Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

Structure and properties of H<Subscript>8</Subscript>(PW<Subscript>11</Subscript>TiO<Subscript>39</Subscript>)<Subscript>2</Subscript>O heteropoly acid

Heteropoly acid (HPA) H₈(PW₁₁TiO₃₉)₂O·xH₂O (I) is synthesized by three different ways and studied by chemical analysis, potentiometric titration, mass-spectrometry, IR, ³¹P, ¹⁸³W, and ¹⁷O NMR spectroscopy, thermogravimetry, and transmission electron microscopy. Anion I consists of two subparticles of the Keggin structure bridged by Ti-O-Ti. The dimeric anion exists in HPA aqueous solutions at [I] > 0.02 M. At pH > 0.6 it splits to a [PW₁₁TiO₄₀]⁵⁻ monomer stable up to pH ∼ 6. When heated (150–400)°C, I splits into H₃PW₁₂O₄₀ and, apparently, H₃PW₁₀Ti₂O₃₈ without phase separation. Thermolysis products are soluble and when dissolved in water turn again into I. Complete decomposition of I to oxides occurs at ∼450°C.     

Solid electrolytes with cesium-cationic conduction in the Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Cs<Subscript>2</Subscript>O system

New cesium-conducting solid electrolytes based on cesium monoferrite in the Fe₂O₃-TiO₂-Cs₂O system are synthesized and studied. It is found that the introduction of titanium dioxide significantly reduces the electronic component of conductivity, which prevails in pure CsFeO₂, and raises the ionic conductivity. The latter becomes predominant with increasing concentration of TiO₂. The effect of dimensional factor on the characteristics of electrolyte is shown. The optimal compositions studied have very high cesium-cationic conductivity: it is above 10⁻² S cm ⁻¹ at 300°C.     

Effect of heat treatment on electrochromic properties of TiO<Subscript>2</Subscript> thin films

Electrochromic titanium oxide (TiO₂) films were deposited on ITO/glass substrates by chemical solution deposition (CSD). The stock solutions were spin-coated onto substrates and then heated at various temperatures (200–500 °C) in various oxygen concentrations (0–80%) for 10 min. The effects of the processing parameters on the electrochromic properties of TiO₂ films were investigated. X-ray diffraction measurements demonstrated that the amorphous TiO₂ films were crystallized to form anatase films above 400 °C. The electrochromic properties and transmittance of TiO₂ films were measured in 1 M LiClO₄–propylene carbonate (PC) non-aqueous electrolyte. An amorphous 350 nm-thick TiO₂ film that was heated at 300°C in 60% ambient oxygen exhibited the maximum transmittance variation (ΔT%), 14.2%, between the bleached state and the colored state, with a ΔOD of 0.087, Q of 10.9 mC/cm², η of 7.98 cm²/C and x in Li _x ClO₄ of 0.076 at a wavelength (λ) of 550 nm.     

Electrochemical and magnetic characterization of LiFePO<Subscript>4</Subscript> and Li<Subscript>0.95</Subscript>Mg<Subscript>0.05</Subscript>FePO<Subscript>4</Subscript> cathode materials

A series of lithium iron phosphates was synthesized via the sol–gel route. Iron phosphides, which are electronic conductors, were formed when sintered at 850°C. Magnetic susceptibility measurements on the samples show antiferromagnetic behaviour with T _N=50±2 K for LiFePO₄ and Li_0.95Mg_0.05PO₄ sintered at temperatures below 850°C. The LiFePO₄ and Li_0.95Mg_0.05FePO4 cathodes show a stable electrochemical capacity in the range of 150–160 mA h/g on cycling. The cyclability deteriorates with increasing sample sintering temperature due to the increased crystal size and impurities.     

Mixed conductivity and stability of A-site-deficient Sr(Fe,Ti)O<Subscript>3–δ</Subscript> perovskites

Deficiency in the A sublattice of perovskite-type Sr_{1– y} Fe_0.8Ti_0.2O_3–δ (y=0–0.06) leads to suppression of oxygen-vacancy ordering and to increasing oxygen ionic conductivity, unit cell volume, thermal expansion, and stability in CO₂-containing atmospheres. The total electrical conductivity, predominantly p-type electronic in air, decreases with increasing A-site deficiency at 300–700 K and is essentially independent of the cation vacancy concentration at higher temperatures. Oxygen ion transference numbers for Sr_{1– y} Fe_0.8Ti_0.2O_3–δ in air, estimated from the faradaic efficiency and oxygen permeation data, vary in the range from 0.002 to 0.015 at 1073–1223 K, increasing with temperature. The maximum ionic conductivity was observed for Sr_0.97Fe_0.8Ti_0.2O_3–δ ceramics. In the system Sr_0.97Fe_{1– x} Ti _x O_3–δ (x=0.1–0.6), thermal expansion and electron-hole conductivity both decrease with x. Moderate additions of titanium (up to 20%) in Sr_0.97(Fe,Ti)O_3–δ result in higher ionic conductivity and lower activation energy for ionic transport, owing to disordering in the oxygen sublattice; further doping decreases the ionic conduction. It was shown that time degradation of the oxygen permeability, characteristic of Sr(Fe,Ti)O_3–δ membranes and resulting from partial ordering processes, can be reduced by cycling of the oxygen pressure at the membrane permeate side. Thermal expansion coefficients of Sr_{1– y} Ti_{1– x} Fe _x O_3–δ (x=0.10–0.60, y=0–0.06) in air are in the range (11.7–16.5)×10^–6 K^–1 at 350–750 K and (16.6–31.1)×10^–6 K^–1 at 750–1050 K. Electronic Publication     

Lithium-conducting solid electrolytes of Li<Subscript>4</Subscript>GeO<Subscript>4</Subscript>-Li<Subscript>3</Subscript>PO<Subscript>4</Subscript> system with additions of zirconium ions

The effect of partial substitution of Zr⁴⁺ ions for Ge4+ ions in highly conducting lithium-cationic solid electrolyte Li_3.75Ge_0.75P_0.25O₄ is studied. It is found that the introduction of zirconium ions considerably raises the conductivity of basic electrolyte in the high-temperature range. For the optimal composition, the conductivity is 2.82 × 10⁻¹ S cm⁻¹ at 400°C and 1.55 S cm⁻¹ at 700°C. Possible reasons for the effects are discussed.     

Study of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> interaction with solid lithium-containing electrolytes

Compatibility of the lithium-titanium spinel Li₄Ti₅O₁₂ in contact with precursors of lithium-conducting solid electrolytes of composition Li_1.3Al_0.3Ti_1.7(PO₄)₃ (LATP), Li_1.5Al_0.5Ge_1.5(PO₄)₃ (LAGP), Li_0.5La_0.5TiO₃ (LLT) was studied. It was found that, in sintering of Li₄Ti₅O₁₂ brought in contact with LATP and LAGP, a solid-phase reaction occurs to give nonconducting phases (TiO₂ and Li₃PO₄). The conductivity of the stable composite Li₄Ti₅O₁₂/LLT (10%) is higher than that of the starting Li₄Ti₅O₁₂, which makes it possible to regard the composite as a promising anode material for lithium-ion batteries.     

Aqueous sol–gel processing of precursor oxides for ZrW<Subscript>2</Subscript>O<Subscript>8</Subscript> synthesis

This paper describes the synthesis of ZrW₂O₈ by the use of an aqueous citrate-gel method in order to prepare a fine, pure and homogeneous oxide mixture suitable for ceramic processing. The thermal expansion coefficient thus obtained for α-ZrW₂O₈ is −10.6 × 10⁻⁶ °C⁻¹ (50–125 °C) whereas for the β-ZrW₂O₈ a value of −3.2 × 10⁻⁶ °C⁻¹ (200–300 °C) is obtained. The advantages of the use of a sol–gel method is expressed in the very homogeneous end-products. The paper describes crystallographic data, morphological structure and the thermal expansion properties of the ZrW₂O₈ material. Moreover, photoluminescence and photochromic properties specific to the precursor gel are described and analyzed. These effects support our views that the precursors show homogeneity up to nanometer level.     

Impedance studies on the 5-V cathode material,LiCoPO<Subscript>4</Subscript>

Olivine-structured LiCoPO₄ is synthesized by a Pechini-type polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld-refined X-ray diffraction, scanning electron microscopy, Brunauer, Emmett, and Teller surface area technique, infrared spectroscopy, and Raman spectroscopy techniques, respectively. The ionic conductivity (σ ionic), dielectric, and electric modulus properties of LiCoPO₄ are investigated on sintered pellets by impedance spectroscopy in the temperature range, 27–50 °C. The σ (ionic) values at 27 and 50 °C are 8.8 × 10⁻⁸ and 49 × 10⁻⁸ S cm⁻¹, respectively with an energy of activation (E _a) = 0.43 eV. The electric modulus studies suggest the presence of non-Debye type of relaxation. Preliminary charge–discharge cycling data are presented.     

Chemisorption of SO<Subscript>2</Subscript> on the Zn-modified In<Subscript>2</Subscript>O<Subscript>3</Subscript> surface

Chemisorption of SO₂ and O₂ on the In₂O₃ surface containing a zinc additive (0.4–2.7 at.%) was studied in a temperature range of 22–200 °C. At least three forms of sorbed SO₂ exist on the modified In₂O₃ surface. The temperature affects the contribution of single forms of SO₂ sorption and, hence, the change in the electric conductivity. The preliminary sorption of O₂ favors the formation of a donor form of chemisorbed SO₂. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2228–2232, October, 2005.     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Facile preparation and electrochemical properties of large-scale Li<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> nanobelts

Large-scale Li_1+x V₃O₈ nanobelts were successfully fabricated using filter paper as deposition substrate through a simple surface sol–gel method. The nanobelts were as long as tens of micrometers with widths of 0.4–1.0 μm and thickness of 50–100 nm. The nanobelts were characterized by X-ray diffration (XRD), Fourier infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM). The formation mechanism of the nanobelts was investigated, showing that the morphology of the nanobelts is mainly determined by the calcination temperature. Electrochemical properties of the Li_1+x V₃O₈ nanobelts were characterized by charge–discharge experiments, and the results demonstrate that the Li_1+x V₃O₈ nanobelts exhibit a high discharge capacity (278 mAh g⁻¹) and excellent cycling stability.     

XAFS investigation of [Pd(NH<Subscript>3</Subscript>)<Subscript>4</Subscript>][AuCl<Subscript>4</Subscript>]<Subscript>2</Subscript> and its thermolysis products

Thermolysis of double complex salt [Pd(NH₃)₄][AuCl₄]₂ has been studied in helium atmosphere from ambient to 350 °C. The XAFS of Pd K and Au L₃ edges and thermogravimetry measurements have been carried out to characterize the intermediates and the final product. In the temperature range 115–160 °C the complex is decomposed to form Pd(NH₃)₂Cl₂ and AuCl_4−x N _x species with x ranging from 2 to 3. Subsequent heating of the intermediate up to 300 °C leads to the total loss of NH₃. The Au–Cl and Au–Au bonds form the local environment of Au at the stage of decomposition while only four chlorine atoms are around Pd. At the temperature of 330 °C the Au and Pd nanoparticles as well as residues of palladium chloride are detected. The final product consists of separated Au and Pd nanoparticles.     

Synthesis,structure, and electric properties of oxygen-deficient perovskites Ba<Subscript>3</Subscript>In<Subscript>2</Subscript>ZrO<Subscript>8</Subscript> and Ba<Subscript>4</Subscript>In<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>11</Subscript>

Perovskite phases Ba₃In₂ZrO₈ and Ba₄In₂Zr₂O₁₁ with the nominal concentration of structural oxygen vacancies 1/9 and 1/12, respectively, were synthesized by solid-phase and solution methods. X-ray diffraction showed cubic symmetry of both phases with the unit cell parameter a = 0.4193(2) and 0.4204(3) nm, respectively. The absence of superstructural lines resulted in the conclusion on statistical arrangement of oxygen vacancies. Thermogravimetry and mass spectrometry proved that both phases can reversibly absorb water from gas phase (pH₂O = 2 × 10⁻² atm) with observed correlation between the concentration of oxygen vacancies and amount of absorbed water. The total water amount was up to 0.9 mol per formula unit or, if recalculated for perovskite unit ABO₃, 0.3 and 0.23 mol H₂O, respectively. The temperature curves of coductivity in the atmosphere with various partial water vapor pressures (pH₂O = 3 × 10⁻⁵ and 2 × 10⁻² atm) showed significantly higher conductivity and lower activation energy (0.52 eV) in humid atmosphere due to proton transfer. The proton conductivity is up to 5 × 10⁻⁴ Ohm⁻¹ cm⁻¹ at 300°C for Ba₃In₂ZrO₈ specimen. IR spectrometry showed that protons in the structure exist primarily in OH-groups.     

Low-temperature performance of Li-ion cells with a LiBF<Subscript>4</Subscript>-based electrolyte

The effect of LiBF₄ on the low-temperature performance of a Li-ion cell was studied by using a 1:1:1 (wt) EC/DMC/DEC mixed solvent. The results show that the LiBF₄-based electrolyte has a 2- to 3-fold lower ionic conductivity and shows rather higher freezing temperature compared with a LiPF₆-based electrolyte. Owing to electrolyte freezing, cycling performance of the Li-ion cell using LiBF₄ was significantly decreased when the temperature fell below –20 °C. However, impedance data show that at –20 °C the LiBF₄ cell has lower charge-transfer resistance than the LiPF₆ cell. In spite of the relatively lower conductivity of the LiBF₄-based electrolyte, the cell based on it shows slightly lower polarization and higher capacity in the liquid temperature range (above –20 °C) of the electrolyte. This fact reveals that ionic conductivity of the electrolytes is not a limitation to the low-temperature performance of the Li-ion cell. Therefore, LiBF₄ may be a good salt for the low-temperature electrolyte of a Li-ion cell if a solvent system that is of low freezing temperature, high solubility to LiBF₄, and good compatibility with a graphite anode can be formulated. Electronic Publication     

Characteristics of Ag/Bi<Subscript>3.25</Subscript>La<Subscript>0.75</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript>/p-Si heterostructure prepared by sol-gel processing

The metal-ferroelectric-semiconductor (MFS) heterostructure has been fabricated using Bi_3.25La_0.75Ti₃O₁₂ (BLT) as a ferroelectric layer by sol-gel processing. The effect of annealing temperature on phase formation and electrical characteristics of Ag/BLT/p-Si heterostructure were investigated. The BLT thin films annealed at from 500°C to 650°C are polycrystalline, with no pyrochlore or other second phases. The C-V curves of Ag/BLT/p-Si heterostructure annealed at 600°C show a clockwise C-V ferroelectric hysteresis loops and obtain good electrical properties with low current density of below 2×10⁻⁸ A/cm² within ±4 V, a memory window of over 0.7 V for a thickness of 400 nm BLT films. The memory window enlarges and the current density reduces with the increase of annealing temperature, but a annealing temperature over 600°C is disadvantageous for good electrical properties.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

Thermal behaviour and properties of Na<Subscript>2</Subscript>O-TiO<Subscript>2</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Differential scanning calorimetry (DSC) and thermomechanical analysis (TMA) were used to study the thermal behaviour of (50-x)Na₂O-xTiO₂-50P₂O₅ and 45Na₂O-yTiO₂-(55-y)P₂O₅ glasses. The addition of TiO₂ to the starting glasses (x=0 and y=5 mol% TiO₂) resulted in a nonlinear increase of glass transition temperature and dilatation softening temperature, whereas the thermal expansion coefficient decreased. All prepared glasses crystallize under heating within the temperature range of 300–610°C. The contribution of the surface crystallization mechanism over the internal one increases with increasing TiO₂ content. With increasing TiO₂ content the temperature of maximum nucleation rate is also gradually shifted from a value close to the glass transition temperature towards the crystallization temperature. X-ray diffraction measurements showed that the major compounds formed by glass crystallization were NaPO₃, TiP₂O₇ and NaTi₂(PO₄)₃. The chemical durability of the glasses without titanium oxide is very poor, but with the replacement of Na₂O or P₂O₅ by TiO₂, it increases sharply.