On the nature of acid centers in Mg-containing ZSM-5 zeolites

The catalytic activity of ZSM-5 zeolites containing Mg cations in various concentrations has been studied in the alkylation of toluene by ethylene. The concentration of acid centers of different nature in these zeolites was characterized by IR spectroscopy of OH-groups and adsorbed CO. The state of Mg cations in the samples was studied by¹⁵N NMR of the adsorbed N₂O. The increase of Mg content was shown to decrease both the concentration of non-protic acid sites of medium strength and the activity of samples, which is related to the increase of association degree of Mg cations in the zeolite.     

Catalytic activity of H-forms of zeolites in the isomerization of supercritical <Emphasis Type="Italic">n</Emphasis>-pentane and their physicochemical properties

The acidic properties of the H-forms of zeolites ZSM-5, Beta, Y, and mordenite are studied by diffuse reflectance IR spectroscopy using n-pentane as a probe molecule. The decreasing order of Brønsted acid site strengths is constructed. The isopentane selectivity in n-pentane isomerization under supercritical conditions (260°C, 130 atm) increases in the order H-ZSM-5 < H-Beta < H-mordenite(11) ≈ H-Y with decreasing strength of Brønsted sites. Catalytic data are analyzed jointly with the results of physicochemical studies of H-mordenite (temperature-programmed ammonia desorption, benzene adsorption, and IR spectroscopy). Under the supercritical conditions, the conversion of n-pentane on mordenite is determined by the total acidity of the zeolite and also by the accessibility of the acid sites inside the zeolite channels to the reactant.     

Influence of H3PMo12O40/SiO2 thermal treatment on adsorbed forms of formaldehyde and formic acid

Effect of the H₃PMo₁₂O₄₀/SiO₂(P-Mo-HPA) thermal treatment on adsorbed forms of HCOOH and H₂CO has been studied by IR spectroscopy. On the sample pretreated at 150°C, HCOOH adsorbed mainly as hydrogen-bonded complexes. The HPA calcination at 350°C resulted in the formation of surface formates along with hydrogen-bonded complexes. This proves the formation of coordinatively unsaturated surface cations (Lewis acid sites) during HPA dehydration. Alteration of the surface composition due to dehydration was found to have a major influence on the H₂CO adsorbed forms.     

OFF沸石中锂离子在骨架外的分布及可接近性

对OFF沸石进行离子交换制备出NH4-OFF沸石,然后通过Li2CO3/NH4-OFF体系的固态反应制备了不同锂离子交换度的Li-OFF沸石。对吸附氮气和氧气的Li-OFF样品进行了7Li MAS NMR表征。研究发现,所有吸附氧气样品的部分7Li MAS NMR共振峰均发生了顺磁位移。通过对实验谱的拟合,得知Li-OFF沸石中的锂离子可分布在三类阳离子位置（A、B和C）上,对应于三个不同位移的谱峰。Li+离子并非等比例地进入三个可交换的位置,而是优先占据主孔道中的A位置,随着交换度的升高,位能较高的C和B位置上的Li离子占有率逐渐增加。在100％固态交换度样品中,Li+离子在不同离子位的占有率分别为17％(位置B)、29％(位置C)和54％(位置A)。其中,位置B是O2分子不可接近的,所以Li-OFF沸石中有83％的阳离子是可以接近的。     

Dibenzodioxin adsorption on inorganic materials

Dibenzodioxin adsorption/desorption on solid surfaces is an important issue associated with the formation, adsorption, and emission of dioxins. Dibenzodioxin adsorption/desorption behaviors on inorganic materials (amorphous/mesoporous silica, metal oxides, and zeolites) were investigated using in situ FT-IR spectroscopy and thermogravimetric (TG) analysis. Desorption temperatures of adsorbed dibenzodioxin are very different for different kinds of inorganic materials: approximately 200 degrees C for amorphous/mesoporous silica, approximately 230 degrees C for metal oxides, and approximately 450 degrees C for NaY and mordenite zeolites. The adsorption of dibenzodioxin can be grouped into three categories according to the red shifts of the IR band at 1496 cm(-1) of the aromatic ring for the adsorbed dibenzodioxin: a shift of 6 cm(-1) for amorphous/mesoporous silica, a shift of 10 cm(-1) for metal oxides, and a shift of 14 cm(-1) for NaY and mordenite, suggesting that the IR shifts are proposed to associated with the strength of the interaction between adsorbed dibenzodioxin and the inorganic materials. It is proposed that the dibenzodioxin adsorption is mainly via the following three interactions: hydrogen bonding with the surface hydroxyl groups on amorphous/mesoporous silica, complexation with Lewis acid sites on metal oxides, and confinement effect of pores of mordenite and NaY with pore size close to the molecular size of dibenzodioxin.     

Intensities of C-H IR stretching bands of ethane and propane adsorbed by zeolites as a new spectral criterion of their chemical activation via polarization resulting from stretching of chemical bonds

Polarization of ethane and propane resulting from adsorption of these hydrocarbons by protons and different cations in mordenite, ZSM-5, and Y zeolites was studied by diffuse reflection Fourier transform IR spectroscopy (DRIFTS). Perturbation of adsorbed molecules by protons and sodium cations is weak, while positions of absorption bands for both these zeolites are very close to each other. In contrast, distributions of C-H IR stretching bands in intensities are somewhat different. This effect is pronounced much stronger for adsorption of light paraffins by bivalent alkaline earth and zinc cationic forms of these zeolites. Distribution of relative intensities of absorption bands strongly depends in this case both on the nature of cations and on the zeolites, while the most strongly perturbed vibrations are the initially fully symmetric C-H stretching vibrations. The corresponding low-frequency shifts and relative intensities of IR bands are increasing for different cations and zeolites in the following sequences: Na < Ca < Mg < Zn and Y < Mor approximately ZSM-5, while the difference in distribution of relative intensities of C-H stretching bands is pronounced much stronger than for the low-frequency shifts of these bands. Therefore, the relative intensities of IR C-H stretching bands are much better criterion of perturbation of light paraffins upon adsorption than the frequencies of these bands, which are traditionally used for this purpose. In addition, distribution of C-H IR stretching bands in intensity also provides unique information on anisotropy of polarizability of different C-H bonds created by their vibrations. For the acid and acid-base catalysis, where the main source of chemical activation arises from polarization of adsorbed molecules, such information is most important, while the anisotropy of polarizability provides a unique information on selective activation of different chemical bonds resulting from their stretching. The obtained results also demonstrate the possibility to use for testifying of the strength of Lewis acid sites instead of adsorption of the model molecular probes adsorption of the paraffins themselves.     

A density functional theory study of molecular and dissociative adsorption of H2 on active sites in mordenite

Adsorption and chemisorption of H2 in mordenite is studied using ab initio density functional theory (DFT) calculations. The geometries of the adsorption complex, the adsorption energies, stretching frequencies, and the capacity to dissociate the adsorbed molecule are compared for different active sites. The active centers include a Br?nsted acid site, a three-coordinated surface Al site, and Lewis sites formed by extraframework cations: Na+, Cu+, Ag+, Zn2+, Cu2+, Ga3+, and Al3+. Adsorption properties of cations are compared for a location of the cation in the five-membered ring. This location differs from the location in the six-membered ring observed for hydrated cations. The five-membered ring, however, represents a stable location of the bare cation. In this position any cation exhibits higher reactivity compared with the location in the six-membered ring and is well accessible by molecules adsorbed in the main channel of the zeolite. Calculated adsorption energies range from 4 to 87 kJ/mol, depending on electronegativity and ionic radius of the cation and the stability of the cation-zeolite complex. The largest adsorption energy is observed for Cu+ and the lowest for Al3+ integrated into the interstitial site of the zeolite framework. A linear dependence is observed between the stretching frequency and the bond length of the adsorbed H2 molecule. The capacity of the metal-exchanged zeolite to dissociate the H2 molecule does not correlate with the adsorption energy. Dissociation is not possible on single Cu+ cation. The best performance is observed for the Ga3+, Zn2+, and Al3+ extraframework cations, in good agreement with experimental data.     

Identification of two types of exchangeable sites for monovalent copper ions exchanged in MFI-type zeolite

Three different approaches have been used to characterize the state of exchanged copper ions in copper-ion-exchanged MFI (CuMFI) samples. (1) Two types of an ion-exchangeable site with different adsorption properties for N(2) or CO molecules were identified depending on the pre-treatment temperature (723 or 873 K) of a sample prepared by using an aqueous solution of CuCl(2). (2) The state of the active sites formed by the evacuation of a sample at 873 K that had been prepared using a mixture solution of aqueous NH(4)CH(3)COO and Cu(CH(3)COO)(2) was analysed utilizing both (13)C(18)O and (12)C(16)O to identify the two types of active adsorption sites for CO molecules. (3) CuMFI samples prepared by the ion-exchange method employing anhydrous CuCH(3)COO showed a surprising adsorption feature characterized by a single IR band occurring at 2159 cm(-1) due to the adsorbed CO molecules, but there was no corresponding IR band due to adsorbed N(2) molecules. A successful preparation of CuMFI, in which the monovalent copper ions exclusively occupied another one of the two types of ion-exchangeable sites, was also carried out utilizing the solid-ion exchange method using Cu(CH(3)COO)(2).H(2)O. This site exhibits an IR band occurring at 2151 cm(-1) for CO molecules and also acts as an active site for N(2) molecules. These experimental data correlate, and clearly indicate that there are at least two types of exchangeable sites for copper ions in MFI-type zeolites.     

Carbon monoxide adsorption on low-silica zeolites: from single to dual and to multiple cation sites

Infrared spectra of CO adsorbed on the Al-rich Na-A zeolite were analysed by using a combined theoretical and experimental approach, showing that such spectra cannot be interpreted by assigning each IR band to CO interacting with a specific type of single cation site. This concept, which usually works well for high-silica zeolites, should not be uncritically extended to Al-rich zeolites that are crowded with cations in configurations which lead to preferential formation of CO adsorption complexes involving more than one cation site.     

Acidic Properties of Sulfated Zirconia

IR spectroscopy of adsorbed probe molecules (CO, pyridine) is used to characterize the acidic properties of sulfated zirconia derived from zirconium oxide and hydroxide. Their acidic properties are found to be similar. The strength of the Lewis and Brönsted site measured by the frequency shift of adsorbed CO is lower than that in zeolites. It is concluded that sulfated zirconia have no superacid Brönsted and Lewis sites. Brönsted sites capable of protonating pyridine vanish when calcining the catalysts at temperature above 773 K, but the strength and concentration of the Lewis acid sites (LAS) do not change.     

On the location of Lewis acidic aluminum in zeolite mordenite and the role of framework-associated aluminum in mediating the switch between Brønsted and Lewis acidity

Lewis acidic aluminum in zeolites, particularly acidity that is inherent to the framework, is an indeterminate concept. A fraction of framework aluminum changes geometry to octahedral coordination in the proton form of zeolite mordenite. Such octahedrally coordinated aluminum is the precursor of a Lewis acid site and its formation is accompanied by a loss in Brønsted acidity. Herein, we show that such Lewis acid sites have a preferred location in the pore structure of mordenite. A greater proportion of these Lewis acid sites resides in the side-pockets than in the main channel. By reverting the octahedrally coordinated aluminum back to a tetrahedral geometry, the corresponding Brønsted acid sites are restored with a concomitant loss in the ability to form Lewis acid sites. Thereby, reversible octahedral–tetrahedral aluminum coordination provides a means to indirectly switch between Lewis and Brønsted acidity. This phenomenon is unique to Lewis acidity that is inherent to the framework, thereby distinguishing it from Lewis acidity originating from extra-framework species. Furthermore, the transformation of framework aluminum into octahedral coordination is decoupled from the generation of distorted tetrahedrally coordinated aluminum, where the latter gives rise to the IR band at 3660 cm⁻¹ in the OH stretching region.

Framework-associated aluminum is demonstrated to facilitate a reversible switch between Lewis and Brønsted acidity in zeolites with the Lewis acid sites preferentially populating the side-pockets in the case of mordenite.     

H2对Rh-Mn-Li-Ti/SiO2催化剂上CO吸附和脱附的影响

 应用红外光谱和程序升温脱附技术研究了Rh-Mn-Li-Ti/SiO2催化剂上H2对CO吸附和脱附的影响. 结果表明,预吸附的H2主要占据线式CO的吸附位. 共吸附时H2与CO在Rh位上形成了羰基氢化物,从而导致线式物种谱带红移,且高的H2浓度有利于CO的吸附. 在323 K下, H2对预吸附的CO谱带位置和强度没有影响. 但是,随着温度的升高, H2的存在促进了弱吸附CO的脱附,并使之重新吸附; 同时, H2促进了强吸附CO的解离,增强了CO的吸附强度和催化剂的吸附能力.     

H（Mg,Co）AlPO4—5杂原子分子筛的酸性质测定

以红外光谱和程序升温脱附法研究了H(Mg,Co)AlPO_4-5分子筛的酸性,样品红外谱图中的3820和3680cm~(-1)谱峰分别归属于v_(Al—OH)和v_(p—OH),而3660～3568cm~(-1)谱峰则分别归属于HMgAlPO_4-5和HCoAlPO_4-5分子筛的M(OH)P(M=Mg,Co)基团的振动,酸强度顺序为:Co(OH)P>Mg(OH)P>P(OH)>Al(OH),吡啶吸附的红外光谱揭示,H(Mg,Co)AlPO_4-5分子筛具有较高酸强度的B酸和L酸中心。NH_3-TPD表明分子筛的酸强度顺序为H(Co)AlPO_4-5>H(Mg)AlPO_4-5>>AlPO_4-5。     

FTIR spectroscopic study of titanium-containing mesoporous silicate materials

The surface acidity of different mesoporous titanium-silicates, such as well-organized hexagonally packed Ti-MMM, Ti-MMM-2, Ti-SBA-15, and amorphous TiO(2)-SiO(2) mixed oxides (aerogels and xerogels), was studied by means of FTIR spectroscopy of CO adsorbed at 80 K and CD(3)CN adsorbed at 293 K. The surface hydroxyl groups of mesoporous titanium-silicates with 2-7 wt % Ti revealed a Br?nsted acidity slightly higher to that of pure silicate. TiO(2)-SiO(2) xerogels revealed the highest Br?nsted acidity among the titanium-silicates studied. CO adsorption revealed two additional sites on the surface in comparison to pure silicate, characterized by nu(CO) from 2185 (high pressure) to 2178 (low pressure) cm(-1) and from 2174 (high pressure) to 2170 (low pressure) cm(-1). These bands are due to CO adsorbed on isolated titanium cations in the silica surrounding or having one Ti(4+) cation in their second coordination sphere and due to CO interactions with Ti-OH groups, respectively. CD(3)CN adsorption similarly revealed the existence of two additional sites, which were not detected for pure silicate: at 2289 cm(-1) due to CD(3)CN interaction with titanol groups and from 2306 (low pressure) to 2300 (high pressure) cm(-1) due to acetonitrile interaction with isolated framework titanium cations with probably one Ti(4+) cation in their second coordination shell. The spectroscopic results are compared with computational data obtained on cluster models of titanium-silicate with different titanium content. According to the IR data, the Ti accessibility on the surfaces for mesoporous titanium-silicates with similar Ti loading (2 wt %) was found to fall in the order TiO(2)-SiO(2) aerogel approximately TiO(2)-SiO(2) xerogel > Ti-MMM approximately Ti-MMM-2 > Ti-SBA-15. This order (except TiO(2)-SiO(2) xerogel) correlates with the catalytic activity found previously for titanium-silicates in 2,3,6-trimethylphenol oxidation with H(2)O(2).     

Relative activity of La2O3, LaOCl, and LaCl3 in reaction with CCl4 studied with infrared spectroscopy and density functional theory calculations

Relative activity of La2O3, LaOCl, and LaCl3 in the destructive adsorption of CCl4 to CO2 was studied with density-functional theory calculations and temperature-programmed reaction experiments monitored with IR spectroscopy. Integral absorbance of the IR peak for phosgene, which is a reaction intermediate, was obtained as a function of temperature, and initial reaction temperatures were compared for different sample amounts of La2O3 and LaOCl. The initial reaction temperatures of about 390 K for La2O3 and 365 K for LaOCl were practically independent of the tested sample weights, and the lower temperature for LaOCl was attributed to a higher activity of surface sites on this material. Calculations suggest that CCl4 decomposition proceeds through a stepwise Cl donation from CCl4 to the surface and that the overall rate is controlled by the first step: CCl4 splitting into a Cl anion and CCl3 cation over an acid-base pair of surface sites. A lanthanum acid site in the pair initiates the split by interacting with one of the chlorine atoms in CCl4, and an oxygen base site stabilizes the remaining CCl3 fragment. Transition state estimates suggest that the relative activity of surface sites can be ranked in the following order: LaOCl > LaCl3 with a partially dechlorinated surface > La2O3. Surface Lewis acidity and basicity of these materials are summarized in terms of the vibrational frequency for adsorbed CO, energy of the lowest unoccupied molecular orbital, and proton affinity. Higher activity of LaOCl is attributed to the higher acidity of the lanthanum site, the higher basicity of the oxygen site, and the geometry of the acid-base pair of sites that allows them to interact with CCl4 simultaneously.     

FTIR study of the effects of water pretreatment on the acid sites and the dispersion of metal particles in Y zeolites and mordenites

FTIR results on zeolite-supported Pt and Pd show that the presence of water during metal reduction modifies both the acid and the metal functions of these catalysts. The water treatment eliminates Lewis acid sites and lowers the concentration of Brønsted acid sites by partial dealumination. At low temperature CO is adsorbed on Brønsted sites; the position of the corresponding FRIR band indicates that for Pt/HMOR, (MOR = mordenite) unlike Pt/HY, the intrinsic acid strength of these sites is increased by the wet reduction procedure. FTIR spectra after CO adsorption at room temperature show that wet reduction markedly improves the dispersion of Pt in HMOR; this effect is weaker for HY and absent for the Na forms of the zeolites. Bands of gem-Pt(CO)₂, which are indicative of very small, possibly electron-deficient Pt clusters, are detected in Pt/HMOR.     

Use of the IR spectra of adsorbed ethane and propane molecules to characterize the strength of active sites in zeolites and to analyze the activation of C-H bonds in these paraffins

The adsorption and activation of ethane and propane on the hydrogen and cationic forms of mordenite, zeolite ZSM-5, and zeolite Y were studied by diffuse-reflectance IR spectroscopy. The effect of the polarization of these molecules by adsorption sites on the intensities and shifts of absorption bands due to C-H stretching vibrations were studied. It was found that weak adsorption species were formed on the hydrogen forms of the above zeolites. In this case, both the intensity distributions and the positions of absorption bands due to C-H stretching vibrations were almost independent of the nature of zeolites. However, both absorption band maximum positions and relative intensity distributions changed upon paraffin adsorption on the cationic forms. It was also found that relative intensity distributions and shifts of absorption bands due to C-H stretching vibrations strongly depended on the nature of cations and zeolites. In this case, the initially totally symmetrical C-H vibrations were found most strongly disturbed. The low-frequency shifts and relative intensities of absorption bands due to these vibrations for various cations and zeolites were found to increase in the following orders: H < Na < Ca < Mg < Zn and zeolite Y < Mord ≈ ZSM-5. The experimental results suggest that ethane and propane molecules can be used as molecular probes for acquiring information on the nature and properties of acidbase sites in zeolites. In this case, both the low-frequency shifts and the relative intensities of absorption bands due to C-H stretching vibrations can be used as measures to characterize the nature of cations and zeolites. However, the latter was found to be much more sensitive to the nature of active sites.     

Electric Fields on FSM-16 Surface

The surface of mesoporous silicate, FSM-16, was investigated by infrared spectroscopy (IR) using methane and carbon monoxide as molecular probe. The appearance of 1-peak of adsorbed CH4 indicated the presence of electric field (1.4 × 105 esu) which is attributed to a weakly polarized free silanol site (site-1). The site was located at the void of oxygen framework in FSM-16 pore wall. In addition, the presence of site-2 without any electric field was found by IR spectra of adsorbed CO. The latter site was assigned to a interacted silanol groups and/or a Si–O–Si site.