Extraction and Spectrophotometric Determination of Osmium by Tetramethylthiuram Disulphide in Toluene

Summary Tetramethylthiuram disulphide (TMTD) is used for the extraction and spectrophotometric determination ofg quantities of osmium. 15 ml of 1.052×10^–3 M TMTD in toluene quantitatively extracts osmium from7 M HCl. The complex attains maximum colour intensity in 2 hours. It is red in colour and exhibits two max. One at 445 nm and the other at 504 nm. The maximum at 504 nm is more significant. Beer's law was found to hold good over the concentration range of 1.7 to 26.7g of osmium per ml. The Ringbom plot shows the optimum range of 9.42 to 23.65g of osmium per ml. The optimum period of equilibration is 30 seconds and the complex is stable up to 5 hours. The extracted species shows the composition to be 1 1 (Os TMTD). It is possible to extract and determine osmium in the presence of other platinum metals with composition corresponding to the ore osmiridium.

---

Zusammenfassung Tetramethylthiuramdisulfid (TMTD) wurde zur Extraktion und spektrophotometrischen Bestimmung von Mikrogrammengen Osmium verwendet. 15 ml einer 1,052.10^–3-molaren Lösung von TMTD in Toluol dienen zur Extraktion von Os aus 7-m Salzsäure. Der entstandene rote Komplex erreicht innerhalb 2 Stunden maximale Farbintensität und zeigt zwei Absorptionsmaxima bei 445 nm und 504 nm. Letzteres ist signifikanter. Zwischen 1,7 und 26,7g Os/ml gilt das Beersche Gesetz. Nach der Ringbom-Gleichung liegt die geeignetste Konzentration zwischen 9,42 und 23,65g Os/ml. Nach 30 sec stellt sich das Gleichgewicht ein und bleibt bis zu 5 Stunden konstant. Die extrahierte Substanz entspricht der Zusammensetzung 1 1 (Os TMTD). Os läßt sich auch in Gegenwart anderer Platinmetalle so extrahieren und bestimmen.

     

Spectrophotometric determination of osmium using phenanthrenequinone monosemicarbazone (PQCS) as a sensitive and selective reagent

Summary The reddish brown complex formed by osmium(VIII) and phenanthrenequinone monosemicarbazone, has an absorption maximum at 500 nm with molar absorptivity of 1.85×10⁴ 1 cm^–1 mole^–1. This complex is used to determine 50–198g osmium(VIII) in 37 DMF-methanol medium. The pH range for the determination is 7.2–9.2. The limits of interference due to foreign ions have been studied.

---

Spektrophotometrische Bestimmung von Osmium mit Phenanthrenchinon-Monosemicarbazon als empfindlichem und selektivem Reagens

Zusammenfassung Der aus Osmium(VIII) und Phenanthrenchinon-Monosemicarbazon entstehende rotbraune Komplex hat sein Absorptionsmaximum bei 500 nm. Die molare Extinktion beträgt 1,85×10⁴ l·cm^–1·Mol^–1. Dieser Komplex diente zur Bestimmung von 50–198g Osmium(VIII) in einer Lösung aus DMF und Methanol im Verhältnis 37. Das einzuhaltende pH liegt zwischen 7,2 und 9,2. Die Störungen durch Fremdionen wurden untersucht.

     

Trace element analysis of some shaving powders commonly marketed in Nigeria using instrumental neutron activation analysis

Instrumental neutron activation analysis (INAA) technique has been employed viak ₀ approximation method to determine elemental composition of five shaving powders commonly marketed in Nigeria. Fe displayed the highest concentrations in the range 1000–2000 g·g^–1. Na and Zn concentrations were established in the range 200–400 g·g^–1. Heavy elements like Ga, La, Cr, Co, Ag, Ce and Nd concentrations were noted in the lower range of 1–10 g·g^–1 Br, As, Sb, Sm, Eu, W, Cs, Tb, Yb, Hf, Ta, Th and U concentrations were established in even lower traces in the <1 g·g^–1 range. Results obtained for a certified reference material, CANMET BL-1 and CERT (in house) Kaolin standard compared favourably with the literature values thus establishing the results presented for the shaving powders.     

The composition of volatile and particulate hydrocarbons in urban air

Summary The hydrocarbon composition of the particle and gas phases in the urban atmosphere has been studied by filtration and parallel adsorption on active charcoal and polyurethane foam (PUF). Gas chromatography (GC) and GC coupled to mass spectrometry (GC-MS) have been used for the analysis of the organic matter extracts obtained with each system. In the case of the particle and PUF samples these extracts were fractionated into aliphatic and aromatic compounds. This approach has allowed to identify up to 247 hydrocarbon molecules showing that C0–C5 alkylbenzenes are the major compounds in the charcoal extracts whereas C14–C23 n-alkanes, C0–C4 alkylnaphthalenes, C0–C4 alkylbiphenyls and C3–C5 alkylbenzenes are those predominantly found in the PUF materials. The particles essentially contain C17–C38 n-alkanes and parent polycyclic aromatic hydrocarbons (PAH). These qualitative differences are paralleled by a progressive concentration decrease from the more to the less volatile hydrocarbons. Thus, the total charcoal extracts average 80 g/m³, the PUF compounds represent 4 /m³ and the particle hydrocarbons 0.7 g/m³. These latter airborne materials are essentially composed of petrogenic residues 0.6 g/m³ (aliphatic fraction) whereas the pyrolytic PAH only involve 0.08 g/m³.     

Path of “dry” electrons before localization in liquid hydrocarbons

Conclusions On the basis of measurements of values of in liquid hydrocarbons, it has been shown that the path length before localization of a photoliberated electron increases with increasing mobility of the excess electron, from approximately 40 Å (methylcyclohexane) to 200 Å (isooctane). In a liquid with10^–2 cm²/V·sec (methylcyclohexane, hexane), the localization takes place before or immediately after thermalization of the electron. In a liquid with>10^–1 cm²/V·sec, the electron passes through the main part of its path before localization, being in thermal equilibrium with the medium.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 10, pp. 2198–2203, October, 1985.     

Extractive spectrophotometric determination of dioxouranium(VI) with the sodium salt of hexamethyleneiminecarbodithioate

The optimum conditions for the extractive spectrophotometric determination of dioxouranium(VI) with hexamethyleneiminecarbodithioate(HMICdt) have been established. Dioxouranium(VI) reacts with this ligand at pH 4.5 to form a yellowish-orange uncharged 12 metal-ligand complex which can be extracted by chloroform. The calibration graph was linear in the range of 1–20 g ml^–1 of dioxouranium(VI) at 335 nm. The molar absorptivity of the extracted species is 5.952×10³ l mol^–1 cm^–1 with Sandell's sensitivity of 0.04 g cm^–2. The average of 10 determinations of dioxouranium was 49.75 g for the samples containing 50 g of U(VI) and the variation from the mean at 95% confidence limit was 49.75±0.5955.     

Addition of HCl to a Cluster-Bound Vinylidene Ligand: Preparation and Structure of Ru5(μ3-SMe)(μ3-CMe)(μ-Cl)(μ-SMe)(μ-PPh2)2(CO)9·PhMe

Addition of aqueous HCl to Ru₅( ₃-C=CH₂)(-SMe)₂(-PPh₂)₂(CO)₁₀ afforded the structurally characterized carbyne complex Ru₅( ₃-SMe)( ₃-CMe)(-Cl)(-SMe)(-PPh₂)₂(CO)₉, formed by addition of H to the vinylidene ligand; a Cl atom bridges an Ru–Ru bond.     

Simultaneous Determination of Four Active Components in a Compound Formulation by Liquid Chromatography

Summary A rapid and accurate LC method is described for simultaneous determination of pseudoephedrine hydrochloride (PSE), acetaminophen (AMP), dextromethorphen hydrobromide (DEX), and diphenhydramine hydrochloride (DPH) in a compound formulation. Chromatographic separation of the four drugs was achieved on a Hypersil CN column (150 mm × 4.6 mm, 5 m particle) by use of a mobile phase comprising a mixture of 3 mM ion-pairing solution, 2% aqueous triethylamine solution, and 2 M phosphoric acid, 68:48:88 (v/v), pH 3.0, delivered at 1.0 mL min^–1. Compounds were detected at 215 nm and the run time was less than 10 min. The linearity, accuracy, and precision of the method were found to be acceptable over the concentration ranges 6.1–36.4 g mL^–1 for PSE, 65.0–390.0 g mL^–1 for AMP, 3.1–18.6 g mL^–1 for DEX, and 5.0–30.0 g mL^–1 for DPH.     

Fällungsanalyse im Mikrogrammbereich: Eine neue Methode

Zusammenfassung Eine neue Methode zur Durchführung gravimetrischer Bestimmungen im Mikrogrammbereich wurde beschrieben; diese beruht im wesentlichen darauf, daß der Niederschlag nicht mehr zusammen mit dem Filter, sondern nach Überführen mit einem geeigneten Lösungsmittel in einem separaten Wägegefäß gewogen wird.Die dazu nötigen Geräte und deren Herstellung wurden beschrieben. Nach dieser Methode wurden folgende Bestimmungen mit zufriedenstellender Richtigkeit durchgeführt: 2,5–25g Al, 5–50g Cu und 5–50g Zn mit Oxin, 2,5–25g Fe(III) und 2,5–25g Ti(IV) mit N-Benzoyl-phenylhydroxylamin, 5–50g Ni und 5–50g Cu mit Salicylaldoxim, 2,5–50g Co(II) und 2,5–50g Fe(III) mit -Nitroso--naphthol sowie 5–50g Chlorid als Silberchlorid.

---

Precipitation analysis in the microgram-scale: A new method

Summary A new method for gravimetric determinations in the microgram-scale is described. This method is based on the fact that the precipitate is not weighed together with the filter but is transferred to a separate weighingvessel using a suitable solvent. The necessary simple devices and their use are described. The following determinations were carried out with satisfying accuracy: 2,5–25g Al, 5–50g Cu and 5–50g Zn with Oxine, 2,5–25g Fe and 2,5–25g Ti withN-benzoylphenylhydroxylamine, 5–50g Ni and 5–50g Cu with salicylaldoxime, 2,52–50g Co and 2,5–50g Fe with -nitroso--naphthol and 5–50g chloride as silver chloride.

     

Determination of nitrate in natural waters by flow-injection analysis

Summary Nitrate was determined in natural water samples by flow-injection spectrophotometry. It was reduced to nitrite with copperized cadmium and the nitrite thus produced reacted with p-aminoacetophenone and m-phenylenediamine. The limit of detection was about 1.5 g l^–1 for sample injections of 650 l. The sampling rate was about 40 samples h^–1 and the relative standard deviation was above 1% for 0.1–0.3 mg l^–1 nitratenitrogen. Nitrite present in the sample was determined separately and subtracted.

---

Nitratbestimmung in natürlichen Wässern mit Hilfe der Fließinjektions-Analyse

Zusammenfassung Nitrat wird bei dieser Methode mit Hilfe einer Cu/Cd-Reduktionssäule zu Nitrit reduziert, das mit p-Aminoacetophenon und m-Phenylendiamin zur Reaktion gebracht wird. Die gebildete Verbindung wird spektral-photometrisch gemessen. Die Nachweisgrenze beträgt etwa 1,5 g/l bei injizierten Probevolumina von 650 l. Der Probendurchsatz beträgt 40/h. Die relative Standardabweichung liegt über 1% bei 0,1–0,3 mg/l Nitrat-Stickstoff. Vorhandenes Nitrit wird gesondert bestimmt und abgezogen.

     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

Determination of pentachlorophenol residues in wine and corks by solvent extraction methodology and specific gas chromatography detection

Summary A gas chromatographic methodology with selective detection is presented for the analysis in wines and corks of pentachlorophenol residues, which are suspected to be the most likely precursors of some off-flavours described in several wine samples. After derivatisation, pentachlorophenol acetate residues were monitored by electrolytic conductivity detection and/or mass spectrometric detection in the selective ion mode at m/z 264 and 266. Recoveries varied from 80 to 96% for wine samples fortified with 5 to 100 g l^–1 and from 83 to 91% for corks (fortified at 25 to 100 g kg^–1). The proposed methodology allowed for a determination limit of g l^–1 for wine and 10 g kg^–1 for corks.     

Titrimetric determination of thiourea and silver with a picrate ion selective electrode

Summary A method has been developed for the semiautomatic potentiometric titration of thiourea with silver nitrate and of silver with thiourea, in the presence of picrate ions, using a picrate ion selective electrode. Thiourea in the range 15–1500g and silver in the range 200–1800g were determined with relative errors and relative standard deviation of about 1%.

---

Zusammenfassung Eine halbautomatische potentiometrische Titrationsmethode für Thioharnstoff mit Silbernitrat bzw. umgekehrt in Gegenwart von Pikrationen mit Hilfe einer selektiven Pikratelektrode wurde entwickelt. 15–1500g Thioharnstoff bzw. 200–1800g Silber wurden mit einem relativen Fehler und einer relativen Standardabweichung von etwa ±1% bestimmt.

     

Determination of some trace elements in high-purity aluminium, zinc and commercial steel by AAS after preconcentration on amberlite XAD-1180 resin

The determination of trace metals, e.g. Bi, Cd, Pb, in high-purity aluminium, zinc and commercial steel by flame or graphite furnace atomic absorption spectrometry following their preconcentrations as iodo complexes on XAD-1180 resin by means of a short column system is described. The recoveries are quantitative (95%). The relative standard deviations varies between 6% and 10%. The relative errors are less than 8% in a concentration range of 1 × 10^–3 –4 × 10^–5%. Detection limits for flame AAS and GFAAS were in the ranges of 0.002–0.110 g/ml and 0.0003–0.004 g/ml or in the ranges of 0.08–4.40 g/g and 0.012–0.16 g/g with respect to the solid samples, respectively.     

Simultaneous determination of neodymium and erbium in rare earth mixture with 5,7-dibromo-8-hydroxyquinoline and TX-100 by third-derivative spectrophotometry

The absorption spectra of 4f electron transitions of the complexes of neodymium and erbium with 5,7-dibromo-8-hydroxyquinoline in the presence of octylphenol poly(ethyleneglycol)ether have been studied by normal and third-derivative spectrophotometry. The proposed method is free of interference of other rare earths. The calibration graphs were linear up to 18 g/ml of neodymium and 21 g/ml of erbium (in the final solution). The derivative molar absorptivities are 395 l.mol^–1.cm^–1 for neodymium and 3421.mol^–1.cm^–1 for erbium. The corresponding values of Sandell's sensitivity were 0.36 and 0.49 g.cm^–1, respectively. The relative standard deviations evaluated from ten independent determinations of 2.5 g/ml of neodymium and erbium are 1.5 and 3.8% for neodymium and 1.8 and 4.1% for erbium in absence and presence of 70 g of lanthanum, respectively. The detection limits (signal to noise ratio=2) are 0.23 g/ml for neodymium and 0.30 g/ml for erbium. The method has been used for the determination of neodymium and erbium in mixed rare earths with satisfactory results.     

New books

Summary Micromolar analyses of the nitrogen species NH₃, NO ₂ ^– , and NO ₃ ^– in soil and other samples are usually accomplished by extracting several samples and testing each for a different species. This procedure is not viable when the quantity of the initial sample is limited. An improved method of separating and analysing for ammonia NH₃(aq), nitrite NO ₂ ^– (aq), and nitrate NO ₃ ^– (aq) from a single small sample with concentrations of 0–50 mol/l is reported. No interferences or carryovers among the three nitrogen containing species were found. Uncertainties were ±2–5 mol/l and accuracies with respect to standards were ±3 mol/l.     

Fourth-derivative spectrophotometric determination of neodymium in mixed rare earths with methyl thymol blue and cetylpyridinium chloride

A sensitive and selective method is described for the determination of neodymium in mixed rare earths using fourth-derivative spectrophotometry. The method is based on the absorption spectra of 4f electron transitions of the complex of neodymium with methyl thymol blue and cetylpyridinium chloride. The influence of various instrumental parameters and reaction conditions for maximum colour development are investigated. The calibration curve is linear over the range 0–3.5 g ml^–1 neodymium. The relative standard deviation for determination of 1.4 g ml^–1 neodymium (n = 7) is 1.6%. The detection limit (signal-to-noise ratio = 3) is 0.2 g ml^–1.     

Thiazane-2, 4-dithione and its 3-aryl derivatives

Reaction of 2-thiothiazane-4-one and its 3-aryl derivatives with phosphorus pentasulfide in toluene or dichloroethane gives thiazane-2, 4-dithione, or the corresponding 3-aryl derivatives. The compounds are characterized by absorption maxima (or bends) at three bands, 244–262, 315–321, and 339–350 m. The IR spectra exhibit bands at 14.93 (C-S-C), 6.64, and 6.84 (N-C-S), and 7.34, 8.43, 7.14 (CH₂).     

Zur Bestimmung N-substituierter Aniline mit Natriumchlorit

Zusammenfassung Es wird eine photometrische Bestimmungsmethode beschrieben für Anilin (40–720 g/ml), Monoäthylanilin (90–1650 g/ml) und Diäthylanilin (100–1600 g/ml) mit Natriumchlorit in äthanolisch-wäßrigen Lösungen, sowie für Diäthylanilin (85–1140 g/ml) und Dimethylanilin (30–330 g/ml) neben den primären und sekundären Aminen in essigsaurer Lösung mit demselben Reagens. Das Verfahren liefert gute Ergebnisse.

---

Summary A photometric procedure is described for the determination of aniline (40–720 g/ml), monoethylaniline (90–1650 g/ml), and diethylaniline (100–1600 g/ml) with sodium chlorite in aqueous ethanolic solutions and of diethylaniline (85–1140 g/ml) and dimethylamline (30 to 330 g/ml) in presence of the primary and secondary amines in acetic acid solution using the same reagent. Good results have been obtained,