A polyamine coating for enhanced capillary electrophoresis-electrospray ionization-mass spectrometry of proteins and peptides

A procedure for enhanced capillary electrophoresis-electrospray ionization-mass spectrometry (CE-ESI-MS) of proteins is presented. The use of a newly presented capillary coating, PolyE-323, provided fast separations of typically a few minutes with high efficiency, good deactivation, and no bleeding into the mass spectrometer. Capillaries coated with PolyE-323 showed high stability over a range of pH 2-10, and tolerance towards methanol and acetonitrile, two modifiers commonly used in CE-ESI-MS. Due to the speed and simplicity of the coating procedure, the polymeric surface could, if necessary, easily be regenerated. This capability is especially valuable when working with samples of complex matrix, where a capillary surface cleaning step might be desired in order to eliminate possible memory effects. The potential of PolyE-323-coated capillaries in bioanalysis using CE-ESI-MS was demonstrated by analyzing peptides and proteins up to 66 kDa using time of flight (TOF)-MS. Due to the stable, anodal electroosmotic flow generated by the coating, the use of a sheathless ESI interface was enabled, demonstrated in peptide analysis with attomole sensitivity. The fast on-line CE-ESI-TOF system using PolyE-323-coated capillaries provided efficient separation and detection of a large number of peaks in a short time, exemplified by the analysis of a tryptic digest of bovine serum albumin (BSA). The capability of the developed capillary surface coating was demonstrated by the separation of human plasma and cerebrospinal fluid (CSF).     

Integration of immobilized trypsin bead beds for protein digestion within a microfluidic chip incorporating capillary electrophoresis separations and an electrospray mass spectrometry interface

A microfluidic device is described in which an electrospray interface to a mass spectrometer is integrated with a capillary electrophoresis channel, an injector and a protein digestion bed on a monolithic substrate. A large channel, 800 microm wide, 150 microm deep and 15 mm long, was created to act as a reactor bed for trypsin immobilized on 40-60 microm diameter beads. Separation was performed in channels etched 10 microm deep, 30 microm wide and about 45 mm long, feeding into a capillary, attached to the chip with a low dead volume coupling, that was 30 mm in length, with a 50 microm i.d. and 180 microm o.d. Sample was pumped through the reactor bed at flow rates between 0.5 and 60 microL/min. The application of this device for rapid digestion, separation and identification of proteins is demonstrated for melittin, cytochrome c and bovine serum albumin (BSA). The rate and efficiency of digestion was related to the flow rate of the substrate solution through the reactor bed. A flow rate of 1 or 0.5 microL/min was found adequate for complete consumption of cytochrome c or BSA, corresponding to a digestion time of 3-6 min at room temperature. Coverage of the amino acid sequence ranged from 92% for cytochrome c to 71% for BSA, with some missed cleavages observed. Melittin was consumed within 5 s. In contrast, a similar extent of digestion of melittin in a cuvet took 10-15 min. The kinetic limitations associated with the rapid digestion of low picomole levels of substrate were minimized using an integrated digestion bed with hydrodynamic flow to provide an increased ratio of trypsin to sample. This chip design thus provides a convenient platform for automated sample processing in proteomics applications.     

A strategy for screening trypsin inhibitors from traditional Chinese medicine based on a monolithic capillary immobilized enzyme reactor coupled with offline liquid chromatography and mass spectrometry

A novel strategy was successfully developed for screening trypsin inhibitors in traditional Chinese medicines based on monolithic capillary immobilized enzyme reactors combined with liquid chromatography‐tandem mass spectrometry. Organic polymer based monolithic enzyme reactors were firstly prepared by covalently bonding trypsin to a poly(glycidyl methacrylate‐co‐poly (ethylene glycol) diacrylate) monolith by the ring‐opening reaction of epoxy groups. The activity and kinetic parameters of the obtained monolithic trypsin reactors were systematically evaluated using micro‐liquid chromatography. Fourier transform infrared spectroscopy and scanning electron microscopy were also used to characterize the monolithic trypsin reactors. The resulting functional and denatured monolithic trypsin reactors were applied as affinity solid‐phase extraction columns, and offline coupled with a liquid chromatography‐tandem mass spectrometry system to construct a binding affinity screening platform. Subsequently, the proposed platform was applied for screening trypsin binders in a Scutellaria baicalensis Georgi extract. Three compounds, namely scutellarin, baicalin, and wogonoside were identified, and their inhibitory activities were further confirmed via an in vitro enzymatic inhibition assay. Additionally, molecular docking was also performed to study the interactions between trypsin and these three compounds.     

Capillary electrophoresis off-line matrix-assisted laser desorption/ionisation mass spectrometry of intact and digested proteins using cationic-coated capillaries

Capillary electrophoresis (CE) was coupled off-line with matrix-assisted laser desorption/ionisation time-of-flight mass spectrometry (MALDI-TOFMS) for the analysis of proteins and peptides. CE fractions were collected directly on a matrix-coated MALDI target, using a sheath-flow interface. Protein adsorption during CE separations was prevented by coating the capillaries with the physically adsorbed, cationic polymer PolyE-323. The CE/MALDI-MS system was used for the analysis of model proteins and peptides at physiological pH as well as analysis of proteins in tear fluid. Moreover, tryptic on-target digestion of the collected protein fractions, with subsequent MALDI-MS and MS/MS peptide analysis, was demonstrated.     

Microchip extraction of catecholamines using a boronic acid functional affinity monolith

A novel solid phase extraction microchip with a boronic acid functional affinity monolithic disc was developed in this work. Vinyl phenylboronic acid–ethylene glycol dimethacrylate co-polymer monoliths, which have pore sizes up to 20 μm, were investigated for extraction of catecholamines using adsorption and desorption studies in a batch system. Desorption yields of greater than 90% were achieved for catecholamines at pH 3 and below. Monolithic discs were then formed in chambers in borofloat glass microfluidic chips using in situ UV polymerization. Adsorption on the monolithic discs was performed via electrokinetic flow, with catecholamines determined via laser-induced native fluorescence (LINF) detection following electrokinetic elution. Microchips containing the boronic acid functional polymer discs worked well for extraction of catecholamines, providing greater than 100 fold concentration enrichment. This study demonstrated that a solid phase extraction microchip, containing an easily prepared monolith disc, will be useful for boronate affinity extraction of cis-diol containing compounds.     

Immobilization of trypsin on sub-micron skeletal polymer monolith

A new kind of immobilized trypsin reactor based on sub-micron skeletal polymer monolith has been developed. Covalent immobilization of trypsin on this support was performed using the epoxide functional groups in either a one- or a multi-step reaction. The proteolytic activity of the immobilized trypsin was measured by monitoring the formation of N-α-benzoyl-L-arginine (BA) which is the digestion product of a substrate N-α-benzoyl-L-arginine ethyl ester (BAEE). Results showed that the digestion speed was about 300 times faster than that performed in free solution. The performance of such an enzyme reactor was further demonstrated by digesting protein myoglobin. It has been found that the protein digestion could be achieved in 88 s at 30°C, which is comparable to 24 h digestion in solution at 37°C. Furthermore, the immobilized trypsin exhibits increased stability even after continuous use compared to that in free solution. The present monolithic enzyme-reactor provides a promising platform for the proteomic research.     

Development and validation of polymerized high internal phase emulsion monoliths coupled with HPLC and fluorescence detection for the determination of trace tetracycline antibiotics in environmental water samples

A polymerized high internal phase emulsion monolith was used as a novel sorbent for solid‐phase extraction coupled with high‐performance liquid chromatography and fluorescence detection for the determination of oxytetracycline, tetracycline, doxycycline, and chlorotetracycline in environmental water samples. The polymerized high internal phase emulsion monolithic column was prepared by the in situ polymerization of the continuous phase of a high internal phase emulsion containing glycidyl methacrylate, styrene, and divinylbenzene in pipette tips, and then functionalized with iminodiacetic acid. The resulting monolith exhibited highly interconnected porosity and large surface areas, making it an excellent candidate as an solid‐phase extraction sorbent for the enrichment of trace tetracycline antibiotics. Several factors affecting the extraction performance of polymerized high internal phase emulsion monoliths, including the pH of sample solution, the eluting solvents, the sample loading flow rate and volume, were investigated, respectively. Under the optimized conditions, the mean recoveries of oxytetracycline, tetracycline, doxycycline, and chlorotetracycline spiked in pond and farm wastewater samples ranged from 78.1 to 119.3% with relative standard deviation less than 15%. The detection limits (S/N = 3) of the proposed method were in the range of 51–137 pg/mL. This study demonstrated that the monolithic polymerized high internal phase emulsion would be promising solid‐phase extraction sorbents in the extraction and proconcentration of trace analytes from complex samples.     

Design and evaluation of synthetic silica-based monolithic materials in shrinkable tube for efficient protein extraction

Sample pretreatment is a required step in proteomics in order to remove interferences and preconcentrate the samples. Much research in recent years has focused on porous monolithic materials since they are highly permeable to liquid flow and show high mass transport compared with more common packed beds. These features are due to the micro-structure within the monolithic silica column which contains both macropores that reduce the back pressure, and mesopores that give good interaction with analytes. The aim of this work was to fabricate a continuous porous silica monolithic rod inside a heat shrinkable tube and to compare this with the same material whose surface has been modified with a C(18) phase, in order to use them for preconcentration/extraction of proteins. The performance of the silica-based monolithic rod was evaluated using eight proteins; insulin, cytochrome C, lysozyme, myoglobin, β-lactoglobulin, ovalbumin, hemoglobin, and bovine serum albumin at a concentration of 60 μM. The results show that recovery of the proteins was achieved by both columns with variable yields; however, the C(18) modified silica monolith gave higher recoveries (92.7 to 109.7%) than the non-modified silica monolith (25.5 to 97.9%). Both silica monoliths can be used with very low back pressure indicating a promising approach for future fabrication of the silica monolith inside a microfluidic device for the extraction of proteins from biological media.     

金属-有机骨架MIL-101(Cr)掺杂聚合物整体柱的制备及其用于酚类化合物的在线固相萃取

制备了金属-有机骨架（MOF）MIL-101（Cr）掺杂聚合物整体柱，建立了在线固相萃取-高效液相色谱检测水中4-硝基苯酚、2-硝基苯酚、3-甲基苯酚和2，4-二氯苯酚的方法。考察了样品溶液pH值、上样时间、上样流速和解吸时间对酚类化合物萃取效果的影响。在最优萃取条件下，采用制备的整体柱检测水中酚类化合物，其富集因子高，线性范围宽，精密度好，检出限低，适用于水中酚类化合物的检测。制备掺杂聚合物整体柱是促进和拓宽MOFs在线固相萃取应用的有效方法之一。     

Multifunctional protein processing chip with integrated digestion, solid-phase extraction, separation and electrospray

We describe a microfluidic device in which integrated tryptic digestion, SPE, CE separation and electrospray ionization for MS are performed. The chip comprised of 10 × 30 μm channels for CE, and two serially connected 150?μm deep, 800?μm wide channels packed with 40 to 60 μm diameter beads, loaded with either immobilized trypsin, reversed-phase packing or both. On-chip digestion of cytochrome c using the trypsin bed showed complete consumption of the protein in 3 min, in contrast to the 2 h required for conventional solution phase tryptic digestion. SPE of 0.25 μg/mL solutions of the peptides leu-enkephalin, angiotensin II and LHRH gave concentration enhancements in the range of 4.4-12, for a ten times nominal volume ratio. A 100 nM cytochrome c sample concentrated 13.3 times on-chip gave a sequence coverage of 85.6%, with recovery values ranging from 41.2 to 106%. The same sample run without SPE showed only five fragment peaks and a sequence coverage of 41.3%. When both on-chip digestion and SPE (13.3 volume ratio concentration enhancement) were performed on 200 nM cytochrome c samples, a sequence coverage of 76.0% and recovery values of 21-105% were observed. Performing on-chip digestion alone on the same sample gave only one significant fragment peak. The above digestion/peptide concentration step was compared to on-chip protein concentration by SPE followed by on-chip digestion with solution phase trypsin. Both procedures gave similar recovery results; however, much larger trypsin autodigestion interference in the latter approach was apparent.     

固定化胰蛋白酶整体小柱的制备及其用于微量蛋白质的快速酶解

发展了一种光引发聚合法制备固定化胰蛋白酶整体小柱的方法,以用于微量蛋白质的快速酶解。整体小柱由功能单体4-戊烯酸琥珀酰亚胺酯、甲基丙烯酸羟乙酯,交联剂季戊四醇三丙烯酸酯和三元致孔剂二甲基亚砜、N,N-二甲基甲酰胺、十二醇在20 μL的移液器吸头尖端原位聚合而成。形成整体柱后,胰蛋白酶分子通过氨基与琥珀酰亚胺酯反应实现固定化。系统研究了聚合溶液中活性酯含量与柱床体积对胰蛋白酶固载量的影响,评价了固定化酶整体小柱对标准蛋白细胞色素C和牛血清白蛋白的酶解效率,以及整体小柱的稳定性和重复性。结果表明,在离心辅助下,酶解过程可在10 min内完成,批次间具有良好的重复性。最后将固定化酶整体小柱应用于1×10⁵个人急性早幼粒白血病（NB4）细胞与人急性T细胞白血病（Jurkat T）细胞的快速酶解,经纳升级液相色谱与高分辨质谱联用分析后鉴定得到2489个和2572个蛋白质。相比于溶液状态下的酶解,分别提高了2.2%和6.1%的蛋白鉴定数量,展现了其在蛋白组学研究中的应用潜力。     

Capillary electrochromatography with monolithic stationary phases. II. Preparation of cationic stearyl-acrylate monoliths and their electrochromatographic characterization

A novel cationic monolithic stationary phase based on the co-polymerization of pentaerythritol diacrylate monostearate (PEDAS) with a selected quaternary amine acrylic monomer was designed for performing capillary electrochromatography at high flow velocity. While PEDAS functioned as both the ligand provider and the cross-linker, the quaternary amine acrylic monomer was introduced to control the magnitude of the electroosmotic flow (EOF). The fabrication of the cationic stearyl-acrylate monolith (designated as cationic C17 monolith) with controlled porosity was achieved by free radical polymerization using the initiator 2,2'-azobisisobutyronitrile in the presence of a ternary porogenic solvent composed of cyclohexanol, ethylene glycol and water. Four different quaternary amine acrylic monomers were investigated in order to find the optimum monomer for achieving maximum electroosmotic flow (EOF) velocity. Both photo- and thermally-initiated polymerization proved effective in producing the cationic C17 monolith, and the best monolith was achieved when [2-(acryloyloxy)ethyl]trimethyl ammonium methyl sulfate (AETA) was used as the quaternary amine acrylic monomer. Although the zeta potential of the resulting cationic C17 monolith is positive with respect to water, the magnitude and direction of the EOF was markedly affected by the nature of the electrolyte in the mobile phase. Consequently, anodal, zero or cathodal EOF was observed depending on the nature of the electrolyte, and this was attributed to the adsorption of the ionic components of the electrolyte on to the solid stationary phase, which is characterized by its amphiphilic nature consisting of C17 chains, ester functions, hydroxyl groups and quaternary amine moieties. Optimized PEDAS-AETA monoliths yielded columns with high separation efficiency and allowed rapid separations on the time scale of seconds to be achieved with short capillaries.     

Preparation and evaluation of hydrophilic C18 monolithic sorbents for enhanced polar compound retention in liquid chromatography and solid phase extraction

Hydrophilic C18 monolithic polymer sorbents were synthesized for use in solid phase extraction (SPE) and in capillary liquid chromatography (LC). The approach involved incorporating both hydrophobic and hydrophilic monomers into a monolithic material, by copolymerization of stearyl methacrylate (SMA), poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) and ethylene dimethacrylate (EDMA) in the presence of selected porogens, to produce translucent mesoporous monolithic materials in bulk (SPE) or white macroporous monoliths inside fused silica capillary columns (capillary LC). A capillary column containing one of the hydrophilic C18 monoliths (i.e. poly(SMA-co-PEGMEMA-co-EDMA) with 15% (w/w) PEGMEMA) demonstrated nearly 35% reduction in retention of polycyclic aromatic compounds and greater than 40% increase in retention of phenols compared to a hydrophobic C18 monolithic column. In addition, the hydrophilic monolith demonstrated significantly improved resolution of phenols. Similar monolithic materials prepared in bulk were ground and sieved to obtain 45-65 μm particles with desired rigidity for SPE. To achieve optimum extraction performance for phenols, several parameters, including sample pH and volume, and eluent type and volume, were investigated. Under optimized experimental conditions, the method demonstrated good sensitivity (1.6 ng/mL LOD) and linearity (R(2)>0.97 for 10-200 ng/mL). Again, incorporation of 15% (w/w) PEGMEMA in the monolith increased the extraction efficiency of phenols in water from approximately 20% to 67-92% compared to a hydrophobic C18 monolithic material. Increased wettability of the sorbent by the aqueous sample matrix and the presence of hydrogen-bonding interactions are responsible for the improved retention of polar compounds.     

Facile preparation of a polydopamine‐based monolith for multiple monolithic fiber solid‐phase microextraction of triazine herbicides in environmental water samples

A new multiple monolithic fiber solid‐phase microextraction using a polydopamine‐based monolith as the extraction medium is proposed. The monolith was synthesized by facile in situ copolymerization of N‐methacryldopamine and dual cross‐linkers (divinylbenzene/ethylenedimethacrylate) in the presence of N ,N‐dimethylformamide. The effect of the contents of N‐methacryldopamine and porogen in the polymerization mixture on the extraction performance was investigated thoroughly. A series of characterization studies was performed to validate the structure and properties of the monolith. The prepared multiple monolithic fibers were used for the extraction of triazine herbicides in environmental water samples. After the optimization of the extraction parameters, a convenient, sensitive, cost‐effective, and environmentally friendly method for the determination of trace triazine herbicides in water samples was developed by coupling multiple monolithic fibers solid‐phase microextraction with high‐performance liquid chromatography and diode array detection. The results indicated that the limits of detection and quantification for the target compounds were 0.031–0.14 and 0.10–0.45 μg/L, respectively. Good precision and reproducibility were obtained with the relative standard deviations below 10%. The developed method was applied to the analysis of the triazine herbicides in different water samples (lake, river, and farmland waters). The recoveries of the method were in the range between 79.6 and 117%.     

Hydrophilic monolith based immobilized enzyme reactors in capillary and on microchip for high-throughput proteomic analysis

A novel kind of hydrophilic monolith based immobilized enzyme reactors (IMERs) was prepared both in UV-transparent capillaries and on glass microchips by the photopolymerization of N-acryloxysuccinimide and poly(ethylene glycol)diacrylate, followed by trypsin immobilization. The performance of capillary IMERs for protein digestion was evaluated by the digestion of myoglobin with the residential time from 12s to 71 s. With μRPLC-ESI-MS/MS analysis, the obtained sequence coverages were all over 80%, comparable to that obtained by in-solution digestion for 12 h. The nonspecific absorption of BSA on monolithic support was evaluated, and no obvious protein residue was observed by a fluorescence assay. Moreover, no carry-over of the digests on the capillary IMER was found after the digestion of myoglobin (24 μg) and BSA (9 μg), which further demonstrated the good hydrophilicity of such matrix. In addition, an integrated microchip-based system involving on-line protein digestion by microchip-based IMER, peptides separation by nanoRPLC and identification by ESI-MS/MS was established, by which a mixture of standard proteins and one RPLC fraction of Escherichia coli extract were successfully identified, indicating that the hydrophilic monolith based IMER might provide a promising tool for high-throughput proteomic analysis.     

金纳米粒子修饰聚合物固相微萃取整体柱的制备及其性能研究

通过在毛细管聚合物整体柱表面修饰金纳米粒子,制备了一种可选择性捕获含巯基化合物的固相微萃取整体柱.首先制备聚(甲基丙烯酸缩水甘油酯-乙二醇二甲基丙烯酸酯)整体柱,在其表面化学修饰半胱胺;通过半胱胺上的巯基基团将金纳米粒子固定在整体柱的孔表面.以巯基类化合物为探针,评价了固相微萃取整体柱的萃取性能.结果表明,由于Au对巯...     

Characterization of a monolithic immobilized trypsin microreactor with on-line coupling to ESI-MS

The preparation and characterization of a miniaturized trypsin reactor using on-line coupling with an ESI-TOF mass spectrometer are described. L-1-Tosylamido-2-phenylethyl chloromethyl ketone-trypsin was covalently immobilized on poly(glycidyl methacrylate-co-ethylene dimethacrylate) monolith prepared in a 75 microm ID fused silica capillary resulting in a bioreactor with high local concentration of the proteolytic enzyme. Covalent immobilization of trypsin on this support was performed using the epoxide functional groups in either a one- or a multistep reaction. For on-line protein digestion-MS analysis the bioreactor was coupled with the mass spectrometer using a liquid junction microelectrospray interface. The performance of the reactor was tested using an on-line flow through the system with flow rates of 50-300 nL/min. The resulting protein consumption was in the atto- to low femtomole range. Proteolytic activity was characterized in a wide range of conditions with respect to the flow rate, pH, and temperature. Complete protein digestion was achieved in less than 30 s at 25 degrees C with the sequence coverage of 80% (cytochrome c), which is comparable to 3 h digestion in solution at 37 degrees C. Besides the good performance at laboratory temperature, the immobilized trypsin in the bioreactor also performed well at lower pH compared to the standard in-solution protocols.     

Preparation and evaluation of a macroporous molecularly imprinted hybrid silica monolithic column for recognition of proteins by high performance liquid chromatography

A novel type of macroporous molecularly imprinted hybrid silica monolithic column was first developed for recognition of proteins. The macroporous silica-based monolithic skeleton was synthesized in a 4.6 mm i.d. stainless steel column by a mild sol–gel process with methyltrimethoxysilane (MTMS) as a sole precursor, and then vinyl groups were introduced onto the surface of the silica skeleton by chemical modification of γ-methacryloxypropyltrimethoxysilane (γ-MAPS). Subsequently, the molecularly imprinted polymer (MIP) coating was copolymerized and anchored onto the surface of the silica monolith. Bovine serum albumin (BSA) and lysozyme (Lyz), which differ greatly in molecular size, isoelectric point, and charge, were representatively selected for imprinted templates to evaluate recognition property of the hybrid silica-based MIP monolith. Some important factors, such as template–monomer molar ratio, total monomer concentration and crosslinking density, were systematically investigated. Under the optimum conditions, the obtained hybrid silica-based MIP monolith showed higher binding affinity for template than its corresponding non-imprinted (NIP) monolith. The imprinted factor (IF) for BSA and Lyz reached 9.07 and 6.52, respectively. Moreover, the hybrid silica-based MIP monolith displayed favorable binding characteristics for template over competitive protein. Compared with the imprinted silica beads for stationary phase and in situ organic polymer-based hydrogel MIP monolith, the hybrid silica MIP monolith exhibited higher recognition, stability and lifetime.     

Poly(methacrylic acid-ethylene glycol dimethacrylate) monolith in-tube solid phase microextraction coupled to high performance liquid chromatography and analysis of amphetamines in urine samples

In-tube solid-phase microextraction (SPME) based on a poly(methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary column was investigated for the extraction of amphetamine, methamphetamine and their methylenedioxy derivatives. The monolithic capillary column showed high extraction efficiency towards target analytes, which could be attributed to its larger loading amount of extraction phase than conventional open-tubular extraction capillaries and the convective mass transfer procedure provided by its monolithic structure. The extraction mechanism was studied, and the results indicated that the extraction process of the target analytes was involved with hydrophobic interaction and ion-exchange interaction. The polymer monolith in-tube SPME-HPLC system with UV detection was successfully applied to the determination of amphetamine, methamphetamine and their methylenedioxy derivatives in urine samples, yielding the detection limits of 1.4 - 4.0 ng/mL. Excellent method reproducibility (RSD < 2.9%) was found over a linear range of 0.05-5 microg/mL, and the time for the whole analysis was only approximately 25 min. The monolithic capillary column was reusable in coping with the complicated urine samples.