Preparation of a novel fluorescence probe based on covalent immobilization by emulsion polymerization and its application to the determination of metronidazole

A novel method of preparing fluorescence particle probe by emulsion polymerization with covalent immobilization of indicator dye was described. A terminal double bond was attached to 3-amino-9-ethylcarbazole (AEC) via methacryloyl chloride, and the resultant compound was copolymerized with butyl methacrylate. The obtained polymer particles were used as a fluorescence probe, which is almost free of dye leaching, and has higher photostability and lower toxicity in comparison with free AEC. This probe holds great potential for the applications in intracellular measurements. In present study the prepared probe was used for the determination of metronidazole. The results revealed that the probe showed good selectivity and had a linear response to the analyte in the range from 2.0 × 10⁻⁵ to 1.0 × 10⁻³ mol l⁻¹ with a detection limit of 9.0 × 10⁻⁶ mol l⁻¹.     

Molecularly imprinted polymer-based potentiometric sensor for degradation product of chemical warfare agents: Part I. Methylphosphonic acid

A biomimetic potentiometric sensor for the specific recognition of methylphosphonic acid (MPA), the degradation product of nerve agents sarin, soman, VX, etc., was designed. This involves the preparation of MPA imprinted polymer particles and removal of the template by soxhlet extraction. Subsequently, the leached MIP particles were dispersed in 2-nitrophenyloctyl ether (plasticizer) and embedded in polyvinyl chloride matrix. The sensor responds to MPA in the concentration range 5 × 10⁻⁸ to 1 × 10⁻⁴ and 1 × 10⁻³ to 1 × 10⁻¹ M with a detection limit of 5 × 10⁻⁸ M. The selectivity of the sensor has been tested with respect to chemical analogues such as phosphoric acid, sodium dihydrogen phosphate, organophosphorous pesticide and triazine herbicides. The utility of the sensor was tested for field monitoring of MPA in spiked ground water.     

Microbiosensor for acetylcholine and choline based on electropolymerization/sol–gel derived composite membrane

Amperometric enzyme biosensors for the determination of acetylcholine (ACh) and choline (Ch) have been described. For the fabrication of the biosensors, N-acetylaniline (nAN) was first electropolymerized on a Pt electrode surface to be served as a permselective layer to reject interferences. Bovine serum albumin (BSA) and choline oxidase (CHOD) were co-immobilized in a zinc oxide (ZnO) sol–gel membrane on the above modified Pt electrode for a Ch sensor, or CHOD, acetylcholinesterase (AChE) and BSA immobilized together for an ACh/Ch sensor. The poly (N-acetylaniline) (pnAN) film was the first time used for an ACh/Ch sensor and found to have excellent anti-interference ability, and the BSA in the sol–gel can improve the stability and activity of the enzymes. Amperometric detection of ACh and Ch were realized at an applied potential of +0.6 V versus SCE. The resulting sensors were characterized by fast response, expanded linear range and low interference from endogenous electroactive species. Temperature and pH dependence and stability of the sensor were investigated. The optimal ACh/Ch sensor gave a linear response range of 1.0 × 10⁻⁶ to 1.5 × 10⁻³ M to ACh with a detection limit (S/N = 3) of 6.0 × 10⁻⁷ M and a linear response range up to 1.6 × 10⁻³ M to Ch with a detection limit of 5.0 × 10⁻⁷ M. The biosensor demonstrated a 95% response within less than 10 s.     

Zn(II)-selective membrane electrode based on tetra(2-aminophenyl) porphyrin

A new PVC membrane electrode for Zn²⁺ ions based on tetra(2-aminophenyl) porphyrin (TAPP) as membrane carrier is prepared. The sensor exhibits a linear stable response over a wide concentration range (5.0×10⁻⁵ to 1.0×10⁻¹ M) with a slope of 26.5 mV/decade and a limit of detection 3.0×10⁻⁵ M (1.96 ppm). It has a response time of about l0 s and can be used for at least 8 months without any divergence in potential. The propose membrane sensor revealed good selectivities for Zn²⁺ over a wide variety of other metal ions and can be used in pH range of 3.0–6.0. It was successfully applied to the direct determination of zinc in a pharmaceutical sample and also as an indicator electrode in potentiometric titration of Zn²⁺ ions.     

Kinetic method for the determination of traces of thyroxine by its catalytic effect on the Mn(III) metaphosphate-As(III) reaction

A new, highly sensitive and simple kinetic method for the determination of thyroxine was proposed. The method was based on the catalytic effect of thyroxine on the oxidation of As(III) by Mn(III) metaphosphate. The kinetics of the reaction was studied in the presence of orthophosphoric acid. The reaction rate was followed spectrophotometrically at 516 nm. It was established that orthophosphoric acid increased the reaction rate and that the extent of the non-catalytic reaction was extremely small. A kinetic equation was postulated and the apparent rate constant was calculated. The dependence of the reaction rate on temperature was investigated and the energy of activation and other kinetic parameters were determined.

Thyroxine was determined under the optimal experimental conditions in the range 7.0 × 10⁻⁹ to 3.0 × 10⁻⁸ mol L⁻¹ with a relative standard deviation up to 6.7% and a detection limit of 2.7 × 10⁻⁹ mol L⁻¹. In the presence of 0.08 mol L⁻¹ chloride, the detection limit decreased to 6.6 × 10⁻¹⁰ mol L⁻¹. The proposed method was applied for the determination of thyroxine in tablets. The accuracy of the method was evaluated by comparison with the HPLC method.     

Square wave adsorptive stripping voltammetric determination of famotidine in urine

Electrochemical studies of famotidine were carried out using voltammetric techniques: cyclic voltammetry, linear sweep and square wave adsorptive stripping voltammetry. The dependence of the current on pH, buffer concentration, nature of the buffer, and scan rate was investigated. The best results for the determination of famotidine were obtained in MOPS buffer solution at pH 6.7. This electroanalytical procedure enabled to determine famotidine in the concentration range 1 × 10⁻⁹–4 × 10⁻⁸ mol L⁻¹ by linear sweep adsorptive stripping voltammetry (LS AdSV) and 5 × 10⁻¹⁰–6 × 10⁻⁸ mol L⁻¹ by square wave adsorptive stripping voltammetry (SW AdSV). Repeatability, precision and accuracy of the developed methods were checked. The detection and quantification limits were found to be 1.8 × 10⁻¹⁰ and 6.2 × 10⁻¹⁰ mol L⁻¹ for LS AdSV and 4.9 × 10⁻¹¹ and 1.6 × 10⁻¹⁰ mol L⁻¹ for SW AdSV, respectively. The method was applied for the determination of famotidine in urine.     

Determination of folic acid by chemiluminescence based on peroxomonosulfate-cobalt(II) system

Based on the chemiluminescence (CL) phenomena of folic acid in peroxomonosulfate-cobalt(II) system, a rapid and sensitive CL method was developed for determination of folic acid in pharmaceutical preparations and its urinary metabolism processes. Under the optimum conditions, the relative CL intensity was linear over the concentration ranging from 10⁻⁹ to 8 × 10⁻⁷ mol L⁻¹ (R² = 0.9991) with a detection limit as low as 6 × 10⁻¹⁰ mol L⁻¹ (S/N = 3) and relative standard deviation was 2.63% for 2 × 10⁻⁸ mol L⁻¹ folic acid (n = 11). This method has been successfully applied to the determination of folic acid in tablets and human urine. The blank CL emission was yielded owing to the formation of singlet oxygen molecular pair from the quenching experiment of 1,4-diazabicyclo[2.2.2]octane, and pterine-6-carboxylic acid might be the degradation intermediate in this system and it also acts an energy acceptor and sensitizes the chemiluminescence based on the studies of the CL and fluorescence spectra.     

Highly selective and sensitive copper(II) membrane coated graphite electrode based on a recently synthesized Schiff’s base

A PVC membrane electrode based on bis-2-thiophenal propanediamine (TPDA) coated directly on graphite is described. The electrode exhibits a Nernstian response for Cu²⁺ over a very wide concentration range (1.0×10⁻¹ to 6.0×10⁻⁸ M) with a detection limit of 3.0×10⁻⁸ M (2.56 ng ml⁻¹). It has a fast response time and can be used for at least 2 months without any major deviation. The proposed sensor revealed very good selectivities for Cu²⁺ over a wide variety of other metal ions and could be used in the pH range of 3.0–7.0. It was successfully used for direct determination of copper in black tea and as an indicator electrode in potentiometric titration of copper ion.     

Time measurement-visual analysis of nickel(II) using autocatalytic reaction with sodium sulfite/hydrogen peroxide system and its application to the length detection-flow analysis

Trace amounts of nickel(II) can function as a trigger (=reaction initiator) in an autocatalytic reaction with the sodium sulfite/hydrogen peroxide system. Based on this finding, sub-μg L⁻¹ levels of nickel(II) were determined by a time measurement using the autocatalytic reaction. The detection range using the above method was 10⁻⁹–10⁻⁵ M, the detection limit (3σ) was 8.1 × 10⁻¹⁰ M (0.047 μg L⁻¹), and the relative standard deviation was 2.66% at nickel(II) concentration of 10⁻⁷ M (n = 7). This method was applied to length detection-flow injection analysis. The detection range for the flow injection analysis was 2 × 10⁻⁹–2 × 10⁻³ M. The detection limit (3σ) was 1.4 × 10⁻⁹ M (0.082 μg L⁻¹), and the relative standard deviation was 1.86 at initial nickel(II) concentration of 10⁻⁶ M (n = 7).     

Sensitive determination of phenylephrine and chlorprothixene at poly(4-aminobenzene sulfonic acid) modified glassy carbon electrode

Phenylephrine (i.e. PHE) and chlorprothixene (i.e. CPT), two effective and important antipsychotic drugs with low redox activity, were found generating an irreversible anodic peak at about +0.89 V (vs. SCE) and +1.04 V in 0.05 M HAc–NaAc (pH 5.0) or NH₂CH₂COOH–HCl (pH 2.4) buffer solution at poly(4-aminobenzene sulfonic acid) modified glassy carbon electrode (i.e. poly(4-ABSA)/GC), respectively. Sensitive and quantitative measurement for them based on the anodic peaks was established under the optimum conditions. The anodic peak current was linear to PHE and CPT concentrations from 1 × 10⁻⁷ to 1.5 × 10⁻⁵ M and 2 × 10⁻⁶ to 4.5 × 10⁻⁵ M, the detection limits obtained were 1 × 10⁻⁸ and 1 × 10⁻⁷ M, separately. The modified electrode exhibited some excellent characteristics including easy regeneration, high stability, good reproducibility and selectivity. The method proposed was successfully applied to the determination of PHE and CPT in drug injections or tablets and proved to be reliable compared with ultraviolet spectrophotometry. The modified electrode was characterized by electrochemical methods.     

Iodide-selective carbon paste electrodes based on recently synthesized Schiff base complexes of Fe(III)

A new modified carbon paste electrode (CPE) based on a recently synthesized Schiff base complex of Fe(III) as a suitable carrier for I⁻ ion is described. The electrode exhibits a super Nernstian slope of 71.0±0.3 mV per decade for I⁻ ion over a wide concentration range from 1.0×10⁻⁶ to 5.0×10⁻¹ M, with a low detection limit of 6.5×10⁻⁷ M. It has a relatively fast response time, a satisfactory reproducibility and relatively long life time. The proposed sensor shows a fairly good selectivity toward I⁻ ion in comparison to other common anions. The potentiometric response is independent of the pH of the test solution in the pH range 3.5–10.0. Spectrophotometric studies confirmed the redox-type response mechanism of the electrode toward iodide ion. The proposed electrode was used as an indicator electrode in potentiometric titration of iodide ion.     

Voltammetric determination of glucose based on reduction of copper(II)–glucose complex at lanthanum hydroxide nanowire modified carbon paste electrodes

A novel voltammetric method for the determination of β-d-glucose (GO) is proposed based on the reduction of Cu(II) ion in Cu(II)(NH₃)₄²⁺–GO complex at lanthanum(III) hydroxide nanowires (LNWs) modified carbon paste electrode (LNWs/CPE). In 0.1 mol L⁻¹ NH₃·H₂O–NH₄Cl (pH 9.8) buffer containing 5.0 × 10⁻⁵ mol L⁻¹ Cu(II) ion, the sensitive reduction peak of Cu(II)(NH₃)₄²⁺–GO complex was observed at −0.17 V (versus, SCE), which was mainly ascribed to both the increase of efficient electrode surface and the selective coordination of La(III) in LNW to GO. The increment of peak current obtained by deducting the reduction peak current of the Cu(II) ion from that of the Cu(II)(NH₃)₄²⁺–GO complex was rectilinear with GO concentration in the range of 8.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 3.5 × 10⁻⁷ mol L⁻¹. A 500-fold of sucrose and amylam, 100-fold of ascorbic acid, 120-fold of uric acid as well as gluconic acid did not interfere with 1.0 × 10⁻⁵ mol L⁻¹ GO determination.     

The nano-Au self-assembled glassy carbon electrode for selective determination of epinephrine in the presence of ascorbic acid

Gold nanoparticles were self-assembled to the modified glassy carbon electrode (GC) with cysteamine (CA) to prepare the nano-Au/CA/GC modified electrode. The electrochemical behavior of epinephrine (EP) on the modified electrode was explored with cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Epinephrine gave a pair of redox peaks at E_pa = 0.190 mV and E_pc = −0.224 mV (versus SCE), respectively. The nano-Au/CA/GC modified electrode shows an excellent electrocatalytic activity for the oxidation of EP. The modified electrode could be used to determine EP in the presence of ascorbic acid (AA). The response of catalytic current with EP concentration shows a linear relation in the range of 1.0 × 10⁻⁷ to 5.0 × 10⁻⁴ mol L⁻¹ with the correlation coefficient of 0.998. The detection limit is 4.0 × 10⁻⁸ mol L⁻¹. The modified electrode exhibited a good reproducibility, sensitivity and stability for the determination of EP injection.     

Application of lead film electrode for simultaneous adsorptive stripping voltammetric determination of Ni(II) and Co(II) as their nioxime complexes

An adsorptive stripping voltammetric (AdSV) procedure for simultaneous determination of Ni(II) and Co(II) in the presence of nioxime as a complexing agent at an in situ plated lead film electrode was described. The Co(II) signal was enhanced by exploitation of the catalytic process in the presence of nitrite. Ni(II) and Co(II) signals are better separated than in the case of bismuth film electrodes. Calibration graphs for an accumulation time of 120 s are linear from 1 × 10⁻⁹ to 1 × 10⁻⁷ mol L⁻¹ and from 1 × 10⁻¹⁰ to 5 × 10⁻⁹ mol L⁻¹ for Ni(II) and Co(II), respectively. The proposed procedure was applied for Ni(II) and Co(II) determination in water certified reference materials.     

A bromide selective polymeric membrane electrode based on Zn(II) macrocyclic complex

A novel bromide ion-selective PVC membrane sensor based on 2,3,10,11-tetraphenyl-1,4,9,12-tetraazacyclohexadeca-1,3,9,11-tetraene zinc(II)complex (I) as carrier has been developed. The electrode exhibited wide working concentration range 2.2 × 10⁻⁶ to 1.0 × 10⁻¹ M and a limit of detection as 1.4 × 10⁻⁶ M with a Nernstian slope of 59.2 ± 0.5 mV per decade. The response time of electrode was 20 s over entire concentration range. The electrode possesses the advantages of low resistance, fast response and good selectivities for bromide over a variety of other anions and could be used in a pH range of 3.5–9.5. It was successfully used as an indicator electrode in the potentiometric titration of bromide ions with silver ion and also in the determination of bromide in real samples.     

Voltammetric study of the interaction of ciprofloxacin-copper with nucleic acids and the determination of nucleic acids

The behavior of the ciprofloxacin (CPFX) complex with copper, Cu(II)L₂, at a mercury electrode has been investigated in borax–boric acid buffer. The adsorption phenomena were observed by linear sweep voltammetry. The mechanism of the electrode reaction was found to be reduction of Cu(II)L₂ adsorbed on the surface of the electrode by an irreversible charge transfer to metal amalgam, Cu(0)(Hg). In the presence of DNA, the formation of the electrochemically non-active complexes Cu(II)L₂–DNA results in the decrease of the equilibrium concentration of Cu(II)L₂ and its peak current. Under the optimum conditions, the decrease of the peak current is proportional to DNA concentration. The linear ranges are 6.67×10⁻⁸ to 1.20×10⁻⁵ g ml⁻¹ for calf thymus DNA (ctDNA), 3.30×10⁻⁸ to 2.33×10⁻⁶ g ml⁻¹ for fish sperm DNA (fsDNA) and 1.0×10⁻⁸ to 1.2×10⁻⁶ g ml⁻¹ for yeast RNA. The detection limits are 5.00×10⁻⁹, 3.00×10⁻⁹ and 2.50×10⁻⁹ g ml⁻¹, respectively. This method exhibits good recovery and high sensitivity.     

An iron(III) ion-selective sensor based on a μ-bis(tridentate) ligand

A μ-bis(tridentate) ligand named 2-phenyl-1,3-bis[3′-aza-4′-(2′-hydroxyphenyl)-prop-4-en-1′-yl]-1,3-imidazolidine (I) has been synthesized and scrutinized to develop iron(III)-selective sensors. The addition of sodium tetraphenyl borate and various plasticizers, viz., chloronaphthalene, dioctylphthalate, o-nitrophenyl octyl ether and dibutylphthalate has been used to substantially improve the performance of the sensors. The membranes of various compositions of the ligand were investigated and it was found that the best performance was obtained for the membrane of composition (I) (10 mg):PVC (150 mg):chloronaphthalene (200 mg):sodium tetraphenyl borate (9 mg). The sensor showed a linear potential response to iron(III) over wide concentration range 6.3 × 10⁻⁶ to 1.0 × 10⁻¹ M (detection limit 5.0 × 10⁻⁶ M) with Nernstian slope (20.0 mV/decade of activity) between pH 3.5 and 5.5 with a quick response time of 15 s. The potentiometric selectivity coefficient values as determined by match potential method (MPM) indicate excellent selectivity for Fe³⁺ ions over interfering cations. The sensor exhibits adequate life of 2 months with good reproducibility. The sensor could be used in direct potentiometry.     

Interactions of mercury(II), lead(II), calcium(II), aluminium(III) or ferric(III) nitrate with single and double chain linear alkylbenzenesulfonates in aqueous and sea-water media

The solubility products of mercury(II) and lead(II) dodecylbenzenesulfonates were calculated on the basis of light scattering measurements at 20°C to be (9.33 ± 0.90) × 10⁻¹³ and (1.03 ± 0.10) × 10⁻¹² respectively. The investigations of precipitation phenomena performed in diluted natural sea-water ([Cl⁻] = 10⁻¹² mol dm ⁻³), including tenside and added heavy metal ions, showed similar behaviour for all metal dodecylbenzenesulfonates investigated in this work, i.e. the synergistic effect of tenside, of added electrolyte, and of cations and anions from sea-water. A comparison made by a statistical test of significance, chosen to measure agreement between the estimates of the solubility constants obtained in aqueous solutions and in the above mentioned sea-water solution, showed a noticeable effect, evident particularly in the case of mercury(II). The precipitation of tenside and metal nitrates in natural sea-water ([Cl⁻] = 5 × 10⁻¹ mol dm⁻³) covers a wide concentration region of dodecylbenzenesulfonic acid (from high concentrations to 5 × 10⁻⁶ mol dm⁻³) and from high metal nitrate concentrations to very low. The microscopic textures of phases precipitated in the systems with sea-water obviously confirmed favouring formation of the liquid crystalline phase.     

Chelating ionophore based membrane sensors for copper(II) ions

Acetylacetone, ethylacetoacetate and salicyldehyde, are reported to form chelates with copper of high stability as compared to other metals. Therefore, PVC based membranes of bis[acetylacetonato] Cu(II) (A), bis[ethylacetoacetate] Cu(II) (B) and bis[salicyldehyde] Cu(II) (C) have been investigated as copper(II) selective sensors. The addition of sodium tetraphenylborate and various plasticizers, viz., DOS, TEHP, DOP, DBP and TBP have been found to substantially improve the performance of the sensors. The membranes of various compositions of the three chelates were investigated and it was found that the best performance was obtained for the membrane of composition A (1%): PVC (33%): TBP (65%): NaTPB (1%). The sensor shows a linear potential response to Cu(II) over wide concentration range 2.0 × 10⁻⁶ to 1.0 × 10⁻¹ M (detection limit 0.1 ppm) with Nernstian compliance (29.3 mV decade⁻¹ of activity) between pH 2.6 and 6.0 with a fast response time of 9 s. The potentiometric selectivity coefficient values as determined by match potential method (MPM) indicate excellent selectivity for Cu²⁺ ions over interfering cations. The sensor exhibits adequate shelf life (3 months) with good reproducibility (S.D. ±0.2 mV). The sensor has been used in the potentiometric titration of Cu²⁺ with EDTA. The utility of the sensor has been tested by determining copper in vegetable foliar and multivitamin capsule successfully.     

Electrochemiluminescent behavior of allopurinol in the presence of Ru(bpy)(3)(2+)

The electrochemiluminescent (ECL) response of allopurinol was studied in aqueous media over a wide pH range (pH 2–13) using flow injection (FI) analysis. It was revealed that allopurinol itself had no ECL activity, but could greatly enhance the ECL of Ru(bpy)₃²⁺ in alkaline media giving rise to a sensitive FI-ECL response. The effects of experimental conditions including the mode of applied voltage signal, the potential of working electrode, pH value, the flow rate of carrier solution, and the concentration of Ru(bpy)₃²⁺ and allopurinol on the ECL intensity were investigated in detail. The most sensitive FI-ECL response of allopurinol was found at pH 12.0, where the FIA-ECL intensity showed a linear relationship with concentration of allopurinol in the range 1 × 10⁻⁸ mol L⁻¹ to 5 × 10⁻⁷ mol L⁻¹, and the detection limit was 5 × 10⁻⁹ mol L⁻¹.