NiO/Al_2O_3催化剂上二氧化碳气氛下异丁烷耦合脱氢制异丁烯

研究了二氧化碳气氛下NiO/Al2O3催化剂上异丁烷脱氢制异丁烯的反应性能,考察了助剂K2O对NiO/Al2O3催化性能的影响。结果表明,与在惰性气氛下的反应相比,在二氧化碳气氛下异丁烷脱氢与逆水煤气变换反应耦合,促进了异丁烷脱氢反应,异丁烯的收率得到提高。助剂K2O的加入,能降低催化剂的酸性,减缓反应过程中催化活性物种NiO的过度还原,并抑制异丁烷裂解及积炭生成等副反应,从而提高了异丁烯的收率以及催化剂的稳定性。     

异丁烷脱氢V2O5/γ-Al2O3催化剂的研究

五氧化二钒;异丁烷脱氢V2O5/γ-Al2O3催化剂的研究     

镧对V2O5/γ-Al2O3催化剂在异丁烷脱氢中活性的影响

V2O5／γ-Al2O3是用于异丁烷脱氢的新型催化剂，引入适量的镧不仅可改善活性组分的分散度，提高催化脱氢活性，而且还增强了催化剂的抗积炭能力，通过FTIR，BET，TG，TPR和TEM等手段研究了镧对催化剂性能的影响。     

V2O5/γ-Al2O3和V2O5/SiO2负载型催化剂对异丁烷的催化脱氢性能

V2O5/γ-Al2O3和V2O5/SiO2负载型催化剂对异丁烷的催化脱氢性能;V2O5/γ-Al2O3; V2O5/SiO2; 异丁烷; 脱氢     

异丁烷在Pt-Sn-K/Al2O3上的脱氢反应

负载催化剂;异丁烷在Pt-Sn-K/Al2O3上的脱氢反应     

氧化铝载体对Pt-Sn-K/γ-Al2O3催化剂上异丁烷脱氢性能的影响

采用盐酸回流法和氨水沉淀法合成了氧化铝载体,并通过络合真空浸渍法制备了不同来源氧化铝负载的Pt-Sn-K/γ-Al₂O₃催化剂。利用N₂物理吸附、CO脉冲吸附、H₂程序升温还原、NH₃程序升温脱附、热重等手段对Pt-Sn-K/γ-Al₂O₃催化剂进行了表征,以异丁烷脱氢为探针反应研究了氧化铝载体对该催化剂脱氢性能的影响。结果表明,与由盐酸回流法合成的载体制备的催化剂相比,采用氨水沉淀法合成的氧化铝载体制备的Pt-Sn-K/γ-Al₂O₃催化剂表面具有较小的Pt颗粒和较弱的酸性分布,其脱氢活性及异丁烯选择性更优。14 d的连续运行数据显示,由氨水沉淀合成的载体制备的催化剂,其抗积炭能力更强,反应后催化剂的积炭石墨化程度更低,因而具有更好的稳定性;在该催化剂上,异丁烷初始转化率为56.67%,14 d后仍能达到34.71%,异丁烯初始选择性为80%,7 d后维持在94%左右。     

异丁烷脱氢催化剂的研究

本文对异丁烷脱氢反应制异丁烯过程催化剂体系及其反应机理进行了述评,指出异丁烷脱氢依然是最有潜力的转化途径,但非贵金属高效催化剂的研制是其关键.详细总 结了不同载体和助剂对脱氢反应的影响,尤其是载体和助剂的酸碱性以及载体的孔结构.弱 酸中心有利于异丁烷脱氢反应的发生,较小的孔结构能提高反应的选择性.催化剂的抗积炭 性能研究表明: 载体表面的弱酸位和活性组分在表面的高分散度以及碱性助剂的加入,有 利于提高催化剂的抗积炭性能.对异丁烷的脱氢反应机理的研究进行了阐述.     

Cr对Pt-Sn/γ-Al2O3催化剂丙烷脱氢性能的影响

通过H2-TPR、O2-脉冲等表征手段,结合丙烷脱氢催化性能考察了助剂Cr对Pt-Sn/γ-Al2O3催化剂反应性能的影响。结果表明,添加少量Cr可显著改善Pt-Sn/γ-Al2O3催化剂的脱氢稳定性,可提高丙烯选择性,降低催化剂表面积炭量。这是由Cr和Pt-Sn之间存在的协同作用引起的,一方面,Pt促进了Cr的还原,生成了可提高丙烯选择性的+3价Cr;另一方面,Cr使Sn变得难于还原,在强还原气氛下保持了活性氧化态价态,进而改善了催化剂的脱氢稳定性。     

负载型Pt/CeO_2-Al_2O_3催化剂的制备及其脱氢性能

通过超声辅助共沉淀法制备了具有高比表面积、大孔容和大孔径的CeO_2-Al_2O_3复合载体,并以此制备了一系列负载型Pt/CeO_2-Al_2O_3催化剂,采用XRD、氮吸附、NH3-TPD、SEM和TEM等方法对复合载体和催化剂进行了表征;以甲基环己烷为模型化合物,考察了Pt/CeO_2-Al_2O_3催化剂的脱氢性能,研究了载体中Ce/Al物质的量比及反应温度对其催化脱氢性能的影响。结果表明,当Ce/Al物质的量比为0.5时,Pt/CeO_2-Al_2O_3催化剂在450℃下具有较高的脱氢性能;甲基环己烷转化率达到88.53%,甲苯的选择性达94.63%。     

异丁烷催化脱氢制异丁烯Cr2O3／Al2O3体系催化剂

对异丁烷催化脱氢催化剂进行了研究。助催化剂Ｋ２Ｏ,ＣｕＯ的引入改进了Ｃｒ２Ｏ３／Ａｌ２Ｏ３催化剂的活性和抗积炭性能。同时考察了原料气空速、反应温度以及催化剂制备的焙烧温度对Ｋ２Ｏ－ＣｕＯ－Ｃｒ２Ｏ３／Ａｌ２Ｏ３催化剂反应性能的影响。ＸＲＤ谱图表明,Ｃｒ２Ｏ３在催化剂中高分散,７００℃焙烧的催化剂中出现的ＫＣｕＯ晶相对催化剂活性不利。用ＮＨ３－ＴＰＤ和ＣＯ２－ＴＰＤ检测了催化剂表面的酸碱中心,表明助     

氧化铝载体硫酸化对锰铈催化剂SCR脱硝性能的影响

分别以硫酸改性前后的氧化铝为载体,采用浸渍法制备了锰铈催化剂,对其NH_3-SCR脱硝性能进行评价,并采用XRD、BET、NH_3-TPD、H_2-TPR以及FT-IR对催化剂进行了表征。结果表明,改性降低了金属的分散性和氧化性,增加了酸量,特别是B酸量;催化剂的最佳脱硝温度窗口向高温扩展,活性温度窗口范围变宽,并且,改性液浓度越大变化幅度越大。当反应温度在200-250℃时,未改性催化剂与采用0.2 mol/L硫酸改性的催化剂具有接近的催化活性,但改性后的催化剂具有更高的抗水抗硫活性,250℃时脱硝率可达70%。     

焙烧温度对二甲醚水蒸气重整制氢 Cu/ZnO/Al2O3/Cr2O3+H-ZSM-5双功能催化剂性能的影响

采用共沉淀耦合机械混合法制备了Cu/ZnO/Al₂O₃/Cr₂O₃+H-ZSM-5双功能催化剂,并用于二甲醚水蒸气重整制氢反应,结合热重、傅里叶红外光谱、XRD、BET、H₂-TPR表征,考察了焙烧温度对Cu/ZnO/Al₂O₃/Cr₂O₃催化剂物理化学性质及双功能催化剂催化性能的影响。研究结果表明,400℃焙烧时,析出CuO粒子的同时伴有尖晶石相,进而在反应过程中对金属铜粒子起到良好的隔离作用。而焙烧温度较低时,催化剂分解不完全,催化剂活性位较少。焙烧温度大于500℃时,CuO粒子发生二次团聚,同时尖晶石相大量生成,造成催化剂活性位减少,活性较低。合适的焙烧温度为400℃,此时二甲醚转化率为92.9%,氢气收率可达到76.5%,具有较好的反应效果。     

Ru/Al2O3-catalyzed transfer dehydrogenation of alcohols

Summary Primary and secondary alcohols were oxidized to their corresponding aldehydes or ketones in good yields using Ru/Al₂O₃ as catalyst in the presence of acetone. The catalyst can be recovered by simple filtration and reused after washing with acetone.     

Cr2O3气相催化1,1,2-三氯乙烷脱HCl性能

采用沉淀法制备了不同焙烧温度的Cr₂O₃催化剂,用于1,1,2-三氯乙烷(TCE)气相脱氯化氢制备二氯乙烯的反应。 采用X射线衍射(XRD)、氢气程序升温还原(H₂-TPR)、氨气程序升温脱附(NH₃-TPD)、X射线光电子能谱(XPS)表征手段,研究了Cr₂O₃催化剂气相催化裂解TCE脱氯化氢反应及其反应机理。 结果表明,Cr₂O₃催化剂上TCE气相脱氯化氢反应的转化率随着催化剂焙烧温度的升高逐渐降低,然而顺-1,2-二氯乙烯(cis-DCE)的选择性先增大后减小。 400 ℃焙烧的Cr₂O₃催化剂催化性能最好,TCE转化率为70.8%,顺-1,2-二氯乙烯的选择性为90.0%。 然而,催化剂的单位面积反应速率随着焙烧温度升高先提高后下降,400 ℃焙烧催化剂的单位面积反应速率为0.801×10^-2 μmol/(s·m²)。 催化剂的单位面积反应速率和顺-1,2-二氯乙烯(cis-DCE)的选择性与催化剂表面Cr₂O₃物种具有很好的对应关系,表明催化剂表面Cr₂O₃物种有利于脱氯化氢反应。 以酸中心为活性中心计算得到的转换频率(TOF)变化趋势与单位面积反应速率相一致,400 ℃焙烧的催化剂的TOF为2.82×10^-5 s^-1,表明Cr₂O₃催化剂Cr物种合适的平均价态(~3.20)有利于脱氯化氢反应。     

Oxidative addition of hydrogen in the “reduced” Mo/Al2O3 catalysts

An X-ray photoelectron spectroscopy study of Mo/Al₂O₃ catalysts prepared via [Mo^V ₂O₄(C₂O₄)₂(H₂O)₂]^2- complexes showed that after heating the catalysts with hydrogen in the spectrometer chamber, the position of the Mo3d line shifted to higher values of binding energy. This shift is interpreted as oxidative addition of hydrogen to the surface Mo species. A similar phenomenon was observed for a CO treated catalyst. A temperature-programmed desorption study has shown that hydrogen is strongly bounded to Mo and can only be removed from the catalysts at temperatures as high as 500°C. This revised version was published online in June 2006 with corrections to the Cover Date.     

Oxygen species on NiO/Al2O3 and their reactivities

Oxygen species on fresh and treated NiO/Al₂O₃ and their activities for oxidation of ethane and ethylene were investigated using catalytic property measurements, ethane and ethylene pulse experiments and O₂–TPD–MS experiments. The results revealed that there are two kinds of active oxygen species (the more active one and the less active one) on fresh NiO/Al₂O₃ catalyst, but there is only one active oxygen species, the less active one, on treated NiO/Al₂O₃ catalyst. The more active oxygen species can convert ethane or ethylene to carbon dioxide by one step while the less active one can only convert ethane to ethylene, but cannot convert ethane and/or ethylene to carbon dioxide. The more active oxygen species can be removed from the catalyst by heating from 350 to 850 °C. The amounts of desorption oxygen on the catalysts are proportional to their selectivity to carbon dioxide.     

TPR studies on steam reforming of 2-propanol on Rh/Al2O3, Ru/Al2O3 and Pd/Al2O3

Reaction pathways for steam reforming of 2-propanol (isopropyl alcohol, IPA) on Rh/Al₂O₃, Ru/Al₂O₃ and Pd/Al₂O₃ have been studied by temperature-programmed reactions (TPRs) of IPA and acetone in the presence of steam. The results of TPRs suggest that that of IPA on Rh/Al₂O₃ and Ru/Al₂O₃ proceeds via acetone, while the steam reforming of IPA on Pd/Al₂O₃ takes place via propene from acetone. This revised version was published online in August 2006 with corrections to the Cover Date.     

Oxidative dehydrogenation of propane over Mo/g-Al2O3. effect of precursor

Alumina supported molybdenum oxide was prepared using ammonium heptamolybdate and molybdenum acetate as different precursors. The catalysts were characterized by BET, AAS, SEM-EDAX, XRD, TPR and surface acidity measurements. The characterization results and the catalytic behavior in oxydehydrogenation of propane were similar irrespective of precursor. This revised version was published online in August 2006 with corrections to the Cover Date.     

Selective catalytic reduction of NO over metal oxide or noble metal-doped In2O3/Al2O3 catalysts by propene in the presence of oxygen

The activities of metal oxide CuO, SnO₂, CoO, Ag₂O, ZnO or noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts for selective catalytic reduction of NO by propene were investigated. The temperature windows for NO reduction over noble metal-doped In₂O₃/Al₂O₃ catalysts were shifted and broaden slightly compared with single component catalyst alone. This revised version was published online in June 2006 with corrections to the Cover Date.