利用质量流注入的流激孔腔噪声共振峰抑制

通过数值仿真揭示了开口前缘垂直注入质量流和前壁面平行注入质量流抑制流激孔腔噪声的机制,研究了多参数影响下脉动压力峰值降噪量和总降噪量随质量流注入速度的变化规律。开口前缘垂直注入质量流通过抬升剪切层,避免漩涡冲击开口后缘,抑制流激孔腔噪声脉动压力峰值;在一定范围内质量流注入速度越大,脉动压力峰值降噪量越大,但是低频部分引起的抬升也会越高,导致总降噪量先增大后减小;经优化后的峰值降噪量和总降噪量分别可以达到15dB和9.5dB。开口前壁面平行注入质量流则是通过加强开口处剪切层的稳定性,避免发生漩涡脱落,达到抑制流激孔腔噪声的目的;当质量流入口面积大于孔腔开口前壁面积2/3时,不仅可以显著降低流激孔腔噪声脉动压力的峰值,并且可以很好地抑制其它频段噪声的抬升;质量流注入速度为来流速度的0.5倍时,脉动压力峰值降噪量和总降噪量分别可以达到18dB和15.4dB。     

水下流激孔腔噪声前馈有源控制实验研究

水流流经腔体时引起的自激振荡会形成流激噪声,该文通过仿真和实验研究了水下流激孔腔噪声的主动声场控制。应用有源前馈控制方法,对比了参考信号的选取以及控制器中增加的泄露因子对控制结果的影响,并在水循环管路中对流激孔腔噪声前馈控制效果进行了实验验证。研究结果表明,前馈有源噪声控制方法可有效抑制水下流激孔腔噪声,在误差点和辅助观测点都取得了良好的降噪效果,最大降噪量大于8 dB,并且使用腔内信号作为参考的控制效果优于上游信号作为参考。     

开孔结构流致噪声的数值模拟和机理分析

飞机机体表面的开孔设计会形成空腔结构,产生空腔流致噪声。空腔噪声的控制需要彻底认识其流动和噪声机理。以飞机的功能性开孔为例,通过半经验公式分析了其空腔噪声频率随速度的变化规律,预测了出现流声共振的工况。空腔发生流声共振时,特定频率的纯音噪声会被放大。为此,采用脱体涡模拟方法开展了开孔结构流声共振的三维非定常数值计算,分析了其流场和声场特性。其中,数值方法的准确性通过圆形空腔标模计算进行验证。结果表明,在一定速度下剪切层内的扰动将诱发空腔深度方向声模态,出现流声共振现象。此时,剪切层表现为强烈的周期性上下拍动,空腔底部和后缘区域的局部压力脉动幅值较大,声波主要由空腔后缘向上游方向辐射,上游噪声大于下游。     

水下充水圆柱声腔内声场自适应有源控制实验研究

本文研究了有限长充水圆柱置于水中，外声场透射形成的腔内声场自适应有源控制实验研究，结果显示，由于圆柱结构与水介质的耦合，有源控制中的声控制方法能够较好的抵消声腔主导模态和强耦合的结构主导模态，因而能够抵消在圆柱腔内较宽频带范围的声场，实验还研究了消声频带，误差传感器布放位置及肖声区域等问题。     

利用共振无源腔分析和抑制飞秒脉冲激光噪声的理论和实验研究

理论分析了共振无源腔对飞秒脉冲激光的强度和相位噪声的转化模型,分析表明,通过测量无源腔透射场或者反射场相对于输入场强度噪声的变化,可以间接得到输入场飞秒脉冲激光的相位噪声.在此基础上设计了精细度约为1500、自由光谱区为75 MHz的八镜环形共振无源腔,并测量了钛宝石锁模激光经过该共振无源腔后透射场和反射场强度噪声的变化.实验观察到,飞秒脉冲激光经过无源腔透射后,强度噪声特性得到较好改善,在探测频率2 MHz附近达到散粒噪声极限.同时,结合共振无源腔对激光强度和相位噪声的转化模型,间接给出了钛宝石锁模激光的相位噪声及无源腔对相位噪声的有效抑制作用.     

Active control of aircraft fly-over sound transmission through an open window

This paper presents an experimental work on active control of sound transmission through a restricted opening bottom hinged window. The main goal of the work is to demonstrate the feasibility of the active technique to limit the loss of attenuation due to the aperture of windows, and its application to aircraft fly-over incident noise. The experimental window is placed in an exposed façade of a dwelling close to an airport and subject to fly-by aircraft noise. The active control is configured to cancel the pressure at the aperture using a single-input single-output feedforward adaptive system. As a result, a reduction of sound transmission is achieved with low power consumption. In global terms, an increase of almost 3 dB of transmission loss (with respect to the partially opened window insulation values) in the low frequency range (below 160 Hz and according to the National Danish Method for evaluating low frequency noise) is demonstrated, which is equivalent to a reduction of 50% in the loss of insulation caused by opening the window.     

Improving performance of FxRLS algorithm for active noise control of impulsive noise

Active noise control (ANC) systems employing adaptive filters suffer from stability issues in the presence of impulsive noise. New impulsive noise control algorithms based on filtered-x recursive least square (FxRLS) algorithm are presented. The FxRLS algorithm gives better convergence than the filtered-x least mean square (FxLMS) algorithm and its variants but lacks robustness in the presence of high impulsive noise. In order to improve the robustness of FxRLS algorithm for ANC of impulsive noise, two modifications are suggested. First proposed modification clips the reference and error signals while, the second modification incorporates energy of the error signal in the gain of FxRLS (MGFxRLS) algorithm. The results demonstrate improved stability and robustness of proposed modifications in the FxRLS algorithm. However, another limitation associated with the FxRLS algorithm is its computationally complex nature. In order to reduce the computational load, a hybrid algorithm based on proposed MGFxRLS and normalized step size FxLMS (NSS-FXLMS) is also developed in this paper. The proposed hybrid algorithm combines the stability of NSS-FxLMS algorithm with the fast convergence speed of the proposed MGFxRLS algorithm. The results of the proposed hybrid algorithm prove that its convergence speed is faster than that of NSS-FxLMS algorithm with computational complexity lesser than that of FxRLS algorithm.     

Performance of an independent planar virtual sound barrier at the opening of a rectangular enclosure

Planar virtual sound barrier systems have been used successfully to reduce noise radiation through an opening without affecting natural ventilation and lighting. However, the complexity of a fully coupled control system grows at the rate proportional to the square of the number of channels and this make the system implementation become impractical for enclosures with large openings. To reduce the system complexity, this paper proposes an independent planar virtual sound barrier, which is a multi-channel system consisting of many independent single channel active noise control systems. Each single channel system is “independent” in the sense that the control source output of the system is updated only with the signal from its own error sensor. Based on the analytical model of sound radiation through the opening of a rectangular enclosure, the transfer functions from both primary and control sources are calculated first. Then the noise reduction performance, the stability, and the convergence behavior of both fully coupled and independent planar virtual sound barrier systems are investigated. It is found that the independent system with no control output constraint becomes inherently unstable at some frequencies; however its stability can be improved by applying some control output constraint. Reducing the number of channels and the distance between secondary loudspeakers and error microphones can also increase system stability but at the cost of smaller noise reduction. When the system is inherently stable and there is no constraint on control output, the independent system can provide the same noise reduction as the fully coupled one but with faster convergence speed.     

Simulation study on active noise control for a 4-T MRI scanner

The purpose of this work is to study computationally the possibility of the application of a hybrid active noise control technique for magnetic resonance imaging (MRI) acoustic noise reduction. A hybrid control system combined with both feedforward and feedback loops embedded is proposed for potential application on active MRI noise reduction. A set of computational simulation studies were performed. Sets of MRI acoustic noise emissions measured at the patient's left ear location were recorded and used in the simulation study. By comparing three different control systems, namely, the feedback, the feedforward and the hybrid control, our results revealed that the hybrid control system is the most effective. The hybrid control system achieved approximately a 20-dB reduction at the principal frequency component. We concluded that the proposed hybrid active control scheme could have a potential application for MRI scanner noise reduction.     

Active control of intermittent noise in a room

I.IntroductionThereverberantnoisesmaybereducedwithanactivenoisecontrol(ANC)systcmformedbyacornermicrophonc-amplifier-1oudspcakersystemina.oom.lllThismeth-odbascdonthenormalmodccancelingprincip1chasalreadybeenclarifiedbothinthco-ryandexperimcnts,andthclimitationandpotcntialityofitsapp1icationalsodiscussedinapreviouspaper.Thediscussionsinthepastlimitedmost1ytothesteadyconditionofnoiscfield,andthisisextendedtothetransientcondihoninthcprcsentwork,viz.thein-llucnceofthecornerANCsystemwhenthenois…     

An empirical model for the noise propagation in open cast mines - A case study

Data obtained from 312 measurement stations of sound propagation in panel 48 of the Tuncbilek open cast mine, Western Lignite Corporation, Turkey have been used to create an empirical model for such propagation. As well as the noise level recorded at these stations, atmospheric conditions were recorded also by the meteorological station located at the same panel. A total of 95,000 noise values were recorded at these stations. In addition the distances of the measurement stations to the effective source of noise and to the working slope, the meteorological effects and the number of noise sources were defined for each of 312 measurement stations. Using these data, the proposed model was tested against the noise measurements.     

Active noise control in a duct by an analog neural network circuit

Conventional active noise control (ANC) in ducts has been realized with digital signal processing. The physical size of the conventional ANC systems is usually large owing to the signal processing interval, and the cost of the system depends on the price of the digital signal processor (DSP). This paper proposes a new ANC system with an analog neural network circuit, which will process signals in short time periods without DSP. The proposed neural network circuit has a simple structure consisting of analog multipliers and an integrator, and we simulated the performance of the circuit by HSPICE. We also fabricated a circuit connected to a real duct and confirmed operation of the proposed ANC system.     

Hybrid active and passive control of fan noise

This paper deals with the global reduction of axial flow fan noise in ducts in a building using a hybrid passive-active noise control method. The effectiveness of using an infra-red device as a reference signal source is also investigated. It is shown that using such a hybrid noise control system over an axial-flow fan reduces the overall sound pressure level by 5 dB(A) in the surrounding environment and global control of the blade passing frequency can also be achieved. This paper also shows that using an infra-red device as a reference signal source produces marginally better control as compared with using a microphone reference sensor. Moreover, long term stability is guaranteed and the possibility of acoustic feedback is eliminated.     

主动噪声控制声学通道的实验辨识

传统的自适应滤波器不能直接用于主动噪声控制，因为扬声器和误差传声器之间的声学通道可能使系统不稳定。本文根据声学通道的相应特性，建立补偿滤波器，提出了用实验方法辨识声学通道传输特性。在房间实验中研究了单通道相位因子的变化特性，并进一步用于飞机人多通道主动噪声控制，给出了相应的实验结果。     

调节水床效应的双梯度有源噪声控制自适应算法*

为了使自适应反馈有源噪声控制系统能够兼顾水床效应,通过约束次级信号的能量以调节噪声放大,设计了一种双梯度算法。当次级信号满足约束,算法沿着最小化误差信号能量的梯度方向迭代,反之,则沿着最小化次级信号能量的方向迭代。在有源降噪耳机实例中的对比结果表明,该算法能调节噪声放大并保持较大的降噪带宽,且运算量没有显著增加。     

一种调节反馈有源噪声控制系统水床效应的频域自适应算法*

伯德灵敏度积分决定反馈有源控制系统具有水床效应,即某个频段内的噪声衰减伴随着另一频段内的噪声放大。已有的反馈系统自适应算法没有明确考虑噪声放大量,非自适应算法考虑了噪声放大量但不能在线调整。为了使自适应反馈系统能明确调节噪声放大量,该文以控制器某个频段内的幅度响应小于指定阈值为约束条件,并作为"惩罚项"与误差信号能量相加得到代价函数,通过最速下降法最小化该代价函数得到了一种频域自适应算法。与已有算法在有源降噪耳机实例中的对比结果表明,该算法能够更为直接地对指定频段内的噪声放大量进行调节,从而在降噪量与噪声放大量之间取得折衷。     

A compound secondary source for active noise radiation control

Based on the analysis of active noise control system with multi-channel monopole secondary sources, a kind of compound secondary source is proposed in this paper. The proposed compound secondary source consists of two closely located monopole sources with their distance much smaller than a wavelength. The characteristics of the compound source are analyzed, and the performances of the active noise control system with the compound secondary sources on the monopole primary sound field and sound radiated by a plate are investigated both numerically and experimentally. It has been found that the proposed compound secondary sources control system can provide higher noise reduction for free field noise radiation control with the same number of control channels. It is shown that the better performance in noise reduction of the compound secondary sources control system is mainly due to the directivity of the secondary sources where the energy radiation pattern of the compound sources is similar to that of the primary sources.     

应用于有源声辐射控制的一种组合次级声源

在分析多通道单极子次级源控制系统的基础上,提出一种幅度调节型组合次级声源,这种组合源由两个单极子声源构成,单极子声源的间距远小于声波的波长。文中就组合次级源在自由场中对不同初级声源辐射噪声的控制进行理论分析和实验验证,并与同等条件下的单极子次级源控制系统的降噪性能进行了比较分析。数值计算和实验结果均表明,对于不同的初级声场,在次级通道数相同的情况下,组合次级源控制系统可以得到比单极子次级源控制系统高的降噪量。     

Passive and active interior noise control of box structures using the structural intensity method

This paper presents passive and active vibro-acoustic noise control methods for attenuating the interior noise level in box structures which can be an analogy of cabins of vehicle and aircraft. The structural intensity (SI) approach is adopted to identify the predominant vibration panels and interior noise sources for box structures. In the study, the finite element method is used to determine the structural vibration and structural intensity in the box surfaces. According to structural intensity vectors plot and structural intensity stream lines presentation, the possible effective control positions where the dampers may be attached and the active control forces may act to reduce vibration and interior noise, are identified. From the study, it can be demonstrated that the structural intensity approach and stream line presentation are possible methods for identifying the vibro-acoustic interior noise source and predominant panels which may be modified to reduce the interior noise level. The structural intensity methodology, passive and active noise control results can be extended to the further study of the vibration and interior noise control of actual cabins of vehicles and aircraft.     

Design and experimental tests of active control barriers for low-frequency stationary noise reduction in urban outdoor environment

Active noise control (ANC) techniques are based on the emission of an antiphase signal in order to cancel the noise produced by a primary source. ANC has been successfully applied especially for reducing noise in confined environments, such as headphones and ducts. In this study, we present an application of ANC concepts to the design of an anti-noise barrier for an outdoor environment and its experimental testing. Even though passive techniques are effective in noise reduction at middle-high frequencies, they become less efficient at low frequencies (below 300 Hz) due to the limited dimensions of commonly deployable barriers. In this paper, we analyze the properties of a low-cost active noise system able to efficiently operate on stationary, almost pure-tone, low-frequency noise, such as that produced by electrical transformers and reactors in power and transformation plants. A prototype has been implemented and on-the-field experimental tests have been carried out. The results (confirmed also by numerical simulations) demonstrate a remarkable efficiency in the far field, with a reduction up to 15 dB with respect to the absence of the ANC system.