Wet effluent diffusion denuder technique and determination of volatile organic compounds in air. I. Oxo compounds (alcohols and ketones)

The wet effluent diffusion denuder (WEDD) preconcentration technique for the determination of methanol, ethanol, 1-propanol, 2-propanol, 1-butanol, 1-pentanol, acetone, methyl ethyl ketone, diethyl ketone and methyl n-propyl ketone in air is discussed. The compounds are continuously collected into a thin film of deionized water flowing down the inner wall of the cylindrical wet effluent diffusion denuder. The concentrate is analysed by gas chromatography. Detection limits of alcohols and ketones are as low as 1 microg/l (GC-flame ionization detection) and/or 1 ng/l (GC-MS). This technique could be applicable for the continuous monitoring of ppb (v/v) levels of both alcohols and ketones in the air.     

吹扫捕集GC-MS法测定水中的丙酮和丁酮

建立吹扫捕集气相色谱-质谱法测定水中丙酮和丁酮的检测方法。对吹扫捕集条件进行优化,吹扫温度为20℃,吹扫时间为11 min,脱附温度为245℃,脱附时间为2 min。在全扫描模式下进行定性分析,在选择性离子扫描模式下进行定量分析。在优化实验条件下,丙酮和丁酮的质量浓度在5~200μg/L范围内与其响应值呈良好线性关系(r~2≥0.990),检出限分别为0.01,0.05μg/L,加标回收率分别为100.8%~116.9%,84.5%~101.4%,测定结果的相对标准偏差分别为0.94%~4.83%,0.67%~2.69%(n=6)。该方法检出限低,精密度、准确度高,适用于生活饮用水、地表水、地下水、生活污水和工业废水中丙酮和丁酮的分析。     

Multivariate optimization of a solid phase microextraction-headspace procedure for the determination of benzene, toluene, ethylbenzene and xylenes in effluent samples from a waste treatment plant

A method based on solid-phase microextraction (SPME) and gas chromatography with flame ionization detection (GC-FID) has been optimized for the determination of benzene, toluene, ethylbenzene and xylenes (BTEX) in water released from a waste treatment plant. The extraction step was optimized using fractional factorial and central composite designs including the following experimental factors: saline concentration; extraction time; desorption time; agitation velocity; headspace volume. A multiple function was used to describe the experimental conditions for simultaneous extraction of the compounds. The procedure, based on direct SPME at 50 degrees C, using a polydimethylsiloxane fiber, showed good linearity (r>0.997 over a concentration range 2-200 microg L(-1)) and repeatability (relative standard deviation (RSD)<4.23%) for all compounds, with limits of detection ranging from 0.05 to 0.28 microg L(-1), and limits of quantification ranging from 0.14 to 0.84 microg L(-1). Concentrations of the target compounds in these samples were between 145.8 and 1891 microg L(-1).     

Recognition of alkyl ketone molecules based on thickness-shear-mode acoustic sensors with calixarene derivatives

The frequency response characteristics for twenty-two organic vapours by piezoelectric thickness-shear-mode (TSM) acoustic wave sensors coated with four supramolecule compounds—calixarenes have been investigated. Among them, 2,8,14,20-tetraethyl-4,6,10,12,16,18,22,24-octahydroxylcalix[4]arene (I) was the most efficient actively adsorptive material for host-guest recognizing alkyl ketone molecules such as 2-butanone and acetone. The supramolecule recognition mechanism has been discussed, that is based on the formation of C-H?π bond interaction between the methyl group of ketone molecule and the phenyl ring of the calixarene compound. The linear range of the TSM sensor upon exposure to 2-butanone vapour was 0-940.5 ppm with a detection limit of 2.67 ppm when the coating mass of the compound I was selected as 19 μg. The kinetics behaviours in the adsorption and desorption processes have been examined with polynomial curve fitting procedure. Furthermore, the proposed TSM sensor possessed good selectivity, reversibility, reproducibility and high stability. Compared with gas chromatography (GC) method, the proposed sensor can be used for on-line determination of 2-butanone vapour in air with a recovery of 94.8-106.5%, which was in consistent with those obtained by GC method.     

Development and validation of a rapid headspace gas chromatography-mass spectrometry method for the determination of diethyl ether and acetone residues in Tween extracts of shellfish intended for mouse bioassay for diarrhoetic toxins

A validated analytical method using headspace capillary gas chromatography with mass spectrometric detection, which utilises deuterated analogues of the target analytes as internal standards has been developed and applied to the determination of acetone and diethyl ether in Tween extracts of cockles (Cerastoderma edule) and mussels (Mytilus edulis) destined for mouse bioassay for lipophilic toxins. The optimal conditions for headspace incubation were 50 degrees C for 6 min. The limits of detection and quantitation for both DEE and acetone were 2 and 7 microg/mL, respectively, based on signal to noise ratios of 3 and 10, respectively. The linear dynamic range of the instrument was 0 to ca. 4000 microg/mL for both acetone (r(2)=0.995) and DEE (r(2)=0.999). Tween extracts of cockle spiked with acetone and DEE at 3925 and 3570 microg/mL, respectively, gave mean (n=3) recovery figures of 101% (RSD=13.1%) for acetone and 90% (RSD=7.3%) for DEE in cockle matrix. The corresponding figures obtained from spiked mussel matrix were 114% (RSD=5.7%) for acetone and 95% (RSD=6.7%) for DEE, respectively, which were within acceptable range.     

Negative ion chemical ionization GC/MS-MS analysis of dialkylphosphate metabolites of organophosphate pesticides in urine of non-occupationally exposed subjects

Low level exposure to organophosphate (OP) pesticides can be determined by the measurement of dialkylphosphate (DAP) metabolites in urine. An analytical method is presented here which can measure the metabolites dimethyl phosphate (DMP), diethyl phosphate (DEP), dimethyl thiophosphate (DMTP), dimethyl dithiophosphate (DMDTP), diethyl thiophosphate (DETP), and diethyl dithiophosphate (DEDTP) at low levels. This was achieved by lyophilization of the urine, derivatization with pentafluorobenzyl bromide (PFBBr) and quantification by negative ion chemical ionization GC/MS-MS. The detection limits for the metabolites were 0.5 microg L(-1) DMP, 0.1 microg L(-1) DEP, 0.1 microg L(-1) DMTP, 0.04 microg L(-1) DMDTP, 0.04 microg L(-1) DETP and 0.02 microg L(-1) DEDTP. The RSD for the analytical method was 4-14% for the six metabolites. The method was used to monitor a group of non-occupationally exposed individuals in Sydney, Australia. The metabolites DMP, DEP, DMTP, DMDTP, DETP and DEDTP occurred in 73, 77, 96, 48, 100 and 2% of the samples with median values of 13, 3, 12, <1, 1 and 1 microg L(-1) respectively. The method is simple to use, sensitive and suitable for routine analysis of non-occupational exposure levels. These detection limits are between one and two orders of magnitude lower than those previously reported in the literature.     

Flow-injection determination of ornidazole by chemiluminescence detection based on a luminol-ferricyanide reaction.

A flow-injection analysis (FIA) with a chemiluminescence detection method was developed for the determination of ornidazole based on the inhibition intensity of chemiluminescence from the luminol-ferricyanide system. Under the condition of 1.0 x 10(-3) mol/L luminol and 5.0 x 10(-6) mol/L potassium ferricyanide, the response to the concentration of omidazole is linear from 0.2 microg ml(-1) to 10 microg ml(-1), and a detection limit of 0.05 microg ml(-1) can be obtained. This method has been successfully applied to the determination of omidazole in pharmaceutical preparations.     

Development of a novel method based on liquid chromatography-evaporative light scattering detection for the direct determination of streptomycin and dihydrostreptomycin in raw materials, pharmaceutical formulations, culture media and plasma

A novel method for the non-derivatization liquid chromatographic determination of streptomycin (STR) and dihydrostreptomycin (DHSTR) was developed and validated based on evaporative light scattering detection (ELSD). Utilizing a ThermoHypersil BetaBasic C18 analytical column, evaporation temperature of 50 degrees C and pressure of nebulizing gas (nitrogen) of 3.5 bar, the optimized mobile phase was 1.25 mL L(-1) TFA aqueous solution, in an isocratic mode at a rate of 1.0 mL min(-1). STR was eluted at 5.6 min and DHSTR at 7.8 min with a resolution of 4.4. Linear calibration curves were obtained from 2 to 120 microg mL(-1) (r > 0.9990) for STR and 2-75 microg mL(-1) (r > 0.9994) for DHSTR, with a LOD equal to 0.7 and 0.5 microg mL(-1), respectively. The developed method was applied for the assay of STR and DHSTR (sulfate) in pharmaceutical raw materials and formulations, while the simultaneous direct determination of sulfate was feasible (tR = 2.5 min, LOD = 1.4 microg mL(-1), double logarithmic calibration curve in the range of 4-50 microg mL(-1), r > 0.9998). Modified isocratic mobile phase (H2O-ACN, 90:10, v/v, containing 1.25 mL L(-1) TFA), was used for the determination of streptomycin B impurity in STR sulfate raw material and a gradient mobile phase (H2O-ACN containing TFA) was used for the determination of DHSTR in the presence of penicillinG procaine. The developed method was also applied for the assay of commercial formulations (STR powder and DHSTR injection solution and suspension) (%recovery 98-102, %RSD < 1.3, n = 3 x 3), for the determination of STR in bacteria culture medium (%recovery 99.6, %RSD = 0.8, n = 3 x 3), and for the determination of DHSTR in human plasma (2.0-23.0 microg mL(-1)) after solid phase extraction using carboxylate cartridges (%recovery 98.4-101.8, %RSD = 3.2, n = 3 x 3).     

Screening of citalopram, fluoxetine and their metabolites in human urine samples by gas chromatography-mass spectrometry. A global robustness/ruggedness study

Capillary gas chromatography with mass spectrometry detection in SIM mode (GC-MS-SIM) has been used for the analysis of citalopram (CIT), fluoxetine (FLX), and all of their metabolites in urine samples. The instrumental parameters affecting GC separation and MS-SIM detection were investigated. A validation procedure was performed on urine matrix and a simultaneous robustness/ruggedness evaluation is also presented in this paper. An optimized solid-phase extraction (SPE) has been applied, reaching in this way to limits of detection (LODs) between 0.7 ng L(-1) (CIT) and 33.6 microg L(-1) (CIT-PA). A pharmacokinetic screening in clinical urine samples has been also carried out.     

Acetone adsorption on ice surfaces in the temperature range T = 190-220 K: evidence for aging effects due to crystallographic changes of the adsorption sites

The rate and thermodynamics of the adsorption of acetone on ice surfaces have been studied in the temperature range T = 190-220 K using a coated-wall flow tube reactor (CWFT) coupled with QMS detection. Ice films of 75 +/- 25 microm thickness were prepared by coating the reactor using a calibrated flow of water vapor. The rate coefficients for adsorption and desorption as well as adsorption isotherms have been derived from temporal profiles of the gas phase concentration at the exit of the flow reactor together with a kinetic model that has recently been developed in our group to simulate reversible adsorption in CWFTs (Behr, P.; Terziyski, A.; Zellner, R. Z. Phys. Chem. 2004, 218, 1307-1327). It is found that acetone adsorption is entirely reversible; the adsorption capacity, however, depends on temperature and decreases with the age of the ice film. The aging effect is most pronounced at low acetone gas-phase concentrations (< or = 2.0 x 10(11) molecules/cm(3)) and at low temperatures. Under these conditions, acetone is initially adsorbed with a high rate and high surface coverage that, upon aging, both become lower. This effect is explained by the existence of initially two adsorption sites (1) and (2), which differ in nature and number density and for which the relative fractions change with time. Using two-site dynamic modeling, the rate coefficients for adsorption (k(ads)) and desorption (k(des)) as well as the Langmuir constant (K(L)) and the maximum number of adsorption sites (c(s,max)), as obtained for the adsorption of acetone on sites of types (1) and (2) in the respective temperature range, are k(ads)(1) = 3.8 x 10(-14) T(0.5) cm(3) s(-1), k(des)(1) = 4.0 x 10(11) exp(-5773/T) s(-1), K(L) (1) = 6.3 x 10(-25) exp(5893/T) cm(3), c(s,max)(1) < or = 10(14) cm(-2) and k(ads)(2) = 2.9 x 10(-15) T(0.5) cm(3) s(-1), k(des)(2) = 1.5 x 10(7) exp(-3488/T) s(-1), K(L)(2) = 5.0 x 10(-22) exp(3849/T) cm(3), c(s,max)(2) = 6.0 x 10(14) cm(-2), respectively. On the basis of these results, the adsorption of acetone on aged ice occurs exclusively on sites of type (2). Among the possible explanations for the time-dependent two-site adsorption behavior, i.e., crystallographic differences, molecular or engraved microstructures, or a mixture of the two, we tentatively accept the former, i.e., that the two adsorption sites correspond to cubic (1, I(c)) and hexagonal (2, I(h)) sites. The temporal change of I(c) to I(h) and, hence, the time constants of aging are consistent with independent information in the literature on these phase changes.     

气相色谱法测定工作场所空气中正己烷、丙酮、丁酮和乙酸丁酯的含量

用气相色谱法对空气中正己烷、丙酮、丁酮和乙酸丁酯的含量进行测定。采用活性炭管采集了空气中的正己烷、丙酮、丁酮和乙酸丁酯,采用二硫化碳进行解吸,用Agilent 19091N-216HP-INNOWAX Polyethylene Glycol毛细管色谱柱分离,氢焰离子化检测器检测。正己烷、丙酮、丁酮和乙酸丁酯的检出限(3S/N)为0.43,0.30,0.44,1.7mg.L-1。方法的解吸率在86.7%～100.3%之间,相对标准偏差(n=6)在1.97%～3.89%之间。     

Diverse structures and adsorption properties of quasi-Werner-type copper(II) complexes with flexible and polar axial bonds

The quasi-Werner-type copper(II) complex, [Cu(PF(6))(2)(4-mepy)(4)] (1), in which 4-mepy is the 4-methylpyridine ligand, has flexible and polar axial bonds of Cu-PF(6). Flexibility of the Cu-PF(6) bonds induces diverse and unprecedented guest-inclusion structures, such as {[Cu(PF(6))(2)(4-mepy)(4)][Cu(PF(6))(4-mepy)(4)(acetone)]·PF(6)·4acetone} (γ-1?2.5acetone), {[Cu(PF(6))(2)(4-mepy)(4)][Cu(PF(6))(4-mepy)(4)(2-butanone)]·PF(6)·3.5(2-butanone)} (γ-1?2.25(2-butanone)), {[Cu(PF(6))(2)(4-mepy)(4)][Cu(PF(6))(4-mepy)(4)(H(2)O)]·PF(6)·4benzene} (γ-1?0.5H(2)O·2benzene), and {[Cu(PF(6))(2)(4-mepy)(4)]·2benzene} (γ-1?2benzene). Exposure of the dense form, α-1, to benzene vapor affords the benzene-inclusion complex {[Cu(PF(6))(2)(4-mepy)(4)]·2benzene} (γ-1?2benzene), all benzene guests of which are easily removed by vacuum drying, reforming guest-free, dense α-1' with smaller sized crystals than α-1. In contrast to α-1, which shows almost no CO(2) adsorption, α-1' adsorbs CO(2) gas with structural transformations, this being the first example that exhibits adsorption of gas in a dense Werner-type complex and a drastic change in adsorption properties depending on the size of the crystals.     

Simple, sensitive, selective and validated spectrophotometric methods for the estimation of a biomarker trigonelline from polyherbal gels

Simple, accurate, reproducible, selective, sensitive and cost effective UV-spectrophotometric methods were developed and validated for the estimation of trigonelline in bulk and pharmaceutical formulations. Trigonelline was estimated at 265 nm in deionised water and at 264 nm in phosphate buffer (pH 4.5). Beer's law was obeyed in the concentration ranges of 1-20microg mL(-1) (r2=0.9999) in deionised water and 1-24 microg mL(-1) (r2=0.9999) in the phosphate buffer medium. The apparent molar absorptivity and Sandell's sensitivity coefficient were found to be 4.04 x 10(3)L mol(-1)cm(-1) and 0.0422 microg cm(-2)/0.001A in deionised water; and 3.05 x 10(3)L mol(-1)cm(-1) and 0.0567 microg cm(-2)/0.001A in phosphate buffer media, respectively. These methods were tested and validated for various parameters according to ICH guidelines. The detection and quantitation limits were found to be 0.12 and 0.37 microg mL(-1) in deionised water and 0.13 and 0.40 microg mL(-1) in phosphate buffer medium, respectively. The proposed methods were successfully applied for the determination of trigonelline in pharmaceutical formulations (vaginal tablets and bioadhesive vaginal gels). The results demonstrated that the procedure is accurate, precise, specific and reproducible (percent relative standard deviation <2%), while being simple and less time consuming and hence can be suitably applied for the estimation of trigonelline in different dosage forms and dissolution studies.     

A liquid-phase microextraction method, combining a dual gauge microsyringe with a hollow fiber membrane, for the determination of organochlorine pesticides in aqueous solution by gas chromatography/ion trap mass spectrometry

A liquid-phase microextraction (LPME) method has been demonstrated for the extraction and determination of organochlorine pesticides (OCPs) in aqueous solution. The method combines a dual gauge microsyringe with a hollow fiber membrane (LPME/DGM-HF) followed by detection by gas chromatography/ion trap mass spectrometry (GC/ITMS). The advantages include speed, low solvent and sample consumption, simplicity and ease of use. The extraction time, solvent selection, salt concentration and sample stirring rate have been investigated in order to optimize extraction efficiency. The viability is evaluated by measuring the linearity and detection limit of the five OCPs in aqueous solution. Detection linearity for the OCPs has been achieved over a range of concentrations between 1 and 500 microg/L (r2 > 0.930), with a detection limit of 0.1 microg/L for each OCP.     

Solid-phase synthesis of a combinatorial array of 1,3-bis(acylamino)-2-butanones, inhibitors of the cysteine proteases cathepsins K and L

To more rapidly prepare members of the 1,3-bis(acylamino)-2-butanone class of cysteine protease inhibitors, a solid-phase synthesis was developed. 1-Azido-3-amino-2,2-dimethoxybutane (4), which has the two amino groups differentiated and the ketone protected as a a ketal, served as a surrogate for the 1,3-diamino-2-butanone core. Amine (4) was coupled to the BAL-resin-linked carboxylic acids derived from alpha-amino acid esters. Evaluation of a small combinatorial array by measuring inhibition constants (Ki,appS) against cathepsins K, L, and B provided some structure-activity relationship trends with respect to selectivity and potency. Novel, potent inhibitors of cathepsins K and L were identified.     

Analysis of tobacco-specific N-nitrosamines in snuff by ethyl acetate extraction and liquid chromatography-tandem mass spectrometry

A rapid, selective and sensitive method for routine analysis of the four tobacco-specific N-nitrosamines, N'-nitrosonornicotine, N'-nitrosoanatabine, N'-nitrosoanabasine and 4-(methyl-nitrosamino)-1-(3-pyridyl)-1-butanone in snuff has been developed. The nitrosamines were isolated by ethyl acetate extraction and analysed by LC-MS-MS. Except for evaporation and filtration, no additional clean-up steps are needed in the proposed method. The detection limits for standard in solvent are between 0.0005 and 0.001 microg/ml (0.005 and 0.01 microg/g).     

Solid phase extraction and spectrophotometric determination of silver with 2-(2-quinolylazo)-5-diethylaminophenol as chromogenic reagent.

A new chromogenic reagent, 2-(2-quinolylazo)-5-diethylaminophenol (QADEAP), was synthesized. A sensitive, selective and rapid method has been developed for the determination of microg/L level silver ion based on the rapid reaction of silver(l) with QADEAP and the solid phase extraction of the colored chelate with C18 cartridge. The QADEAP reacts with Ag(l) to form a violet chelate of a molar ratio 1:2 (silver to QADEAP) in pH 3.5-8.0. This chelate was prconcentrated by solid phase extraction with C18 cartridge. An enrichment factor of 100 was achieved. The molar absorptivity of the chelate is 1.30 x 10(5) L mol(-1) cm(-1) at 590 nm in measured solution. Beer's law is obeyed in the range of 0.01-0.6 microg/ml. The relative standard deviation for eleven replicate samples of 0.01 microg/ml is 1.15%. The detection limit is 0.02 microg/L in the original samples. This method was applied to the determination of microg/L level silver ion in water with good results.     

Simultaneous derivative spectrophotometric determination of zinc and cadmium with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the presence of cetylpyridinium chloride.

A selective and sensitive derivative photometric method has been developed for the determination of trace amounts of Zn2+ with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the presence of cetylpyridinium chloride, a cationic surfactant. The molar-absorption coefficient and analytical sensitivity of the 1:2 complex at 554 nm are 1.19 x 10(5) L mol(-1) cm(-1) and 0.56 ng mL(-1), respectively. The detection limit is 1.96 x 10(-2) ng mL(-1) and Beer's law is valid in the 0.02-0.66 microg mL(-1) range of Zn2+. The developed derivative procedure, using the zero-crossing measurement approach, is applied for the rapid and selective simultaneous determination of Zn2+ and Cd2+ in the range of 0.06-0.66 and 0.20-1.60 microg mL(-1), respectively. Complex matrices, including reference materials, environmental and biological samples and synthetic mixtures, have been successfully analyzed for trace amounts of the two metal ions.     

Evaluation of low-pressure gas chromatography linked to ion-trap tandem mass spectrometry for the fast trace analysis of multiclass pesticide residues

A rapid multiresidue method for the analysis of 72 pesticides has been developed using a single injection with low-pressure gas chromatography/tandem mass spectrometry (LP-GC/MS/MS). The LP-GC/MS/MS method used a short capillary column of 10 m x 0.53 mm i.d. x 0.25 microm film thickness coupled with a 0.6 m x 0.10 mm i.d. restriction at the inlet end. Optimal LP-GC conditions were determined which achieved the fastest separation in MS/MS detection mode. Also MS/MS conditions were optimized in order to increase sensitivity and selectivity. The analytical parameters of the LP-GC/MS/MS method were compared with those obtained by GC/MS/MS using a conventional capillary column (30 m x 0.25 mm i.d. x 0.25 microm film thickness). Better precision and sensitivity values were obtained with the LP-GC/MS/MS approach. The limits of detection (LOD) of the compounds ranged from 0.1 to 14.1 microg L(-1) for LP-GC/MS/MS, lower than those obtained for conventional GC/MS/MS that ranged from 0.1 to 17.5 microg L(-1). The peak widths obtained with the short column in LP-GC are similar to those obtained using conventional capillary GC columns, and the peaks can be successfully identified by MS/MS detection with the conventional scan speed of ion-trap instruments. In addition, the analysis time was significantly reduced with LP-GC/MS/MS (32 min) versus GC/MS/MS (72 min), allowing the number of samples analyzed per day in a routine laboratory to be doubled.     

Cloud point extraction of mercury with PONPE 7.5 prior to its determination in biological samples by ETAAS

Cloud point extraction (CPE) has been used for the pre-concentration of mercury, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by electrothermal atomic absorption spectrometry (ETAAS) using polyethyleneglycolmono-p-nonyphenylether (PONPE 7.5) as surfactant. The chemical variables affecting the separation step were optimized. Under the optimum conditions, i.e, pH 8.5, cloud point temperature 80 degrees C, 5-Br-PADAP=4x10(-5) mol L(-1), PONPE 7.5=0.2%, sample volume=1.0 mL, an enhancement factor of 22-fold was reached. The lower limit of detection (LOD) obtained under the optimal conditions was 0.01 microg L(-1). The precision for 10 replicate determinations at 2.0 microg L(-1) Hg was 4.0% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for mercury was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 16 microg L(-1). The method was successfully applied to the determination of mercury in biological samples and in certified reference material (QC METAL LL3).