Air‐Stable Lithium Spheres Produced by Electrochemical Plating

Lithium metal is an ideal anode for next‐generation lithium batteries owing to its very high theoretical specific capacity of 3860 mAh g^?1 but very reactive upon exposure to ambient air, rendering it difficult to handle and transport. Air‐stable lithium spheres (ASLSs) were produced by electrochemical plating under CO₂ atmosphere inside an advanced aberration‐corrected environmental transmission electron microscope. The ASLSs exhibit a core–shell structure with a Li core and a Li₂CO₃ shell. In ambient air, the ASLSs do not react with moisture and maintain their core–shell structures. Furthermore, the ASLSs can be used as anodes in lithium‐ion batteries, and they exhibit similar electrochemical behavior to metallic Li, indicating that the surface Li₂CO₃ layer is a good Li⁺ ion conductor. The air stability of the ASLSs is attributed to the surface Li₂CO₃ layer, which is barely soluble in water and does not react with oxygen and nitrogen in air at room temperature, thus passivating the Li core.     

Studies on the effects of coated Li2CO3 on lithium electrode

Although a lithium metal anode has a high energy density compared with a carbon insertion anode, the poor rechargeability prevents the practical use of anode materials. A lithium electrode coated with Li₂CO₃ was prepared as a negative electrode to enhance cycleability through the control of the solid electrolyte interface (SEI) layer formation in Li secondary batteries. The electrochemical characteristics of the SEI layer were examined using chronopotentiometry (CP) and impedance spectroscopy. The Li₂CO₃-SEI layer prevents electrolyte decomposition reaction and has low interface resistance. In addition, the lithium ion diffusion in the SEI layer of the uncoated and the Li₂CO₃-coated electrode was evaluated using chronoamperometry (CA).     

XPS study of the Li intercalation process in sol–gel‐produced V2O5 thin film: influence of substrate and film synthesis modification

We report on the process of lithium intercalation in V₂O₅ thin films deposited onto standard ITO‐coated glass substrates. The films were deposited via a well‐established sol–gel route, and the samples were examined as working electrodes in a range of potentials versus lithium reference electrode. This paper follows up issues arising from parallel spectroscopic characterizations of the films by X‐ray photoelectron spectroscopy (XPS). Specifically, the XPS examination showed that not all of the Li‐ion charge inserted was accounted for by the V(5) to V(4) reduction, but the stoichiometric balance could be maintained only by considering additional oxygens arising from the intercalation procedure, leading to Li₂O formation. In this work, we have examined the possibility that the source of oxygen is the ITO substrate. To this purpose, films of V₂O₅ deposited on silicon substrates have been prepared using the sol–gel process and examined by XPS after electrochemical intercalation/de‐intercalation cycles. We show that in this case a perfect balance between electrochemical charge, inserted Li and reduced vanadium is obtained. A further indication of ITO‐substrate effects was obtained from examination, by the same methods, of some unconventional V₂O₅ films that had been co‐precipitated with a siloxane, designed to provide a template structure. The results obtained from this material imply that a barrier layer is formed at the ITO interface and, therefore, the formation of Li₂O is avoided. The results are discussed in terms of the possible degradation of conventional V₂O₅ on ITO as a result of electrochemically induced interface reactions. Copyright © 2005 John Wiley & Sons, Ltd.     

Three‐Dimensional Fe2N@C Microspheres Grown on Reduced Graphite Oxide for Lithium‐Ion Batteries and the Li Storage Mechanism

Nanostructured iron compounds as lithium‐ion‐battery anode material have attracted considerable attention with respect to improved electrochemical energy storage and excellent specific capacity, so lots of iron‐based composites have been developed. Herein, a novel composite composed of three‐dimensional Fe₂N@C microspheres grown on reduced graphite oxide (denoted as Fe₂N@C‐RGO) has been synthesized through a simple and effective technique assisted by a hydrothermal and subsequent heating treatment process. As the anode material for lithium‐ion batteries, the synthetic Fe₂N@C‐RGO displayed excellent Li⁺‐ion storage performance with a considerable initial capacity of 847 mAh g^?1, a superior cycle stability (a specific discharge capacity of 760 mAh g^?1 remained after the 100th cycle), and an improved rate‐capability performance compared with those of the pure Fe₂N and Fe₂N‐RGO nanostructures. The good performance should be attributed to the existence of RGO layers that can facilitate to enhance the conductivity and shorten the lithium‐ion diffusion path; in addition, the carbon layer on the surface of Fe₂N can avert the structure decay caused by the volume change during the lithiation/delithiation process. Moreover, in situ X‐ray absorption fine‐structure analysis demonstrated that the excellent performance can be attributed to the lack of any obvious change in the coordination geometry of Fe₂N@C‐RGO during the charge/discharge processes.     

Fast Lithium Ion Conduction in Lithium Phosphidoaluminates

Solid electrolyte materials are crucial for the development of high‐energy‐density all‐solid‐state batteries (ASSB) using a nonflammable electrolyte. In order to retain a low lithium‐ion transfer resistance, fast lithium ion conducting solid electrolytes are required. We report on the novel superionic conductor Li₉AlP₄ which is easily synthesised from the elements via ball‐milling and subsequent annealing at moderate temperatures and which is characterized by single‐crystal and powder X‐ray diffraction. This representative of the novel compound class of lithium phosphidoaluminates has, as an undoped material, a remarkable fast ionic conductivity of 3 mS cm^?1 and a low activation energy of 29 kJ mol^?1 as determined by impedance spectroscopy. Temperature‐dependent ⁷Li NMR spectroscopy supports the fast lithium motion. In addition, Li₉AlP₄ combines a very high lithium content with a very low theoretical density of 1.703 g cm^?3. The distribution of the Li atoms over the diverse crystallographic positions between the [AlP₄]^9? tetrahedra is analyzed by means of DFT calculations.     

Simultaneous Carbon Coating and Lithiation of Oxides by Contact Reaction

Chemical lithiation and carbon coating of cathode materials can lead to strongly improved electrochemical properties, especially if the active materials have low electronic conductivity. This behavior is quite often the case for new high‐capacity materials. A novel synthesis method is presented in which the two processes are performed simultaneously by employing Li₂C₂ as both the carbon and the lithium source. In this contact reaction, the acetylide anion C₂^2? is oxidized to carbon and deposited directly on the surface of the active material, while lithium is reductively inserted into the oxidant. Two different synthesis routes are demonstrated: a tribochemical approach at room temperature and heat treatments between 150 and 600 °C. The applicability of these new carbon‐coating methods are demonstrated on various crystalline and amorphous Li_xV₂O₅ phases. The composites obtained were characterized by powder X‐ray diffraction, transmission electron microscopy, and Raman spectroscopy. In addition, electrochemical data confirm the chemical lithiation and show that lithiated Li_xV₂O₅ with specific phases can be prepared selectively.     

Surface film formation on a graphite electrode in Li‐ion batteries: AFM and XPS study

The formation of a passivation film (solid electrolyte interphase, SEI) at the surface of the negative electrode of full LiCoO₂/graphite lithium‐ion cells using LiPF₆ (1M ) in carbonate solvents as electrolyte was investigated by means of x‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The analyses were carried out at different potentials of the first and the fifth cycles, showing the potential‐dependent character of the surface‐film species formation. These species were mainly identified as Li₂CO₃ up to 3.8 V and LiF up to 4.2 V. This study shows the formation of the SEI during charging and its partial dissolution during discharge. Copyright © 2005 John Wiley & Sons, Ltd.     

Constructing Co3O4 Nanowires on Carbon Fiber Film as a Lithiophilic Host for Stable Lithium Metal Anodes

Lithium metal has been considered as the most promising anode electrode for substantially improving the energy density of next‐generation energy storage devices. However, uncontrollable lithium dendrite growth, an unstable solid electrolyte interface (SEI), and infinite volume variation severely shortens its service lifespan and causes safety hazards, thus hindering the practical application of lithium metal electrodes. Here, carbon fiber film (CFF) modified by lithiophilic Co₃O₄ nanowires (denoted as Co₃O₄ Nws) was proposed as a matrix for prestoring lithium metal through a thermal infusion method. The homogeneous needle‐like Co₃O₄ nanowires can effectively promote molten lithium to infiltrate into the CFF skeleton. The post‐formed Co?Li₂O nanowires produced by the reaction of Co₃O₄ Nws and molten lithium can homogeneously distribute lithium ions flux and efficaciously increase the adsorption energy with lithium ions proved by density functional theory (DFT) calculation, boosting a uniform lithium deposition without dendrite growth. Therefore, the obtained composite anode (denoted as CFF/Co?Li₂O@Li) exhibits superior electrochemical performance with high stripping/plating capacities of 3 mAh cm^?2 and 5 mAh cm^?2 over long‐term cycles in symmetrical batteries. Moreover, in comparison with bare lithium anode, superior Coulombic efficiencies coupled with copper collector and full battery behaviors paired with LiFePO₄ cathode are achieved when CFF/Co?Li₂O@Li composite anode was employed.     

A Liquid/Liquid Electrolyte Interface that Inhibits Corrosion and Dendrite Growth of Lithium in Lithium‐Metal Batteries

A proof‐of‐concept study on a liquid/liquid (L/L) two‐phase electrolyte interface is reported by using the polarity difference of solvent for the protection of Li‐metal anode with long‐term operation over 2000 h. The L/L electrolyte interface constructed by non‐polar fluorosilicane (PFTOS) and conventionally polar dimethyl sulfoxide solvents can block direct contact between conventional electrolyte and Li anode, and consequently their side reactions can be significantly eliminated. Moreover, the homogeneous Li‐ion flow and Li‐mass deposition can be realized by the formation of a thin and uniform solid‐electrolyte interphase (SEI) composed of LiF, Li_xC, Li_xSiO_y between PFTOS and Li anode, as well as the super‐wettability state of PFTOS to Li anode, resulting in the suppression of Li dendrite formation. The cycling stability in a lithium–oxygen battery as a model is improved 4 times with the L/L electrolyte interface.     

Processable and Moldable Sodium‐Metal Anodes

Sodium‐ion batteries are similar in concept and function to lithium‐ion batteries, but their development and commercialization lag far behind. One obstacle is the lack of a standard reference electrode. Unlike Li foil reference electrodes, sodium is not easily processable or moldable and it deforms easily. Herein we fabricate a processable and moldable composite Na metal anode made from Na and reduced graphene oxide (r‐GO). With only 4.5 % percent r‐GO, the composite anodes had improved hardness, strength, and stability to corrosion compared to Na metal, and can be engineered to various shapes and sizes. The plating/stripping cycling of the composite anode was significantly extended in both ether and carbonate electrolytes giving less dendrite formation. We used the composite anode in both Na‐O₂ and Na‐Na₃V₂(PO₄)₃ full cells.     

Elucidating the Beneficial Effect of Vinylene Carbonate on the Electrochemistry of Antimony Electrodes in Lithium Batteries

Vinylene carbonate (VC) is an effective electrolyte additive for improving electrode performance in lithium‐ion batteries. We confirm its beneficial effects in a nanosized Sb–cellulose fiber composite electrode and examine its mechanism of action by X‐ray photoelectron spectroscopy, the most suitable technique for characterizing active particle surfaces (especially electrode/electrolyte interfaces). Vinylene carbonate clearly increases electrolyte stability (particularly that of LiPF₆) by avoiding the formation of a thick layer of LiF that conceals Sb and prevents its reaction with Li. Decreasing the layer thickness therefore increases the reversibility of the electrochemical reaction and improves capacity retention on cycling. The presence of VC afforded high‐quality Sb 4d and Li 1s photoemissions, fitting of which clearly exposed a previously unreported low‐energy component. We believe that this component is an Li_xSb alloy, which for the first time is identified spectroscopically.     

Li4Ti5O12 Nanoparticles Prepared with Gel-hydrothermal Process as a High Performance Anode Material for Li-ion Batteries

Li₄Ti₅O₁₂ (LTO) nanoparticles were prepared by gel‐hydrothermal process and subsequent calcination treatment. Calcination treatment led to structural water removal, decomposition of organics and primary formation of LTO. The formation temperature of spinel LTO nanoparticles was lower than that of bulk materials counterpart prepared by solid‐state reaction or by sol‐gel processing. Based on the thermal gravimetric analysis (TG) and differential thermal gravimetric (DTG), samples calcined at different temperatures (350, 500 and 700°C) were characterized by X‐ray diffraction (XRD), field emitting scanning electron microscopy (FESEM), transmission electron microscopy (TEM), cyclic voltammogram and charge‐discharge cycling tests. A phase transition during the calcination process was observed from the XRD patterns. And the sample calcined at 500°C had a distribution of diameters around 20 nm and exhibited large capacity and good high rate capability. The well reversible cyclic voltammetric results of both electrodes indicated enhanced electrochemical kinetics for lithium insertion. It was found that the Li₄Ti₅O₁₂ anode material prepared through gel‐hydrothermal process, when being cycled at 8 C, could preserve 76.6% of the capacity at 0.3 C. Meanwhile, the discharge capacity can reach up to 160.3 mAh·g^?1 even after 100 cycles at 1 C, close to the theoretical capacity of 175 mAh·g^?1. The gel‐hydrothermal method seemed to be a promising method to synthesize LTO nanoparticles with good application in lithium ion batteries and electrochemical cells.     

Characterization of a Multicomponent Lithium Lithiate from a Combined X‐Ray Diffraction,NMR Spectroscopy,and Computational Approach

An unusual lithium lithiate [Li(diglyme)₂][(diglyme)Li₂(C₄H₃S)₃], made up from three carbanions, two lithium cations, and a single donor base molecule in the anion and a single lithium cation, coordinated by two donor base molecules, is investigated in a combined study including X‐ray diffraction, NMR spectroscopy and computational approaches in solution and the solid state. While the multicomponent lithiate is the only species present in the solid state, solution NMR spectroscopy and computational methods were employed to identify a second species in solution. The dimer [(diglyme)Li(C₄H₃S)]₂ coexists with the lithiate in solution in a 1:1 ratio, the more the higher the polarity of the solvent is. Only the combination of this multitude of methods provides a firm picture of the whole.     

Structure and lithium dynamics of Li2AuSn2--a ternary stannide with condensed AuSn4/2 tetrahedra

The new stannide Li₂AuSn₂ was prepared by reaction of the elements in a sealed tantalum tube in a resistance furnace at 970 K followed by annealing at 720 K for five days. Li₂AuSn₂ was investigated by X‐ray diffraction on powders and single crystals and the structure was refined from single‐crystal data: Z=4, I4₁/amd, a=455.60(7), c=1957.4(4) pm, wR2=0.0681, 278 F² values, 10 parameters. The gold atoms display a slightly distorted tetrahedral tin coordination with Au? Sn distances of 273 pm. These tetrahedra are condensed through common corners leading to the formation of two‐dimensional AuSn_4/2 layers. The latter are connected in the third dimension through Sn? Sn bonds (296 pm). The lithium atoms fill distorted hexagonal channels formed by the three‐dimensional [AuSn₂] network. Modestly small ⁷Li Knight shifts are measured by solid‐state NMR spectroscopy that are consistent with a nearly complete state of lithium ionization. The noncubic local symmetry at the tin site is reflected by a nuclear electric quadrupolar splitting in the ¹¹⁹Sn Mössbauer spectra and a small chemical shift anisotropy evident from ¹¹⁹Sn solid‐state NMR spectroscopy. Variable‐temperature static ⁷Li solid‐state NMR spectra reveal motional narrowing effects at temperatures above 200 K, revealing lithium atomic mobility on the kHz time scale. Detailed lineshape as well as temperature‐dependent spin lattice relaxation time measurements indicate an activation energy of lithium motion of 27 kJ mol^?1.     

Preparation of Li4Ti5O12 Yolk–Shell Powders by Spray Pyrolysis and their Electrochemical Properties

We have reported for the first time the preparation of yolk–shell‐structured Li₄Ti₅O₁₂ powders for use as anode materials in lithium‐ion batteries. One Li₄Ti₅O₁₂ yolk–shell‐particle powder is directly formed from each droplet containing lithium, titanium, and carbon components inside the hot wall reactor maintained at 900 °C. The precursor Li₄Ti₅O₁₂ yolk–shell‐particle powders, which are directly prepared by spray pyrolysis, have initial discharge and charge capacities of 155 and 122 mA h g^?1, respectively, at a current density of 175 mA g^?1. Post‐treatment of the yolk–shell‐particle powders at temperatures of 700 and 800 °C improves the initial discharge and charge capacities. The initial discharge capacities of the Li₄Ti₅O₁₂ powders with a yolk–shell structure and a dense structure post‐treated at 800 °C are 189 and 168 mA h g^?1, respectively. After 100 cycles, the corresponding capacities are 172 and 152 mA h g^?1, respectively (retentions of 91 and 90 %).     

Stabilizing Lithium Plating by a Biphasic Surface Layer Formed In Situ

The dendritic growth of Li metal leads to electrode degradation and safety concerns, impeding its application in building high energy density batteries. Forming a protective layer on the Li surface that is electron‐insulating, ion‐conducting, and maintains an intimate interface is critical. We herein demonstrate that Li plating is stabilized by a biphasic surface layer composed of a lithium‐indium alloy and a lithium halide, formed in situ by the reaction of an electrolyte additive with Li metal. This stabilization is attributed to the fast lithium migration though the alloy bulk and lithium halide surface, which is enabled by the electric field across the layer that is established owing to the electron‐insulating halide phase. A greatly stabilized Li‐electrolyte interface and dendrite‐free plating over 400 hours in Li|Li symmetric cells using an alkyl carbonate electrolyte is demonstrated. High energy efficiency operation of the Li₄Ti₅O₁₂ (LTO)|Li cell over 1000 cycles is achieved.     

Electrophoretic Deposition of Binder‐Free MnO2/Graphene Films for Lithium‐Ion Batteries

Binder‐free, nano‐sized needlelike MnO₂ ‐submillimeter‐sized reduced graphene oxide (nMnO₂‐srGO ) hybrid films with abundant porous structures were fabricated through electrophoretic deposition and subsequent thermal annealing at 500 °C for 2 h. The as‐prepared hybrid films exhibit a unique hierarchical morphology, in which nMnO₂ with a diameter of 20—50 nm and a length of 300—500 nm is randomly anchored on both sides of srGO . When evaluated as binder‐free anodes for lithium‐ion half‐cell, the nMnO₂‐srGO composites with a content of 76.9 wt% MnO₂ deliver a high capacity of approximately 1652.2 mA •h•g⁻¹ at a current density of 0.1 A•g⁻¹ after 200 cycles. The high capacity remains at 616.8 mA •h•g⁻¹ (ca. 65.1% capacity retention) at a current density as high as 4 A•g⁻¹. The excellent electrochemical performance indicates that the nMnO₂‐srGO hybrid films could be a promising anode material for lithium ion batteries (LIBs ).     

Lithium Argyrodites with Phosphorus and Arsenic: Order and Disorder of Lithium Atoms,Crystal Chemistry,and Phase Transitions

Crystal chemical data of high‐ (HT) and low‐temperature (LT) modifications of lithium argyrodites with the compositions Li₇PCh₆ (Ch=S, Se), Li₆PCh₅X (X=Cl, Br, I), Li₆AsS₅Br, and Li₆AsCh₅I (Ch=S, Se) based on single‐crystal, powder X‐ray (113 K<T<503 K) and neutron measurements (5 K<T<293 K) are presented. In the HT modifications, the Li atoms are strongly disordered over a fraction of the available tetrahedral holes, whereas in the LT modifications they occupy ordered crystallographic positions with a pronounced site preference that is analysed on a crystal chemical basis. The Ch/X partial structures remain nearly unchanged upon the reversible phase transitions. Crystal chemical and crystallographic relations between HT and LT modifications based on the Frank–Kasper model of tetrahedral close packing are discussed. X‐ray single‐crystal data for HT‐Li₆PS₅I show the electron density of the disordered Li to be smeared out over an extended region preferably inside face‐sharing double tetrahedra. A series of temperature‐dependent powder neutron data for Li₆PS₅I gives clear evidence for an HT/LT phase transition at ≈175 K with an ordering of the Li atoms in different polyhedra with coordination numbers between three and four.     

Molybdenum Substitution for Improving the Charge Compensation and Activity of Li2MnO3

Lithium‐rich layer‐structured oxides xLi₂MnO₃? (1?x)LiMO₂ (0<x<1, M=Mn, Ni, Co, etc.) are interesting and potential cathode materials for high energy‐density lithium ion batteries. However, the characteristic charge compensation contributed by O^2? in Li₂MnO₃ leads to the evolution of oxygen during the initial Li⁺ ion extraction at high voltage and voltage fading in subsequent cycling, resulting in a safety hazard and poor cycling performance of the battery. Molybdenum substitution was performed in this work to provide another electron donor and to enhance the electrochemical activity of Li₂MnO₃‐based cathode materials. X‐ray diffraction and adsorption studies indicated that Mo⁵⁺ substitution expands the unit cell in the crystal lattice and weakens the Li?O and Mn?O bonds, as well as enhancing the activity of Li₂MnO₃ by lowering its delithiation potential and suppressing the release of oxygen. In addition, the chemical environment of O^2? ions in molybdenum‐substituted Li₂MnO₃ is more reversible than in the unsubstituted sample during cycling. Therefore molybdenum substitution is expected to improve the performances of the Li₂MnO₃‐based lithium‐rich cathode materials.     

Cu3V2O8 Nanoparticles as Intercalation‐Type Anode Material for Lithium‐Ion Batteries

Cu₃V₂O₈ nanoparticles with particle sizes of 40–50 nm have been prepared by the co‐precipitation method. The Cu₃V₂O₈ electrode delivers a discharge capacity of 462 mA h g^?1 for the first 10 cycles and then the specific capacity, surprisingly, increases to 773 mA h g^?1 after 50 cycles, possibly as a result of extra lithium interfacial storage through the reversible formation/decomposition of a solid electrolyte interface (SEI) film. In addition, the electrode shows good rate capability with discharge capacities of 218 mA h g^?1 under current densities of 1000 mA g^?1. Moreover, the lithium storage mechanism for Cu₃V₂O₈ nanoparticles is explained on the basis of ex situ X‐ray diffraction data and high‐resolution transmission electron microscopy analyses at different charge/discharge depths. It was evidenced that Cu₃V₂O₈ decomposes into copper metal and Li₃VO₄ on being initially discharged to 0.01 V, and the Li₃VO₄ is then likely to act as the host for lithium ions in subsequent cycles by means of the intercalation mechanism. Such an “in situ” compositing phenomenon during the electrochemical processes is novel and provides a very useful insight into the design of new anode materials for application in lithium‐ion batteries.