could be well resolved by differential pulse voltammetry, permitting us to develop a sensitive and selective electrochemical sensor for determination of MTD in the presence of AA and UA. Finally, MWCNT‐PGE was used for determination of MTD in biological samples, such as human serum and urine, using the standard addition procedure and the results were quite promising.     

Electrochemical determination of methimazole based on the acetylene black/chitosan film electrode and its application to rat serum samples

A novel method has been developed for the determination of methimazole, which was based on the enhanced electrochemical response of methimazole at the acetylene black/chitosan composite film modified glassy carbon electrode. The electrochemical behavior of methimazole was studied at this film electrode by cyclic voltammetry and differential pulse voltammetry. The experimental results showed that methimazole exhibited a remarkable oxidation peak at 0.63V at the film electrode. Compared with the bare glassy carbon electrode, the oxidation peak current increased greatly, and the peak potential shifted negatively, which indicated that the acetylene black/chitosan film electrode had good catalysis to the electrochemical oxidation of methimazole. The enhanced oxidation current of methimazole was indebted to the nano-porus structure of the composite film and the enlarged effective electrode area. The influences of some experimental conditions on the oxidation of methimazole were tested and the calibration plot was examined. The results indicated that the differential pulse response of methimazole was linear with its concentration in the range of 1.0×10(-7) to 2.0×10(-5)mol/L with a linear coefficient of 0.998, and in the range of 4.0×10(-5) to 3.0×10(-4)mol/L with a linear coefficient of 0.993. The detection limit was 2.0×10(-8)mol/L (S/N=3). The film electrode was used to detect the content of methimazole in rat serum samples by the standard addition method with satisfactory results.     

基于羧基化碳纳米管修饰电极伏安法同时测定痕量锢和铝

基于羧基化多壁碳纳米管(c-MWCNT),制备了可同时测定In3+和Al3+的新型碳材料修饰电极.利用循环伏安法(CV)和交流阻抗法(EIS)对此修饰电极进行了表征,用线性扫描伏安法(LSV)研究了In3+与Al3+共存于修饰电极上的电化学行为.与裸玻碳电极相比,新型碳材料修饰电极的电化学活性得到很大提高;In3+与A...     

Carbon Nanotubes Modified Graphite Electrodes for Monitoring of Biointeraction Between 6‐Thioguanine and DNA

In this present study, single‐walled carbon nanotubes (SWCNT) modified disposable pencil graphite electrodes (SWCNT‐PGEs) were developed for the electrochemical monitoring of anticancer drug, and its interaction with double stranded DNA (dsDNA). Under this aim, SWCNT‐PGEs were applied for the first time in the literature to analyse of 6‐Thioguanine (6‐TG), and also to investigate its interaction with DNA by voltammetric and impedimetric methods. The surface morphologies of PGE and SWCNT‐PGE were explored using scanning electron microscopy (SEM) and electrochemical characterization of unmodified/modified electrodes was performed by cyclic voltammetry (CV). Experimental parameters; such as, the concentration of 6‐TG and its interaction time with dsDNA were optimized by using differential pulse voltammetry (DPV). Additionally, the interaction of 6‐TG with dsDNA was studied in case of different interaction times by electrochemical impedance spectroscopy (EIS) in contrast to voltammetric results. The detection limit of 6‐TG was found to be 0.25 μM by SWCNT‐PGE.     

A Selective Simultaneous Determination of Levodopa and Serotonin Using a Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotube/Chitosan Composite

A glassy carbon electrode (GCE) modified with carbon nanotube/chitosan (MWCNTs‐CHT/GCE) was used for the sensitive voltammetric determination of levodopa (Lev) and serotonin (Ser). The measurements were carried out using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and chronoamperometry (CA). Under the optimum conditions the electrode provides a linear response versus Lev and Ser concentrations in the range of 2.0–220.0 µM and 0.5–130.0 µM, respectively, using DPV. The modified electrode was satisfactorily used for determination of Lev and Ser in human serum and urine with satisfactory results.     

Fabrication of Chitosan‐Multiwall Carbon Nanotube Nanocomposite Containing Ferri/Ferrocyanide: Application for Simultaneous Detection of D‐Penicillamine and Tryptophan

We report a simple and effective strategy for fabrication of the nanocomposite containing chitosan (CS) and multiwall carbon nanotube (MWNT) coated on a glassy carbon electrode (GCE). The characterization of the modified electrode (CS‐MWNT/GC) was carried out using scanning electron microscopy (SEM) and UV–vis absorption spectroscopy. The electrochemical behavior of CS‐MWNT/GC electrode was investigated and compared with the electrochemical behavior of chitosan modified GC (CS/GC), multiwalled carbon nanotube modified GC (MWNT/GC) and unmodified GC using cyclic voltammetry (CV) and electron impedance spectroscopy (EIS). The chitosan films are electrochemically inactive; similar background charging currents are observed at bare GC. The chitosan films are permeable to anionic Fe(CN)₆^3?/4? (FC) redox couple. Electrochemical parameters, including apparent diffusion coefficient for the Fe(CN)₆^3?/4? redox probe at FC/CS‐MWNT/GC electrode is comparable to values reported for cast chitosan films. This modified electrode also showed electrocatalytic effect for the simultaneous determination of D‐penicillamine (D‐PA) and tryptophan (Trp). The detection limit of 0.9 μM and 4.0 μM for D‐PA and Trp, respectively, makes this nanocomposite very suitable for determination of them with good sensitivity.