Computations for a jet impinging obliquely on a flat surface

A SIMPLE-C algorithm and Jones-Launder k-ε two-equation turbulence model are used to simulate a two-dimensional jet impinging obliquely on a flat surface. Both the continuity and momentum equations for the unsteady state are cast into suitable finite difference equations. The pressure, velocity, turbulent kinetic energy and turbulent energy dissipation rate distributions are solved and show good agreement with various experimental data. The calculations show that the flow field structure of the jet impinging obliquely on a flat surface is strongly affected by the oblique impingement angle. The maximum pressure zone of the obliquely impinging jet flow field moves towards the left as the oblique impingement angle is decreased.     

Stereo-PIV measurements of vapor-induced flow modifications in confined jet impingement boiling

A single subcooled jet of water which undergoes boiling upon impingement on a discrete heat source is studied experimentally using time-resolved stereo particle image velocimetry (PIV). The impinging jet issues from a 3.75 mm diameter sharp-edged orifice in a confining orifice plate positioned 4 orifice diameters from the target surface. The behavior at jet Reynolds numbers of 5,000 and 15,000 is compared for a constant jet inlet subcooling of 10 °C. Fluorescent illumination allows for simultaneous imaging of both the flow tracers and the vapor bubbles in the flow. Flow structure, time-averaged velocities, and turbulence statistics are reported for the liquid regions within the confinement gap for a range of heat inputs at both Reynolds numbers, and the effect of the vapor generation on the flow is discussed. Vapor generation from boiling is found to modify the liquid velocities and turbulence fluctuations in the confinement gap. Flow in the confinement gap is dominated by vapor flow, and the vapor bubbles disrupt both the vertical impinging jet and horizontal wall jet flow. Moreover, vapor bubbles are a significant source of turbulence kinetic energy and dissipation, with the bubbly regions above the heated surface experiencing the most intense turbulence modification. Spectral analysis indicates that a Strouhal number of 0.023 is characteristic of the interaction between bubbles and turbulent liquid jets.     

An experimental investigation on flow structures of confined and unconfined impinging air jets

The flow characteristics of both confined and unconfined air jets, impinging normally onto a flat plate have been experimentally investigated. The mean and turbulence velocities, and surface pressures were measured for Reynolds numbers ranging from 30,000 to 50,000 and the nozzle-to-plate spacings in range of 0.2–6. Smoke-wire technique is used to visualize the flow behavior. The effects of Reynolds number, nozzle-to-plate spacing and flow confinement on the flow structure are reported. In the case of confined jet, subatmospheric regions occur on both impingement and confinement surfaces at nozzle-to-plate spacings up to 2 for all Reynolds numbers in consideration and they lie up to nearly the same radial location at both surfaces. However, there is no evidence of the subatmospheric region in unconfined jet. It is concluded that there exists a linkage among the subatmospheric region, turbulence intensity and the peaks in heat transfer coefficients for low spacings in impinging jets.     

Numerical computation of an impinging jet with uniform wall suction

The paper presents numerical predictions of a turbulent axisymmetric jet impinging onto a porous plate, based on a finite volume method of solving the Navier-Stokes equations for an incompressible air jet with the K–ε turbulence model. The velocity and pressure terms of the momentum equations are solved by the SIMPLE (semi-implicit method for pressure-linked equation) method. In this study, non-uniform staggered grids are used. The parameters of interest include the nozzle-to-wall distance and the suction velocity. The results of the present calculations are compared with available data reported in the literature. It is found that suction effects reduce the boundary layer thickness and increase the velocity gradient near the wall.     

狭缝射流撞击圆柱表面的湍流特性实验研究

实验研究了狭缝射流撞击圆柱表面后壁面射流区的平均流动和湍流特 性. 考察了雷诺数 Re (6000-20000), 喷口到受撞表面距 离 Y/W (5-13), 喷口宽度 W (6.25mm, 9.38mm), 受撞表 面曲率(半圆柱体直径 D = 150mm)对流动和湍流结构的影响. 通过分析 X 热线 在壁面射流区的测量结果发现，在近壁区域，表面曲率、 Re_{w} , Y/W 和 S/W 等 参数对 \sqrt {\overline{u^2}} / U_m 的影响比对 \sqrt {\overline{v^2}} / U_m 强，并且切 应力 \overline {uv} /U_m^2 对表面曲率变化最敏感. 当喷口与受撞击表面之间的距 离 Y/W 在一定范围内增加时， 沿圆柱表面流动的流向和横向的湍流强度增强. 用平板射流和圆柱体表面壁面射流的数据进行比较，从而得到表面曲率对壁面射流特 性的影响. 结果表明，曲率对壁面射流的影响较强， 并随着 S/W 的增大而增强. 随着雷诺数的增大，壁面曲率的影响也有强化的趋势.     

湍流冲击射流流动与传热的数值研究进展

湍流冲击射流由于其冲击表面时具有很高的局部传热率和冲击力,被广泛应用于如表面的加热、电子元件的冷却、纸张的干燥和材料的切割等工程应用和工业过程中.由于其流动的复杂性,也常被作为一种理想的测试实例来评价湍流模型的性能.此外,湍升力射流与地面之间的空气动力作用对V/STOL (垂直或短距离起落)飞机的性能具有很大的影响.长期以来,人们从理论分析、实验测量和数值模拟方面对冲击射流进行了广泛而系统的研究,积累了丰富的资料.本文在分析了湍流冲击射流的数值研究现状的基础上,对近年来有关湍流冲击射流流动与传热的数值研究方面的文献有选择地进行了综述,重点评述了不同湍流模型对冲击射流流动与传热的预测能力,讨论了存在的问题并对该领域今后的研究方向进行了展望.      

On the analysis of an impinging jet on ground effects

Laser Doppler measurements and flow visualization are presented for a turbulent circular jet emerging into a low-velocity cross-stream and, then, impinging on a flat surface perpendicular to the jet-nozzle axis. The experiments were performed for a Reynolds number based on the jet-exit conditions of 6 × 10⁴, a jet-to-crossflow velocity ratio of 30 and for an impingement height of 5 jet diameters and include mean and turbulent velocity characteristics along the two normal directions contained in planes parallel to the nozzle axis. The results, which have relevance to flows found beneath VSTOL aircraft in ground effect, show the presence of a complex 3-D scarf vortex formed around the impinging jet. In zones where measurement data are not available, the flow details are numerically-visualized using a solution of the finite difference form of the fully threedimensional Reynolds-averaged Navier-Stokes equations, incorporating the turbulence viscosity concept. The turbulent structure of the flow is affected by flow distortion at the impinging zone, which results in an unconventional behaviour of the dimensionless structure parameters that determine the empirical constants in engineering models of turbulence. The relative magnitude of the terms involved in the transport equations for the turbulent stresses is quantified from the experimental data in order to assess the importance of these effects and show the extent to which the turbulent structure of the impingement zone is affected by extra rates of strain.     

Automatic eduction and statistical analysis of coherent structures in the wall region of a confined plane turbulent impinging jet

This paper describes a vortex detection algorithm used to expose and statistically characterize the coherent flow patterns observable in the velocity vector fields measured by particle image velocimetry in the impingement region of air curtains. The philosophy and the architecture of this algorithm are presented. Its strengths and weaknesses are discussed. The results of a parametrical analysis performed to assess the variability of the response of our algorithm to the three user-specified parameters in our eduction scheme are reviewed. The technique is illustrated in the case of a plane turbulent impinging twin-jet with an opening ratio of 10. The corresponding jet Reynolds number, based on the initial mean flow velocity U ₀ and the jet width e, is 14,000. The results of a statistical analysis of the size, shape, spatial distribution and energetic content of the coherent eddy structures detected in the impingement region of this test flow are provided. Although many questions remain open, new insights into the way these structures might form, organise and evolve are given. Relevant results provide an original picture of the plane turbulent impinging jet.     

Numerical investigation of the flow and heat behaviours of an impinging jet

The flow and temperature fields of a turbulent impinging jet are rather complex. In order to accurately describe the flow and heat-transfer process, two important factors that must be taken into account are the turbulence model and the wall function. Several turbulence models, including κ–? turbulence models, κ–ω turbulence models, low-Re turbulence models, the κ–κ_l–ω turbulence model, the Transition SST turbulence model, the V2F turbulence model and the RSM turbulence model, are examined and compared to experimental data. Furthermore, for the near wall region, various wall functions are presented for comparison and they include the standard wall function, the scale wall function, the non-equilibrium wall function and the enhanced wall function. The distribution features of velocity, turbulent kinetic energy and Nusselt number are determined in order to provide a reliable reference for the multiphase impinging jet in the future.     

A numerical study of turbulent opposed impinging jets issuing from triangular nozzles with different geometries

In present research, two turbulent opposed impinging air jets issuing from triangular nozzles with fixed and variable exit velocity ratios and different nozzle-to-nozzle distances have been studied numerically and then compared with rectangular and circular nozzles. The finite volume method has been applied for solving mass and momentum equations. The turbulence model being used here is k-ε RNG. Distributions of pressure, turbulence, kinetic energy and its dissipation rate in various regions especially on the impingement regions have been obtained with high accuracy. Study of the nozzle geometries has shown the advantage of triangular nozzles over other geometries. First, the triangle’s base in nozzle geometry has an important role in our study case which, mixing two flows and regions with high turbulence intensity, directly depends on it. Second, our results show that circular and rectangular nozzles have less efficiency than triangular nozzles in mixing applications. Third and last, it was found that the radial jet being created by opposed jets has some similarities to free jets. In this investigation, air in standard atmospheric pressure has been applied as working fluid.     

A turbulent plane offset jet with small offset ratio

 Mean velocities and turbulence characteristics of a turbulent plane offset jet with a small offset ratio of 2.125 have been studied using laser Doppler anemometry (LDA). Static pressure measurements highlight the importance of side plates in enhancing two-dimensionality of the jet. The spatial distributions of turbulence intensities and Reynolds shear stress show a high turbulence recirculating flow region close to the nozzle plate between the jet and the offset plate. The LDA results have been used to examine the capability of three different turbulence models (i.e. k–ɛ, RNG and Reynolds stress) in predicting the velocity field of this jet. While all three models are able to predict qualitatively the recirculation, converging and reattachment regions observed experimentally, the standard k–ɛ turbulence model predicts a reattachment length that best agrees with the experimentally determined value. Received: 11 September 1996/Accepted: 30 May 1997     

Parametric analysis of a round jet impingement on a heated plate

In this study, the flow and heat transfer characteristics of a round air jet have been experimentally investigated in details using two techniques: Particle Image Velocimetry (PIV) and the Laser Doppler Velocimetry (LDV). The measurement of the mean velocity components are compared, and agree well with the experimental data obtained by Baydar (1999). The distributions of the velocity, turbulence quantities and temperature profiles are analyzed in the main characteristic regions of the jet where the heat transfer occurs. Parametric variations were conducted to produce information about the influences of the Reynolds number (Re = 1000, 2000, 3000), the distance between the pipe exit and the flat impingement plate (h/d = 1 and h/d = 2) and the temperature of the plane (T_p = 22 °C, 54 °C, 96 °C) on the impinging jet flow field.     

Turbulence characteristics of radially-confined impinging jet flows

Radially confined, axisymmetric impinging jet flows are investigated by using the standard particle image velocimetry experimental technique. The confinement is achieved by placing a confinement block around a jet, co-axially. The inner diameter of the block is successively varied to nine different values. The inlet-based Reynolds number of the jet is kept constant at 5000. The nine diametric values yielded nine different flows of widely different characteristics. Among other usage, an insight into the flow characteristics can be helpful in designing compact impinging jet applications, as such a radially confined flow is equivalent to passing the pre-impingement jet through a hole perforated in a solid wall (i.e. the jet source can be placed behind a wall). The study has revealed that the flows, in general, form two circulation zones, three mixing layers, and two boundary layers. Based on turbulence characteristics of the five shear layers, overall characteristics of the flows are understood systematically. Mean velocity and various turbulence statistics are also presented, and mechanisms underlying behind their variations are explained. Finally, scaling laws are obtained for the mean velocity and for the turbulence statistics, both in the impingement and in the wall jet regions.     

Time resolved investigations on flow field and quasi wall shear stress of an impingement configuration with pulsating jets by means of high speed PIV and a surface hot wire array

The effects of jet pulsation on flow field and quasi wall shear stress of an impingement configuration were investigated experimentally. The excitation Strouhal number and amplitude were varied as the most influential parameters. A line-array with three submerged air jets, and a confining plate were used. The flow field analysis by means of time resolved particle image velocimetry shows that the controlled excitation can considerably affect the near-field flow of an impinging jet array. These effects are visualized as organization of the coherent flow structures. Augmentation of the Kelvin–Helmholtz vortices in the jet shear layer depends on the Strouhal number and pulsation magnitude and can be associated with pairing of small scale vortices in the jet. A total maximum of vortex strength was observed when exciting with Sr = 0.82 and coincident high amplitudes.Time resolved interaction between impinging vortices and impingement plate boundary layer due to jet excitation was verified by using an array of 5 μm surface hot wires. Corresponding to the global flow field modification due to periodic jet pulsation, the impact of the vortex rings on the wall boundary layer is highly influenced by the above mentioned excitation parameters and reaches a maximum at Sr = 0.82.     

Large Eddy Simulation of a plane impinging jet

Large Eddy Simulations of a plane turbulent impinging jet have been carried out using the dynamic Smagorinsky model. The statistical results are first validated with the measurements from the literature: mean and turbulent quantities along the jet axis and at different vertical locations are presented. This study is completed by the analysis of the wall shear stress at the impingement wall. The effect of the jet Reynolds number (3000Re13500) on the kinematic development of the jet is also discussed. To cite this article: F. Beaubert, S. Viazzo, C. R. Mecanique 330 (2002) 803–810.     

Predictions of axisymmetric and two-dimensional impinging turbulent jets

The k − turbulence model and a version of a second-moment closure, modified to include the effect of pressure reflections from a solid surface, have been used as the basis of predictions of the flow that results from the orthogonal impingement of circular and two-dimensional (2-D) jets on a flat surface. Comparison of model predictions has been made with velocity measurements obtained in the stagnation and wall jet regions of the impinging flows. Results, in general, confirm the superiority of the Reynolds stress transport equation model for predicting mean and fluctuating velocities within the latter regions of such flows. In particular, modifications to the second-moment closure to account for the influence of the surface in distorting the fluctuating pressure field away from the wall successfully predict the damping of normal-to-wall velocity fluctuations throughout the impinging flows. In contrast, results derived from the eddy-viscosity-based approach do not, in general, accurately reproduce experimental observations.     

COMPUTATIONAL STUDIES OF IMPINGING JETS USING K-ϵ TURBULENCE MODELS

This paper reports numerical modelling of impinging jet flows using Rodi and Malin corrections to the k–ϵ turbulence model, carried out using the PHOENICS finite volume code. Axisymmetric calculations were performed on single round free jets and impinging jets and the effects of pressure ratio, height and nozzle exit velocity profile were investigated numerically. It was found that both the Rodi and Malin corrections tend to improve the prediction of the hydrodynamic field of free and impinging jets but still leave significant errors in the predicted wall jet growth. These numerical experiments suggest that conditions before impingement significantly affect radial wall jet development, primarily by changing the wall jet's initial thickness.     

Turbulence measurements in a rectangular mesoscale confined impinging jets reactor

Mesoscale chemical reactors capable of operating in the turbulent flow regime, such as confined impinging jets reactors (CIJR), offer many advantages for rapid chemical processing at the microscale. One application where these reactors are used is flash nanoprecipitation, a method for producing functional nanoparticles. Because these reactors often operate in a flow regime just beyond transition to turbulence, modeling flows in these reactors can be problematic. Moreover, validation of computational fluid dynamics models requires detailed and accurate experimental data, the availability of which has been very limited for turbulent microscale flows. In this work, microscopic particle image velocimetry (microPIV) was performed in a mesoscale CIJR at inlet jet Reynolds numbers of 200, 1,000, and 1,500. Pointwise and spacial turbulence statistics were calculated from the microPIV data. The flow was observed to be laminar and steady in the entire reactor at a Reynolds number of 200. However, at jets Reynolds numbers of 1,000 and 1,500, instabilities as a result of the jets impinging along the centerline of the reactor lead to a highly turbulent impingement region. The peak magnitude of the normalized Reynolds normal and shear stresses within this region were approximately the same for the Reynolds numbers of 1,000 and 1,500. The Reynolds shear stress was found to exhibit a butterfly shape, consistent with a flow field dominated by an oblique rocking of the impingement zone about the center of the reactor. Finally, the spatial auto- and cross-correlations velocity fluctuations were calculated and analyzed to obtain an understanding of size of the coherent structures.     

Heat transfer characteristics of an annular turbulent impinging jet with a confined wall measured by thermosensitive liquid crystal

The present paper describes the heat transfer characteristics of an annular turbulent impinging jet with a confined wall. The local temperature distribution on the impingement surface was measured using a thermosensitive liquid crystal sheet and an image processor. The net heat flux was evaluated by considering the heat conduction in the heated substrate and the thermal radiation between an upper confining insulated wall and an impingement surface. Distributions of the temperature and Nusselt number on the impingement surface were captured in two-dimensional maps. Effects of the diameter ratio of the annular nozzle, the space between nozzle and impingement surface and the Reynolds number on radial distributions of the local Nusselt number were examined. Experimental formulas of the local Nusselt number were obtained in power-law expressions of r/r_p for the major and minor flow regions.     

An experimental investigation of jet screech by air jet impingement on solid boundaries

An experimental investigation has been completed to study several methods of avoiding the jet screech phenomenon due to air jet impingement on solid boundaries. Measurements were completed in the Mach number region of M=0.5 using a 25 mm diameter nozzle with the air jet impinging on flat, concave and convex boundaries. Sound pressure levels were recorded in the plane of the nozzle outlet at a distance of 1.46 m from the jet axis. Hot wire studies and the stagnation pressure at the impingement zone of the jet were also recorded.With the air jet impinging on the flat board normal to its surface a maximum sound pressure occurred at a spacing of approximately two nozzle diameters producing a distinct screech at a sound level of 20 dB above that of the free jet. Three methods of preventing this screech were studied. First, by inserting disturbances into the shear layer at the nozzle exit; second, by changing the geometry of the boundary shape to improve the jet stability in the impingement region; and third, by introducing disturbances at the stagnation region which had the effect of displacing the distinct screech to another frequency range.