Certification for trace elements and methyl mercury mass fractions in IAEA-456 marine sediment sample

Accreditation and Quality Assurance - Marine sediment certified reference material (CRM), IAEA-456 was recently produced by the Environment Laboratories of the International Atomic Energy Agency...     

Critical evaluation of laboratory performance from IAEA-452 (fish scallop) inter-comparison exercise results

The International Atomic Energy Agency Marine Environmental Laboratory (IAEA-MEL) conducted an intercomparison exercise for the “Trace elements and methyl mercury in fish scallop: IAEA-452” in 2009. The Neutron Activation Analysis (NAA) laboratory at PINSTECH, Pakistan took part in this exercise. Comparison with the IAEA results showed that of the 18 elements reported to the IAEA 7 had unacceptable z-scores while the data for two elements was questionable (2< |z-score| <3). Upon investigation it was discovered that the large number of elements having unacceptable z-scores was due to human error and the greater difficulty in analyzing biological samples which have low amounts of trace elements. Therefore selection of values corresponding to matrix matched reference materials (RMs), such as IAEA-436 and IAEA-407, and to non-interfering peaks the results obtained became comparable to the IAEA results with only the result for As having |z-score|> 3.     

Certification of the mass fractions of trace elements and pentachlorophenol in an impregnated wood reference material

The resource-saving utilisation of recovered waste wood is a matter of growing concern. In several European countries, this utilisation is governed by regulations and is dependent on the contents of certain trace elements and organic compounds. Thus, for decision-making with respect to waste wood management (recycling or combustion), reliable analytical data are needed and, due to their great economic and environmental impact, must be assured by appropriate quality control. To support the improvement in quality assurance in waste wood analysis, for the first time, a wood reference material was certified for its mass fractions of arsenic, cadmium, chromium, copper, lead, mercury, and pentachlorophenol (PCP). These analytes were selected because they represent typical constituents of wood preservatives most widely used in the past. Material preparation and testing of homogeneity and stability were carried out by BAM Federal Institute for Materials Research and Testing. The certification measurements were performed involving selected laboratories with documented expertise in the field of waste wood analysis. The certified values and their corresponding uncertainties were assigned in full compliance with the requirements of ISO Guide 35. The certified mass fractions and their expanded uncertainties (k = 2) are as follows: (3.1 ± 0.5) mg/kg for As, (3.02 ± 0.24) mg/kg for Cd, (36.4 ± 2.6) mg/kg for Cr, (22.9 ± 1.7) mg/kg for Cu, (0.60 ± 0.14) mg/kg for Hg, (39 ± 4) mg/kg for Pb, and (7.9 ± 0.6) mg/kg for PCP. The certified material is available as European Reference Material ERM^®-CD100.     

Certification of trace and major elements and methylmercury concentrations in a macroalgae (Fucus sp.) reference material, IAEA-140

A marine reference material, IAEA-140, prepared with a macroalgae (Fucus sp.) was recently produced by the International Atomic Energy Agency and certified for trace and major elements and for methylmercury (MeHg). Certification of this material was achieved as an outcome of an international analytical intercomparison study which resulted in 116 independent sets of results reported by participants from 54 countries. The statistical evaluation of the collected data and the criteria used for assignment of the mean and uncertainty values are described. The analysis of data allowed to certify concentration values for 24 elements and MeHg, and to provide information values for another 10 elements. Regarding the elements which could be given certified values, between two and eight different instrumental methods were used to measure metal concentrations, and four independent analytical procedures were used to measure MeHg concentrations. In order to assess the results of the certification procedure, a comparison was made between the certified values obtained from the world-wide intercomparison results and the values obtained from a small subgroup of well-qualified laboratories. The means and 95% confidence intervals for reference values obtained by the two methods are similar for most elements showing that the usual method of certification used by the IAEA, based on large groups of participants, is indeed pertinent.     

Certification of trace and major elements and methylmercury concentrations in a macroalgae (Fucus sp.) reference material, IAEA-140

A marine reference material, IAEA-140, prepared with a macroalgae (Fucus sp.) was recently produced by the International Atomic Energy Agency and certified for trace and major elements and for methylmercury (MeHg). Certification of this material was achieved as an outcome of an international analytical intercomparison study which resulted in 116 independent sets of results reported by participants from 54 countries. The statistical evaluation of the collected data and the criteria used for assignment of the mean and uncertainty values are described. The analysis of data allowed to certify concentration values for 24 elements and MeHg, and to provide information values for another 10 elements. Regarding the elements which could be given certified values, between two and eight different instrumental methods were used to measure metal concentrations, and four independent analytical procedures were used to measure MeHg concentrations. In order to assess the results of the certification procedure, a comparison was made between the certified values obtained from the world-wide intercomparison results and the values obtained from a small subgroup of well-qualified laboratories. The means and 95% confidence intervals for reference values obtained by the two methods are similar for most elements showing that the usual method of certification used by the IAEA, based on large groups of participants, is indeed pertinent.     

Certification of total mercury and methylmercury concentrations in mussel homogenate (Mytilus edulis) reference material, IAEA-142

Due to the increased demand for new reference materials certified for total and methylmercury (MeHg) a sample of mussel homogenate (IAEA-142) has been prepared. Thirteen experienced laboratories reported results for total Hg of which 9 laboratories also reported results for MeHg content. Laboratories reporting MeHg results used various isolation techniques (solvent extraction, saponification, acid leaching, ion-exchange separation, and distillation) and detection systems (cold vapour atomic absorption spectrometry (CV AAS), cold vapour atomic fluorescence spectrometry (CV AFS), gas chromatography with electron capture detector (GC/ECD) and HPLC with CV AAS detector). In the case of total Hg, most of the laboratories used acid digestion, only two used alkaline dissolution, followed either by CV AAS or CV AFS. One laboratory used neutron activation analyses with radiochemical separation. The data received were in good agreement. The value for total Hg was certified to be 126 ng/g, with a 95% confidence interval from 119 to 132 ng/g. For MeHg the certified value of 47 ng/g expressed as Hg was assigned, with a 95% confidence interval from 43 to 51 ng/g. Stability testing has shown that both total and MeHg are stable if samples are stored in a dry and dark place at room temperature. The sample is now available as a certified reference material and is, in particular, useful for quality control measurements of Hg and MeHg in mussel samples at low concentration levels. Received: 24 September 1996 / Revised: 20 November 1996 / Accepted: 8 December 1996     

Certification of total mercury and methylmercury concentrations in mussel homogenate (Mytilus edulis) reference material, IAEA-142

Due to the increased demand for new reference materials certified for total and methylmercury (MeHg) a sample of mussel homogenate (IAEA-142) has been prepared. Thirteen experienced laboratories reported results for total Hg of which 9 laboratories also reported results for MeHg content. Laboratories reporting MeHg results used various isolation techniques (solvent extraction, saponification, acid leaching, ion-exchange separation, and distillation) and detection systems (cold vapour atomic absorption spectrometry (CV AAS), cold vapour atomic fluorescence spectrometry (CV AFS), gas chromatography with electron capture detector (GC/ECD) and HPLC with CV AAS detector). In the case of total Hg, most of the laboratories used acid digestion, only two used alkaline dissolution, followed either by CV AAS or CV AFS. One laboratory used neutron activation analyses with radiochemical separation. The data received were in good agreement. The value for total Hg was certified to be 126 ng/g, with a 95% confidence interval from 119 to 132 ng/g. For MeHg the certified value of 47 ng/g expressed as Hg was assigned, with a 95% confidence interval from 43 to 51 ng/g. Stability testing has shown that both total and MeHg are stable if samples are stored in a dry and dark place at room temperature. The sample is now available as a certified reference material and is, in particular, useful for quality control measurements of Hg and MeHg in mussel samples at low concentration levels.     

Determination of trace elements by resonant ionization mass spectrometry (RIMS)

Summary A resonant ionization mass spectrometer has been developed as an analytical tool for the detection of trace elements, especially of plutonium and other radionuclides. The sample, deposited on a rhenium filament, is evaporated by electrical heating and the atoms of the element under investigation are selectively ionized by laser light delivered from three dye lasers pumped by a copper vapour laser. The resulting photoions are detected in a time-of-flight spectrometer with a channelplate detector. For plutonium a mass resolution of M/M=1500 was obtained and an overall detection efficiency of 4×10^–6 was determined for stepwise excitation and ionization via autoionizing states. With a laser light bandwidth of 3–5 GHz neighbouring isotopes could be suppressed by a factor of 20 due to isotope shifts in the excitation transitions. The isotope composition of synthetic samples was measured and good agreement was found with mass spectroscopic results. The influence of the hyperfine structure on the isotope ratios is discussed.

---

Bestimmung von Spurenelementen durch resonante Ionisations-Massenspektrometrie (RIMS)

     

Quantification of trace elements in human serum fractions by liquid chromatography and inductively coupled plasma mass spectrometry

On‐line coupling of LC and ICP‐MS has been used for fractionation and detection of species of Cu, Fe, I, Se and Zn in human serum. It has been shown that anion exchange chromatography provided better separation capability (both intra‐ and inter‐element) than size‐exclusion chromatography. The mobile phases for ion exchange chromatography consisted of Tris–HNO₃ buffer and ammonium salt (nitrate, acetate or formate). Formate was found to be the best mobile phase counter ion, enabling good chromatographic separation, and is acceptable for mass spectrometry too. The quantitative evaluation of element concentrations adhering to individual fractions was performed by the peak area normalization method. The repeatability of results ranged from 3 to 15% (depending on the element concentration level) and represented the main part of the result uncertainty. The accuracy of Cu and Zn fraction determinations was confirmed by comparison with the isotope dilution technique. Copyright © 2006 John Wiley & Sons, Ltd.     

A new reference material for radionuclides in the mussel sample from the Mediterranean Sea (IAEA-437)

A new Reference Material (RM) for radionuclides in mussel (Mytilus galloprovincialis) from the Mediterranean Sea (IAEA-437) is described and the results of the certification process are presented. Four radionuclides (⁴⁰K, ²³⁴U, ²³⁸U, and ^239+240Pu) have been certified, and information values on massic activities with 95% confidence intervals are given for nine radionuclides (¹³⁷Cs, ²¹⁰Pb(²¹⁰Po), ²²⁶Ra, ²²⁸Ra, ²²⁸Th, ²³⁰Th, ²³²Th, ²³⁵U, and ²⁴¹Am). Results for less frequently reported radionuclides (⁹⁰Sr, ¹²⁹I, ²³⁸Pu, ²³⁹Pu, and ²⁴⁰Pu) are also reported. The RM can be used for quality assurance/quality control of the analysis of radionuclides in mussel samples, for the development and validation of analytical methods and for training purposes. The material is available in 200 g units.     

A certified reference material for radionuclides in the water sample from Irish Sea (IAEA-443)

A new certified reference material (CRM) for radionuclides in sea water from the Irish sea (IAEA-443) is described and the results of the certification process are presented. Ten radionuclides (³H, ⁴⁰K, ⁹⁰Sr, ¹³⁷Cs, ²³⁴U, ²³⁵U, ²³⁸U, ²³⁸Pu, ^239+240Pu and ²⁴¹Am) have been certified, and information values on massic activities with 95% confidence intervals are given for four radionuclides (²³⁰Th, ²³²Th, ²³⁹Pu and ²⁴⁰Pu). Results for less frequently reported radionuclides (⁹⁹Tc, ²²⁸Th, ²³⁷Np and ²⁴¹Pu) are also reported. The CRM can be used for quality assurance/quality control of the analysis of radionuclides in water samples, for the development and validation of analytical methods and for training purposes. The material is available in 5 L units from IAEA (http://nucleus.iaea.org/rpst/index.htm).     

Present-day methods for the determination of trace elements in oil and its fractions

The development and use of instrumental methods for the determination of a wide range of trace elements in oil is considered. Special attention is paid to methods of the direct introduction of samples into spectrometers. It is shown that preliminary sample preparation is in certain cases necessary for the determination of trace elements in oil. The main methods of sample preparation of oils, including methods of extraction of a series of trace elements from crude oil (extraction, membrane, sorption, etc.), are described.     

Certification of 22 elements in a pure copper (99.5%) sample for spark emission and X-ray fluorescence spectrometry (CRM BAM-376)

 The element contents of Ag, Al, As, Be, Bi, Cd, Co, Cr, Fe, Mg, Mn, Ni, P, Pb, S, Sb, Se, Sn, Te, Ti, Zn and Zr in a pure copper (99.5%) sample (CRM BAM-376) for use in spark emission and X-ray fluorescence spectrometry were certified and the certified values are given. For Si, the certification has not yet been completed, the content of this element will be certified later. The sample was produced and certified in collaboration with the Committee of Chemists of the GDMB Gesellschaft für Bergbau, Metallurgie, Rohstoff- und Umwelttechnik. Data of the homogeneity testing and the certification campaign with 14 participating laboratories using different analytical methods are reported. Received: 3 February 1997/Revised: 21 February 1997/Accepted: 5 March 1997     

Determination of trace elements in marine plankton by inductively coupled plasma mass spectrometry (ICP-MS)

A method has been developed for the determination of 23 elements in marine plankton in which inductively coupled plasma (ICP) source mass spectrometry (MS) was used to quantify the elements in the solution after digestion in a mixture of hydrofluoric and nitric acids in sealed PTFE vessels in a microwave field. The procedure was validated by the analysis of a standard reference soil (SRM 2709 San Joaquin Soil) and a standard reference fresh water plankton (CRM 414). The method was applied to the analysis of several marine plankton samples grown under controlled conditions including several whose growth media had been enriched with selenium. Matrix induced signal suppressions and instrumental drift were corrected by internal standardization. The suitabilities of germanium, indium, rhodium, scandium and yttrium as internal standard elements were evaluated. Neither scandium nor yttrium could be used due to the presence of these elements in the samples, germanium was used for the determination of As, Co, Cu, Fe, Ni, Se, Si and Zn, indium was used for Al, Ba, Ca, Eu, Sr, and Tl, and rhodium was used for Cd, Cr, Hg, Mg, Pb, Sb, Sn, and V. For Al, Ca, Cr, Cu, Fe, Mg, Mn, Ni, Si, Sr, V, and Zn internal standardization did not completely compensate for the suppressive effect of the heavier elements and the solutions were diluted. However, for As, Ba, Cd, Co, Eu, Hg, Pb, Sb, Se, Sn and Tl, it was possible to obtain accurate results despite the 35–¶40% suppression in the signals. Isobaric overlap was only a problem in the cases of ⁴²Ca and ⁷⁸Se; ⁴⁴Ca and ⁷⁷Se, respectively, were used. Memory effects were only observed with Hg for which a nitric acid-sodium chloride solution was the most effective wash-out solution. The marine plankton samples were able to tolerate a higher concentration of Hg as the selenium concentration increased.     

Determination of trace elements in marine plankton by inductively coupled plasma mass spectrometry (ICP-MS)

A method has been developed for the determination of 23 elements in marine plankton in which inductively coupled plasma (ICP) source mass spectrometry (MS) was used to quantify the elements in the solution after digestion in a mixture of hydrofluoric and nitric acids in sealed PTFE vessels in a microwave field. The procedure was validated by the analysis of a standard reference soil (SRM 2709 San Joaquin Soil) and a standard reference fresh water plankton (CRM 414). The method was applied to the analysis of several marine plankton samples grown under controlled conditions including several whose growth media had been enriched with selenium. Matrix induced signal suppressions and instrumental drift were corrected by internal standardization. The suitabilities of germanium, indium, rhodium, scandium and yttrium as internal standard elements were evaluated. Neither scandium nor yttrium could be used due to the presence of these elements in the samples, germanium was used for the determination of As, Co, Cu, Fe, Ni, Se, Si and Zn, indium was used for Al, Ba, Ca, Eu, Sr, and Tl, and rhodium was used for Cd, Cr, Hg, Mg, Pb, Sb, Sn, and V. For Al, Ca, Cr, Cu, Fe, Mg, Mn, Ni, Si, Sr, V, and Zn internal standardization did not completely compensate for the suppressive effect of the heavier elements and the solutions were diluted. However, for As, Ba, Cd, Co, Eu, Hg, Pb, Sb, Se, Sn and T1, it was possible to obtain accurate results despite the 35-40% suppression in the signals. Isobaric overlap was only a problem in the cases of 42Ca and 78Se; 44Ca and 77Se, respectively, were used. Memory effects were only observed with Hg for which a nitric acid-sodium chloride solution was the most effective wash-out solution. The marine plankton samples were able to tolerate a higher concentration of Hg as the selenium concentration increased.     

Determination of trace elements in biological materials using tetramethylammonium hydroxide for sample preparation

A method to prepare milk powder, bovine liver and bovine muscle samples for analysis by electrothermal atomic absorption spectrometry (ETAAS) is proposed. Samples are mixed with a small amount of tetramethylammonium hydroxide (TMAH) and a stable and homogeneous slurry is produced in ca. 2 h with heating at 60–70 °C. After such sample preparation and dilution with water, trace elements are determined in certified reference materials. Pyrolysis and atomisation temperatures are optimised for each element, and several modifiers are investigated. External calibration is used for every analyte. Limits of detection (LODs), precision and accuracy are reported for Cd, Pb, Ni, Cr, Cu and Ag and compared with those obtained after conventional acid digestion. The main advantages of the proposed method are the simplicity of sample preparation and the longer lifetime of the graphite tube.     

Measurement of methyl mercury (I) and mercury (II) in fish tissues and sediments by HPLC-ICPMS and HPLC-HGAAS

A procedure for the extraction and determination of methyl mercury and mercury (II) in fish muscle tissues and sediment samples is presented. The procedure involves extraction with 5% (v/v) 2-mercaptoethanol, separation and determination of mercury species by HPLC-ICPMS using a Perkin-Elmer 3 μm C8 (33 mm × 3 mm) column and a mobile phase 3 containing 0.5% (v/v) 2-mercaptoethanol and 5% (v/v) CH₃OH (pH 5.5) at a flow rate 1.5 ml min⁻¹ and a temperature of 25 °C. Calibration curves for methyl mercury (I) and mercury (II) standards were linear in the range of 0-100 μg l⁻¹ (r² = 0.9990 and r² = 0.9995 respectively). The lowest measurable mercury was 0.4 μg l⁻¹ which corresponds to 0.01 μg g⁻¹ in fish tissues and sediments. Methyl mercury concentrations measured in biological certified reference materials, NRCC DORM - 2 Dogfish muscle (4.4 ± 0.8 μg g⁻¹), NRCC Dolt - 3 Dogfish liver (1.55 ± 0.09 μg g⁻¹), NIST RM 50 Albacore Tuna (0.89 ± 0.08 μg g⁻¹) and IRMM IMEP-20 Tuna fish (3.6 ± 0.6 μg g⁻¹) were in agreement with the certified value (4.47 ± 0.32 μg g⁻¹, 1.59 ± 0.12 μg g⁻¹, 0.87 ± 0.03 μg g⁻¹, 4.24 ± 0.27 μg g⁻¹ respectively). For the sediment reference material ERM CC 580, a methyl mercury concentration of 0.070 ± 0.002 μg g⁻¹ was measured which corresponds to an extraction efficiency of 92 ± 3% of certified values (0.076 ± 0.04 μg g⁻¹) but within the range of published values (0.040-0.084 μg g⁻¹; mean ± s.d.: 0.073 ± 0.05 μg g⁻¹, n = 40) for this material. The extraction procedure for the fish tissues was also compared against an enzymatic extraction using Protease type XIV that has been previously published and similar results were obtained. The use of HPLC-HGAAS with a Phenomenox 5 μm Luna C18 (250 mm × 4.6 mm) column and a mobile phase containing 0.06 mol l⁻¹ ammonium acetate (Merck Pty Limited, Australia) in 5% (v/v) methanol and 0.1% (w/v) l-cysteine at 25 °C was evaluated as a complementary alternative to HPLC-ICPMS for the measurement of mercury species in fish tissues. The lowest measurable mercury concentration was 2 μg l⁻¹ and this corresponds to 0.1 μg g⁻¹ in fish tissues. Analysis of enzymatic extracts analysed by HPLC-HGAAS and HPLC-ICPMS gave equivalent results.     

Certification of the methylmercury content in SRM 2977 mussel tissue (organic contaminants and trace elements) and SRM 1566b oyster tissue

The methylmercury content in two new marine bivalve mollusk tissue Standard Reference Materials (SRMs) has been certified using results of analyses from the National Institute of Standards and Technology (NIST) and two other laboratories. The certified concentrations of methylmercury were established based on the results from four and six different (independent) analytical methods, respectively, for SRM 1566b Oyster Tissue (13.2 +/- 0.7 microg/kg) and SRM 2977 Mussel Tissue (organic contaminants and trace elements) (36.2 +/- 1.7 microg/kg). The certified concentration of methylmercury in SRM 1566b is among the lowest in any certified reference material (CRM).     

Certification of the methylmercury content in SRM 2977 Mussel Tissue (organic contaminants and trace elements) and SRM 1566b Oyster Tissue

The methylmercury content in two new marine bivalve mollusk tissue Standard Reference Materials (SRMs) has been certified using results of analyses from the National Institute of Standards and Technology (NIST) and two other laboratories. The certified concentrations of methylmercury were established based on the results from four and six different (independent) analytical methods, respectively, for SRM 1566b Oyster Tissue (13.2 ± 0.7 μg/kg) and SRM 2977 Mussel Tissue (organic contaminants and trace elements) (36.2 ± 1.7 μg/kg). The certified concentration of methylmercury in SRM 1566b is among the lowest in any certified reference material (CRM).