Stability and reversibility of LiBH4

LiBH4 is a complex hydride and exhibits a high gravimetric hydrogen density of 18.5 wt %. Therefore it is a promising hydrogen storage material for mobile applications. The stability of LiBH4 was investigated by pcT (pressure, concentration, and temperature) measurements under constant hydrogen flows and extrapolated to equilibrium. According to the van 't Hoff equation the following thermodynamic parameters are determined for the desorption: enthalpy of reaction DeltarH = 74 kJ mol-1 H2 and entropy of reaction DeltarS = 115 J K-1 mol-1 H2. LiBH4 decomposes to LiH + B + 3/2H2 and can theoretically release 13.9 wt % hydrogen for this reaction. It is shown that the reaction can be reversed at a temperature of 600 degrees C and at a pressure of 155 bar. The formation of LiBH4 was confirmed by XRD (X-ray diffraction). In the rehydrided material 8.3 wt % hydrogen was desorbed in a TPD (temperature-programmed desorption) measurement compared to 10.9 wt % desorbed in the first dehydrogenation.     

Reversible storage of hydrogen in destabilized LiBH4

Destabilization of LiBH4 for reversible hydrogen storage has been studied using MgH2 as a destabilizing additive. Mechanically milled mixtures of LiBH4 + (1/2)MgH2 or LiH + (1/2)MgB2 including 2-3 mol % TiCl3 are shown to reversibly store 8-10 wt % hydrogen. Variation of the equilibrium pressure obtained from isotherms measured at 315-400 degrees C indicate that addition of MgH2 lowers the hydrogenation/dehydrogenation enthalpy by 25 kJ/(mol of H2) compared with pure LiBH4. Formation of MgB2 upon dehydrogenation stabilizes the dehydrogenated state and, thereby, destabilizes the LiBH4. Extrapolation of the isotherm data yields a predicted equilibrium pressure of 1 bar at approximately 225 degrees C. However, the kinetics were too slow for direct measurements at these temperatures.     

化学计量比和放氢背压对LiBH4+xMg2NiH4体系放氢性能的影响

研究了不同化学计量比(x=0.25, 0.5, 0.75, 1.0, 1.25)和放氢背压(1×10-4和0.4 MPa)对LiBH4+xMg2NiH4复合体系吸放氢性能的影响. 结果表明, 随着化学计量比(x)的增加, 复合体系的放氢温度逐渐降低, 放氢动力学性能得到提高, 但放氢容量逐渐降低; 其中, 在1×10-4和0.4 MPa初始放氢背压下, LiBH4+0.75Mg2NiH4体系具有最佳放氢动力学性能和较高的储氢容量. 结果表明, 放氢背压和化学计量比均会对高温下液相LiBH4 与固态Mg2NiH4 的润湿性产生影响, 进而影响复合体系的放氢路径和放氢动力学性能.     

Hydrogen desorption exceeding ten weight percent from the new quaternary hydride Li3BN2H8

Mobile applications of hydrogen power have long demanded new solid hydride materials with large hydrogen storage capacities. We report synthesis of a new quaternary hydride having the approximate composition Li(3)BN(2)H(8) with 11.9 wt % theoretical hydrogen capacity. It forms by reacting LiNH(2) and LiBH(4) powders in a 2:1 molar ratio either by ball milling or by heating the mixed powders above 95 degrees C. This new quaternary hydride melts at approximately 190 degrees C and releases > or =10 wt % hydrogen above approximately 250 degrees C. A small amount of ammonia (2-3 mol % of the generated gas) is released simultaneously. Preliminary calorimetric measurements suggest that hydrogen release is exothermic and, hence, not easily reversible.     

Functions of MgH(2) in hydrogen storage reactions of the 6LiBH(4)-CaH(2) reactive hydride composite

A significant improvement of hydrogen storage properties was achieved by introducing MgH(2) into the 6LiBH(4)-CaH(2) system. It was found that ～8.0 wt% of hydrogen could be reversibly stored in a 6LiBH(4)-CaH(2)-3MgH(2) composite below 400 °C and 100 bar of hydrogen pressure with a stepwise reaction, which is superior to the pristine 6LiBH(4)-CaH(2) and LiBH(4) samples. Upon dehydriding, MgH(2) first decomposed to convert to Mg and liberate hydrogen with an on-set temperature of ～290 °C. Subsequently, LiBH(4) reacted with CaH(2) to form CaB(6) and LiH in addition to further hydrogen release. Hydrogen desorption from the 6LiBH(4)-CaH(2)-3MgH(2) composite finished at ～430 °C in non-isothermal model, a 160 °C reduction relative to the 6LiBH(4)-CaH(2) sample. JMA analyses revealed that hydrogen desorption was a diffusion-controlled reaction rather than an interface reaction-controlled process. The newly produced Mg of the first-step dehydrogenation possibly acts as the heterogeneous nucleation center of the resultant products of the second-step dehydrogenation, which diminishes the energy barrier and facilitates nucleation and growth, consequently reducing the operating temperature and improving the kinetics of hydrogen storage.     

Modified lithium borohydrides for reversible hydrogen storage

In an attempt to develop lithium borohydrides as reversible hydrogen storage materials with high hydrogen storage capacities, the feasibility of reducing the dehydrogenation temperature of the lithium borohydride and moderating rehydrogenation conditions was explored. The lithium borohydride was modified by ball milling with metal oxides and metal chlorides as additives. The modified lithium borohydrides released 9 wt % hydrogen starting from 473 K. The dehydrided modified lithium borohydrides absorbed 7-9 wt % hydrogen at 873 K and 7 MPa. The modification with additives reduced the dehydriding starting temperature from 673 to 473 K and moderated the rehydrogenation conditions from 923 K/15 MPa to 873 K/7 MPa. XRD and SEM analysis revealed the formation of an intermediate compound that might play a key role in changing the reaction path, resulting in the lower dehydriding temperature and reversibility. The reversible hydrogen storage capacity of the oxide-modified lithium borohydrides decreased gradually during hydriding/dehydriding cycling. One of the possible reasons for this effect might be the loss of boron during dehydrogenation, but this can be prevented by changing the dehydriding path using appropriate additives. The additives reduced the dehydriding temperature and improved the reversibility, but they also reduced the hydrogen storage capacity. The best compromise can be reached by selecting appropriate additives, optimizing the additive loading, and using new synthesis processes other than ball milling.     

Promoted dehydrogenation in ammine lithium borohydride supported by carbon nanotubes

In this paper, ammine lithium borohydride (LiBH(4)·NH(3)) was successfully impregnated into multi-walled carbon nanotubes (CNTs) through a melting technique. X-ray diffraction, scanning electron microscopy, Brunauer-Emmett-Teller, and density measurements were employed to confirm the formation of the nanostructured LiBH(4)·NH(3)/CNTs composites. As a consequence, it was found that the dehydrogenation of the loaded LiBH(4)·NH(3) was remarkably enhanced, showing an onset dehydrogenation at temperatures below 100 °C, together with a prominent desorption of pure hydrogen at around 280 °C, with a capacity as high as 6.7 wt.%, while only a trace of H(2) liberation was present for the pristine LiBH(4)·NH(3) in the same temperature range. Structural examination indicated that the significant modification of the thermal decomposition route of LiBH(4)·NH(3) achieved in the present study is due to the CNT-assisted formation of B-N-based hydride composite, starting at a temperature below 100 °C. It is demonstrated that the formation of this B-N-based hydride covalently stabilized the [NH] groups that were weakly coordinated on Li cations in the pristine LiBH(4)·NH(3)via strong B-N bonds, and furthermore, accounted for the substantial hydrogen desorption at higher temperatures.     

3LiBH4/CeF3体系的放氢性能及机制

采用球磨法制备了3LiBH₄/CeF₃反应体系, 通过压力-组成-温度(PCT)测试仪、 X射线衍射仪(XRD)和傅里叶变换红外光谱仪(FTIR)研究了体系的放氢性能、 反应机制及性能改善机理. 结果表明, 3LiBH₄/CeF₃体系在295 ℃左右快速放氢, 总放氢量为4.1%(质量分数). 放氢过程中CeF₃与LiBH₄直接发生反应: 3LiBH₄+CeF₃1/2CeB₆+1/2CeH₂+3LiF+11/2H₂. 与纯LiBH₄相比, 放氢热力学稳定性和表观活化能的降低是3LiBH₄/CeF₃体系放氢温度下降的主要原因.     

Hydrogen release from mixtures of lithium borohydride and lithium amide: a phase diagram study

We recently reported the synthesis of a new quaternary hydride in the lithium-boron-nitrogen-hydrogen quaternary phase diagram with the approximate composition LiB0.33N0.67H2.67 having a theoretical hydrogen content of 11.9 wt %. This new compound forms by the reaction of appropriate amounts of lithium amide (LiNH2) and lithium borohydride (LiBH4) and releases greater than 10 wt % hydrogen when heated. A small amount of ammonia, 2-3 mol % of the generated gas, is also released. We now report a study of hydrogen and ammonia release from the series of reactant mixtures (LiNH2)x(LiBH4)1-x, where x=0.667 corresponds to the composition LiB0.33N0.67H2.67. We measured hydrogen and ammonia release amounts as a function of composition and found that maximum hydrogen and minimum ammonia release do occur for x=0.667. We also present evidence for an additional new quaternary phase and for two possibly metastable phases in this system.     

Identification of destabilized metal hydrides for hydrogen storage using first principles calculations

Hydrides of period 2 and 3 elements are promising candidates for hydrogen storage but typically have heats of reaction that are too high to be of use for fuel cell vehicles. Recent experimental work has focused on destabilizing metal hydrides through alloying with other elements. A very large number of possible destabilized metal hydride reaction schemes exist. The thermodynamic data required to assess the enthalpies of these reactions, however, are not available in many cases. We have used first principles density functional theory calculations to predict the reaction enthalpies for more than 100 destabilization reactions that have not previously been reported. Many of these reactions are predicted not be useful for reversible hydrogen storage, having calculated reaction enthalpies that are either too high or too low. More importantly, our calculations identify five promising reaction schemes that merit experimental study: 3LiNH(2) + 2LiH + Si --> Li(5)N(3)Si + 4H(2), 4LiBH(4) + MgH(2) --> 4LiH + MgB(4) + 7H(2), 7LiBH(4) + MgH(2) --> 7LiH + MgB(7) + 11.5H(2), CaH(2) + 6LiBH(4) --> CaB(6) + 6LiH + 10H(2), and LiNH(2) + MgH(2) --> LiMgN + 2H(2).     

Cobalt-catalyzed hydrogen desorption from the LiNH2-LiBH4 system

A doping of 5 wt% CoCl2 considerably decreases the dehydrogenation temperature of a mixture of LiNH2 and LiBH4. More that 8 wt% of hydrogen can be released at ca. 155 degrees C. X-Ray absorption near edge structure (XANES) spectroscopy indicated the formation of metallic Co after ball milling CoCl2 with LiNH2 and LiBH4. Extended X-ray absorption fine structure (EXAFS) spectroscopy measurements revealed that Co particles have poor crystallinity and are finely dispersed in the sample, which could lead to a high catalytic efficiency.     

Improved hydrogen release from LiB0.33N0.67H2.67 with noble metal additions

The hydrogen release behavior of the quaternary hydride LiB(0.33)N(0.67)H(2.67) has been successfully improved through the incorporation of small quantities of noble metal. Adding 5 wt % Pd either as Pd metal particles or as PdCl(2) reduced the temperature T(1/2) corresponding to the midpoint of the hydrogen release reaction by DeltaT(1/2) = -43 degrees C and -76 degrees C, respectively. PtCl(2) and Pt nanoparticles supported on a Vulcan carbon substrate proved to be even more effective, with DeltaT(1/2) = -90 degrees C. The amount of NH(3) released during dehydrogenation is reduced compared to that from additive-free material, and, more importantly, at temperatures below 210 degrees C hydrogen is released with no detectable NH(3). In contrast to additive-free LiB(0.33)N(0.67)H(2.67), which melts completely above 190 degrees C and releases hydrogen from the liquid state only above approximately 250 degrees C, hydrogen release from LiB(0.33)N(0.67)H(2.67) + 5 wt % Pt/Vulcan carbon is accompanied by partial melting plus a cascade through a series of solid intermediate phases. Calorimetric measurements indicate that both additive-free and Pt-added LiB(0.33)N(0.67)H(2.67) release hydrogen exothermically, and hence the reverse reaction is thermodynamically unfavorable. By exposing partially dehydrogenated samples to high H(2) pressures at modest temperatures, fractional hydrogen uptake (roughly 15% of the released hydrogen) has been achieved. The mechanism by which noble metals promote hydrogen release is not known, but the behavior is consistent with that expected for a catalyst, including a large effect with small additions and saturation of the effect at low concentration.     

A new Li-Al-N-H system for reversible hydrogen storage

Complex metal hydrides are considered as a class of candidate materials for hydrogen storage. Lithium-based complex hydrides including lithium alanates (LiAlH(4) and Li(3)AlH(6)) are among the most promising materials owing to its high hydrogen content. In the present work, we investigated dehydrogenation/rehydrogenation reactions of a combined system of Li(3)AlH(6) and LiNH(2). Thermogravimetric analysis (TGA) of Li(3)AlH(6)/3LiNH(2)/4 wt % TiCl(3)-(1)/(3)AlCl(3) mixtures indicated that a large amount of hydrogen (approximately 7.1 wt %) can be released between 150 degrees C and 300 degrees C under a heating rate of 5 degrees C/min in two dehydrogenation reaction steps. The results also show that the dehydrogenation reaction of the new material system is nearly 100% reversible under 2000 psi pressure hydrogen at 300 degrees C. Further, a short-cycle experiment has demonstrated that the new combined material system of alanates and amides can maintain its hydrogen storage capacity upon cycling of the dehydrogenation/rehydrogenation reactions.     

Catalytic effect of nanoparticle 3d-transition metals on hydrogen storage properties in magnesium hydride MgH2 prepared by mechanical milling

We examined the catalytic effect of nanoparticle 3d-transition metals on hydrogen desorption (HD) properties of MgH(2) prepared by mechanical ball milling method. All the MgH(2) composites prepared by adding a small amount of nanoparticle Fe(nano), Co(nano), Ni(nano), and Cu(nano) metals and by ball milling for 2 h showed much better HD properties than the pure ball-milled MgH(2) itself. In particular, the 2 mol % Ni(nano)-doped MgH(2) composite prepared by soft milling for a short milling time of 15 min under a slow milling revolution speed of 200 rpm shows the most superior hydrogen storage properties: A large amount of hydrogen ( approximately 6.5 wt %) is desorbed in the temperature range from 150 to 250 degrees C at a heating rate of 5 degrees C/min under He gas flow with no partial pressure of hydrogen. The EDX micrographs corresponding to Mg and Ni elemental profiles indicated that nanoparticle Ni metals as catalyst homogeneously dispersed on the surface of MgH(2). In addition, it was confirmed that the product revealed good reversible hydriding/dehydriding cycles even at 150 degrees C. The hydrogen desorption kinetics of catalyzed and noncatalyzed MgH(2) could be understood by a modified first-order reaction model, in which the surface condition was taken into account.     

Ti-Zr催化剂对NaH/Al复合物可逆储氢特性的影响

采用机械球磨(NaH/Al+Ti)和(NaH/Al+Ti-Zr)复合物的方法加氢制备了NaAlH4配位氢化物, 系统研究了Ti、Ti-Zr催化剂以及不同加氢条件对其可逆储氢行为的影响. 结果表明, 对于NaH/Al体系的吸放氢性能, 共掺金属Ti粉/Zr粉的催化作用比单独掺金属Ti粉的催化作用要好. 随着加氢温度从85 ℃上升到140 ℃, 体系的吸氢容量先增后减, 并在120 ℃时达到最大值; 同时, 发现共掺Ti-Zr催化剂的复合物具有最佳的储氢性能, 在120和85 ℃时的吸氢量分别为4.61%和3.52%(w), 比仅掺Ti 催化剂的复合物分别高出0.40%和0.70%(w)的吸氢量. 随着加氢压力的增大, (NaH/Al+Ti-Zr)复合物的吸氢性能随之提高. XRD和DSC分析结果表明, NaAlH4体系的放氢过程明显发生两步分解反应, 共掺Ti-Zr催化剂的复合物储氢性能优于单独掺Ti 催化剂的原因是, 共掺催化剂能有效改善NaAlH4体系吸放氢反应的动力学性能,并降低体系的放氢温度.     

Fe2O3与TiF3添加剂对LiBH4-MgH2复合氢化物体系的协同催化作用

通过球磨方法制备出2LiBH4-MgH2,2LiBH4-MgH2-10%Fe2O3,2LiBH4-MgH2-10%TiF3,2LiBH4-MgH2-5%Fe2O3-5%TiF3和2LiBH4-MgH2-10%Fe2O3-10%TiF35个复合氢化物体系,用热重(TG)、差示扫描量热(DSC)、X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)和压力-组成-温度仪(PCT)等对所制备体系进行表征.结果表明,Fe2O3和TiF3的掺杂均能够有效地改善2LiBH4-MgH2复合体系的放氢性能,尤其是两者共掺杂的2LiBH4-MgH2-10%Fe2O3-10%TiF3体系,初始放氢温度为110℃,总放氢量达到约9.6%.对2LiBH4-MgH2-5%Fe2O3-5%TiF3体系的PCT表征结果表明,在400℃时,10 min内放氢量达到了8.6%,放氢热力学和放氢动力学均优于单一相的掺杂,体现了两相掺杂的协同催化作用.     

A study on the dehydriding kinetics in the Mg2Ni-Ni (< 5 wt.%)-H2 system

The dehydriding kinetics of the Mg₂Ni-Ni (< 5 wt.%)-H₂ system is studied at temperatures between 553 and 593 K under hydrogen pressures from 0.8 to 3.2 bar. In the temperature range from 553 to 563 K the nucleation of α-solid solution of hydrogen in Mg₂Ni is found to be the rate-controlling step for the dehydriding reaction. In the temperature range from 573 to 593 K the rate-controlling steps are Knudsen flow and ordinary gaseous diffusion of hydrogen molecules through pores, interparticle channels and cracks.     

MgH_2+20%(w)MgTiO_3复合材料的吸/放氢性能(英文)

为了降低MgH2的吸放氢温度,提高其吸放氢动力学性能,本文通过球磨方法制备了MgH2+20%(w)MgTiO3复合储氢材料,并研究了其储氢性能.X射线衍射(XRD)结果表明,MgTiO3在与MgH2球磨过程中生成Mg2TiO4和TiO2,并且Mg2TiO4和TiO2在体系的吸放氢过程中保持稳定,能够对MgH2的吸放氢过程产生催化作用.程序升温脱附和吸/放氢动力学测试结果表明,添加MgTiO3后MgH2的初始放氢温度从389°C降至249°C.150°C下的吸氢量从0.977%(w)提高到2.902%(w),350°C下的放氢量从2.319%(w)提高到3.653%(w).同时,MgH2放氢反应的活化能从116kJ·mol-1降至95.7kJ·mol-1.与MgH2相比,MgH2+20%(w)MgTiO3复合材料的热力学与动力学性能均有显著提高,这主要是由于球磨和放氢过程中原位生成的TiO2和Mg2TiO4具有良好的催化活性.     

Hydrogen-deuterium exchange in bulk LiBH4

Because of its apparent simplicity, diffusion of hydrogen in solids can be regarded as a general model system for diffusion. However, only rudimentary knowledge exists for the dynamics of hydrogen in complex hydrides. Insight into the specific diffusion process is given by hydrogen-deuterium exchange experiments. Thermogravimetry and Raman spectroscopy are used to measure the hydrogen-deuterium exchange during the decomposition of LiBH4. At a temperature of 523 K the self-diffusion constant of deuterium in LiBH4 is estimated to be D approximately 7 x 10(-14) m(2) s(-1). A careful analysis of the Raman spectra shows that hydrogen is statistically exchanged by deuterium in LiBH4; i.e., the diffusing species is assumed to be the single hydrogen atom.     

Ca(AlH4)2, CaAlH5, and CaH2+6LiBH4: Calculated dehydrogenation enthalpy, including zero point energy, and the structure of the phonon spectra

The dehydrogenation enthalpies of Ca(AlH(4))(2), CaAlH(5), and CaH(2)+6LiBH(4) have been calculated using density functional theory calculations at the generalized gradient approximation level. Harmonic phonon zero point energy (ZPE) corrections have been included using Parlinski's direct method. The dehydrogenation of Ca(AlH(4))(2) is exothermic, indicating a metastable hydride. Calculations for CaAlH(5) including ZPE effects indicate that it is not stable enough for a hydrogen storage system operating near ambient conditions. The destabilized combination of LiBH(4) with CaH(2) is a promising system after ZPE-corrected enthalpy calculations. The calculations confirm that including ZPE effects in the harmonic approximation for the dehydrogenation of Ca(AlH(4))(2), CaAlH(5), and CaH(2)+6LiBH(4) has a significant effect on the calculated reaction enthalpy. The contribution of ZPE to the dehydrogenation enthalpies of Ca(AlH(4))(2) and CaAlH(5) calculated by the direct method phonon analysis was compared to that calculated by the frozen-phonon method. The crystal structure of CaAlH(5) is presented in the more useful standard setting of P2(1)c symmetry and the phonon density of states of CaAlH(5), significantly different to other common complex metal hydrides, is rationalized.