Effect of surface viscosity on the vibration of microcantilevers

Using the theory of beam bending and the theory of surface rheology, the equation describing the effect of a surface viscous film on the vibration of an elastic microcantilever is derived. A generalized solution for the vibration of the microcantilever is obtained, which depends on the boundary conditions and the surface viscosity. There is a phase lag between the externally harmonic excitation and the microcantilever response due to the energy loss from surface flow. For small energy dissipation with negligible surface energy, the maximum energy loss occurs approximately at the natural frequencies of the microcantilever.     

紫杉醇微悬臂梁免疫传感器方法的研究

以巯基化的紫杉醇单抗修饰微梁镀金表面,制备了高灵敏的紫杉醇微悬臂梁免疫传感器.利用酶联免疫吸附测定方法对巯基化前后紫杉醇单抗的活性变化,以及巯基化单抗在微梁上的修饰进行检测与验证.采用紫杉醇微悬臂梁免疫传感器对不同浓度的紫杉醇溶液进行检测.结果表明:虽然巯基化后紫杉醇单抗的活性降低了18.6%,但巯基化紫杉醇单抗可以修...     

An anti E. coli O157:H7 antibody-immobilized microcantilever for the detection of Escherichia coli (E. coli).

A silicon microcantilever sensor was developed for the detection of Escherichia coli O157:H7. The microcantilever was modified by anti-E. coli O157:H7 antibodies on the silicon surface of the cantilever. When the aquaria E. coli O157:H7 positive sample is injected into the fluid cell where the microcantilever is held, the microcantilever bends upon the recognition of the E. coli O157:H7 antigen by the antibodies on the surface of the microcantilever. A negative control sample that does not contain E. coli O157:H7 antigen did not cause any bending of the microcantilever. The detection limit of the sensor was 1 x 10(6) cfu/mL when the assay time was < 2 h.     

Photochemical hydrosilylation of 11-undecenyltriethylammonium bromide with hydrogen-terminated Si surfaces for the development of robust microcantilever sensors for Cr(VI)

We report a novel approach to the design and development of microcantilever sensors in which photochemical hydrosilylation is used to modify the microcantilever surface. This process enables individual microcantilevers in multicantilever array chips to be modified separately by focusing the activating UV light sequentially on each particular cantilever. Photochemical hydrosilylation of 11-undecenyltriethylammonium bromide with hydrogen-terminated silicon microcantilever surfaces was carried out to yield a robust quaternary ammonium terminated organic monolayer suitable for chromate detection. The surface functionalities retain their affinity toward Cr(VI), and the organic monolayer is dense enough to generate significant surface stress upon subsequent adsorption of chromate ions from aqueous solutions.     

Improved surface modification approach for micromechanical biosensors

We have investigated the sensing performance of protein-based microcantilever biosensors prepared from multiple surface conjugation chemistries. The 11-mercaptoundecanoic acid monolayers were prepared according to both traditional and modified processes. In three protein-based biosensors, the modified process improved microcantilever sensing performance by increasing the bending amplitude, a critical step toward developing a cost-effective microcantilever-based sensor platform for medical diagnostics and environmental and drug screening applications. Scanning electron microscopy (SEM) images demonstrated that proteins immobilized on the microcantilever surface using the modified chemistry approach formed a compact layer.     

Nerve agents detection using a Cu2+/L-cysteine bilayer-coated microcantilever

A Cu2+/l-cysteine bilayer-coated microcantilever undergoes bending upon exposure to dimethyl methyl phosphonate at concentration as low as 10-15 M due to the complexation of a phosphonyl group with the Cu2+/l-cysteine bilayer on the microcantilever surface.     

Nanomechanics of the formation of DNA self-assembled monolayers and hybridization on microcantilevers

Biomolecular interactions over the surface of a microcantilever can produce its bending motion via changes of the surface stress, which is referred to nanomechanical response. Here, we have studied the interaction forces responsible for the bending motion during the formation of a self-assembled monolayer of thiolated 27-mer single-stranded DNA on the gold-coated side of a microcantilever and during the subsequent hybridization with the complementary nucleic acid. The immobilization of the single-stranded DNA probe gives a mean surface stress of 25 mN/m and a mean bending of 23 nm for microcantilevers with a length and thickness of about 200 microm and 0.8 microm, respectively. The hybridization with the complementary sequence could not be inferred from the nanomechanical response. The nanomechanical response was compared with data from well-established techniques such as surface plasmon resonance and radiolabeling, to determine the surface coverage and study the intermolecular forces between neighboring DNA molecules anchored to the microcantilever surface. From both techniques, an immobilization surface density of 3 x 10(12) molecules/cm(2) and a hybridization efficiency of 40% were determined. More importantly, label-free hybridization was clearly detected in the same conditions with a conventional sensor based on surface plasmon resonance. The results imply that the nanomechanical signal during the immobilization process arises mainly from the covalent attachment to the gold surface, and the interchain interactions between neighboring DNA molecules are weak, producing an undetectable surface stress. We conclude that detection of nucleic acid hybridization with nanomechanical sensors requires reference cantilevers to remove nonspecific signals, more sensitive microcantilever geometries, and immobilization chemistries specially addressed to enhance the surface stress variations.     

Transient deflection response in microcantilever array integrated with polydimethylsiloxane (PDMS) microfluidics

We report the integration of a nanomechanical sensor consisting of 16 silicon microcantilevers with polydimethylsiloxane (PDMS) microfluidics. For microcantilevers positioned near the bottom of a microfluidic flow channel, a transient differential analyte concentration for the top versus bottom surface of each microcantilever is created when an analyte-bearing fluid is introduced into the flow channel (which is initially filled with a non-analyte containing solution). We use this effect to characterize a bare (nonfunctionalized) microcantilever array in which the microcantilevers are simultaneously read out with our recently developed high sensitivity in-plane photonic transduction method. We first examine the case of non-specific binding of bovine serum albumin (BSA) to silicon. The average maximum transient microcantilever deflection in the array is -1.6 nm, which corresponds to a differential surface stress of only -0.23 mN m(-1). This is in excellent agreement with the maximum differential surface stress calculated based on a modified rate equation in conjunction with finite element simulation. Following BSA adsorption, buffer solutions with different pH are introduced to further study microcantilever array transient response. Deflections of 20-100 nm are observed (2-14 mN m(-1) differential surface stress). At a flow rate of 5 μL min(-1), the average measured temporal width (FWHM) of the transient response is 5.3 s for BSA non-specific binding and 0.74 s for pH changes.     

基于微悬臂梁生物传感器检测三磷酸腺苷

基于适配子构建了无标记检测三磷酸腺苷(ATP)的微悬臂梁生物传感器。 将ATP适配子修饰在微悬臂梁阵列中的传感悬臂镀金面上,用来识别ATP,而参比悬臂修饰巯基己醇(MCH)防止非特异性吸附。 ATP与其适配子发生特异性相互作用,使悬臂的上下两个表面产生应力差,导致传感悬臂产生偏转,扣除参比悬臂偏转后其偏转值与ATP的浓度在0.5~5 mmol/L范围内有良好的线性关系,相关系数为0.998,最低检出限为0.06 mmol/L。 该微悬臂梁生物传感器响应快速、操作简单,并且对ATP具有良好的特异性。     

The adsorption of dopamine on gold and its interactions with iron(III) ions studied by microcantilevers

The adsorption of dopamine (DA) molecules on gold and their interactions with Fe³⁺ were studied by a microcantilever in a flow cell. The microcantilever bent toward the Au side with the adsorption of DA due to the change of surface stress induced by the intermolecular hydrogen bonds of DA or the charge transfer effect between adsorbates and the substrate. The interaction process between DA adsorbates and Fe³⁺ was revealed by the deflection curves of microcantilever. As indicated by the appearance of a variation during the decline of curves, two steps were observed in the curve at relative high concentrations of Fe³⁺. In this case, Fe³⁺ reacted with DA molecules only in the outer layers and the complexes removed with solution. Then Fe³⁺ reacted further with DA molecules forming the surface complex in the first layer next to the gold. At this stage, the stability of surface complexes was time dependent, i.e., unstable initially and stable finally. This may be due to the surface complexes change from mono-dentate to bi-dentate complexes. In another case, i.e., at relative low concentration of Fe³⁺, only the first step was observed as indicated by the absence of a variation. X-ray photoelectron spectroscopy (XPS) and cycling voltammetry (CV) results provided complementary evidence for the result of microcantilever and proposal. As low as 5 × 10⁻¹⁰ M Fe³⁺ was detected by DA modified microcantilever with a good selectivity over other common metal ions.     

Label-free Microcantilever Immunosensor Based on a Competitive Immunoassay for the Determination of Clenbuterol

A label-free microcantilever immunosensor based on a competitive immunoassay is reported for the determination of clenbuterol. The immunosensor was fabricated by modifying clenbuterol–ovalbumin on the gold surface of the microcantilever with crossing linkage by L-cysteine and glutaraldehyde. Atomic force microscopy was utilized to characterize the construction of immunosensor and to measure the deflection of the microcantilever. The deflection response of the microcantilever was in negatively proportional to the concentration of clenbuterol from 1.0?×?10^?2 to 20?µg/L with a limit of detection of 1.0?×?10^?2?µg/L. The fabricated immunosensor was used to determine clenbuterol in pork samples with satisfactory results. In addition, the results were in accordance with those obtained by high-performance liquid chromatography. The reported immunosensor displayed high sensitivity and specificity together with excellent repeatability and reliability.     

Microcantilever biosensors based on conformational change of proteins

Microcantilevers (MCLs) hold a position as a cost-effective and highly sensitive sensor platform for medical diagnostics, environmental analysis and fast throughput analysis. MCLs are unique in that adsorption of analytes on the microcantilever (MCL) surface changes the surface characteristics of the MCL and results in bending of the MCL. Surface stress due to conformation change of proteins and other polymers has been a recent focus of MCL research. Since conformational changes in proteins can be produced through binding of anylates at specific receptor sites, MCLs that respond to conformational change induced surface stress are promising as transducers of chemical information and are ideal for developing microcantilever-based biosensors. The MCL can also potentially be used to investigate conformational change of proteins induced by non-binding events such as post-translational modification and changes in temperature or pH. This review will provide an overview of MCL biosensors based on conformational change of proteins bound to the MCL surface. The models include conformational change of proteins, proteins on membranes, enzymes, DNA and other polymers.     

Microcantilevers as gas‐phase sensing platforms: Simplification and optimization of the production of polymer coated porous‐silicon‐over‐silicon microcantilevers

The asymmetric roughening of silicon microcantilevers using different vapor stain‐etching conditions is studied with the aim of optimizing face selective coating of microcantilevers by polymers through simple dipping. The effect of roughening is studied by following the time‐dependent guest‐induced bending of silicone microcantilevers coated with a poly‐4‐vinylpyridine sensing layer. A correlation between the surface roughness of the microcantilevers and their time‐dependent guest‐induced bending is gained from combining high resolution scanning electron microscopy studies of the surface of the microcantilevers as well as their cross‐sections with time‐dependent guest‐induced microcantilever bending. The purpose of the present work is to lay the foundations for a small and relatively simple gas‐phase sensing tool based on a microcantilever platform capable of offering wide range sensing capabilities. © 2013 Wiley Periodicals, 2014 , 52, 141–146     

Redox-induced surface stress of polypyrrole-based actuators

We measure the surface stress induced by electrochemical transformations of a thin conducting polymer film. One side of a micromechanical cantilever-based sensor is covered with an electropolymerized dodecyl benzenesulfonate-doped polypyrrole (PPyDBS) film. The microcantilever serves as both the working electrode (in a conventional three-electrode cell configuration) and as the mechanical transducer for simultaneous, in situ, and real-time measurements of the current and interfacial stress changes. A compressive change in surface stress of about -2 N/m is observed when the conducting polymer is electrochemically switched between its oxidized (PPy+) and neutral (PPy0) state by cyclic voltammetry. The surface stress sensor's response during the anomalous first reductive scan is examined. The effect of long-term cycling on the mechanical transformation ability of PPy(DBS) films in both surfactant and halide-based electrolytes is also discussed. We have identified two main competing origins of surface stress acting on the PPy(DBS)/ gold-coated microcantilever: one purely mechanical due to the volume change of the conducting polymer, and a second charge-induced, owing to the interaction of anions of the supporting electrolyte with the gold surface.     

Optimization of DNA hybridization efficiency by pH-driven nanomechanical bending

The accessibility and binding affinity of DNA are two key parameters affecting the hybridization efficiency in surface-based biosensor technologies. Better accessibility will result in a higher hybridization efficiency. Often, mixed ssDNA and mercaptohexanol monolayers are used to increase the hybridization efficiency and accessibility of surface-bound oligonucleotides to complementary target DNA. Here, no mercaptohexanol monolayer was used. We demonstrate by differential microcantilever deflection measurements at different pH that the hybridization efficiency peaks between pH 7.5 and 8.5. At low pH 4.5, hydration and electrostatic forces led to tensile surface stress, implying the reduced accessibility of the bound ssDNA probe for hybridization. In contrast, at high pH 8.5, the steric interaction between neighboring ssDNA strands was decreased by higher electrostatic repulsive forces, bending the microcantilever away from the gold surface to provide more space for the target DNA. Cantilever deflection scales with pH-dependent surface hybridization efficiency because of high target DNA accessibility. Hence, by changing the pH, the hybridization efficiency is adjusted.     

Nanomechanical actuation driven by light-induced DNA fuel

We report the reversible nanomechanical actuation of a microcantilever driven by the light irradiation-induced conformational changes of i-motif DNA chains, which are functionalized on the cantilever's surface. It is shown that light irradiation-driven nanomechanical actuation can be manipulated using DNA hybridization and/or ionic concentrations.     

Highly sensitive and selective detection of beryllium ions using a microcantilever modified with benzo-9-crown-3 doped hydrogel

A microcantilever sensor modified by chitosan/gelatin hydrogels that are doped with benzo-9-crown-3 has been developed for the sensitive and selective detection of beryllium ions in an aqueous solution. The microcantilever undergoes bending deflection upon exposure to Be(2+) due to selective absorption of Be(2+) in the hydrogel. The detection limit is 10(-11) M. Other metal ions, such as Li(+), Na(+), K(+), Mg(2+), and Ca(2+), have a marginal effect on the deflection of the microcantilever. The mechanism of the bending is discussed and the results showed that the microcantilever may be used for in situ detection of beryllium.     

Thermodynamics of mechanical transduction of surface confined receptor/ligand reactions

Chemomechanics of surface stress is discussed in terms of interfacial thermodynamics. In the first section the paper shows how to quantitatively describe the chemical equilibrium of a receptor/ligand binding reaction confined at a solid-liquid interface and how the overall work of the reaction splits into chemical and surface work, that appears as a surface pressure. In the second section this thermodynamic model is applied to describe the experimental results of microcantilever bending induced by DNA hybridization occurring onto one of its faces.     

Application of a new microcantilever biosensor resonating at the air-liquid interface for direct insulin detection and continuous monitoring of enzymatic reactions

Here we describe the application of a recently developed high-resolution microcantilever biosensor resonating at the air-liquid interface for the continuous detection of antigen-antibody and enzyme-substrate interactions. The cantilever at the air-liquid interface demonstrated 50% higher quality factor and a 5.7-fold increase in signal-to-noise-ratio (SNR) compared with one immersed in the purified water. First, a label-free detection of a low molecular weight protein (insulin, 5.8 kDa) in physiological concentration was demonstrated. The liquid facing side of the cantilever was functionalized by coating its surface with insulin antibodies, while the opposite side was exposed to air. The meniscus membrane at the micro-slit around the cantilever sustained the liquid in the microchannel. After optimizing the process of surface functionalization, the resonance frequency shift was successfully measured for insulin solutions of 0.4, 2.0, and 6.3 ng ml(-1). To demonstrate additional application of the device for monitoring enzymatic protein degradation, the liquid facing microcantilever surface was coated with human recombinant SOD1 (superoxide dismutase 1) and exposed to various concentrations of proteinase K solution, and the kinetics of the SOD1 digestion was continuously monitored. The results showed that it is a suitable tool for sensitive protein detection and analysis.     

Micromechanical measurement of AChBP binding for label-free drug discovery

A potential binding assay based on binding-driven micromechanical motion is described. Acetylcholine binding protein (AChBP) was used to modify a microcantilever. The modified microcantilever was found to bend on application of the naturally occurring agonist (acetylcholine) or the antagonist (nicotine and d-tubocurarine). Control experiments show that microcantilevers modified without AChBP do not respond to acetylcholine, nicotine, and d-tubocurarine. K(d) values obtained for acetylcholine, nicotine, and d-tubocurarine are similar to those obtained from radio-ligand binding assays. These results suggest that the microcantilever system has potential for use in label free, drug screening applications.